CalDigit S2VR Duo Quick Installation
S2VR Duo Quick Installation Sheet
Thank you for choosing CalDigit. This
quick installation sheet is for reference
only. Please check the detailed manual on
the provided CD, and also check our
website at www.caldigit.com
for updated
drivers/software.
1. Product Specification:
Physical Dimensions: 9.76" L X 5.12" W X 4.26" H
Power: 100-240V auto switch
Operating temperature: 0-40 degrees C or 32° to
Weight (net): 7.5lb / 3.4kg
/ 247.87mm L X 130mm W
X 108mm H
50~64Hz 1.5A, Output 5V
4.2A, 12V 3A
104°F
2. System Requirements:
• PC or Mac with an available PCI-e or PCIX slot 500 Mhz or faster**
• CD-ROM Drive
• 1GB of RAM minimum
• Mac OS 10.4 or higher
Windows 2000/XP or higher
•
**Note: You may be able to install the S2VR
into an older Mac or PC, however the overall
performance will be slower than with newer
systems. For uncompressed HD video editing,
we recommend a Dual Core G5 or higher with
1Ghz machine running with 1GB of RAM or
better.
The information of the products in this manual is subjected to change without prior
notice and does not represent a commitment on the part of the vendor, who assumes
no liability or responsibility for any errors that may appear in this manual.
S2VR Duo S2VR HD, S2VR Pro, CalDigit name and logo are registered trademarks of
Copyright © 2006, CalDigit, Inc. All rights reserved
CalDigit Inc. All other trademarks are the property of their respective holders.
3. Package Contents
• S2VR Duo
• 2 Hard drives in tray module
• FASTA-4e HBA or FASTA-4x HBA
depending on model. (Host Card)
• e-SATA Cable
• Quick Installation sheet
• Driver CD & Manual
• Power Cord
4. S2VR Interface:
5. Host Card Installation:
1. Turn off your computer and unplug the
power cord
2. Remove the cover of your computer case
and locate an available PCI-Express / PCIX slot on your motherboard.
3. Install the card into the open PCI slot on
the motherboard and make sure the card
is firmly plugged into the slot.
4. Re-install the cover of your computer case
6. Host Card Driver Installation:
5. Insert CD in CD-ROM drive.
6. Open CD, then open file CalDigit FASTA-4
v1.4.1.pkg by double clicking on it
7. Introduction Screen, CLICK Continue
8. Select OS hard drive as the Destination.
9. Finishing Installation, CLICK Continue.
10. Verify System Profiler
7. Install S2VR Manager:
1. Double CLICK the application on the
provided CD, CalDigit S2VR v1.0.1.pkg.
2. Introduction Screen, CLICK Continue.
3. Select OS hard drive as the Destination.
4. Installation Successful, CLICK Close.
5. Directory:
> CalDigit S2VR > S2VR Manager
OS drive > Applications > Utilities
6. Drag S2VR to the Launcher.
8. Configuring S2VR Manager:
• S2VR Manager limits configuration access with
a password prompt. (Default: admin)
• Go to “Management Tab” setup password,
Voice & E-mail notification.
• New password must be 5 or more characters.
• Click the “Enable Voice notification” box to
active the S2VR Manager voice notification.
• Click the “Enable Email notification” box and
configure its settings to active S2VR Manager email notification.
9. Configuring RAID setting:
1. Click on “Configure RAID”.
2. Select and click “Create New RAID”.
Click IGNORE on the Disk Insertion msg.
3. Go to OS Disk Utility, select S2VR HD and
create Partition or RAID
• CONGRATULATIONS!
Your S2VR HD is ready to use! Thank you for your
purchase. Please visit us at www.caldigit.com
updated drivers and information on new CalDigit
products.
for
Loading...