Cambridge 650BD User Manual [nl]

Your music + our passion

650BD

azur

ENGLISH

Blu-ray player

User’s manual

Contents

Introduction..................................................................................................3

Important safety instructions......................................................................4

Limited warranty..........................................................................................6

Compatible disc types .................................................................................6

Rear panel connections ..............................................................................8

Front panel controls and display ................................................................9

Remote control..........................................................................................10

Connecting to the Internet........................................................................11

Audio connections.....................................................................................12

Analogue video connections ....................................................................13

HDMI connections.....................................................................................13

Setting up the player using the Easy Setup.............................................14

Accessing the Easy Setup Wizard ........................................................14

Choose the primary video output.........................................................14

Select the best output resolution.........................................................14

Determine the display aspect ratio......................................................15

Select the audio setting........................................................................15

Operating instructions...............................................................................16

Picture-in-Picture and Secondary Audio (BONUSVIEW) ......................17

BD-Live ...................................................................................................17

Output resolution ..................................................................................18

TV system selection ..............................................................................18

Other media playback...............................................................................19

Connecting a USB Drive........................................................................19

Setup Menu for more advanced setup....................................................21

Playback Setup......................................................................................22

Video Setup ...........................................................................................23

Audio Format Setup...............................................................................24

Audio signal reference chart ................................................................26

Recommended audio format 0ptions..................................................27

Audio Processing setup.........................................................................27

Speaker Conﬁguration ..........................................................................27

Other Audio Processing Settings..........................................................29

Device Setup .........................................................................................29

Network Setup.......................................................................................30

Picture Adjustment................................................................................31

Appendix - language code list...................................................................32

Technical speciﬁcations............................................................................33

Troubleshooting .........................................................................................33

Make sure you register your purchase.

Visit: www.cambridge-audio.com/care

By registering, you’ll be the first to know about:

Future product releases

Software upgrades

News, events and exclusive offers plus competitions!

This guide is designed to make installing and using this product as easy as possible. Information in this document has been carefully checked for accuracy at the time of printing; however, Cambridge Audio's policy is one of continuous improvement, therefore design and speciﬁcations are subject to change without prior notice.

This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior written permission of the manufacturer. All trademarks and registered trademarks are the property of their respective owners.

Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby Laboratories.

Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,392,195; 7,272,567; 7,333,929; 7,212,872 & other U.S. and worldwide patents issued & pending. DTS is a registered trademark and the DTS logos, Symbol, DTS-HD and DTS-HD Master Audio are trademarks of DTS, Inc. © 1996-2008 DTS, Inc. All Rights Reserved.

"HDMI","HDMI logo" and "High-Deﬁnition Multimedia Interface" are trademarks or registered trademarks of HDMI Licensing LLC.

"Blu-ray Disc", "BONUSVIEW" and "BD-Live" are trademarks of Blu-ray Disc Association.

Java and all Java-based trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc. in the United States and other countries.

DVD Logo is a tr ademark of DVD Format/Logo Licensing Corp., registered in the U.S., Japan and other countries.

Super Audio CD, SACD and the SACD logo are joint trademarks of Sony Corporation and Philips Electronics N.V. Direct Stream Digital (DSD) is a trademark of Sony Corporation.

"AVCHD" and the "AVCHD" logo are trademarks of Panasonic Corporation and Sony Corporation.

Designed for Windows Media, Microsoft, HDCD, and the HDCD logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.

650BDazur

ENGLISH

Introduction

Thank you for purchasing this Cambridge Audio Azur Blu-ray Player. Like all Cambridge Audio products, the 650BD adheres to three core principles – stunning performance, ease of use and incredible value.

The 650BD features almost universal disc compatibility and can play back CD, HDCD, DVD-Video, DVD-Audio, Super Audio CD and Blu-Ray discs. 24/192kHz Digital to Analogue converters and our usual careful audio design ensure that the 650BD can reproduce the dynamics and scale required for modern movie soundtracks whilst also being able to reproduce a genuinely musical performance with either stereo or multichannel music discs.

A full range of HDMI, digital and analogue outputs are ﬁtted. These allow the connection of suitably equipped TVs and AV receivers.

The latest surround-sound formats are supported including decoding of Dolby True HD, Dolby Digital Plus, DTS-HD Master Audio and DTS-HD High Resolution Audio in Stereo, 5.1 or 7.1 variants. In particular support for the true lossless Dolby True HD and DTS HD Master Audio formats provides unprecedented audio ﬁdelity from Blu-ray discs.

The 650BD is also capable of outputting all of these formats as bitstreams over HDMI for decoding in a suitable AV Receiver. Video of up to 1080p resolution from BD discs at 50/60Hz or 24fps can be output over HDMI whilst the 650BD can process DVDs to provide an upscaled 1080p output.

Also featured is an environmentally friendly low power (1W) standby circuit.

All this proprietary engineering is housed within our low resonance, acoustically damped chassis. An Azur Navigator remote control is also provided, giving full remote control of your Blu-ray player and if required a Cambridge Audio ampliﬁer or AV receiver in an attractive and easy to use handset.

Remember your 650BD can only be as good as the system it is connected to. Please do not compromise on your AV receiver or speaker package and always use good quality video and audio cabling. Naturally we particularly recommend AV receivers such as the matching 650R from the Cambridge Audio Azur range, which has been designed to the same exacting standards as this product. Your dealer can also supply excellent quality Cambridge Audio interconnects to ensure your system realises its full potential.

Thank you for taking the time to read this manual; we recommend you keep it for future reference.

Matthew Bramble Cambridge Audio Technical Director and the 650BD design team

Important safety instructions

For your own safety please read the following important safety instructions carefully before attempting to connect this unit to the mains power supply. They will also enable you to get the best performance from and prolong the life of the unit:

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not ﬁt into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles and the point where they exit from the apparatus.

11. Only use attachments/accessories speciﬁed by the manufacturer.

12. Use with only the cart, stand, tripod, bracket, or table speciﬁed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has been damaged in any way, such as the power-supply cord or plug having been damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

This product utilises a Laser. Use of controls or adjustments or performance of procedures other than those speciﬁed herein may result in hazardous radiation exposure. Do not open covers and do not repair yourself. Refer servicing to qualiﬁed personnel.

This label is located on the laser protective housing inside the product.

WARNING – To reduce the risk of ﬁre or electric shock, do not expose this unit to

rain or moisture.

– Batteries (battery pack or batteries installed) shall not be exposed to

excessive heat such as sunshine, ﬁre or the like.

The unit is of Class 1 construction and must be connected to a mains socket outlet with a protective earthing connection.

The unit must be installed in a manner that makes disconnection of the mains plug from the mains socket outlet (or appliance connector from the rear of the unit) possible. Where the mains plug is used as the disconnect device, the disconnect device shall remain readily operable. Only use the mains cord supplied with this unit.

Please ensure there is ample ventilation (at least 10cm clearance all round). Do not put any objects on top of this unit. Do not situate it on a rug or other soft surface and do not obstruct any air inlets or outlet grilles. Do not cover the ventilation grilles with items such as newspapers, tablecloths, curtains, etc.

This unit must not be used near water or exposed to dripping or splashing water or other liquids. No objects ﬁlled with liquid, such as vases, shall be placed on the unit.

The lightning ﬂash with the arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of un-insulated ‘dangerous voltage’ within the product’s enclosure that may be of sufﬁcient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the service literature relevant to this appliance.

WEEE symbol

The crossed-out wheeled bin is the European Union symbol for indicating separate collection for electrical and electronic equipment. This product contains electrical and electronic

equipment which should be reused, recycled or recovered and should not be disposed of with unsorted regular waste. Please return the unit or contact the authorised dealer from whom you purchased this product for more information.

CE mark

This product complies with European Low Voltage

(2006/95/EC), Electromagnetic Compatibility (2004/108/EC) and Environmentally-friendly design of Energy-related Products (2009/125/EC) Directives when used and installed according to this instruction manual. For continued compliance only Cambridge Audio accessories should be used with this product and servicing must be referred to qualiﬁed service personnel.

