Calibre UK DL/H, SL/H, DL-P/H, SL-P/H Installation Instructions Manual
Warning LED(s)
1. Consult with vehicle owner about LED location. For best visibility, choose a mounting location as close to the vehicle gauges
as possible.
2. Check for proper clearance behind the area where the LED(s)
will be installed (approximately 1”) and drill a 3/16” hole in the
chosen location for the LED(s). CALIBRE
DL/H
models require
the mounting of a second LED for rear radar warnings.
3. Route all of the LED wires under the dash per DIAGRAM A1.
FRONT
ALERT
REAR
ALERT
GREY LED WIRE
GREY LED WIRE
The included CALIBRE Remote Control is used to allow the driver to adjust settings on the
CALIBRE and to mute audio alerts during prolonged encounters. It may be mounted virtually
anywhere inside the vehicle with the included double stick tape or remain unmounted.
DIAGRAM A1
&
Warning Pod(s)
1. Consult with vehicle owner about Pod location. For best visibility,
choose a mounting location as close to the vehicle gauges as
possible.
2. Before mounting the Warning Pod(s), clean both the Pod surface
and desired mounting location on the dash with isopropyl alcohol.
3. Position the Warning Pod(s) on the dash with the provided double
stick “O” ring tape. CALIBRE
DL-P/H
models require the mount-
ing of a second Pod for rear radar warnings.
4. Route the black cable(s) from the Warning Pod(s) through or under
the dash per DIAGRAM B1.
DIAGRAM B1
FRONT
WARNING POD
REAR
WARNING POD
WHITE
GREY
BLUE
GREY
&
1. Remove the under dash
panel and mount the Interior
Network Module using the
supplied cable ties to the
existing factory wire looms,
brackets, or other support
structures as per DIAGRAM
C1. The Interior Network
Module can be mounted
horizontally or vertically
under the dash.
2. Connect the LED, ignitionon, and ground wires per the
separate enclosed block
diagram sheet.
HORIZONTAL MOUNT VERTICAL MOUNT
INTERIOR NETWORK
MODULE
WIRE TIE
WIRE TIES
WIRE TIE
DIAGRAM C1
INTERIOR NETWORK
MODULE
Interior Network Module
WHITE LED
WIRE
BLUE LED
WIRE
“O” RING
TAPE
“O” RING
TAPE
DL/SL HARDWIRE SERIES
DL/SL HARDWIRE SERIES
Installation Instructions
& Recommended Procedures
Amplified Speaker
1. Route the amplified speaker cable around a panel
edge and reattach the under dash panel per
DIAGRAM D1.
2. For maximum audio output and concealment,
mount the amplified speaker to the outside of the
under dash panel with the supplied screws per
DIAGRAM D1.
DIAGRAM D1
DASH PANEL
SPEAKER
SCREWS
SPEAKER
CABLE
If the vehicle is not equipped with an under
dash panel (e.g., Porsche), mount the amplified speaker to existing factory wire looms,
brackets, or support structures with the
supplied cable ties.
NOTE:
FRONT RADAR RECEIVER
(ALL MODELS)
All radar receivers can be mounted behind plastic, rubber, or fiberglass up to 1/4” thick. Do
not mount receivers behind metal, carbon fiber, or chromed plastic.
NOTE:
1. Choose a mounting location in the front of the vehicle that is not obstructed by any metal, carbon fiber, or
chromed plastic. The radar receiver must be mounted horizontally with the arrows pointing forward, towards
the road ahead.
2. Mount the radar receiver to the vehicle's structure using the supplied screws or wire tires (see diagram E1).
3. Connect the radar receiver to the 10’ black radar receiver cable. Align slot on cable plug to the notch on
radar receiver socket, slide the locking ring forward over the socket, and turn ring clockwise 1/4 turn to
engage safety lock (see diagram E2).
4. Route and affix the radar receiver cable along the inner fender in the engine compartment to the firewall
using the provided wire straps.
5. Route the radar receiver cable through a factory rubber grommet on the firewall and into the passenger
compartment (see diagram E3). Connect wires according to the separately enclosed block wiring diagram.
DIAGRAM E1
DIAGRAM E2
DIAGRAM E3
RADAR
RECEIVER
SELFTAPPING
SCREWS
FACTORY
GROMMET
FRONT
RADAR
RECEIVER
CABLE
WHITE
GREEN
BROWN
LOCKING RIB
LOCKING
WINDOW
LOCKING
PIN
LOCKING
RING
KEY
GUIDE
KEY WAY
LOCKING
PIN
Loading...