Cafe CZS22MSKSS User Manual
GEAppliances.com
Safety Instructions ............2–4
Operating Instructions
Automatic Ice maker ...........15, 16
Care and Cleaning .............18, 19
ClimateKeeper2
Crispers and Pans ..................14
CustomCool
Ice and Water Dispenser .......17–18
Quick Ice ...........................17
Refrigerator Doors .................13
Replacing the Light Bulbs ...........20
Set Features ........................6
Shelves and Bins ...............11, 12
Temperature Controls ...............5
TurboCool
Water Filter ........................10
Installation Instructions
Installing the Refrigerator .......30–33
Moving the Refrigerator ........26–29
Profile Side by Side
Preparing to Install
the Refrigerator ....................25
Trim Kits and Panels ............21–24
Water Line Installation .........34–36
™
™
.........................6
™
.................... 6
.....................7, 9
Owner’s Manual
and Installation
Models 22, 23, 25, 26, 27 and 29
Profile Côte à Côte
Réfrigérateurs
Manuel d’utilisation
et d’installation
La section française commence à la page 47
Profile Lado a Lado
Refrigeradores
Manual del propietario
e instalación
La sección en español empieza en la página 93
Troubleshooting Tips ......38–40
Normal Operating Sounds ..........37
Consumer Support
Performance Data Sheets ......43, 44
Warranty (U.S.) .....................42
Write the model and serial numbers
here:
Model # _________________________
Serial # __________________________
Find these numbers on a label inside
the refrigerator compartment at the
Refrigerators
top on the right side.
200D8074P052 49-60647-4 10-14 GE
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
SAFETY
GE Appliances website
For more information on your refrigerator’s operation, visit www.GEAppliances.com or
call 800.GECARES (800.432.2737). In Canada visit GEAppliances.ca or call 800.561.3344.
REFRIGERATOR SAFETY INFORMATION
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety
messages will follow the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These words are defined as:
DANGER
Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
This refrigerator must be properly installed and located in
accordance with the Installation Instructions before it is used.
Unplug the refrigerator before making repairs, replacing a light
bulb, or cleaning.
Note: Power to the refrigerator cannot be disconnected by any
setting on the control panel.
Note: Repairs must be performed by a qualified service
professional.
Replace all parts and panels before operating.
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
To reduce the risk of fire, explosion, electric shock, or injury when using your
refrigerator follow these basic safety precautions:
Because of potential safety hazards under certain conditions,
we strongly recommend against the use of an extension cord.
However, if you must use an extension cord, it is absolutely
necessary that it be a UL-listed (in the United States) or a
CSA certified (in Canada), 3-wire grounding type appliance
extension cord having a grounding type plug and outlet and
that the electrical rating of the cord be 15 amperes (minimum)
and 120 volts.
To prevent suffocation and entrapment hazards to children,
remove the fresh food and freezer doors from any refrigerator
before disposing of it or discontinuing its use.
Do not allow children to climb, stand or hang on the door
handles or the shelves in the refrigerator. They could seriously
injure themselves.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
Do not clean glass shelves or covers with warm water when
they are cold. Glass shelves and covers may break if exposed
to sudden temperature changes or impact, such as bumping
or dropping. Tempered glass is designed to shatter into many
small pieces if it breaks.
Keep fingers out of the “pinch point” areas; clearances
between the doors and between the doors and cabinet are
necessarily small. Be careful closing doors when children are in
the area.
Always clean the CustomCool™ Tray after thawing food.
To reduce the risk of injury when using your refrigerator, follow these basic
safety precautions.
2
Do not touch the cold surfaces in the freezer compartment
when hands are damp or wet, skin may stick to these
extremely cold surfaces.
Do not refreeze frozen foods which have thawed completely.
In refrigerators with automatic icemakers, avoid contact with
the moving parts of the ejector mechanism, or with the heating
element that releases the cubes. Do not place fingers or hands
on the automatic ice making mechanism while the refrigerator
is plugged in.
GEAppliances.com
SAFETY (CONT.)
INSTALLATION
WARNING
Explosion Hazard.
Keep flammable materials and vapors, such as gasoline, away from refrigerator. Failure to do so can
result in fire, explosion, or death.
CONNECTING ELECTRICITY
WARNING
Plug into a grounded 3-prong outlet
Do not remove the ground prong
Do not use an adapter
Failure to follow these instructions can result in death, fire, or electrical shock.
Electrical Shock Hazard.