C-Tick mark

This product meets the Australian Communications Authority’s

Radio communications and EMC requirements.

Ross Test Stamp

This product meets Russian electronic safety approvals.

650BDazur

ENGLISH

FCC regulations

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER AUTHORITY TO OPERATE THE EQUIPMENT.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Re-orient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

Ventilation

IMPORTANT – The unit will become hot when in use. Do not stack multiple

units on top of each other. Do not place in an enclosed area such as a bookcase or in a cabinet without sufﬁcient ventilation.

Ensure that small objects do not fall through any ventilation grille. If this happens, switch off immediately, disconnect from the mains supply and contact your dealer for advice.

Positioning

Choose the installation location carefully. Avoid placing it in direct sunlight or close to a source of heat. No naked ﬂame sources, such as lighted candles, should be placed on the unit. Also avoid locations subject to vibration and excessive dust, cold or moisture. The unit can be used in a moderate climate.

This unit must be installed on a sturdy, level surface. Do not place in a sealed area such as a bookcase or in a cabinet. Do not place the unit on an unstable surface or shelf. The unit may fall, causing serious injury to a child or adult as well as serious damage to the product. Do not place other equipment on top of the unit.

Due to stray magnetic ﬁelds, turntables or CRT TVs should not be located nearby due to possible interference.

Electronic audio components have a running in period of around a week (if used several hours per day). This will allow the new components to settle down and the sonic properties will improve over this time.

Power sources

The unit should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power-supply to your home, consult your product dealer or local power company.

This unit can be left in Standby mode when not in use and will draw <1W in this state. To turn the unit off, switch off at the rear panel. If you do not intend to use this unit for a long period of time, unplug it from the mains socket.

Overloading

Do not overload wall outlets or extension cords as this can result in a risk of ﬁre or electric shock. Overloaded AC outlets, extension cords, frayed power cords, damaged or cracked wire insulation and broken plugs are dangerous. They may result in a shock or ﬁre hazard.

Be sure to insert each power cord securely. To prevent hum and noise, do not bundle the interconnect leads with the power cord or speaker leads.

Cleaning

To clean the unit, wipe its case with a dry, lint-free cloth. Do not use any cleaning ﬂuids containing alcohol, ammonia or abrasives. Do not spray an aerosol at or near the unit.

Battery disposal

Please dispose of any discharged batteries according to local environmental/electronic waste disposal guidelines.

Connections

Before making any connections, make sure all power is turned off and only use suitable interconnects.

Servicing

These units are not user serviceable. Never attempt to repair, disassemble or reconstruct the unit if there seems to be a problem. A serious electric shock could result if this precautionary measure is ignored. In the event of a problem or failure, please contact your dealer.

Plug-ﬁtting Instructions (UK only)

The cord supplied with this appliance is factory-ﬁtted with a UK mains plug ﬁtted with a 3-amp fuse inside. If it is necessary to change the fuse, it is important that a 3-amp fuse is used. If the plug needs to be changed because it is not suitable for your socket, or becomes damaged, it should be cut off and an appropriate plug ﬁtted following the wiring instructions below. The plug must then be disposed of safely, as insertion into a mains socket is likely to cause an electrical hazard. Should it be necessary to ﬁt a 3-pin BS mains plug to the power cord, the wires should be ﬁtted as shown in this diagram. The colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug. Connect them as follows:

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter ‘N’ or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is marked with the letter ‘L’ or coloured RED.

The wire which is coloured GREEN/YELLOW must be connected to the terminal which is marked with the letter ‘E’ or coloured GREEN.

If a standard 13-amp (BS 1363) plug is used, a 3-amp fuse must be ﬁtted or, if any other type of plug is used, a 3-amp or 5-amp fuse must be ﬁtted, either in the plug or adaptor, or on the distribution board.

Compatible disc types

BD-Video

High Deﬁnition Blu-ray movie and music discs in BD-ROM, BD-RE and BDR formats.

Blu-ray Discs with virtual packages or Picture-in- Picture functions.

Blu-ray Discs with interactive features when the player is connected to the Internet.

DVD-Video

DVD movie discs in DVD+RW/DVD+R/DVD-RW/DVD-R formats.

DVD-Audio

DVD format discs containing multi-channel or stereo high resolution audio of up to 24/96 5.1 or 24/192 resolution with video or still pictures. Some DVD-Audio discs also contain a DVD-Video portion.

Super Audio CD

High resolution audio-only discs with stereo and/or multi-channel audio recorded in a special bitstream format called DSD. Hybrid discs with both high resolution DSD and CD-compatible layers are supported.

Compact Disc

Compact Discs (CD-DA) and CD-R, CD-RW discs.

High-deﬁnition digital video camera format.

Discs that cannot be played

• BDs with cartridge

• DVD-RAMs

• HD DVDs

• Data portion of CD-Extras

• BD-Video/DVD-Video with a different region code to the Blu-ray player you have purchased.

• Some DualDiscs: A DualDisc is a two sided disc with DVD on one side and digital audio on the other side. The digital audio side does not generally meet the technical speciﬁcations of the Compact Disc Digital Audio (CD-DA) format so playback is not guaranteed.

• Music discs encoded with copyright protection technologies: among such discs, some again do not conform to the CD standard so playback is not guaranteed.

Limited warranty

Cambridge Audio warrants this product to be free from defects in materials and workmanship (subject to the terms set forth below). Cambridge Audio will repair or replace (at Cambridge Audio's option) this product or any defective parts in this product. Warranty periods may vary from country to country. If in doubt consult your dealer and ensure that you retain proof of purchase.

To obt ain wa rra nty ser vice , plea se cont act th e Cambr idg e Aud io authorised dealer from which you purchased this product. If your dealer is not equipped to perform the repair of your Cambridge Audio product, it can be returned by your dealer to Cambridge Audio or an authorised Cambridge Audio service agent. You will need to ship this product in either its original packaging or packaging affording an equal degree of protection.

Proof of purchase in the form of a bill of sale or receipted invoice, which is evidence that this product is within the warranty period, must be presented to obtain warranty service.

This warranty is invalid if (a) the factory-applied serial number has been altered or removed from this product or (b) this product was not purchased from a Cambridge Audio authorised dealer. You may call Cambridge Audio or your local country Cambridge Audio distributor to conﬁrm that you have an unaltered serial number and/or you made a purchase from a Cambridge Audio authorised dealer.

This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or modiﬁcation of, or to any part of, the product. This warranty does not cover damage due to improper operation, maintenance or installation, or attempted repair by anyone other than Cambridge Audio or a Cambridge Audio dealer, or authorised service agent which is authorised to do Cambridge Audio warranty work. Any unauthorised repairs will void this warranty. This warranty does not cover products sold AS IS or WITH ALL FAULTS.

REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE THE EXCLUSIVE REMEDY OF THE CONSUMER. CAMBRIDGE AUDIO SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY IN THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY LAW, THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES WHATSOEVER INCLUDING, BUT NOT LIMITED TO, THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PRACTICAL PURPOSE.

Some countries and US states do not allow the exclusion or limitation of incidental or consequential damages or implied warranties so the above exclusions may not apply to you. This warranty gives you speciﬁc legal rights, and you may have other statutory rights, which vary from state to state or country to country.

For any service, in or out of warranty, please contact your dealer.

650BDazur

ENGLISH

Disc care and handling BD-ROM compatibility

• To keep the disc clean from scratches or ﬁngerprints, handle the disc by its edge. Do not touch the recording surface.

• Blu-ray Discs record data in very high density and the record layer is very close to the disc surface. For this reason, Blu-ray Discs are more sensitive to dust and ﬁngerprints than DVD. Should you encounter playback problems and see dirty spots on the disc surface, clean the disc with a cleaning cloth. Wipe the disc from the centre out along the radial direction. Do not wipe the disc in a circular motion.

•Do not use record cleaning sprays or solvents such as benzene, thinner

and anti-static spray.

• Do not attach labels or stickers to discs as this may cause the disc to warp, become imbalanced or too thick, resulting in playback problems.

