
LTE Mini PCI-e Module User Manual 
LTE Mini PCI-e Module—LP 15 
User Manual 
V2.0 

LTE Mini PCI-e Module User Manual 
Revision History 

LTE Mini PCI-e Module User Manual 
Index 
REVISION HISTORY ......................................................................................................................................... 2 
1  INTRODUCTION ....................................................................................................................................... 4 
2  MECHANICAL INFORMATION ............................................................................................................. 4 
3  SPECIFICATIONS ..................................................................................................................................... 5 
3.1  RF PERFORMANCE ................................................................................................................................. 6 
3.1.1  RX Performance ................................................................................................................................ 6 
3.1.2  TX Performance ................................................................................................................................ 6 
3.1.3  UIM Card ......................................................................................................................................... 7 
3.1.4  USB PORT ........................................................................................................................................ 7 
3.1.5  RF Subsystem .................................................................................................................................... 7 
3.2  FULL-MINI PCI EXPRESS CARD PCB DETAILS ...................................................................................... 7 
4  REGULATORY AND SAFETY INFORMATION .................................................................................. 8 
4.1  REGULATORY APPROVALS..................................................................................................................... 8 
4.1.1  Transmitter ....................................................................................................................................... 8 
4.1.2  Receiver ............................................................................................................................................ 8 
4.1.3  FCC Compliance .............................................................................................................................. 8 
4.1.4  Labeling ............................................................................................................................................ 9 
4.2  RF ENERGY EXPOSURE INFORMATION .................................................................................................. 9 
5  INSTALLATION GUIDELINES ............................................................................................................. 10 
5.1  INTRODUCTION .................................................................................................................................... 10 
5.2  APPLICATION TYPE .............................................................................................................................. 10 

LTE Mini PCI-e Module User Manual 
1  Introduction 
LP15 is Mini-PCIE interface wireless LTE module base on LTE technology, which has high 
performance and durability and could be used in CPE, POS machine, electronic metering, 
security camera and medical care area. It has standard Mini PCI-e interface which is easy to 
be integrated. 
2  Mechanical Information 

LTE Mini PCI-e Module User Manual 
See details TX performance 
See details RX performance 
52 pin Full-Mini PCI Express Card interface 
3  Specifications 

LTE Mini PCI-e Module User Manual 
Reference sensitivity level 
(TDD) 
 Spurious emissions 
<-57 dBm@100KHz 
Maximum Power Reduction  
(MPR) 
 Error Vector Magnitude  
(EVM) 
PUSCH 17.5@QPSK BPSK ;12.5%@16QAM 
Carrier leakage 
<-24.2dBc@3.2 dBm ±3.2dB 
<-19.2dBc@-26.8 dBm ±3.2dB 
<-9.2dBc@-36.8 dBm ±3.2dB 
Adjacent Channel  
Leakage power Ratio 
Transmitter Spurious 
 emissions 
3.1  RF Performance 
3.1.1 RX Performance 
3.1.2 TX Performance 

LTE Mini PCI-e Module User Manual 
3.1.3 UIM Card 
LP15 supports UIM card. The UIM interface includes all the necessary signals, which are 
routed to the interface connector 
. 
3.1.4 USB PORT 
LP15 has USB client port, it can be used as debug, download, AT command and modem 
interface port. 
3.1.5 RF Subsystem 
LP15 includes all of the active BB and RF circuit, no need to add other RF components, 
suggest to have a Pi type antenna matching circuits if you want to have external antenna 
Note: The RF connector information: 
      Manufactory: I-PEX  
      MPN: 20279-001E-01 
3.2  Full-Mini PCI Express Card PCB Details 

LTE Mini PCI-e Module User Manual 
4  Regulatory and Safety Information 
4.1  Regulatory Approvals 
4.1.1 Transmitter 
LP15 have been tested and meet FCC (Part2/Part 90) regulatory requirements. 
4.1.2 Receiver 
The receiver associated with this transmitting device has been tested and declared to meet the 
regulatory requirements. 
4.1.3 FCC Compliance 
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition 
that this device does not cause harmful interference. 
The user should take caution that changes or modifications not expressly approved by 
manufacturer could void the user’s authority to operate this equipment. All required software  
and operating conditions must not be violated by the installer/user and is an express condition 
of use for this equipment. 
Modular Approval for use as a module in mobile-only exposure conditions. Only those 
antenna(s) specified in the filing may be used with this transmitter. This device is only 
authorized for OEM integration into host products; consumer or end-user installation is not 
allowed. The antenna(s) used for this transmitter must be installed to provide a separation 
distance of at least 20 cm from all persons. 

LTE Mini PCI-e Module User Manual 
4.1.4 Labeling 
The FCC labeling of the module is shown below. When integrating the module into a host, 
the label must be visible through a window, visible through an access panel that is easily 
removed, or a second label must be placed on the outside of the host device that contains the 
following text: Contains FCC ID: J26-4859300114.  
4.2  RF Exposure Compliance 
The LP15 module radio is intended for use in the Industrial Monitoring 
and Control and SCADA markets. The LP15 module unit must be 
professionally installed and must ensure a minimum separation distance 
between the radiating structure and any person. It is the responsibility of 
the user to guarantee compliance with the FCC MPE regulations when 
operating this device. 
LP15 module uses a low power radio frequency transmitter. The 
concentrated energy from an antenna may pose a health hazard. People 
should not be in front of the antenna when the transmitter is operating. 
The installer of this equipment must ensure the antenna is located or pointed such that it does 
not emit an RF field in excess of Health Canada limits for the general population. 
Recommended safety guidelines for the human exposure to radio frequency electromagnetic 
energy are contained in the Canadian Safety Code 6 (available from Health Canada) and the 
Federal Communications Commission (FCC) Bulletin 65. 
Any changes or modifications not expressly approved by the party responsible for 
compliance (in the country where used) could void the user's authority to operate the 
equipment. 
The resulted power density at a distance of 20 cm can be deducted as follows: 
EIRP = 23 + 2 = 25 dBm = 316 mW 
Power Density = EIRP*Duty Cycle/(4π R2) 

LTE Mini PCI-e Module User Manual 
= 305*1/(4*π *202) = 0.06 mW/cm
2 
Where DutyCycle is 1 and R is 20 cm, antenna gain is 2dBi 
The MPE limit for General Population/Uncontrolled Exposure is shown in the FCC OET 
Bulletin 65 Supplement C and can be calculated as follows: 
MPE limit = 790.5/1500 = 0.527 mW/cm
2 
5  Installation Guidelines 
5.1  Introduction 
Careful planning and preparation of any installation will always benefit the end result; always 
read and follow all installation instructions. Follow ESD precautions and prepare an ESD safe 
workspace for installation. Turn the power to the host off and ground yourself to dissipate 
static charge. 
Mount only in sockets and locations intended for Type F1 Full-Mini cards and consult 
manufacturer on thermal management recommendations for the module mounted within the 
host. 
5.2  Application Type 
The application type of the module is shown as bellow: 
All instructions relating to the integration of the module described on the FCC Grant notes 
must be followed.