California Faucets 4 Centerset Faucets User Manual

Tel: [phone]

(V 01) 08/17/06

Continued

Fax: [phone]
Toll Free: 800-822-8855

www.calfaucets.com

4" CENTERSET

INSTALLATION
INSTRUCTIONS

All products are engineered to provide quality performance provided

R

they are installed and operated properly. To fully enjoy the comfort, safety, and reliability of your
new Centerset, please follow the instructions below.

IMPORTANT

California Faucets reserves the right to make modification and specification changes at any time.

Please visit www.calfaucets.com for most current technical data.

J Style Spout Traditional Centerset

Base

Set
Screws (x2)

Spout

Threaded
Shank

Wing
Nut

Fig. 1B

All 4" Centersets faucets meet A112.18.1 - 2.2gpm/8.31 L/min.

***NOTE: SHUT OFF WATER SUPPLY BEFORE BEGINNING INSTALLATION***

Fig. 2

Stopper

Adjustable
Eye-Screw

Rubber
Washer

Brass
Nut

Drain
Tailpiece

Lock
Nut

Adjustable
Eye-Screw

Lift
Knob

NOTE: Handles
not shown Base

Wing
Nut

Drain
Collar

Drain
Rim

Ball
Rod

Hole
Rod
Strap

Nut

Cone
Washers

Fig. 3

Ball
Rod

Nut

Lift
Rod

Spring
Clip

Handle

Fig. 1A

1 Install faucet:

-Remove wing nuts from threaded shanks and insert faucet
through holes in sink or countertop. Re-attach the two
plastic wing nuts, align faucet, and tighten firmly from below.

2 Install Handles:

-Attach the handles to the body by tightening the set
screws using the allen wrench (provided).

3

Install pop-up assembly.

-Separate drain collar from pop-up assembly.

-Apply silicon caulking to underside of drain collar. NOTE: Do not use

"Plumbers Putty" or any oil based sealants! Use of anything other than
silicon caulking will VOID the finish warranty.

-Insert drain body from underside through sink. Slowly screw on drain
collar, align with ball rod hole facing back wall, then gently pull down into
sink and firmly tighten brass nut from below.

-Remove tailpiece from drain body and apply teflon tape, approx. 3 to
5 wraps around threads and reinstall into bottom of drain body.

-Insert stopper in collar and hold with eye-screw hole facing back.
If necessary, adjust stopper eye-screw height by loosening lock nut and
rotating counter-clockwise. Tighten lock nut (See Fig. 3).

-Remove spring clip from ball rod.

-Remove nut and cone washers and slide onto end of ball rod.

-Insert ball rod into drain body below so short end of ball rod end fits
in stopper eye-screw hole. Snug ball rod nut (do not over tighten).
Ball rod must move up & down freely (See Fig. 3).

-Insert lift rod through top of spout and then through hole rod strap
underneath sink. Tighten thumb-screw of hole rod strap
against lift rod and connect to ball rod by gently pinching locking
spring clip and sliding one side of spring clip onto ball rod.

-Insert hole strap onto ball rod, then pinch spring clip together to fit
on ball rod.

4 Connect faucet to water supply:

IMPORTANT: Flush supply lines of all debris prior to

connecting to lavatory valve bodies. Debris remaining
in the line will damage valve bodies and cause leaking.
Failure to flush the lines could result in voiding the warranty.

-Connect supply risers from the angle stops.

Threaded
Shank

Wing
Nut

Supply Riser
(not supplied)

Angle Stop
(not supplied)

5 Install "P" trap:

-Connect your waste "P" trap
to the drain tail piece.

NOTE:

P-trap, angle stops, and supply risers

are not supplied. We recommend genuine

Cal-Trim parts available at your authorized

R

dealer.

Drain
Tail piece

"P" Trap

Fig. 4

Fig. 5

IMPORTANT CLEANING NOTICE

Please refer to Finish Care Instructions for complete

cleaning information. Wipe frequently with a soft, damp

cloth. Never use acids, harsh abrasives or detergents .