Califone 1005AV User manual

1005AV Record player

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE

WARNING:

TO RAIN OR MOISTURE. DO NOT REMOVE COVER. PILOT LAMPS SOLDERED IN

PLACE. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION!

RISK OF ELECTRIC SHOCK

DO NOT OPEN

SPECIFICATIONS:

Power Output: 5W
Power Consumption: 12W
Power Source: A/C adapter
Input: AC120V~60Hz
Output: DC12V~1A
Speaker Ohm: 4 Ohm /5W
Speaker Size: 4”
Speaker Quantity: 2 pcs
Speaker: 3” x 5” Dynamic Type x 2
Speed: 331/3 /45 /78 RPM

NOTE: DESIGN AND SPECIFICATION SUBJECT TO CHANGE WITHOUT NOTICE.

TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE

CAUTION:

COVER OR BACK. NO USER  SERVICEABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED PERSONNEL.

The lighting ash with Arrowhead symbol, within an

equilateral triangle, is intended to alert user to the presence
of uninsulated “dangerous voltage” within the products
ensure that may be of sucient magnitude to constitute
risk of electric shock to persons.

The exclamation point within the equilateral triangle is
intended to alert user to the presence of important
operating and maintenance (servicing) instruction in the
literature accompanying the appliance.

Califone International Inc.

1145 Arroyo Avenue, # A • San Fernando, CA 91340 USA

Toll Free 800-722-0500

International Customers call 818-407-2400 or Fax [phone]

califone.com

1005AV

INSTRUCTION MANUAL

1005AV Record player

POWER SOURCE:

Unwind the A/C power adapter (located in the adapter compartment on back
of the unit). Connect the small end of the adapter to the back of the turntable,
then the other end to power outlet.

UNPACKING THE TURNTABLE:

1. Carefully remove unit from it’s package and take it out of the plastic bag.

2. Open lid, remove black tie-wrap by untwisting and gently sliding out
from under tone arm.

3. Remove cardboard shipper.

4. Slightly lift up the needle protector below the needle.

5. Using your ngers, release the two large chrome security screws located on
both side turntable platform (2). Do not force it. This allows turntable to oat
on its shock absorbers.

6. Release tone arm hold down clip by gently pushing to the right. This will
unlock tone its arm rest.

LOCATION OF PARTS

1. ADAPTOR FOR 45 rpm RECORDS

2. PLATTER

3. CENTER SPINDLE

4. TONE ARM

5. TONE ARM REST

6. CUE LEVER

7. SPEED SELECT SWITCH

8. SECURITY SCREW

9. ADAPTER JACK

10. ADAPTER COMPARTMENT

11. TONE CONTROL

12. ON/OFF VOLUME KNOB

Note: Remember to lock the hold down clip(5) and 2 chrome security
screws (8) before the unit to another location.

TURNTABLE OPERATION

1. Turn the unit on by turning the ON/OFF VOLUME(12) knob clockwise.

2. Set SPEED CONTROL switch(7) to desired speed (33, 45 or 78 rpm).
It located near cue lever.

3. Place a record on the turntable.

4. Use CUE LEVER (6) to raise the tone arm. Move the tone arm by hand out
over the and slowly lower it using the cue lever. Readjust the volume to
desires level by turning ON/OFF VOLUME (12) knob.

5. At the end of the record, the tone arm will automatically return to its arm rest.

6. Use the TONE control (11) to adjust the sound quality.

ACCESSORIES

ADAPTER FOR 45 RPM

To play the 45 rpm record, place the ADAPTOR (1) on the SPINDLE (3).

NEEDLE

Part# 007-1005-00

TROUBLESHOOTING GUIDE

The unit will not operate, try the following tips:

1. Check the unit is properly connected
to an A/C outlet.

2. Make certain that the small end of the
adapter is plugged into the power