• Avoid exposing the discs to direct sunlight or heat sources.

• Do not use the following discs:

– Discs with exposed adhesive from removed stickers or labels. The

disc may get stuck inside the player.

– Warped or cracked discs.

– Irregularly shaped discs, such as heart or business card shapes.

Since the Blu-ray Disc speciﬁcations are new and evolving, some discs may not play properly depending on the disc type, version and encoding. It is possible that a Blu-ray disc manufactured after the player was manufactured uses certain new features of the Blu-ray Disc speciﬁcations. To ensure the best possible viewing experience, the player may need a ﬁrmware or software update from time to time.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Region management information

This player is designed and manufactured to respond to the region management information of DVD or BD discs. If the region number of a BD-Video or DVD disc does not correspond to the region number of this player, this player cannot play the disc.

BD-Video –This player plays BD-Video with marks that match the code on the back of the unit (i.e. A, B or C).

Discs that have no region coding are also playable. These usually have all 3 region codes on the packaging in a pyramid.

DVD-Video –This player plays DVD-Video with marks that match the region code on the back of the unit (i.e. 1, 2, 3, 4 or 5).

Discs that are encoded for All regions are also playable.

Rear panel connections

Digital outputs

Optical and Coaxial digital audio outputs, normally used to connect to a suitable Audio/Video Receiver for surround sound decoding (output must be set for "Bitstream" - refer to the "Audio setup" section). These outputs can also be used to connect to a separate DAC or digital recording device (output must be set for "LPCM" - refer to the "Audio setup" section).

Toslink Optical - Use a high quality TOSLINK ﬁbre optic cable.

S/P DIF Co-Axial Digital - Use a high quality 75 ohm digital RCA/Phono

interconnect cable designed speciﬁcally for digital audio use.

Analogue video outputs

Component - Connect to the YCbCr or YPbPr terminals of a television set

via three 75 ohm RCA/phono cables designed speciﬁcally for video use.

Composite - Connect to your television via 75 ohm RCA/phono cable designed speciﬁcally for video use.

S-Video - Connect to your television via dedicated S-Video cable.

HDMI Out

HDMI (High-Deﬁnition Multi-Media Interface) is a purely digital connection that can carry both audio and video. Use a dedicated HDMI cable to connect to a TV/Monitor or AV Receiver with a compatible HDMI input.

IR (Infra-Red) Emitter In

Allows modulated IR commands from multi-room systems or IR repeater systems to be received by the unit.

Ethernet LAN port

Used for discs supporting BD-Live that provide interactive features when the player is connected to the Internet.

USB port

Port for interfacing to a ﬂash/memory card or "Mass Storage Device".

Notes:

• Only USB 2.0 certiﬁed products with the USB 2.0 logo on them are supported by the 650BD. Please either consult the manufacturer of the USB 2.0 product to make sure it is properly certiﬁed, or go to www.usb.org for a list of approved products, before purchase. We cannot be held responsible for any incompatibility issues.

• This unit supports

"USB Mass Storage Class Bulk-Only Transport"

devices only. Most USB thumbs drives, portable hard disk drives and card readers conform to this device class. Other USB devices such as MP3 players, digital cameras, and mobile phones may not be compatible.

• Supported USB drives must be formatted with the FAT (File Allocation Table) or FAT32 ﬁle system. Drives formatted with NTFS ﬁle system are not supported.

7.1 channel analogue audio output

If Down-mix is set to "7.1 C H " in the Speaker Setup page (Down-mix mode section) of the 650BD’s Setup menus, these sockets provide 7.1 output from the 650BD's built in Surround-Sound decoder. This can be used to connect to the 7.1 audio line-level inputs of an ampliﬁer/AV receiver or ampliﬁed speaker package if required. Similarly, Down-mix can be set to

"5.1 CH" to provide 5.1 output. If Down-mix is set to "LT/RT", "Stereo" or "V.S urro und" the Left and Right outputs only are active and provide a

stereo or stereo downmixed output. Refer to the "Speaker conﬁguration" section of this manual for more information.

AC power socket

Once you have made all audio and video connections, plug the IEC type AC power cable into the rear of the unit and an appropriate mains socket then switch on. Your 650BD is now ready for use.

2 7643 8

650BDazur

ENGLISH

Front panel

Front panel display

Standby/On

Switches the unit between Standby mode (indicated by a dim power LED) and On (indicated by a bright power LED). Standby is a low power mode where the power consumption is less than 1 watt. The unit should be left in Standby mode when not in use.

USB port

Port for interfacing to a ﬂash/memory card or "Mass Storage Device".

Notes:

• Only USB 2.0 certiﬁed products with the USB 2.0 logo on them are supported by the 650BD. Please either consult the manufacturer of the USB 2.0 product to make sure it is properly certiﬁed, or go to www.usb.org for a list of approved products. We cannot be held responsible for any incompatibility issues.

• This unit supports

"USB Mass Storage Class Bulk-Only Transport"

devices only. Most USB thumb drives, portable hard disk drives and card readers conform to this device class. Other USB devices such as MP3 players, digital cameras, and mobile phones may not be compatible.

• Supported USB drives must be formatted with the FAT (File Allocation Table) or FAT32 ﬁle system. Drives formatted with NTFS ﬁle system are not supported.

IR sensor

Receives IR commands from the supplied Azur Navigator remote control. A clear unobstructed line of sight between the remote control and the sensor is required.

Display

Used to display the 650BD’s functions and playback state, etc. Please refer to the front panel display section at right for more information.

Disc tray

Use the Open/Close button to activate.

Open/Close

Allows you to open and close the disc tray for loading of discs. Pressing Play will also close the tray and start playing a disc if one is loaded.

Play/Pause

Plays the disc and pauses (freezes) playback.

Stop

Press once to stop playback. Pressing Play will cause the playback to be re-started from the same position. Press Stop again to fully stop playback.

Skip

Press once to skip between tracks/chapters.

1. Disc Type Indication – Indicates the currently playing disc type.

2. Track/Chapter – When illuminated, the displayed time applies to a

track or chapter.

3. Title/Group – When illuminated, the displayed time applies to a title or group.

4. Total – When illuminated, the displayed time is the total play time.

5. Remaining – When illuminated, the displayed time is the remaining

play time.

6. Playback Status – Indicates playback status such as Play, Pause, Repeat, Repeat All, Random/Shufﬂe, and A-B Repeat.

7. Angle Icon – Indicates that the scene contains additional camera angle(s) that can be selected.

8. HDMI – Indicates that the HDMI output is active.

9. Network – Indicates that the unit is connected to a network.

10. Mute Icon – Indicates that the audio is muted.

11. Audio Channel Indication – Indicates whether the audio is 2ch stereo

or multi-channel surround.

12. Main Display – Text messages and numeric display.

13. Audio Type Indication – Indicates the type of audio tracks playing.

2 3

9876

123245 6789

10 11 12 13

Remote control

The Azur 650BD is supplied with a remote control. Insert the 3 supplied AAA batteries to activate. For further details of the various adjustment functions available, refer to the later sections of this manual.

Opens and closes the disc tray.

Switches the unit between On and Standby mode.

0-9 Numerical buttons

Used to enter numeric values such as the number of a desired chapter or track to go to.

Info

Show/hide On-Screen Display.

Page!/ Page"

Show previous/next page.

Go to Home Menu to select media source.

Go To

Press once to bring up an OSD bar showing (from left to right) Playing Status, Title, Chapter, Time Counter, Progress Indicator, and Total Time. After pressing the Go To button for the ﬁrst time, the cursor will be positioned at the Time Counter. This is the “Time Search” mode. Each subsequent press of the Go To button moves the cursor from Time to Chapter to Title and back round. Use the Numerical or Nagivation button to enter the hours, minutes and seconds for your speciﬁed search and press the Enter button.

Clear

Press to remove outstanding track programs.

Top Menu

Show BD top menu or DVD title menu.

Pop Up Menu

Show BD pop-up menu or DVD menu.

