California Faucets Single Hole/Handle Bidet Faucet User Manual

Tel: [phone]

Ref. 6204-INSTL

(V 01) 02/28/06

Continued

Fax: [phone]
Toll Free: 800-822-8855

www.calfaucets.com

SINGLE HOLE-SINGLE HANDLE BIDET FAUCET

6204

INSTALLATION
INSTRUCTIONS

IMPORTANT

All California Faucets products are engineered to provide quality performance provided they

R

are installed and operated properly. To fully enjoy the comfort, safety, and reliability of your new
Single Hole-Single Handle Bidet Faucet, please follow the instructions below.

California Faucets reserves the right to make modification and specification changes at any time.

Please visit www.calfaucets.com for most current technical data.

Fig. 1

Lever

Spout

Swivel
Aerator

Body

Base Ring

Two Components

Front View

Meets A112.18.1 (Min. 2.4 gpm)

***NOTE: SHUT OFF WATER SUPPLY BEFORE BEGINNING INSTALLATION***

Handle

Side View

Lift Knob

Recommended
Hole Size:
1 3/8"

1

Install flex lines: Position base ring/sealing washer:

-Screw flex lines into body,

Body

(one long & one short)
tighten with adjustable
wrench until stop. Do not
over tighten.

2

-Make sure sealing washer
is fitted into body base ring.

-Place bidet faucet base ring over
hole in bidet/top, with
sealing washer face down
and center.

Flex Lines
(one long &
one short)

Fig. 2

43

Insert lift knob/lift rod:

-Insert lift knob/lift rod into
slot at back of bidet faucet
body.

Body

Lift Knob

Install assembly:

-Place bidet faucet body assembly
on faucet base ring, inserting
flex lines, mounting rods and lift
rod through hole in bidet
top.

-Center bidet faucet on hole.

Lift Rod

Faucet Bidet/top
Hole

Faucet Bidet/top
Hole

Flex Lines

Base Ring

Fig. 3

Sealing
Washer

Mounting
Rods

Lift
Rod

Base
Ring

Fig. 4

Fig. 5

5

Install washers:

-Install rubber washer
and horseshoe washer.

6

Tighten to surface:

-Screw on 2 brass nuts to
mounting rods.

-Hand tighten as you align
Bidet faucet.

-Firmly tighten nuts with a
deep socket or adjustable

Rubber Washer

Horseshoe Bracket

wrench.

Fig. 6

7

Install pop-up assembly.

-Separate drain collar from pop-up assembly.

-Apply silicon caulking to underside of drain collar. NOTE: Do not use

"Plumbers Putty" or any oil based sealants! Use of anything other than
silicon caulking will VOID the finish warranty.

-Insert drain body from underside through sink. Slowly screw on drain
collar, align with ball rod hole facing back wall, then gently pull down into
sink and firmly tighten brass nut from below.

-Remove tailpiece from drain body and apply teflon tape, approx. 3 to
5 wraps around threads and reinstall into bottom of drain body.

-Insert stopper in collar and hold with eye-screw hole facing back.
If necessary, adjust stopper eye-screw height by loosening lock nut and
rotating counter-clockwise. Tighten lock nut (See Fig. 9).

-Remove spring clip from ball rod.

-Remove nut and cone washers and slide onto end of ball rod.

-Insert ball rod into drain body below so short end of ball rod end fits

Lock
Nut

in stopper eye-screw hole. Snug ball rod nut (do not over tighten).
Ball rod must move up & down freely (See Fig. 9).

-Insert lift rod through top of spout and then through hole rod strap

Adjustable
Eye-Screw

underneath sink. Tighten thumb-screw of hole rod strap
against lift rod and connect to ball rod by gently pinching locking
spring clip and sliding one side of spring clip onto ball rod.

-Insert hole strap onto ball rod, then pinch spring clip together to fit
on ball rod.

Nut

Fig. 9

Fig. 7

Stopper

Adjustable
Eye-Screw

Rubber
Washer

Fiber
Washers

Brass
Nut

Ball
Rod

Drain
Collar

Drain
Rim

Ball
Rod

Drain
Tailpiece

Lift Knob

Lift
Rod

Hole Rod
Strap

Nut

Cone
Washers

Fig. 8

Brass
Nuts

Mounting
Rods

Spring
Clip

8

Connect flex lines to water supply:

Flex
Line

-Connect flex lines to your
angle stops.

IMPORTANT: Remove aerator, open
hot/cold water supplies to flush faucet bidet
and replace aerator prior to using faucet bidet.
Debris remaining in the line will
damage lavatory bodies and cause leaking.
Failure to flush the lines could result in
voiding the warranty.

NOTE: Due to sediment in the water it may

be necessary on occasion to remove the aerator

and clean the screen with a soft bristle toothbrush.

Angle Stop
(not supplied)

9

Install "P" trap:

-Connect your waste "P"
trap to the drain tail piece.

Fig. 8

NOTE:

P-trap and angle stops are not supplied.

We recommend genuine

Cal-Trim parts available at your authorized

California Faucets dealer.

IMPORTANT CLEANING NOTICE

Please refer to Finish Care Instructions for complete

cleaning information. Wipe frequently with a soft, damp

cloth. Never use acids, harsh abrasives or detergents .

Drain Tail piece

"P" Trap
(not supplied)

Fig. 9