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped with a
3-prong (grounding) plug which mates with a standard
3-prong (grounding) wall outlet to minimize the
possibility of electric shock hazard from this appliance.
Have the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly
grounded.
Where a standard 2-prong wall outlet is encountered,
it is your personal responsibility and obligation to have
it replaced with a properly grounded 3-prong wall
outlet. Do not use an adapter.
The refrigerator should always be plugged into its own
individual electrical outlet which has a voltage rating
that matches the rating plate.
A 115 Volt AC, 60 Hz, 15- or 20-amp fused, grounded
electrical supply is required. This provides the best
performance and also prevents overloading house
wiring circuits which could cause a fire hazard from
overheated wires.
Never unplug your refrigerator by pulling on the power
cord. Always grip plug firmly and pull straight out from
the outlet.
Repair or replace immediately all power cords that
have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end.
When moving the refrigerator away from the wall, be
careful not to roll over or damage the power cord.
PROPER DISPOSAL OF YOUR OLD REFRIGERATOR
WARNING
Remove fresh-food and freezer doors from the refrigerator, prior to disposal. Failure to do so can result
in child entrapment which can lead to death or brain damage.
IMPORTANT:
Suffocation and child entrapment hazard.
Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are
still dangerous even if they will sit for “just a few
days.” If you are getting rid of your old refrigerator,
please follow the instructions below to help prevent
accidents.
Before You Throw Away Your Old Refrigerator or
Freezer:
Take off the fresh food and freezer doors.
Leave the shelves in place so that children may
not easily climb inside.
Refrigerants
All refrigeration products contain refrigerants,
which under federal law must be removed prior
to product disposal. If you are getting rid of an old
refrigeration product, check with the company
handling the disposal about what to do.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
3
About the temperature controls.
Not all features are on all models. Your controls may be similar to the following:
Touch-LED Dispenser Control
NOTE: The refrigerator is shipped with
protective film covering the temperature
controls. If this film was not removed
during installation, remove it now.
The temperature controls are preset in the factory at 37°F (3°C) for the
refrigerator compartment and 0°F (-18°C) for the freezer compartment.
Allow 24 hours for the temperature to stabilize to the preset
recommended settings.
Refrigerator temperatures can be adjusted between 34°F and 46°F
(1°C to 8°C), and the freezer temperatures can be adjusted between –6°F
and +8°F (–21°C to –13°C).
To change the Refrigerator temperature:
Tactile-LED Dispenser Control
The temperature controls can display both the SET temperature as well
as the actual temperature in the refrigerator and freezer. The actual
temperature may vary slightly from the SET temperature based on
usage and operating environment.
On some models, setting both controls to the warmest setting until
the display flashes (off) will stop cooling in both the freezer and
refrigerator compartments.
On other models, setting either control to the warmest setting
until the display flashes (off) will stop the cooling to the freezer and
refrigerator.
NOTE: Turning the refrigerator off via the controls on the touch
panel does not shut off electrical power to the refrigerator.
NOTE: The refrigerator is shipped with protective film covering the
temperature controls. If this film was not removed during installation,
remove it now.
Touch-LED Dispenser Control:
To change the temperature, press and release the FREEZER
TEMP/FRIDGE TEMP pad. The SET light will come on and
the display will show the set temperature. To change the
temperature, tap either the > or > pad until the desired
temperature is displayed.
Once the desired temperature has been set, the temperature
display will return to the actual refrigerator and freezer
temperatures after 5 seconds. Several adjustments may be
required. Each time you adjust the controls, allow 24 hours for
the refrigerator to reach the temperature you have set.
The temperature controls can display both the SET temperature as well
as the actual temperature in the refrigerator and freezer. The actual
temperature may vary slightly from the SET temperature based on
usage and operating environment.
Turning the cooling system off: Tactile-LED Dispenser Control
On some models, setting both controls to the warmest setting until
the display flashes (off) will stop cooling in both the freezer and
refrigerator compartments.
On other models, setting either control to the warmest setting
until the display flashes (off) will stop the cooling to the freezer and
refrigerator.
NOTE: Turning the refrigerator off via the controls on the touch
panel does not shut off electrical power to the refrigerator.
Touch-LED Dispenser Control:
Press and release the FREEZER TEMP/FRIDGE TEMP pad.
