LTR20091033, Rev. A
12/16/08
Assembly ........................1
Tools and Materials ....................1
Step Assembly ........................1
Planter Assembly......................5
Bar Stool Assembly ....................6
Bar Assembly and Installation ...........7
Bench Assembly......................13
Panel Assembly ......................15
Maintenance ....................17
Warranty Information.............18
Read This First!
Carefully read and follow all safety instructions.
When installing and assembling your surround
package, it is recommended that two or more
people be involved.
Do not use the unit during an electrical storm.
Do not climb on top of the surround package. While
the surround package is made out of high-quality
material and is extremely durable, it is not meant
to support weight. In addition, falling off of the
surround package while climbing on it can result in
serious injury or death.
Do not attempt any repair without consulting the
manufacturer rst. Unauthorized repairs will void
the manufacturer’s warranty (within the rst 90
days).
Copyright 2008-2009 LMS, Inc. All rights reserved. Duplication without
written consent is strictly prohibited.
Cal Spas™ and Cal Enclosures™ are registered trademarks.
Due to continuous improvement programs, all models, operation, and/or
specications are subject to change without prior notice.
LTR20091033, Rev. A
12/16/08
CONTACT INFORMATION
For customer service, please contact
your authorized dealer immediately. If
you need additional information and/
or assistance, please contact:
LMS Customer Service Department
1462 East Ninth Street
Pomona, CA 91766.
Toll Free: 1-800-CAL-SPAS
Fax: 1-909-629-3890
www. c a l s p as. c o m
Assembly
Whether you assemble your surround package yourself or hire someone to do it, your new surround package
needs to be assembled in a specic order. Our Cal Enclosures professionals have determined through their
experience that this is the easiest way to assemble your surround package.
Tools and Materials
Utility knife 25’ tape measure Cordless drill
100’ extension cord Electric drill Phillips-head drill tips
1/8” pilot hole drill bit 9/16” socket Slotted-head drill tips
Sandpaper (various grades) Redwood stain Wood putty
Gray wash stain Rags 1/2” ratchet and impact drill
1/2” carbide drill bit (masonry bit)
Step Assembly
Two Tier, 30” Step
Stand the legs up at 30” apart. Place the upper step on top of the upper section of the step.1.
To attach the step, screw in 4 screws (2 at each rear corner): 1 into the step leg and 1 into the step itself.2.
Place the lower step on the lower section of the step.3.
1
Assembly
To attach the step, screw in 4 screws (2 on each on the outside of the step). Use the toe-in method on both 4.
sides, as shown.
2009 Spa Surrounds
LTR20091033, Rev. A
www. c a l s p as. c o m
2
Package R Step Assembly
Assembly
2009 Spa Surrounds
LTR20091033, Rev. A
www. c a l s p as. c o m
3
Package D, E, and I Step Assembly
Assembly
2009 Spa Surrounds
LTR20091033, Rev. A
www. c a l s p as. c o m
4
Cal Select Step Assembly
Assembly
2009 Spa Surrounds
LTR20091033, Rev. A
www. c a l s p as. c o m
Planter Assembly
5
Assembly
2009 Spa Surrounds
LTR20091033, Rev. A
www. c a l s p as. c o m
6
Bar Stool Assembly
Attach the bar stool legs to support the brace using the provided 2 ½” screws. There will be a total of 12 1.
screws.
Assembly
Place the bar stool seat on a at surface. (Make sure the nish side is on the ground.) Attach the leg 2.
assembly using four 2 ½” screws.
2009 Spa Surrounds
LTR20091033, Rev. A
www. c a l s p as. c o m
Bar Assembly and Installation
Package B and M
7
Assembly
2009 Spa Surrounds
LTR20091033, Rev. A
www. c a l s p as. c o m
8
Package C, J, and N
Assembly
2009 Spa Surrounds
LTR20091033, Rev. A
Assembly
www. c a l s p as. c o m
9
2009 Spa Surrounds
LTR20091033, Rev. A
www. c a l s p as. c o m
10
Assembly
Package P and G
NOTE: The manufacturer recommends mounting corbels on the cabinet so that the bar top sits just under the
spa lip.