Setup

Press to enter the Setup menu. Please refer to the "Blu-ray player setup" section of this manual for more information.

Pure Audio

Turn video off/on.

!"#$Navigation

Press the directional arrows to move around menus.

Enter

Press to accept the item/function highlighted in the menu.

Press to play or pause playback.

Press to stop current playback.

Press to return to the previous menu.

Audio/Subtitle

Press once to access alternate audio soundtracks on the disc (if available on the disc).

Press and hold to access Subtitle function. When pressed for a few seconds, the Subtitle function will cycle through available languages.

Scan forwards and backwards

()

Right Skip –Press once to skip forward by one track/chapter on the disc.

Left Skip –Press once to skip backward by one track/chapter on the disc.

Colour buttons

These button functions vary by the content. See later section of the manual.

A-B/Repeat

Press to mark a segment between A and B for repeated playback. The ﬁrst press marks point A, the second press marks point B.

Press and hold to access Repeat function. When pressed for a few seconds, the Repeat function will cycle as follows:

DVD and DVD- Audio –Repeat Chapter, Repeat Title, Repeat All, Repeat Off.

Blu-ray Disc – Repeat Chapter, Repeat Title, Repeat Off.

CD and SACD – Repeat One, Repeat All, Repeat Off.

SAP/PIP

Press to turn Secondary Audio Program on/off. Press and hold to cycle show/hide Picture-in-Picture. Refer to later section of the manual.

Angle/Zoom

Press to access various camera angles (if available on the disc). Press and hold to cycle through the various zoom magniﬁcations (and back to normal display).

Note: These features may not be available with certain DVD or Blu-ray discs.

Res/TV Type

Press to switch output resolution. Press and hold to cycle through TV system output between PAL, NTSC or Multi. Refer to later section of the manual.

Important information if you are using a Cambride Audio ampliﬁer or AV receiver

Amp/AVR buttons

The 650BD remote also has buttons that allow control of a Cambridge Audio azur ampliﬁer or AV receiver.

Note: These buttons are default set to transmit codes for our Azur 640R or 650R AV Receivers.

To set the re mote to an Az ur 340R or 54 0R in stead, simply remove the batteries, leave the remote for a few minutes and then hold down the Source button whilst reinserting the batteries.

To c ont rol an Azu r st ereo Am pliﬁe r, fo llow th e sa me s teps as before, but hold down the Standby/ On/Mute button.

Source

Press repeatedly to scroll through the source inputs one by one.

Standby/On/Mute

Press to switch the ampliﬁer/AV receiver between Standby mode and On. Press and hold to mute/un-mute the ampliﬁer/AV receiver.

Volume

Press to decrease or increase the volume of the ampliﬁer/ AV Receiver.

650BDazur

ENGLISH

Connecting to the Internet

The 650BD supports the BD-Live feature offered on some Blu-ray Disc titles. BD-Live offers extra downloadable content and additional online interactive programs. The available BD-Live content varies by discs and studios, and may include additional subtitles, commentaries, movie trailers, games, and/or online chat.

Connecting the player to the Internet will also allow the player to obtain ﬁrmware updates via the Internet.

In order to utilize the BD-Live feature or update ﬁrmware via the Internet, the player needs to be connected to a broadband Internet connection. It is not necessary to connect to the Internet if you do not intend to use the BD-Live and online ﬁrmware updating functionality.

• Plug one end of a network cable (Category 5/5E straight through Ethernet cable) into the LAN port on the back of the unit.

• Plug the other end of the network cable into a LAN port on your broadband router or modem.

• Some network conﬁguration may be required. Please refer to the Network Setup section of the manual for more details.

• If you would like to connect the player to a broadband Internet connection via Wi-Fi, please use an Ethernet/wireless LAN media converter (also called a wireless bridge or a gaming adapter). These convert between Wi-Fi and Ethernet/Lan as supported by the 650BD. Refer to the operating instructions supplied with the media converter for details on how to conﬁgure it.

Note: Your broadband router must also support Wi-Fi access.

• Refer to the operating instructions supplied with the broadband router or modem, or contact the Internet service provider for questions related to setting up of a router or modem.

Note: Only connect the LAN port of the player to an Ethernet port that supports 10BASE-T or 100BASE-TX. Connecting to any other ports or jacks, such as a phone jack, can damage the player.

Network Cable

(Ethernet)

Internet

Broadband Router/Modem

Broadband Internet

connection

65BD Rear Panel

Analogue stereo

The analogue stereo outputs should be used for play back of CDs, DVDs etc in stereo through a conventional ampliﬁer or AV receiver with analogue stereo inputs.

Analogue stereo is also usually the best connection method for listening to CDs and other stereo discs for best possible sound quality. It is often a good idea to connect both the analogue stereo outputs (for CD playback) and digital audio outputs (for surround sound decoding) at the same time.

To connect an analogue stereo system to the 650BD, use stereo phono cables (stereo 2RCA-2RCA).

Digital audio

The digital audio outputs should be used to decode the surround-sound soundtracks of DVDs with an external AV Receiver (Note: Digital output must be set to "RAW" in the Audio setup page). The 650BD sends an undecoded audio bitstream to the AV Receiver for decoding into 5.1/7.1 etc.

Either a 75ohm co-axial cable designed for digital audio or a TOSlink ﬁbre optic cable should be used (only one at a time).

Note: It is also possible to output stereo digital audio from the Digital Outputs for recording on conventional CD-R/MD etc. machines, see section on 650BD setup.

Audio connections

Do not plug in the mains power lead or turn the unit on until all connections have been made.

Three types of audio only connection can be made between the 650BD and your stereo/AV system:

AV receiver with

5.1/7.1 analogue inputs

Front right speaker

Speaker diagram shown for 5.1 channel setup. For 7.1 add two rear speakers.

Surround right speaker

Front left

speaker

Surround left

speaker

Centre speaker

Subwoofer

AV receiver

Phono cable

(2RCA-2RCA)

7.1

Analogue 5.1/7.1

The 650BD is also capable of decoding Surround-Sound soundtracks itself and outputting these as analogue 5.1/7.1 depending on the settings in the Speaker setup page in the 650BD setup menu.

For 5.1, connect to an AV receiver or ampliﬁed speaker system, use 6 x phono/RCA cables.

For 7.1, connect to an AV receiver or ampliﬁed speaker system, use 8 x phono/RCA cables.

Note: It is also possible to make an HDMI audio/video connection which carries both audio and video in the same cable. See later section.

However, when making an HDMI connection i.e. to an AV receiver, it is also often preferable to make an additional audio connection for CD and/or SACD/DVD-A playback.

Analogue Stereo

Digital Audio

Analogue 5.1/7.1

650BDazur

ENGLISH

Analogue video connections

HDMI connections

The 650BD can output video in both fully digital (HDMI) and analogue (Composite, S-Video and Component) formats. If your TV set supports HDMI then this is the preferred format (see next section).

If your TV set supports only analogue video the preferred connection is (in declining order of quality) Component, then S-Video and ﬁnally Composite.

TV/Monitor

TV/MonitorTV/Monitor

Component - Connect with 75 ohm Component video cables (3RCA3RCA).

Composite - Connect with single 75 ohm video phono cable (RCARCA).

S-Video - Connect with S-Video cable.

HDMI cable

TV/Monitor with HDMI input

TV/Monitor

with HDMI

input

AV receiver

HDMI cable

Out In

Connection to a TV via an AV Receiver

Direct connection to a TV

HDMI (High-Deﬁnition Multi-Media Interface) is a digital connection that can carry both audio and video in one cable. Direct digital transfer of video and support for various types of high deﬁnition video content make this the best connection type for picture quality.

DVI output can be supported simply by using DVI to HDMI adaptors as these two connection types are compatible. When using DVI only video will be passed to the TV/Monitor. A Co-axial (SPDIF) or Optical (TOSlink) digital audio connection must be made from the 650BD to the AV receiver for it to be able to receive audio and decode surround sound etc.

Note: The Dolby Digital Plus, Dolby True HD, DTS HD High Resolution and DTS HD Master Audio can only be passed by the 650BD over HDMI.