Press>to set freezer temperature to 5. The display will
show OFF. To turn the unit back on, press the FREEZER
TEMP/FRIDGE TEMP pad. Press> to set the freezer and
refrigerator temperatures to the preset points of 0°F (-18°C)
for the freezer and 37°F (3°C) for the refrigerator.
When the unit is turned back on, it will take up to 24 hours
to stabilize.
Tactile LED Dispenser Control.
Performance Air Flow System
The Performance Air-Flow System is designed to maximize
temperature control in the refrigerator and freezer
compartments. This unique special feature consists of the
Air Tower along the back wall of the refrigerator and the Air
Tunnel on the bottom portion of the freezer rear wall. Placing
food in front of the louvers on these components will not affect
performance. Although the Air Tower and the Air Tunnel can
be removed, doing so will affect temperature performance.
(For removal instructions, on-line, contact us at ge.com or call
800.GE.CARES. In Canada, contact us at geappliances.ca or call
1.800.561.3344.)
4
About Set Features. GEAppliances.com
This pad is used to select the following features:
TurboCool, Quick Ice, Door Alarm and Water
Filter.
About TurboCool.™
How it Works
TurboCool™ rapidly cools the refrigerator
compartment in order to more quickly
cool foods. Use TurboCool™ when adding
a large amount of food to the refrigerator
compartment, putting away foods after they
have been sitting out at room temperature or
when putting away warm leftovers. It can also
OR
be used if the refrigerator has been without
power for an extended period.
Once activated, the compressor will turn
on immediately and the fans will cycle on
and off at high speed as needed for eight
hours. The compressor will continue to run
until the refrigerator compartment cools to
approximately 34°F (1°C), then it will cycle on
and off to maintain this setting. After 8 hours, or
if TurboCool™ is pressed again, the refrigerator
compartment will return to the original setting.
How to Use
Tactile LED Dispenser Control:
Press TurboCool™. The TurboCool temperature
display will show Tc and the LED will be activated.
After TurboCool™ is complete, the TurboCool™
indicator light will go out.
Pressing SET FEATURES repeatedly will cycle
through all of the available features and then
exit the mode. If no key is pressed, the mode
will exit and return to displaying features
currently set.
NOTES: The refrigerator temperature cannot be
changed during TurboCool™.
The freezer temperature is not affected
during TurboCool™.
When opening the refrigerator door during
TurboCool™, the fans will continue to run if
they have cycled on.
Touch-LED Dispenser Controls:
Press SET FEATURES. The refrigerator
temperature display will show TurboCool™
and/or TC. Press ON/OFF.
After TurboCool™ is complete, the refrigerator
compartment will return to the original setting.
NOTES:
The refrigerator temperature cannot be changed
during TurboCool™.
The freezer temperature is not affected during
TurboCool™.
When opening the refrigerator door during
TurboCool™, the fans will continue to run if they
have cycled on.
About ClimateKeeper2.
How it Works
The ClimateKeeper2™ is the industry’s most
advanced refrigeration system, delivering
optimum temperature and humidity
performance to keep food garden fresh longer
and reduce freezer burn.
The ClimateKeeper2™ system features two
HYDSRUDWRUV³RQHIRUWKHUHIULJHUDWRUDQGRQH
for the freezer.
This provides two separate cooling systems,
and separates the airflow between the fresh
food and freezer compartments during normal
cooling operations.*
This ensures that the humidity levels in the
fresh food compartment are significantly higher
than in a conventional system,** allowing fresh
produce and other unsealed foods to retain
their moisture content and freshness longer.
Moisture sensitive foods such as fresh fruit,
salads, rice, etc., can now be stored on open
shelves without excessive moisture loss.
™
(on some models)
Due to the higher humidity in the refrigerator,
you may on occasion experience fog or
small amounts of moisture in the refrigerator
compartment. This is normal and may
come and go as different food loads and
environmental conditions change. Wipe dry
with a paper towel if desired.
The separate airflow system minimizes the
mixing of air between the two compartments,
which reduces fresh food odor transfer to
improve the taste of ice.
The ClimateKeeper2™ system also reduces
the number of defrosting cycles in the freezer
evaporator, thereby reducing freezer burn.
* Freezer air is used in the CustomCool feature.
** Testing shows a higher level of humidity in
the Fresh Food section in ClimateKeeper2™
refrigerators versus conventional units.
5
About CustomCool™. (on some models)
How it Works
The CustomCool™ feature is used to quickly
chill items, thaw items or hold the pan at a
specific temperature. This feature is a system of
dampers, a fan, a temperature thermistor and
a heater.