Using 2 1/2” screws, mount the corbels directly to the cabinet wall. Make sure that the corbels are horizontally 1.
level with each other.
Mount the bar top to the corbels with the 2 1/2” screws. The screws must be mounted from the underside 2.
of the bar top. Make sure that the bar top rests just below the lip of the spa.
2009 Spa Surrounds
LTR20091033, Rev. A
www. c a l s p as. c o m
11
Assembly
2009 Spa Surrounds
LTR20091033, Rev. A
www. c a l s p as. c o m
12
Package R
Assembly
2009 Spa Surrounds
LTR20091033, Rev. A
www. c a l s p as. c o m
Bench Assembly
Package P and G
13
Assembly
2009 Spa Surrounds
LTR20091033, Rev. A
www. c a l s p as. c o m
14
Package R
Assembly
2009 Spa Surrounds
LTR20091033, Rev. A
www. c a l s p as. c o m
Panel Assembly
Package I
15
Assembly
2009 Spa Surrounds
LTR20091033, Rev. A
www. c a l s p as. c o m
16
Package J
Assembly
2009 Spa Surrounds
LTR20091033, Rev. A
www. c a l s p as. c o m
Maintenance
Your surround package was designed with low cleaning and maintenance in mind. We recommend that the
surround package be cleaned at least twice a month (or more, if needed). When cleaning your surround
package, do not use cleaning solvents -- using a sponge and water will be ne. For ground-in dirt and grime,
refer to the following section.
Maintaining your surround package is an easy task. We recommend that every six months you inspect your
surround package.
If your surround package is redwood, take note of any deformities in the wood (i.e. cracking, peeling, dirt,
grime, etc.). Wipe the stained area clean and reapply until the sanded area matches the rest of the surround
package.
If your surround package is Cal Select, wipe off any dirt or grime using a sponge and water. Condition the Cal
Select with Cal Spas Vinyl Cleaner and Conditioner. Follow directions on label.
17
Maintenance
2009 Spa Surrounds
LTR20091033, Rev. A
Warranty Information
See your Cal Enclosures surround package dealer for a copy of the applicable warranty, details and any questions
you may have regarding the warranty coverage on your surround package.
Warranty Limitations
The Limited Warranty is void if the surround package has been subject to negligence, alteration, misuse, abuse,
repairs by non-LMS authorized representatives, acts of God and any other cases beyond the control of LMS.
Examples of common acts invalidating this warranty include but are not limited to:
Use of the surround package in a non-residential application•
Scratches caused by normal use•
Damage caused by extreme weather conditions (heat, cold, etc.)•
Damage caused by dirt, sand, and/or water damage•
Damage caused by direct sunlight•
Damage caused as a result of failure to follow the assembly instructions as dened in this Owner’s Manual•
This Limited Warranty applies only to surround packages normally used for personal, family, or household
purposes.
This Limited Warranty is obsolete 90 days after the original purchase date.
Warranty Exclusions
LMS warranties the surround package from defects in material and workmanship for a period of 90 days from the
original date of purchase.
DON’T FORGET TO REGISTER YOUR NEW PRODUCT AT WWW. CALSPAS.COM.
Customer Service
For customer service, contact the authorized selling dealer immediately. If you need additional information and
assistance, please contact the LMS Customer Relations Department at 1462 East Ninth Street, Pomona, CA 91766,
or call 909-623-8781.
Spa Surround Model: ___________________________________________________________________
Spa Surround Serial Number: ____________________________________________________________
Date Purchased: _______________________________________________________________________
Date Installed: ________________________________________________________________________
Cal Spa Dealer’s Phone Number: __________________________________________________________
Cal Spa Dealer’s Address: _______________________________________________________________
Loading...