As HDMI can carry both digital audio and video, HDMI can be used to connect to AV receivers that support this function for external decoding.

Setting up the player

Accessing the Easy Setup Wizard

When the player is turned on for the ﬁrst time, an Easy Setup Wizard screen will appear. This is a series of guided instructions designed to conﬁgure the basic settings for the unit.

Note: If the Easy Setup Wizard has previously been completed or cancelled, it will no longer initiate when you turn on the unit. To access Easy Setup Wizard again, press the Setup button on the remote control, select Device Setup, then Reset Factory Default. Select

"OK" to conﬁrm

loading the factory default settings. Once the factory default settings are loaded the Easy Setup Wizard will appear again.

To start the Easy Setup Wizard, please follow these steps:

1. Turn on the TV.

2. Turn on the player.

3. Switch the input selection on your TV so that the TV displays the signal

from the player. You should see the ﬁrst step of the Easy Setup Wizard.

The ﬁrst step of the Easy Setup Wizard gives you the opportunity to skip the entire wizard. If you are familiar with setting up audio/video equipment and would like to fully customize the player settings using its setup menu, you may use the !" buttons to select the

"Cancel" option,

then press the Enter button to exit the Easy Setup Wizard. Otherwise, to continue with the Easy Setup Wizard, select the "OK" option and press the ‘Enter button.

Choose the primary video output

The player can output HD video through its HDMI or component output terminals. By setting the "primary video output" option, the player can optimize video output for the selected terminal. The choices are "HDMI" and "Component". If you connect the player to the TV using an HDMI cable, please select "HDMI". If you connect the player to the TV using component video cables, please select "Component".

Note: HDMI is always the prefered option for best video quality.

To ma ke yo ur se lect ion , u se th e #$buttons to highlight the choice, and then press the Enter button to go to the next

Select the best output resolution

For the latest generation of 1080p, "Full HD" or "Tru e H D" TV displays, the best output resolution will naturally be 1080p. For all other digital televisions this will likely be 720p or 1080i. These are general recommendations that work for most users, but there can be exceptions. Advanced users may want to try all supported resolutions and choose the one that provides the best visual result.

The 650BD supports a special

"Source Direct" output resolution on its

HDMI output. This resolution is recommended for use with external video processors or high-end TVs with high quality scalers. In "Source Direct" mode, the player works as a "transport". It decodes video from the discs and then sends the raw video signal in its native resolution and format, without extra processing, to the external video processor or TV. The actual output resolution thus varies by content:

Content Source Direct Output Resolution

PAL DVD 576i NTSC DVD 480i Most Blu-ray Movies (ﬁlm-source) 1080p 23.976Hz or 1080p 24Hz Most Blu-ray TV shows or Concerts 1080i (video-source) SACD and DVD-Audio 1080i

Depending on your selection of

"Primary Video Output", the available

output resolution selections will differ. For the HDMI output, the following output resolutions are available:

Auto, 1080p, 1080i, 720p, 480p/576p, 480i/576i, and Source Direct. If

"Auto" is selected, the player will determine its output resolution based on

the best signal resolution that the TV can display.

For the component output, the following output resolutions are available: 1080i, 720p, 480p/576p and 480i/576i. Please refer to the speciﬁcation of your TV to ﬁnd the best resolution to use.

Press the #$buttons to select the desired output resolution, then press the Enter button. The player will apply the selected output resolution and ask you to conﬁrm the selection. If your TV supports the selected resolution, you will see a dialog box with a countdown clock. Use the ! button to highlight the

"OK" option and press the Enter button to save the

resolution setting. If your TV does not support the selected resolution, you may see a black screen or an error message. In this case please wait for 15 seconds and the Easy Setup screen will reappear. Select a dif ferent resolution that your TV can support.

650BDazur

ENGLISH

Select the audio setting

The Blu-ray disc format brings not only high resolution video, but also high bit rate audio such as Dolby Digital Plus, Dolby TrueHD, DTS-HD High Resolution and DTS-HD Master Audio. Blu-ray Discs may also include additional audio features such as menu click sound and Secondary Audio Program (SAP – audio associated with the secondary video in Picture-inPicture mode). Depending on the user preferences and other audio/video equipment connected to the player, the audio settings need to be adjusted to achieve the best result. The Easy Setup Wizard offers two basic selections to get you started.

The

"Compatible" setting conﬁgures audio output in a way that is generally

compatible with all types of equipment and content. If you connect the player to a television directly, or to a receiver with an HDMI 1.1/1.2 or optical/coaxial input, selecting the "Compatible" setting is recommended. When menu click sound and Secondary Audio Program are presented in the content, those will be mixed into the audio output.

The

"Advanced" setting conﬁgures audio output to send the original main

audio content to a connected receiver for decoding and reproducing. It requires a receiver capable of decoding all high bit rate audio formats. If you connect the player to a receiver supporting HDMI 1.3 and high bit rate audio formats (such as our 650R AV Receiver), selecting the

"Advanced" setting is recommended. Menu click sound and Secondary

Audio Program are turned off by default to preserve the original quality of the main audio content.

Press the !"buttons buttons to select one of the audio setting choices, and then press the Enter button. The two basic audio setting choices may not cover all situations. You can further customize the audio settings using the player’s Setup Menu.

Complete the Easy Setup Wizard

Once you have selected the audio setting, the initial Easy Setup Wizard is completed.

Press the Enter button to close the Easy Setup Wizard. Your player is now ready for use. You will see a background screen with a Cambridge Audio and Blu-ray Disc logo. Please follow the rest of the user manual for basic and advanced operations.

Note:

• In case you are not able to get a picture using the HDMI or component output, please connect the player to the TV using the composite video output, and then use the Setup Menu to adjust the player settings.

• Video up-conversion over the component output is only available for unencrypted discs such as home video and consumer-created contents. Most commercially pressed DVD discs are CSS-encrypted and will be limited to 480i/480p resolution. This restriction applies to the component output only. The HDMI output is protected with HDCP and has no such restriction.

Determine the display aspect ratio

Use to select the screen format to fit your TV screen.

4:3 PanScan - You can select this screen when connected to a 4:3 TV set. The widescreen picture will display on the full screen, but some parts of the video picture will be cut off automatically.

4:3 Letterbox - Alternatively you can select this screen when connected to a 4:3 TV set. The full widescreen picture is displayed on the screen with black strips on the top and bottom of the screen.

16:9 Wide - Select this screen when connected to a 16:9 widescreen TV set. The full picture will now normally be displayed with no picture cropping (unless the movie itself has black bars recorded into the video).

16:9 Wide/Auto - 16:9 (widescreen) as well as 4:3 sources will be displayed in their native aspect ratio. Please note that in this mode 4:3 sources will be displayed with black borders on both sides to maintain the correct 4:3 aspect ratio.

Note: If you are using a plasma or widescreen CRT display you will want to avoid leaving black bars on the screen for any length of time as you may encounter temporary "burn-in" where the display retains memory of the "used" part of screen and the unused (black bar) portions are clearly deﬁned on the screen during subsequent viewing sessions. The "16:9 Wide" mode is the best choice for these types of displays.

Press the !"buttons to select the proper aspect ratio for your TV, then press the Enter button.

Operating instructions

Getting started

Turn on the power of the 650BD, TV, ampliﬁer/AV receiver and any other components which are connected to the 650BD. Make sure the TV and the audio receiver are set to the correct input channel.

1. Press the Open/Close button to open the disc tray.

2. Place the disc on the tray, label side facing up.

3. The player will read the disc information and starts playback.

4. Depending on the content of the disc, a menu or navigation screen

may appear. Please use the (!"#$) navigation and Enter button to select the content to play.

5. To stop playback, press the % button.

6. To turn off the player, press the Standby/On button.

Note:

• During DVD and some Blu-ray Disc playback, pressing the % button for the ﬁrst time brings the player to a pre-stop mode. You can resume playback from the stopped point by pressing the "/& button. This prestop mode allows you to change the player settings and then resume playback. To completely stop playback, press the % button twice.