How to Use
Empty the pan. Place the Chill/Thaw tray in
the pan. Place the items on the tray and
close the pan completely.
Touch LED Dispenser Control:
Select the ExpressThaw™, ExpressChill™
or SelectTemp™ pad. The display and SET
ExpressThaw
™
light will come on. Tap the pad until the light
appears next to the desired setting.
Use the following chart to determine the
best setting to use.
ExpressChill can be set to 15, 30 or 45
minutes. The default is 15 minutes.
To stop a feature before it is finished:
tap that feature’s pad until no options are
selected and the display is off.
Touch LED Dispenser Control
The pan is tightly sealed to prevent temperature
fluctuations in the rest of the refrigerator.
The controls for this pan are located on the
dispenser with the temperature controls.
NOTE: For food safety reasons, it is
recommended that foods be wrapped in plastic
wrap when using ExpressThaw. This will help
contain meat juices and improve thawing
performance.
During ExpressThaw and ExpressChill, the
display on the controls will count down the
time in the cycle (on some models).
After the ExpressThaw cycle is complete,
the pan will reset to the MEAT setting (32°F
[0°C]) to help preserve thawed items until
they are used.
The displayed actual temperature of the
CustomCool pan may vary slightly from
the SET temperature based on usage and
operating environment.
ExpressChill
™
6
About ExpressChill™. (on some models) GEAppliances.com
How it Works
ExpressChill
The ExpressChill™ feature is a system of
dampers, a fan and a temperature thermistor.
The pan is tightly sealed to prevent the pan’s
temperature from causing temperature
fluctuations in the rest of the refrigerator.
How to Use
Empty the pan. Place the Chill tray in the
pan. Place the items on the tray and close
the pan completely.
Select the ExpressChill™ pad. On some
models, you can then select the chill time
(use chart to determine best setting). Other
™
models will only have one option (45
minutes). On models with multiple settings,
tap the pad until the light appears next to
the desired setting.
The controls for this pan are located in the top
of the refrigerator or on the dispenser with the
temperature controls.
To stop a feature before it is finished, tap
that feature’s pad until no options are
selected and the display is off.
During ExpressChill, the display on the
controls will count down the time in the
cycle.
How to Remove and Replace the Drawer
To remove:
Pull the drawer out to the stop position.
Rotate all four swing locks to the unlock
position.
Lift the front of the drawer up and out.
To replace:
Make sure all four swing locks are in the
unlock position.
Place the sides of the drawer into the
drawer supports, making sure the swing
locks fit on the drawer slots.
Lock all four swing locks by rotating them
to the lock position.
7
About CustomCool™. (on some models)
CustomCool™ Chart
NOTE: Results may vary depending on packaging, starting temperature and other food traits.
ExpressThaw
0.5 Lb. (4 hours)
Hamburger Patties (0.5 lb)
Individually Wrapped
Filet Mignon (0.5 lb)
1.0 Lb. (6 hours)
Chicken Breasts (1.0 lb)
Ground Beef (1.0 lb)
Steak (1.0 lb)
2.0 Lbs. (10 hours)
Chicken Breasts (2.0 lbs)
Ground Beef (2.0 lbs)
Steak (2.0 lbs)
3.0 Lbs. (12 hours)
Chicken Breasts (3.0 lbs)
Ground Beef (3.0 lbs)
Steak (3.0 lbs)
™
1 Beverage Can (12 oz)
2 Small Juice Boxes (6–8 oz each)
2 to 6 Beverage Cans (12 oz each)
2 Plastic 20 oz Bottles of Beverage
4 to 6 Small Juice Boxes
(6–8 oz each)
3 Foil Juice Packets
2 Liter of Beverage
1/2 Gallon of Juice
Gelatin–1 package
ExpressChill
15 Minutes
30 Minutes
Wine (750 ml bottle)
45 Minutes
™
Oranges, Lemons, Limes, Pineapple,
Cantaloupe
Beans, Cucumbers, Tomatoes,
Peppers, Eggplant, Squash
Strawberries, Raspberries, Kiwifruit,
Pears, Cherries, Blackberries, Grapes,
Plums, Nectarines, Apples
Asparagus, Broccoli, Corn,
Mushrooms, Spinach, Cauliflower,
Kale, Green Onion, Beets, Onions
Raw Meat, Fish and Poultry
SelectTemp
Citrus Setting (43°F [6°C])
Produce Setting (35°F [2°C])
Meat Setting (32°F [0°C])
™
8
About the water filter. (on some models) GEAppliances.com
Water Filter Cartridge
The water filter cartridge is located in the back upper right
corner of the refrigerator compartment.
