CalAmp 140-5016-501, 140-5046-300, 140-5026-500, 140-5026-501, 140-5046-301 Quick Start Manual

Package Contents — Basic or Full-Duplex Unit

If you ordered Guardian part number:

Part Number

Description

140-5016-500

VHF 136-174 MHz Guardian Basic Unit

140-5016-501

VHF 136-174 MHz Guardian Full-Duplex Unit

140-5026-500

VHF 215-240 MHz Guardian Basic Unit

140-5026-501

VHF 215-240 MHz Guardian Full-Duplex Unit

140-5046-300

UHF 406.1-470 MHz Guardian Basic Unit

140-5046-301

UHF 406.1-470 MHz Guardian Full-Duplex Unit

140-5046-501

UHF 450-512 MHz Guardian Basic Unit

140-5046-501

UHF 450-512 MHz Guardian Full-Duplex Unit

140-5096-500

MAS 928-960 MHz Guardian Basic Unit

140-5096-501

MAS 928-960 MHz Guardian Full-Duplex Unit

Your package contains:

(1) Guardian Serial Modem
(1) Power Cable
(1) 8-Pole Socket Connector

Package Contents — Two-Piece Kit

If you ordered Guardian as part of a kit number:

Part Number Description

250-5016-500

VHF 136-174 MHz Guardian Demo Kit

250-5026-500

VHF 215-240 MHz Guardian Demo Kit

250-5046-300

UHF 406-470 MHz Guardian Demo Kit

250-5046-500

UHF 450-512 MHz Guardian Demo Kit

250-5096-500

MAS 928-960 MHz Guardian Demo Kit

Your package contains:

(2) Guardian Basic or Full-Duplex Serial Modems
(2) SMA-Male to BNC-Female Connectors
(2) SMA-Female to BNC-Male Connectors
(2) TNC-Male to BNC-Female Connectors
(2) Mini Circuits 5 W 20 dB Attenuators
(2) Flex Rubber Duck Antennas (VHF, UHF, or 900 MHz)
(2) 120 VAC to 12 VDC Power Supply
(1) 72 in. Serial Programming Cable
(1) Start Up CD-ROM and Product Information Card

Minimum Requirements

Interface and configuration of this device requires a user PC with an available serial COM
port interface, Microsoft Wind ows 98 or newer, and a web browser.

Technical Support

For assistance with this product, contact CalAmp technical support.

Email [e-mail]
Phone [phone]

Or visit the Support section of our website at http://www.calamp.com/support

.

Any changes or modifications not expressly approved by the party respons ible for compliance (in the country
where used) could void the user’s authority to operate the equipmen t.

CalAmp reserves the right to update its products, software, or d ocumentation without obligation to notify any
individual or entity. Product updates may result in differences between the information provided and the
product shipped. For access to the most current product documentation and application notes, visit

www.calamp.com

.

UL Listed models only

When operating at elevated temp erature extremes, the surface may exceed
+70 Celsius. For user safety, the Fusion should be installed in a restricted access
location.

WARNING — EXPLOSION HAZARD, do not connect while circuit is live unless
area is known to be non-hazardous.

1401 North Rice Avenue
Oxnard, CA 93030

Tel: [phone]
Fax: [phone]

e mail: [e-mail]

ABOUT CALAMP

CalAmp is a leading provider of wirele ss communications products that enable anytime/anywh ere
access to critical information, dat a and entertainment content. With comprehensive capa bilities
ranging from product design and devel opment through volume production, CalAmp deliver s cost­effective high quality solutions to a br oad array of customers and end markets. CalAmp is the
leading supplier of Direct Broadcast Satellite (DBS) outdoor customer premise equi pment to the
U.S. satellite television market. The Company also provides wireless data communication solutions
for the telemetry and asset tracking markets, private wireless networks, Interoperabl e Train Control
(ITC) radio transceivers for use in railroad Positive Train Co ntrol (PTC) applications, public safety
communications and critical infra structure and process control applications. For addit ional
information, please visit the Com pany’s website at www.calamp.com

.

Quick Start Guide

Guardian™

SERIAL RADIO MODEM FOR LICENSED SPECTRUM

© 2011-2014 CalAmp
PN 004-5006-000 Rev A
Revised October 2014

All specifications are typical and
subject to change without notice.

CalAmp

1401 N Rice Avenue

Oxnard, CA 93030

t: 805.987.9000 | f: 805.987.8359

www.calamp.com

Setup and Configuration

It is easy to set up a Guardian network to verify basic unit operation and experiment with
network designs and configurations. An Rx/Tx antenna is required for basic operation.

Important: Use attenuation between all demo units to reduce the amount of
signal strength in the test environment.

Device Connections

Refer to the following diagram for the proper device connections for ba sic operation.

Field Programming Software

The Guardian Field Programming Software (FPS) is the pro gramming and diagnostic
software for the Guardian seri al radio modem. The FPS allows the user to edit and
program user programmable settings, interactively tune modem and RF parameters, and
monitor diagnostic data from the Guardian.

INSTALLING THE FPS

To use the FPS, you will need a PC with Windows 98 or later and at least one operational
COM port available.

Step 1 Open the .zip file a nd open the setup.exe application. After the application is
extracted from the .zip file, th e Guardian Programmer Setup window opens. Click Next.

INSTALLING THE FPS (continued)

Step 2 Setup shows the destination location where the Guardian FPS files will be
installed. Click Next to continue.

Step 3 Setup shows the program group in the Start Menu that will be created or to which
the Guardian FPS will be added. Click Next to continue.

Note: Accept the default installation location and program group unless there is
reason to change them.

Setup displays the destination and program group and provides the opportunity to go
back to change either if necessary.

Step 4 Click Instal l to begin installation. Setup displays the progress as files are extracted
and installed and displays a window similar to the following when complete.

When finished, click Finish to exit Setup .

USING THE FPS

Make sure all connections are made as shown in the Device Connections diagram and
then power the Guardian.

Step 1 Locat e the CalAmp Utils program group (or if you named it differently during
installation) and select the Guardian application.

Step 2 From th e Guardian Programmer window, click Config in the upper left corner.
This will open the User Configuration window and read configuration information from
the device, auto-populating the Diagnostic s section, and the RSSI bar will indicate
received signal strength.

Step 3 Click Link Configuration in the lower left corner of the User Configuration
window. Set the RF Link, COM Port, and Modem Setting as required. Click Save Change s
when finished.

Your Guardian modem is now ready for use. For advanced network settings, please refer
to the Guardian Serial Radio Modem User Manual (PN 001-5006-000) provided, or our
online support library at www.calamp.com.