1.Check that the rear of the product indicates the correct supply voltage
for you area.
2. The lighting flash with the arrowhead within an equilateral
triangle is intended to alert the user or service agent to the
presence of dangerous voltages within the product enclosure
that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
3. The exclamation point within an equilateral triangle is
intended to alert the user or service agent to the presence of
important operating and maintenance (Servicing) instructions
in the literature accompanying the appliance.
4. This product complies with EEC Low Voltage (73/23/EEC) and
Electromagnetic Compatibility (89/336/EEC) Directives when used and
serviced in accordance with this manual. For continued compliance all
components marked safety and EMC critical must only be replaced by
Cambridge Audio approved parts.
5. Any unauthorised design alterations or additions will void the
manufacturer’s warranty; furthermore the manufacturer cannot accept
responsibility for personal injury or property damage resulting therefrom.
6. When servicing, care should be taken to observe the original routing
and dressing of the leads and it should be confirmed that they have been
returned to normal after re-assembly.
Notes on chip component replacement
Never reuse a component that has been removed from a PCB
Notice that the minus side of a tantalum capacitor may be damaged by heat
Cambridge Audio and Azur are registered trademarks of Audio Partnership PLC. This document
may not be reproduced, distributed, transmitted, displayed, published, or broadcast without the
express written prior permission of Audio Partnership PLC.
Alteration or removal of any trademark, copyright, or other notice from this content is prohibited.
Information provided in this document is provided solely for the use of official service agents in
repairing and servicing Audio Partnership PLC products.
Page 4
LASER SAFETY PRECAUTIONS
y
Caution: These labels may be attached to the unit on the rear and inside to
inform that it contains a laser component. Use of controls or adjustments, or
performance of procedures other than those specified within the service or
instruction manual may result in hazardous radiation exposure.
CLASS 1 LASER PRODUCT
WARNING!
1. Service should only be performed by qualified personnel.
2. This equipment has been designed and manufactured to meet
international safety standards; it is the legal responsibility of the repairer to
ensure that these safety standards are maintained.
3. Any repairs must be made in accordance with the relevant safety
standards.
4. It is essential that safety and EMC critical components are replaced with
Cambridge Audio approved parts only.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the
potential difference generated by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic breakdown and also use the procedure in the printed
matter which is included in the repair parts.
The flexible board is easily damaged and should be handled with care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concerated so as to be focused on the disc reflective surface b
the objective lens in the optical pick-up block. Therefore, when checking the laser diode
emission, observe from more than 30cm away from the objective lens.
Page 5
8
Drawing ref AP part Factory refDescription
1CA new side panel
7
6
5
4
3
2
REV
1
EDITOR
GTL
1
REVISIONS & DATE
DATE
26/11/04
2CA new plastic insert rear
2
6
15
11
5
16
4
3CA new plastic insert front
4CA new back panel
5PY5076550-010204-000-01Azur 640C Top Panel Black
F
5PY5086550-010204-000-02Azur 640C Top Panel Silver
6PY5157002-608010-001Screw M2.6 x 8 M/C Torx Recessed 1/K Head Black
REVISIONS NOTES:-
F
6PY5167002-608010-006Screw M2.6 x 8 M/C Torx Recessed 1/K Head En-Plated (silver)
1: ORIGINAL DRAWING 26/11/04.
7PY7926564-010001-000A04 Azur-340C FRONT PANEL Silver (Aluminium panel)
7PY7866564-010001-000-04Azur-340C aluminium FRONT PANEL-Black W/S Cool grey 7C
8PY7918534-001010-301Azur-340C Complete FRONT PANEL ASSY (Silver) REV A
8PY7858534-001020-301Azur-340C Complete FRONT PANEL ASSY (BLACK) REV A
14PY7046600-170104-000CA NEW RANGE AMP 7MM TAC SWITCH CUSHION
E
15PY7879434-001000-011Azur-340C MAIN BOARD ASSY (AP146471) REV A
16PY7899434-001000-531Azur-340C OUTPUT BOARD ASSY AP14647/4 REV A
17PY7889434-001000-071Azur-340C 230V POWER PCB ASSY REV A
18PY5739805-064001-000Azur-340/540/640AC REMOTE CONTROL ASSY
19PY5446600-170100-000FOOT PAD FOR Azur-640A
20PY5686564-010006-000A01 Azur-640C.Silver CD DOOR W/SILKSCREEN PMS COOL GREY 7C
20PY5546564-010006-000-01Azur-640C.Black CD DOOR W/SILKSCREEN PMS COOL GREY 7C
21PY5523110-064580-100LCD DISPLAY ISO6458P01V0 113*25.7MM NEGATIVE (BLACK UNIT)
21PY5623110-064580-000LCD DISPLAY ISO6458P00V0 113*25.7MM POSITIVE (SILVER UNIT)
22PY5569464-001000-041Azur-540C & 640C CONTROL BOARD ASSY REV A
Note:user manual is downloadable from our www.cambridge-audio.co.uk
Note: resistors, capacitors and other 'generic' electronic components are not usually
stocked by the manufacturer. Please obtain these locally.