When to Replace the Filter on Models With a
Replacement Indicator Light
There is a replacement indicator light for the water filter
cartridge on the dispenser. This light will turn orange to tell you
that you need to replace the filter soon.
The filter cartridge should be replaced when the replacement
indicator light turns red or if the flow of water to the dispenser or
ice maker decreases.
When to Replace the Filter on Models Without a
Replacement Indicator Light
The filter cartridge should be replaced every six months or
earlier if the flow of water to the water dispenser or ice maker
decreases.
Removing the Filter Cartridge
If you are replacing the cartridge, first remove the old one by
slowly turning it to the left. Do not pull down on the cartridge. A
small amount of water may drip down.
Installing the Filter Cartridge
If you are replacing a SmartWater cartridge with an
adapter, it must be removed before installing the cartridge.
To remove the adapter, turn it to the left about 1/4 turn.
If you are replacing a Water by Culligan cartridge, leave the
adapter in place. This adapter will stay in the refrigerator when
you replace future cartridges.
Run water from the dispenser 1-1/2 gallons (about three
minutes) to clear the system and prevent sputtering.
Press and hold the WATER FILTER pad (on some models) on
the dispenser for 3 seconds.
NOTE: A newly-installed water filter cartridge may cause water
to spurt from the dispenser upon first use.
Filter Bypass Plug
You must use the filter bypass plug when a replacement filter
cartridge is not available. The dispenser and the ice maker will
not operate without the filter or filter bypass plug.
Filter
Bypass
Plug
Cartridge
Holder
SmartWater
Filter
Bypass
Plug
Water by Culligan
Some models
use this type of
With adapter Without adapter
(appearance may vary)
On models without a replacement indicator light, apply the
month and year sticker to the new cartridge to remind you
to replace the filter in six months.
Fill the replacement cartridge with water from the tap to
allow for better flow from the dispenser immediately after
installation.
Line up the arrow on the cartridge and the cartridge holder.
Place the top of the new cartridge up inside the holder. Do
not push it up into the holder.
Slowly turn it to the right until the filter cartridge stops.
DO NOT OVERTIGHTEN. As you turn the cartridge, it will
automatically raise itself into position. The cartridge will
move about 1/2 turn.
water filter.
To use the filter bypass plug on Water by Culligan models, you
must first remove the filter adapter from the cartridge holder by
turning it to the left.
For the maximum benefit of your filtration system, GE
recommends the use of GE branded SmartWater filters only.
Using GE branded filters in GE and Hotpoint refrigerators
provides optimal performance and reliability. GE branded
SmartWater filters are always the right choice because they
are patented and designed specifically for GE products. GE
SmartWater filters meet rigorous industry NSF standards for
safety and quality that are important for products that are
filtering your water. GE has not qualified non-GE branded
filters for use in GE and Hotpoint refrigerators and there is no
assurance that non-GE branded filters meet GE’s standards for
quality, performance and reliability.
,I\RXKDYHTXHVWLRQV³YLVLWRXU:HEVLWHDWGEAppliances.com, or
call 1.800.GE.CARES (1.800.432.2737).
Replacement filters:
To order additional filter cartridges in the United States,
visit our Website at GEAppliances.com, or call GE Parts and
Accessories, 800.626.2002.
See filter label for type of filter to order (MWF or MSWF).
Customers in Canada should consult the yellow pages for the
nearest Mabe Service Center.
9
About the shelves and bins.
Not all features are on all models.
Snugger
Refrigerator bin
Freezer tilt-out bin
Refrigerator Door Bins and Freezer Door Tilt-Out Bins
Bins
The larger refrigerator door bins and freezer
tilt-out door bins are adjustable.
To remove: Lift the front of the bin straight up,
then lift up and out.
To replace or relocate: Engage the back side
of the bin in the molded supports on the door.
Then push down on the front of the bin. Bin will
lock in place.
The snugger helps prevent tipping, spilling or
sliding of small items stored on the door shelf.
Place a finger on either side of the snugger
near the rear and move it back and forth
to fit your needs.
Top Freezer Bins
Do not block
Top freezer bin
Do not block
Top freezer bin (on some models)
NOTE:
Be careful when
placing items in
the top bin. Make
sure that items
do not block or
fall into the ice
chute.
