Calomax eclipse 3C5, eclipse 3W5, eclipse 3C10 Installation, Operation And Servicing Instructions

MODELS:

3C5, 3C10 & 3W5

INSTALLATION, OPERATION AND SERVICING INSTRUCTIONS

FOR THE ECLIPSE RANGE OF WATER BOILERS

Please read these
instructions carefully
before operating your
boiler for the fi rst time

Issue 2

026/07/10

DCR :810

Calomax Limited

Lupton Avenue, Leeds LS9 7DD

Tel. [phone] Fax. [phone]

e-mail: [e-mail] www.calomax.co.uk

Page 2

Page 3

CONTENTS

INTRODUCTION 3

CHECK LIST 3

APPROVALS 3

CONSTRUCTION 4

INSTALLATION 4

LOCATION 4

COLD WATER INLET 5

DIMENSIONS AND WEIGHTS 6

VENT / OVERFLOW 7

ELECTRICAL CONNECTIONS 8

USER INSTRUCTIONS 8

SCALE 9

GENERAL OPERATION 9

CLEANING 9

TROUBLE SHOOTING 10

ACCESSORIES 11

SPARE PARTS 12/13

EXPLODED DIAGRAM 14/15/16/17

SERVICE INSTRUCTIONS 18/19

GENERAL FUNCTION 20

WIRING DIAGRAM 21

SERVICE HISTORY NOTES 22

WARRANTY 23

PRODUCT SPECIFICATION 24

INTRODUCTION

Thank you for purchasing a boiler from the Calomax Eclipse range.
All our products are designed to give years of simple, reliable
operation. To ensure this, it is important that the installation and
subsequent servicing and maintenance is carried out by a suitably
qualifi ed engineer in accordance with these instructions. For
assistance in fi nding a suitable engineer in your area, visit our
website www.calomax.co.uk, contact our service department on
0113 249 6681 or e-mail: [e-mail]

CHECK LIST counter top models

Before commencing installation, check that the following parts have
been supplied with the boiler:

1. Wall mounting bracket

This product conforms to the CE marking directive 93/68/EEC
through compliance with the following standards:

Electromagnetic Compatibility Directive
Low Voltage Directive 73/23/EEC in accordance with:
BS EN 60335-2-75:2004. Compliance with these standards
has been confi rmed through testing by an independent NAMAS
approved body

APPROVALS

PAGE

CHECK LIST wall mounted models

Before commencing installation, check that the following parts have
been supplied with the boiler:

1. WRAS approved fl exible water inlet hose suitable for
potable water.

2. Drip tray kit

The tap handle and drip tray (part ref: MDTBK
where supplied) have been treated with Steritouch
additive and independently tested to prove
the effectiveness of the surface hygiene.

Page 4

Page 5

LOCATION

COLD WATER INLET

INSTALLATION AND MAINTENANCE

All metallic components of the machine, in direct contact with
drinking water are manufactured from high quality 304 grade
stainless steel, or non ferrous materials, providing maximum
resistance to corrosion.

CONSTRUCTION

To comply with recommendations
from the Health and Safety Executive
it is important that due consideration
be given to safe operation of the
controls of the boiler. The boiler should
therefore be mounted in such a manner
that the operator can stand directly
facing the machine with the controls at
a recommended height from the fl oor to
the draw-off tap handle of 1200mm +/-

100mm. Consideration should also be

The boiler must be installed in a location where access is

restricted to operators that are suitably trained, or where
untrained operators of the machine can be supervised by trained
personnel.

Calomax products have been tested and found to comply
with the requirements of the Water Supply (Water Fittings)
Regulations 1999 for England and Wales Water Bylaws
2000, Scotland and the Water Regulations Ireland.

given to the servicing requirements of the machine. The maximum
and minimum ambient operating conditions must be between
5 °C and 35 °C. The appliance is not suitable for installation where
a water jet could be used. Install the boiler on a surface or wall
suitable for the working weight of the boiler. Allow clearance for
ventilation and for the easy removal of the outer casing lid and

front panel. Calomax ltd recommend a minimum clearance of
50mm on all sides of the boiler. A suitably qualifi ed engineer must
install this unit. Plumbing and electrical installation work may be
involved.

To comply with the U.K. Water Supply Regulation a single check­valve must be fi tted to the supply. BEFORE CONNECTING, THE

SUPPLY PIPE MUST BE THOROUGHLY FLUSHED OUT TO
ENSURE THAT FOREIGN MATTER DOES NOT BLOCK OR
ENTER THE SOLENOID VALVE

The boiler must be connected to a potable water supply using

the food grade hose where provided, or rigid 15mm pipe in
a manner which complies with UK water regulations via an
appropriate isolating valve. The supply must provide a constant
pressure of between 20 KPa and 1000 KPa (0.2 to 10 Bar).
If the water supply contains excessive solids in suspension it is
recommended that a fi ne mesh “in line” water fi lter is fi tted in the
pipe work. Failures due to scale and sediment are not covered by
the warranty.

p PP

3 point fi xing wall
bracket for wall
mounted range

Hang the boiler on the wall bracket and secure into place with
4th fi xing. The electrical cable should be routed as shown

Cold water
inlet

Vent &
overfl ow

Applied for

Page 6

Page 7

VENT & OVERFLOW

The vent / overfl ow pipe must be extended and laid with a

continuous

fall,

discharging to a safe and visible point. The pipe should not be
directly connected to a closed waste, as taste problems may occur and
should never be allowed to become blocked or restricted.15mm copper or
‘Speedfi t’ pipe should be used. The drip tray kit provided with the counter
top models allow the option of plumbing the overfl ow pipe to discharge
into the drip tray and then plumbing the drip tray to a safe and visible
point of discharge. If the machine is operated without the overfi ll pipe
being extended as advised, any subsequent damage incurred will be the
responsibility of the installer.

DIMENSIONS AND WEIGHTS

3C5 3C10

Height 570mm 570mm

Depth 260mm 355mm

Width 240mm 240mm

Drip tray clearance 175mm 175mm

Working weight 21 Kg 30.5 Kg

3W5

Height 510mm

Depth 250mm

Width 315mm

Working weight 21 Kg

If the boiler is required to

drip or overfl ow into the
drip tray, the confi guration
of pipework may be altered
as follows. Remove the
machine front panel and
unclip the pipework elbow.
Carefully pull the elbow
in the direction of the
arrow, out of the silicone
connecting tube on the
end of the main water pipe.
The silicone connecting
tube will now direct water
into the drip tray.