Page 20
Cambridge Azur 340C Output PCB Assembly BOM
AP PART NO.VALUEDESCRIPTIONQTYCOMPONENT IDENT
RESISTORS
10R0.25 W Metal Film Resistor1R2
47R0.25 W Metal Film Resistor1R3
91R0.25 W Metal Film Resistor1R31
100R0.25 W Metal Film Resistor1R1
430R0.25 W Metal Film Resistor1R32
Zuznbao AV2-8,4-13EL Dual RCA connector, gold plated1CN1
Analogue O/P 3 way 2.0mm pitch JST type connector1CN2
DOUT 3 way 2.0mm pitch JST type connector1CN3
Single RCA connector, gold plated1CN4
MISCELLANEOUS
5uHInductor NKW8W2FB1, FB2
PCB
Schematic AP14644/3
AP14645/3Blank PCB1
Gerber file is AP14645/3
PCB Construction details AP14646/3
AP14647/4
Note: resistors, capacitors and other 'generic' electronic components are not usually
stocked by the manufacturer. Please obtain these locally.
Page 21
A
Cambridge Azur 340C CD Player Main Assembly BOM (Silver UK)
P DRAWING
NO
AP12735/5Bottom Panel1
AP12652/2
AP12883/3PY544Azur Foot Pad4Affix on Foot Using Adhesive Surface
AP13571/1Cambridge Audio New Range CD Transformer Pad1
AP13157/3PY563Cambridge Audio EI 115/230v 540c/640c Transformer1Position On Transformer Pad With Fixing Bolts Through Supplied Holes
AP13545/1
AP13544/3Cambridge Audio New Range CD Mech Top Sticker1
AP13495/1
AP13617/116 Way Laser Cable, Flexible Flat Cable 250mm1Connects Servo PCB To Laser Block On The CD Mech
AP13618/15 Way Tray Motor Cable Flat Wire Style 350mm1
AP13619/16 Way Spindle Motor Cable 200mm1Connects The Servo PCB To The CD Mech, Runs Under The CD Mech
AP13895/1Mains PCB Insulating Sheet1
AP12935/1IR Lens1Glued In Place On The Front Panel
AP13322/2105mm Display Window (Mirrored)1Glued In Place On The Front Panel
AP13436/2Sub Panel Left1
AP12931/1Lightguide, Cut To Single Pipe1Fasten To Subplate Left
AP13585/19mm TAC Switch Cushion1
AP11782/1Opus Control Box Button (9mm)1Position in Place on the Front Panel
AP13437/2Sub Panel Right1
AP12934/1PY7047mm TAC Switch Cushion5
AP12925/1
AP13578/3Front Panel PCB Assembly BOM1Fixes onto the Sub Panels With M3 M/C Screws
AP12725/2Pressed Side Panel (2 Ridge)2
AP12727/1
AP12728/1Rear Plastic Support (2 Ridge With Captive M2.6 Nuts)2Position at Rear within Side Panels
AP13435/2Rear Panel Printed 1Screened With Artwork AP14835/1
AP14647/2PY789Output PCB Assembly BOM1Mounted directly on the rear panel
AP13620/18 Way LCD Cable, Flat Wire Style 280mm2
AP13621/17 Way LCD Cable, Flat Wire Style 500mm1
AP13622/17 Way Control Cable 520mm1
AP13623/13 Way Standby Cable 380mm1
AP13624/12 Way Backlight Power Cable 440mm1
AP13626/13 Way Shielded Digital Out Cable2From DAC PCB to rear panel PCB assembly
AP13340/1Lidding Tape For Front And Rear Panels2Fix To The Correct Surfaces For Lid
AP13342/1Lidding Tape For Side Panels2Fix To The Correct Surfaces For Lid
AP12733/2
AP PART NODESCRIPTIONQTYNOTES
PY531 - Black
PY541 Silver
PY340
PY568 Silver
PY554 Black
PY719 Black
PY720 Silver
PY507 Black
PY508 Silver
Azur Foot Moulding4Position In Place on Bottom Panel
Position In Place On Bottom Panel With The Fixing Bolts Through
Supplied Holes
Heatshrink sleeve70mm For transformer wires
Ferrite Ring1Added to secondary wires of transformer (3 turns x 3 wires)
Cambridge Audio New Range CD Transformer Can
With Adhesive Pad Added
Yanion Version Of Sony CD Mech With Sony Laser
Block (PY790)
Cambridge Audio New Range CD Draw Front1
Front Panel Assembly
M3 X 6 Pozi Pan Stp Screw1Affixes Single Lightguide To Subplate
7mm TAC Switch Button5Position In Place On The Front Panel
Side Panel Assembly
Front Plastic Support (2 Ridge With Captive M2.6
Nuts)
M2.6 X 8 C/S Pozi Plastite8To Affix Side Panels To Plastic Inserts
Rear Panel Assembly
Final Assembly
Ferrite Tube1Fit ferrite over screened cables, CN2 & CN3 on output PCB
M2.6 X 6 Pozi Pan Machine Screw15To fix Bottom Panel To Side, Front And Rear Panels
Lidding
Top Panel Without Vents1Position on Top Of The Product
Screened With Artwork AP13721/1 Position On Top Of Transformer
1
And Press To Stick In Place
1Position In The Correct Position On The Bottom Panel
Screened With Artwork AP13763/1. Then Position Over Locating Pips
On CD Mech Top Surface And Press To Stick
Screened With Artwork AP13601/1 Position On Draw Front And Glue In
Place
Connects The Servo PCB To The CD Mech, Runs Under The Front Of
The Mech And Under The Servo PCB
Cut to fit 2 standoffs. To Be Positioned Over Standoffs Under Power
PCB
Fasten in place between the Ledges of the Front Panel, Align Up The
Power Button Holes
Position on the 9mm tact switch button, down the main shaft affix using
adhesive provided on the cushion.