• Certain Blu-ray Discs with BD-Java technology do not support the prestop mode. Pressing the % button during playback of such discs will completely stop the disc. Pressing the "/&button once the disc is stopped will restart it from the very beginning.

• This unit featured an environmentally friendly low power (1W) standby circuit. If it is not to be used for a long time, unplug it from the household AC outlet.

• Do not put anything except a BD/DVD/CD sized disc into the tray, foreign objects may damage the mechanism.

• Do not force the tray by hand during the opening and closing operations.

• To avoid dirt and dust entering the mechanism, keep the disc tray closed when not in use.

• If the disc is seriously scratched or too dirty, the player may not be able to read it or play it.

• Never load more than one disc into the disc tray at one time.

Fast Forward/Rewind search

Press repeatedly to cycle between 1X, 2X, 3X, 4X and 5X playback speed (without sound) and back to normal playback. Press ' button for backwards playback options, or the ( button for forwards playback.

Note:

• Certain Blu-ray discs utilising the BD-Java technology may have their own fast forwarding and reversing control. The actual speed varies by disc, and a progress scale may be displayed by the disc.

Skip playback

1. Press ) once to skip forward by one track/chapter on the disc. Press

and hold to skip forwards through several tracks.

2. Press * once to skip backward by one track/chapter on the disc. Press

and hold to skip backwards through several tracks.

Go To

Press the Go To button on the remote once to access Time Search and enter the required time from the start of the disc as H:MM:SS (Hours, Minutes, Seconds) using the numerical keys or the (#$!") navigational buttons. Press twice to access Chapter Time Selection and enter the required time from the start of the chapter. Press three times to access the Display information.

Slow

When playing a BD/DVD, press the & button to pause playback and then press the ' or ( button to cycle round the various speeds of slow motion (1/16, 1/8, 1/4 and 1/2), forwards and backwards and back to normal speed. To exit playback, press the "/& button.

Note: Certain Blu-ray discs utilising the BD-Java technology may not support slow playback.

Pause and frame by frame

1. During playback, press the "/& button to temporarily pause the program. In this mode, a Pause icon will appear on the TV screen.

2. While a DVD or Blu-ray Disc is paused, press the * or ) button to reverse or advance the video frame-by-frame.

3. Press the "/& button to resume normal playback.

Repeat

Note: The Repeat function is available only during playback.

Press and hold the A-B/Repeat button to access Repeat function. When pressed for a few seconds, the Repeat function will cycle as follows:

DVD and DVD-Audio –Repeat Chapter, Repeat Title, Repeat All, Repeat Off.

Blu-ray Disc – Repeat Chapter, Repeat Title, Repeat Off.

CD and SACD – Repeat One, Repeat All, Repeat Off.

Note: The repeat chapter/title setting will be cleared when moving to other chapter or title. Certain Blu-ray discs may not allow the Repeat function.

A-B Repeat

1. Press the A-B button at your desired starting point. "A" appears brieﬂy on the TV screen.

2. Press the A-B button at your desired end point.

"A-B" appears brieﬂy

on the TV screen, and the repeat sequence begins.

3. To exit the sequence, press the A-B button.

Note:

• The A-B repeat section can only be set within the current title (for BD/DVD

video) or current track (for BD/DVD audio, Video CD and Audio CD).

• A-B repeat playback is not available with some scenes on BD/DVD.

• A-B repeat playback does not function during title, chapter, track or all

repeat playback.

On-Screen Display

1. During the playback of a BD/DVD disc, press the Info button on the remote control to show status information; For CD and SACD, the status information is shown automatically.

2. While the status information is shown, press the #$buttons to scroll through several display formats. The playback time information displayed on the front panel changes together with the on-screen display.

3. Press the Info button again to hide the on-screen display. The playback time information display on the front panel will remain in the selected format.

In addition to the playback time, the on-screen display may also contain the following information about the content currently playing:

Playback status –an icon indicating play, pause, and fast forward/reverse status.

Bit rate meter –an indication of the bit rate of the audio and video stream.

Current and total title numbers (DVD and Blu-ray Discs), title chapters (DVD and Blu-ray Discs) and total tracks (CD and SACD).

Audio information –current and totally available number of audio tracks, language, format, and channels.

Subtitle information –current and totally available number of subtitle tracks and language.

Video format information –encoding type, frame rate and original aspect ratio.

650BDazur

ENGLISH

Audio language (soundtrack) selection

1. To select the audio language, press and hold the Audio/Subtitle button on the remote control during playback.

2. Repeatedly pressing the Audio/Subtitle button cycles through all available audio soundtracks on the disc.

Note: The availability of languages and audio soundtracks varies by disc. Some BD/DVD-Audio discs allow audio track selection with the Audio button, while others require the user to select from the audio setup menu of the disc. When playing a SACD with both multi-channel and stereo contents, the Audio button can be used to switch between the two formats.

Subtitle selection

1. When playing a DVD, Blu-ray disc or other video programs recorded with subtitles, press and hold the Audio/Subtitle button on the remote control to select the desired subtitle.

2. Holding down the Audio/Subtitle button will cycle through all available subtitles.

3. To turn of f subtitles, hold down the Audio/Subtitle button until the subtitle is turned off.

Angle selection

1. When playing a DVD or Blu-ray Disc, an angle mark will be displayed on the screen when the player detects scenes recorded with multiple possible angles.

The angle mark is also shown on the front panel display.

2. Press and hold the Angle/Zoom button on the remote control to select the desired playing angle.

3. To resume normal playback, hold the Angle/Zoom button until the default angle is displayed.

Note: This function is available only when the discs are recorded with multiple angles. The Angle mark display shows when an alternative angle is available. The Angle mark display on the screen can be turned off using the Setup Menu of the player.

Zoom

To change the zoom level, press and hold the Angle/Zoom button on the remote control. Holding down the Angle/Zoom button will switch the zoom level in the following sequence: 2x, 3x, 4x, 1/2, 1/3, 1/4 then back to normal.

The zoom level is reset to 1:1 when the disc is ejected, or when the player is turned off.

Note: The Zoom feature may not be available when certain DVD or Blu-ray Discs are played because the disc author chooses to disable Zoom.

Blu-ray disc menu

1. Blu-ray discs usually contain a top menu and a pop-up menu. The top menu normally appears at the beginning of the playback, after the previews and copyright messages. The Pop-up Menu can be accessed during playback without interruption.

2. During playback, press the Pop-up Menu button to access the pop-up menu. Press the Top Menu button to access the top menu.

3. Navigate the menu using the (!"#$) Navigation buttons, and then press the Enter button to make the selection.

4. Some menus make use of the colour buttons. You can select menu functions by pressing the corresponding Colour button on the remote control.

DVD disc menu

1. Some DVD discs contain title menu or chapter menu functions.

2. During playback, press the Top Menu button to return to the disc title menu. Press the Pop-Up Menu button to display the chapter menu. Depending on the disc, one or both menus may not exist.

3. Navigate the menu using the (!"#$) Navigation buttons, and then press the Enter button to make the selection.

4. Press the Return button to return to the previous menu. The return location varies by disc.

Memory and automatic resume

The player automatically remembers the current position for a disc when playback is interrupted. Operations such as Open/Eject or turning Power off will cause the player to save the current playing position for that disc.

The position is memorised even after turning off the unit or changing the disc.

When the next time the same disc is played back, the player will recognize the saved playing position. Playback will automatically resume from this saved position. However if you wish to cancel the automatic resume and start playback from the beginning, you may press the % button when prompted.

The player can remember playback position for up to ﬁve discs. When the sixth disc is memorised, the oldest one is replaced.

Note: Some Blu-ray discs do not support resuming and will always play from the beginning.

Picture-in-Picture and Secondary Audio

Certain Blu-ray discs contain secondary video (Picture-in-Picture/PIP) and secondary audio. This feature is often called BONUSVIEW. When such a disc is played, a Picture-in-Picture mark (PIP Mark) and a Secondary Audio Program Mark (SAP Mark) may be displayed on the screen to alert you to the availability of the secondary audio/video content.