NOTE:
Part must be in
place as shown
for proper ice
dispensing. Food
cannot be stored
in this location.
Press tab and pull shelf forward
to remove
Slide-Out Spillproof Shelf
The slide-out spillproof shelf allows you to
reach items stored behind others. The special
edges are designed to help prevent spills from
dripping to lower shelves.
To remove:
Slide the shelf out until it reaches the stop,
then press down on the tab and slide the shelf
straight out.
QuickSpace™ Shelf
This shelf splits in half and slides under itself for
storage of tall items on the shelf below.
This shelf can be removed and replaced or
relocated just like Slide-Out Spillproof Shelves.
To replace or relocate:
Line the shelf up with the supports and slide
it into place. The shelf can be repositioned
when the door is at 90° or more. To reposition
the shelf, slide the shelf past the stops and
angle downward. Slide shelf down to the
desired position, line up with the supports and
slide into place.
Make sure you push the shelves all the way
back in before you close the door.
On some models, this shelf cannot be used in
the lowest position.
10
GEAppliances.com
Not all features are on all models.
Freezer Baskets
To remove, push the basket all the way to the
back of the freezer. Lift up until the back pins
are disengaged. Lift the entire basket up and
pull out.
Slide-Out Freezer Shelves
To remove, slide out to the stop position, lift the
front past the stop position and slide out.
Fixed Freezer Shelves
There are two types of fixed freezer shelves.
To remove this type of shelf:
Lift the shelf up at the left side.
Bring the shelf out.
To remove this type of shelf:
Lift up the left side of the shelf and slide it
left into the center of the shelf supports.
Make sure you push the baskets all the way
back in before you close the door.
Make sure you push the shelves all the way
back in before you close the door.
NOTE FOR DISPENSER MODELS: In order to
take full advantage of the tilt-out ice bin, only
store items on the shelf below the ice bin that
are no taller than the lowest point on the bin.
Rotate the right side of the shelf up and out
of the shelf supports.
Door Wine/Beverage Rack (on some models)
This rack holds up to 5 cans or one bottle of
wine.
The rack hangs from the sides of the dairy bin.
To remove:
Empty the wine/beverage rack.
Holding the bottom of the dairy bin, lift the
front straight up, then lift up and out.
To detach the rack from the dairy bin, pull
the rack’s side wires out of the holes on
each side of the dairy bin.
To replace:
Reattach the rack to the sides of the bin.
Engage the back side of the bin in the
molded supports on the door. Then push
down on the front of the bin. The bin will
lock into place.
11
About the refrigerator doors.
Refrigerator Doors
When the door is only partially open,
it will automatically close.
Beyond this stop the door will stay
open.
The refrigerator doors may feel different than
the ones you are used to. The special door
opening/closing feature makes sure the doors
close all the way and are securely sealed.
When opening and closing the door, you will
notice a stop position. If the door is opened
past this stop point, the door will remain open
to allow you to load and unload food more
easily. When the door is only partially open, it
will automatically close.
Door Alignment
If doors are uneven, adjust the refrigerator
door.
Using a 7/16” wrench, turn the door
adjusting screw to the right to raise the
door, to the left to lower it. (A nylon plug,
imbedded in the threads of the pin,
prevents the pin from turning unless a
wrench is used.)
The resistance you feel at the stop position will
be reduced as the door is loaded with food.
After one or two turns of the wrench,
open and close the refrigerator door and
check the alignment at the top of the
doors.
12
7/16” Wrench
Raise
About the crispers and pans. GEAppliances.com
Not all features are on all models.
Fruit and Vegetable Crispers
Excess water that may accumulate in
the bottom of the drawers should be
wiped dry.
On some models, the bottom drawer has
full extension slides that allow full access
to the drawer.
HI
LO
Adjustable Humidity Crispers
Slide the control all the way to the HI setting to
provide high humidity recommended for most
vegetables.
D
L
O
C
C
O
L
D
E
S
T
Convertible Deli Pan
The convertible deli pan has its own cold
air duct to allow a stream of cold air from
the freezer compartment or fresh food
compartment to flow to the pan.
The variable temperature control regulates
the air flow from the Climate Keeper Air Tower.
About crisper removal.
Not all features are on all models.
Slide the control all the way to the LO
setting to provide lower humidity levels
recommended for most fruits.
Set the control to the coldest setting to store
fresh meats.