Fasten in place between the Ledges of the Front Panel, Align Up The
Function Button Holes
Position on the 7mm tact switch Buttons, down the main shaft affix using
adhesive provided on the cushion.
2Position at Front within Side Panels
Connects The Front Panel PCB To The Servo PCB, Runs Around The
Side Of The Casework
Connects The Front Panel PCB To The Servo PCB, Runs Around The
Side Of The Casework
Connects The Front Panel PCB To The Servo PCB, Runs Under The CD
Mech Then Around The Outside Of The Casework
Connects The Front Panel PCB To The Stand By PCB, Runs Underneath
The CD Mech
Connects The Front Panel PCB To The Servo PCB, Runs Under The CD
Mech Then Around The Outside Of The Casework
AP15162/2
Note: resistors, capacitors and other 'generic' electronic components are not usually stocked by the
manufacturer. Please obtain these locally.
Page 22
A
Cambridge Azur 340C CD Player Main Assembly BOM (Silver UK)
P DRAWING
NO
AP13612/1Azur 2 Ridge Woven Bag1Pack CD Player Unit Inside
AP13504/2Poly Endcap Packaging2
AP13613/1Azur Woven Bag For Remote Control1Pack Remote Control Inside,
AP15161/1340C CD Player Instruction Manual1
AP13505/1Carton Packaging With Handle1Printed To Artwork AP13716/1
AP14702/1Carton Label (Model No.) 1For Box
AP PART NODESCRIPTIONQTYNOTES
PY515 Black
PY516 Silver
PY573
M2.6 X 6 C/S Torx Machine Screw8To Affix Top Panel to plastic Inserts, Side, Rear and Front Panel
Packaging
Azur Remote Control Complete. Model No RC540AC/640AC
AAA Alkaline Batteries3For Remote. Place In Instruction Manual Polybag
Polybag 173X260X4C mm1For Instruction Manual and Remote Batteries
1830mm AC IEC Power Cord Set BS Standard Fused 3
AMP
Blue Tape Seal For Cambridge Carton1
1Mounted into Poly Endcap, Packing in Rebate Provided
1Must Be Bs Approved
AP15162/2
Note: resistors, capacitors and other 'generic' electronic components are not usually stocked by the
manufacturer. Please obtain these locally.
Page 23
Cambridge Azur 340C CD Servo PCB Assembly BOM
AP PART NO.VALUEDESCRIPTIONQTYCOMPONENT IDENT
RESISTORS
10R0.125 W Metal Film Resistor1R62
10R0.25 W Metal Film Resistor1R40
27R1 W Carbon Resistor1R67
47R0.125 W Metal Film Resistor3R10, R68, R69
100R0.125 W Metal Film Resistor1R58, R87
120R0.5W Metal Film Resistor1R83
220R0.125 W Metal Film Resistor1R4
390R0.125W Metal Film Resistor1R90
470R0.125 W Metal Film Resistor2 R33, R34
560R0.125W Metal Film Resistor1R85
1k0.125 W Metal Film Resistor6R3,R20,R21,R25,R60,R88
2k20.125 W Metal Film Resistor2R1, R66
3k30.125 W Metal Film Resistor7R19, R41, R42, R43, R45, R46, R47
3k90.125W Metal Film Resistor1R86
4k70.125 W Metal Film Resistor3R32, R76,R84
5k10.125 W Metal Film Resistor4 R53, R54, R55, R56
R8, R11, R12, R13, R14, R15, R16, R17, R18,
10k0.125 W Metal Film Resistor21
12k0.125 W Metal Film Resistor2R74, R80
15k0.125 W Metal Film Resistor6R2, R5, R72, R75, R79, R82
33k0.125 W Metal Film Resistor2R52, R57
47k0.125 W Metal Film Resistor10
68k0.125 W Metal Film Resistor1R7
82k0.125 W Metal Film Resistor1R59
100k0.125 W Metal Film Resistor1R63
220k0.125 W Metal Film Resistor1R6
330k0.125 W Metal Film Resistor1R89