The disc menu usually features interactive controls to turn on/off the Picture-in-Picture video and Secondary Audio Program. Please use those controls to select the desired secondary audio/video content.

There is also a PIP button on the remote control. If the disc menu does not offer interactive Picture-in-Picture controls, please use this button to turn on/off Picture-in-Picture or select from multiple secondary video programs.

Similarly there is a SAP button on the remote control. If the disc menu does not offer interactive secondary audio controls, please use this button to turn on/off Secondary Audio Program or select from multiple secondary audio tracks. Secondary Audio Programs are generally only available when Picture-in-Picture is shown.

Note:

• This function is available only when the discs are recorded with

secondary video and audio programs.

• Discs may not always be played back according to the PIP and SAP

remote buttons. Certain discs can ignore or override the remote control commands.

• The PIP and SAP Marks on the screen (which alert the user to the

presence of these functions on the disc) can be turned off using the Setup Menu of the player.

Some Blu-ray disc titles are released with the BD-Live feature. BD-Live offers extra downloadable contents and additional online interactive programs. The available BD-Live content varies by disc and studio, and may include additional subtitles, commentaries, preview trailers, games, and online chat. The player needs to be connected to the Internet in order to play BD-Live contents.

Operating instructions continued

Depending on how the studios organise their BD-Live contents, some Blu-ray discs may start downloading BD-Live content when playback starts; some have a BD-Live selection on its main menu; some may show a prompt to ask whether you would like to start downloading; and some may ask you to sign up for a membership or account. Please follow the instructions that come with the disc to enjoy BD-Live contents.

You r I ntern et conne cti on speed , t he overa ll Inter net tr afﬁc sit uat ion an d the capacity of the BD-Live content servers can all affect how fast BDLive content can be downloaded. If you encounter slow downloading or intermittent playback, please play the disc without accessing the BD-Live features, or try again at a different time.

When you use the BD-Live feature, the player or disc ID and your IP (Internet Protocol) address may be sent to the content provider via the Internet. Generally, no personally identiﬁable information is sent. However technologies exist to match your IP address to a certain geographical area or service provider. Your Internet service provider also has the knowledge of who is using which IP address. If the BD-Live content provider requires you to login using a membership or account, the content provider will have access to your membership or account information. Please check with your Internet service provider and the BD-Live content providers for their privacy policy.

You ca n al so cho os e to re str ict BD -Li ve a cc ess us ing th e pl aye r’s Se tup Me nu.

Output resolution

If you would like to change the output resolution, you may do so by pressing the Res/TV Type button on the remote control:

1. Make sure the video cable is properly connected.

2. Turn on the TV. Make sure the correct input is selected.

3. Make sure that the player is turned on. Although the output resolution can be changed

"on the ﬂy", it is recommended that you stop playback

and take out the disc before changing the output resolution. Press the Res/TV Type button. A "Resolution Setting" menu appears on the TV screen. In case the TV does not support the current resolution and you cannot see the "Resolution Setting" menu, the current resolution is also displayed on the front panel.

4. Use the !"buttons to select the new output resolution. Pressing the Res/TV Type button cycles through the available output resolutions. The new resolution is displayed on the front panel just in case you cannot see the

"Resolution Setting" menu (if it is incompatible with your

TV).

5. Press the Enter button to apply the selected output resolution. Or, if you do not want to change the output resolution, press the button.

The following output resolutions are available:

PAL out put via HDM I –Auto, 1080p, 1080i, 720p, 576p, 576i, Source Direct.

NTSC output via HDMI –Auto, 1080p, 1080i, 720p, 480p, 480i, Source Direct.

PAL output via component – 1080p*, 1080i, 720p, 576p, 576i.

NTSC output via component – 1080p*, 1080i, 720p, 480p, 480i.

* When 1080p is selected with component output selected as the primary video output, HDMI output resolution will be 1080p and component output resolution will be 1080i.

Note:

• Some TV sets do not support one more output resolutions (particularly

1080p). If an incompatible output resolution is selected, you will get a blank screen or an error message. In this case please select an output resolution that is supported by the TV.

• In case you are not able to get a picture using the HDMI or component

output, please connect the player to the TV using the composite video output, then use the Setup menu to adjust the player settings.

• Video up-conversion over the component output is only available for

unencrypted discs such as home video and consumer-created contents. Most commercially pressed DVD discs are CSS-encrypted and will be limited to 480i/480p resolution. This restriction applies to the component output only. The HDMI output is protected with HDCP and has no such restriction.

TV system selection

The 650BD can be set to output all video as PAL or NTSC or output the video in the same format it was recorded in (Multi). Some TVs only support PAL or NTSC and not both so forcing the output type to one or the other can be useful.

Press and hold the Res/TV Type button on the remote control to cycle the video output to PAL, NTSC or

"Multi" system. The TV screen displays the

selected system name.

Some points to keep in mind:

• When the video output is set to PAL or NTSC, the player will convert the disc content if different to the selected system.

• When the video output is set to

"Multi", the player will not perform

system conversion and will output the video in its native format on the disc. The "Multi" mode should only be used if your TV supports both NTSC and PAL systems.

• Some TV sets only support one of the PAL or NTSC systems. If the wrong output is selected, the TV may not display a picture. In this case keep holding the Res/TV Type button until a supported system is selected.

• The output system selected with the Res/TV Type button will be remembered when the player is turned off. The output system selection can also be done by setting the

"TV System" item in the "Video Setup"

section of the player’s Setup Menu.

Viewing pictures on DVD-Audio discs

Some DVD-Audio discs contain static pictures, such as photos of the band or narration of the album. When a DVD-Audio track is playing, you may use the Page !"buttons to select the picture.

Note: Availability of static pictures depends on the DVD-Audio disc.

Pure Audio mode

You can enjo y hi ghe r qu ali ty a udi o by turn ing of f th e vi deo pro ces sin g an d output. The Pure Audio mode reduces any potential interference between the video and audio signals.

1. Press the Pure Audio button on the remote control to turn off video

and enter Pure Audio mode. Video output will be turned off.

2. Press the Pure Audio button again to resume video and cancel Pure

Audio mode.

Note:

• Pure Audio mode is automatically cancelled when the unit is switched off or when playback is stopped.

• Since HDMI carries audio together with video, the HDMI output cannot be completely turned off. A black screen (inactive video but sync is still present) is transmitted instead to minimize any potential interference.

Shufﬂe

When playing a CD or SACD, press the Blue button on the remote control to activate the Shufﬂe and Random modes. Each press of the Blue button switches the playback mode in the following sequence: Shufﬂe , Random and Normal.

Note: Via USB, the 650BD can play WMA and MP3 ﬁles only. The 650BD cannot play AAC ﬁles.

In the music browser, you can perform the following operations:

Press the !" buttons or Page !"buttons to move the cursor and select music ﬁles.

When a music ﬁle is highlighted by the cursor, press the Enter or #/$button to start playback.

Press the Green colour button to add the currently highlighted music ﬁle to the Playlist. A Green check mark will appear in front of the ﬁle name, and the Playlist count in the lower left corner of the screen will increase by one.

Press the %button to move the cursor to the selection menu in the lower left corner of the screen. This menu contains the following choices:

All Music – List all music ﬁles in a ﬂat view without any directory structure.

Playlist – List only music ﬁles added to the Playlist.

Browser – List folders and music ﬁles according to the original directory

structure on the disc or USB drive.

Now Playing – Show the status of the currently playing music ﬁle. Press the # button to move the cursor back to the ﬁle listing.

If a music ﬁle starts playing and there is no other user operation, the

"Now

Playing" screen will appearafter a few seconds. You can also get to this screen using the "Now Playing" menu. This screen can show the following information:

Playback status – #/$, &

Playback mode – Shufﬂe, Random, Repeat One, Repeat All

Playback progress – Track and time

Other embedded information –If the music ﬁle contains supported

album art image and tags, those will be displayed.