Set the control to cold to convert the pan
to normal refrigerator temperature and provide
extra vegetable storage space.
The cold air duct is turned off. Variable settings
between these extremes can
be selected.
Crisper Removal
Crispers can easily be removed by pulling the
drawer straight out and lifting the drawer up
and over the stop location.
If the door prevents you from taking out the
drawers, first try to remove the door bins.
If this does not offer enough clearance, the
refrigerator will need to be rolled forward
until the door opens enough to slide the
drawers out. In some cases, when you roll the
refrigerator out, you will need to move the
refrigerator to the left or right as you roll it out.
13
About the automatic ice maker.
A newly installed refrigerator may take 12 to 24 hours to begin making ice.
Automatic Ice maker
7KHLFHPDNHUZLOOSURGXFHVHYHQFXEHVSHUF\FOH³
approximately 100–130 cubes in a 24-hour period, depending
on freezer compartment temperature, room temperature,
number of door openings and other use conditions.
If the refrigerator is operated before the water connection is
made to the ice maker, set the power switch in the OFF position.
When the refrigerator has been connected to the water supply,
set the power switch to the ON position.
The ice maker will fill with water when it cools to 15°F (–10°C).
A newly installed refrigerator may take 12 to 24 hours to begin
making ice cubes.
You will hear a buzzing sound each time the ice maker fills with
water.
Throw away the first few batches of ice to allow the water line
to clear.
Be sure nothing interferes with the sweep of the feeler arm.
When the bin fills to the level of the feeler arm, the ice maker will
stop producing ice. It is normal for several cubes to be joined
together.
Special note about dispenser models:
Some models have a tilt-out ice bin. The bin can be tilted out
as shown in the illustrations, and it will hold itself up while you
take ice out or turn the ice maker power switch on and off. Be
sure to put the bin back in place before closing the door.
To restore your ice level from an empty bucket stage, the
following steps are recommended:
12 hours after the first batch of ice has fallen into the bin,
dispense 3 to 4 cubes.
After an additional 6 hours, dispense 3 to 4 cubes again.
These steps will restore your ice level in the shortest amount of
time.
Ice maker
Power
Switch
Ice maker
If ice is not used frequently, old ice cubes will become cloudy,
taste stale and shrv
CAUTION
Avoid contact with the moving parts of
the ejector mechanism, or with the heating element (located
on the bottom of the ice maker) that releases the cubes.
Do not place fingers or hands on the automatic ice making
mechanism while the refrigerator is plugged in.
Power
Switch
(on some models)
Feeler Arm
Green
Power Light
(on some models)
Feeler Arm
NOTE:
In homes with lower than average water pressure, you
may hear the ice maker cycle multiple times when making
one batch of ice.
14
About the automatic ice maker. (cont) GEAppliances.com
Accessing Ice and Reaching the Power Switch on
Dispenser Models
There are two types of ice storage bins on dispenser models.
One has a shelf above the bin, the other does not.
Special note for models with tilt-out ice bin:
These models have a tilt-out ice bin. The bin can be tilted
out as shown in the illustrations, and it will hold itself up
while you take ice out or turn the icemaker power switch
on and off. Be sure to put the bin back in place before
closing the door.
NOTE: In order to take full advantage of the tilt-out ice bin, only store items
on the shelf below the ice bin that are no taller than the lowest point on the
bin.
Models with a shelf above the ice bin
Shelf
Ice Bin
To reach the power switch, pull the
shelf straight out. Always be sure to
To access ice, pull the bin forward.
replace the shelf.
Shelf
Ice Bin
Models with tilt out ice bin
To access ice and reach the icemaker power switch:
Lift the bin, then pull it forward
until the bin stops.
Lower the bin to access ice or
reach the power switch.
Removing Ice Bin (dispenser models)
CAUTION
Set the power switch to the OFF position before removing the
bin.
When replacing the bin, be sure to press it firmly into place. If
it does not go all the way back, remove it and rotate the drive
mechanism 1/4 turn. Then push the bin back again.
The ice bin is heavy when full.
On some models, to access ice or reach the power switch:
Pull the bin forward until the
bin stops.
Rotate
Lower the bin to access ice or
reach the power switch.
Drive
Mechanism
Dispenser Models only
15
About the ice and water dispenser. (on some models)
To Use the Dispenser
Spill Shelf
Select CUBED, CRUSHED or WATER.
Press the glass gently against the top of the
dispenser cradle.