650BDazur

ENGLISH

As well as normal CD’s, SACD’s, DVD’s and BD’s the 650BD can play some music, movies and photo ﬁles either from optical datadiscs (such as CD-R, DVD-R etc.) or external memory such as USB ﬂash-drives/thumbdrives and hard-drives.

Connecting a USB Drive

The 650BD is equipped with two USB 2.0 ports, one on the front panel and the other on the back. You may use either to plug in a USB drive loaded with digital music, movie and photo ﬁles.

The USB ports are rated to provide a maximum of 5V, 500mA power to the attached device. This is usually sufﬁcient to bus power (i.e. self power) USB ﬂash drives and ﬂash memory card readers, but may not be sufﬁcient for USB hard disks. It is recommended that if you use a USB hard disk you use one with an external power supply.

Note:

• This unit supports

"USB Mass Storage Class Bulk Transport" devices

only. Most USB thumbs drives, portable hard disk drives and card readers conform to this device class. Other USB devices such as MP3 players, digital cameras, and mobile phones that include their own memory management may not be compatible.

• Supported USB drives must be formatted with the FAT (File Allocation Table) or FAT32 ﬁle system. Drives formatted with NTFS ﬁle system are not supported.

• In some cases, an incompatible USB device may cause the player to stop responding. If this occurs simply turn off the power, remove the USB device, and turn the player back on.

• The player accesses the USB drive in read-only mode. In order to minimize the risk of data corruption, it is recommended that you only unplug the USB device when playback has completely stopped.

The Home Menu

When a USB drive or an optical disc stored with media ﬁles is inserted, the player presents a "Home menu" to assist you in navigating and playing the ﬁles. You can also bring up the Home menu with the button on the remote control. The Home menu is the starting point for accessing media ﬁles.

There are four selections in the Home Menu. Depending on what type of media ﬁles that you intend to play, you can choose from

"Music", "Movie"

and "Photo" categories. The "Setup Menu" selection will bring you to the player’s Setup Menu just like pressing the Setup button on the remote control.

Playing music ﬁles

To play digital music ﬁles stored on an optical disc or USB drive, select

"Music" from the Home Menu. A ﬁle browser will appear to assist you in

navigating the ﬁles and folders.

The ﬁrst step is to select the

"Data Disc" or USB device that contains the

music ﬁles. The player will take a moment to read the disc and list the folders and music ﬁles.

Other media playback

Media playback continued

The following operations are available while the "Now Playing" screen is shown:

Normal playback control – !/", #, $/%, &, and '.

Special playback mode –Repeat and Shufﬂe/Random (Blue colour

button).

Return to the Browser without stopping the music –Return

Stop playback and return to the Browser – Press # twice.

Playing movie ﬁles

To play movie ﬁles stored on an optical disc or USB drive, select "Movie" from the Home Menu. A ﬁle browser will appear to assist you in navigating the ﬁles and folders.

The ﬁrst step is to select the

"Data Disc" or USB device that contains the

movie ﬁles. The player will take a moment to read the disc and list the folders and movie ﬁles.

In the movie browser, you can perform the following operations:

1. Press the (/) or Page (/) buttons to move the cursor and select

movie ﬁles.

2. When a movie ﬁle is highlighted by the cursor, press the Enter or !/"

button to start playback.

Once a movie ﬁle starts playing, the normal playback control functions are available. To stop the movie and return to the ﬁle browser, press STOP twice. You can also press the button at any time to get back to the Home Menu.

Viewing photo ﬁles

To view digital photo ﬁles stored on an optical disc or USB drive, select

"Photo" from the Home Menu. A ﬁle browser will appear to assist you in

navigate the ﬁles and folders.

The ﬁrst step is to select the "Data Disc" or USB device that contains the photo ﬁles. The player will take a moment to read the disc and list the folders and photo ﬁles.

In the photo browser, you can perform the following operations:

• Press the (/) or Page(/) buttons to move the cursor and select photo ﬁles.

• When a photo ﬁle is highlighted by the cursor, press the Enter or !/" button to start playback in a full screen slideshow fashion.

The following operations are available during the photo slideshow:

Show the help screen – Display

Normal playback control – !/" and $%.

Adjust slideshow speed – & and '

Zoom – Zoom. Once in a zoom mode the ()*! navigational buttons

can be used to pan the photo.

Reﬂect – ( button.

Mirror – ) button.

Rotate left (counterclockwise) – * button

Rotate right (clockwise) – ! button

Repeat – Repeat button

Show photos in

"Digest" mode – Red colour button. The "Digest" mode

shows the nine photo thumbnails in a screen to make visual navigation easy.

Show EXIF information – Green colour button

Play in random/shufﬂe sequence – Blue colour button

Change slideshow transition effect – Yellow colour button.

Adding background music

You can add background music to the photo slideshow. To do so, you will need to prepare some digital music ﬁles. The music ﬁles can be stored on the same disk as the photos, or on a different USB drive. Start music playback ﬁrst by selecting "Music" from the home menu. Once the music is playing, press the button to get back to the home menu, and start the photo slideshow by selecting "Photo" in the usual manner.

650BDazur

ENGLISH

Setup Menu

To access the player’s Setup Menu simply press the Setup button on the remote control. Since some Setup Menu options can become inaccessible when the player is playing a disc, it is recommended that you operate the Setup Menu when playback is fully stopped or when there is no disc in the player.

The Setup Menu presents many setup and conﬁguration options. For most users, the default conﬁguration will be sufﬁcient and will often not require changes to the settings.

However if you wish to conﬁgure the player to perfectly match your home theatre settings and viewing preferences, please refer to the following sections for details about each conﬁguration option.

Using the Setup Menu System

When performing menu adjustments, we will use the following terminology to indicate the location of the desired function:

Setup Menu Section > Menu Item > Selection

Setup Menu Section is the uppermost Setup Menu level. With the 650BD

there are six Setup Menu sections listed in the left column of the Setup Menu screen. They are: Playback Setup, Video Setup, Audio Format Setup, Audio Processing, Device Setup, and Network Setup.

Menu Item is the parameter to be adjusted which appears in the centre column of the Setup Menu. Once you enter a Setup Menu Section, the list of Menu Items and their current value are displayed in a box.

Selection is the actual numeric or descriptive element that represents the change being made to the selected parameter. It is the item located to the right of its corresponding Menu Item.

A scroll icon appears at the top or bottom of the menu when there are more Menu Items or Selections than what can ﬁt in a screen. You may use the ! and " buttons to scroll the display in order to access additional items.

Note: It is possible that some setup items are greyed-out and inaccessible. This can be caused by a disc still being played back or interlocking with mutually exclusive setup items. Please stop playback or eject the disc before trying to change these setup items. If you still cannot access the setup item, please check for conﬁguration conﬂicts and consistency. For example, if

"Video Setup > Primary Output" is set to

"Component", the "Output Resolution" menu items "Auto" and "Source

Direct" will be grayed-out. Setting "Primary Output" to "HDMI" will enable the "Output Resolution" menu items "Auto" and "Source Direct" to be set.

1. Press the Setup button on the remote control, and the TV screen

displays the following:

2. Press the !/" buttons to select the section. There are six sections:

Playback Setup, Video Setup, Audio Format Setup, Audio Processing, Device Setup, and Network Setup. Press the Enter button or the #

button to enter the selected section.

3. Press the !/" buttons to select the setup item to be changed, and

press the Enter or # button to change the setting. When the scroll icon is shown at the top or bottom of the Setup Menu, it indicates that there are more menu items that can be accessed by scrolling with the !/" buttons.

4. To select a value from the list of available settings, press the !/"

buttons and then press the Enter button to conﬁrm. For example, to select

"Off" for "PIP Mark", use the !/" buttons to highlight the "Off"

selection and press the Enter button.

5. To exit the Setup menu at any time, press the Setup button on the

remote control or select Exit from the Setup Menu sections.

The settings are permanently saved when the player is turned off using either the front panel Standby/On button or the same button on the remote control. If the AC power is interrupted before the player enters standby status, the settings will not be saved.

Setup

+ 47 hidden pages