The spill shelf is not self-draining. To reduce
water spotting, the shelf and its grille should be
cleaned regularly.
If no water is dispensed when the refrigerator is
first installed, there may be air in the water line
system. Press the dispenser arm for at least two
minutes to remove trapped air from the water
line and to fill the water system. To flush out
impurities in the water line, throw away the first
six glassfuls of water.
CAUTION
objects into the ice crusher discharge opening.
Never put fingers or any other
Locking the Dispenser
Press the LOCK or LOCK CONTROLS pad for 3
seconds to lock the dispenser and control panel.
To unlock, press and hold the pad again for 3
seconds.
Dispenser Light
The LIGHT pad turns the light in the dispenser
on and off. The light also comes on when the
dispenser cradle is pressed. For models with a
bulb, if the light burns out, it should be replaced
with a 6 watt 12V maximum bulb. For LED
models contact Factory Service.
Door Alarm
Use Door Alarm to sound if either door is open
for more than 3 minutes. The alarm will stop
once the door is closed. For LCD models, a popup
screen will appear. The alarm can be silenced by
touching the LCD screen.
Touch LED Dispenser Control:
Press the SET FEATURES pad once and DOOR
ALARM will blink. Press ON/OFF and the door
alarm will be set and the icon will turn solid. Press
ON/OFF again to turn the alarm off.
Door Alarm (on Tactile LED Dispenser Control
model)
To set the alarm, press this pad until the indicator
light comes on. This alarm will sound if either
door is open for more than 3 minutes. The light
goes out and the beeping stops when you close
the door.
Quick Ice
When you need to speed up ice production, use the
Quick Ice feature. While this feature is turned on,
the freezer fan runs continuously for 48 hours, or
until the feature is turned OFF. During this period, ice
production will increase up to 40%. Models with the
integrated ice feature system require at FIRST USE at
least half an 8 oz. glass of ice to be dispensed every 6
to 12 hours. This will help the ice maker fill the bucket
properly so that dispensing is better.
How to Use
Touch LED Dispenser Control:
Press the SET FEATURES pad twice and QUICK ICE
will blink. Press ON/OFF to turn the feature on, then
again to turn it off.
Quick Ice (on Tactile LED Dispenser Control
model)
When you need ice in a hurry, press this pad
to speed up ice production. This will increase
ice production for the following 48 hours or
until you press the pad again.
16
GEAppliances.com
Precise Fill (on some models)
This water dispenser is equipped with a feature
called “precise fill.” This feature allows you to choose
a precise amount of water (cups or ounces) that
you would like dispensed. Pints and Liters are also
available for LCD models.
Touch LED Dispenser Control
Press the PRECISE FILL CUPS/OZ pad. The
WATER pad will light and the CRUSHED and
CUBED ice pads will turn off. The last unit used
will be displayed.
Press the PRECISE FILL pad again to toggle
between cups and ounces.
If you selected OUNCES, press the > or> pad to
select the number of ounces you would like to have
dispensed between 2–99 ounces. The default is 8
ounces.
If you selected CUPS, press the> or >pad to
select the amount you would like to have dispensed.
They are displayed as 1/4, 1/3, 1/2, 2/3 and 3/4, with
the highest amount being 16 3/4 cups. The default
is 1 cup.
Press the cup against the cradle and water will
begin dispensing. It will automatically stop when
the amount set has been dispensed. The display
will show the amount of water dispensed, beep,
then reset after 5 seconds.
NOTE: Do not leave the dispenser unattended when
water is being dispensed.
If you would like to stop dispensing water
before the specified amount has been
dispensed, just remove the cup from the cradle.
The display will show the amount that has been
dispensed for 5 seconds. If the cup switch is
pressed again within that time, the dispenser
will continue up to the set amount. If not, the
display will return to the set amount.
Important Facts About Your Dispenser
Do not add ice from trays or bags to
the storage drawer. It may not crush or
dispense well.
Avoid overfilling glass with ice and use of
narrow glasses. Backed-up ice can jam
the chute or cause the door in the chute
to freeze shut. If ice is blocking the chute,
poke it through with a wooden spoon.
Beverages and foods should not be
quick-chilled in the ice storage drawer.
Cans, bottles or food packages in the
storage drawer may cause the ice maker
or auger to jam.
To keep dispensed ice from missing the
glass, put the glass close to, but not
touching, the dispenser opening.
Some crushed ice may be dispensed
even though you selected CUBED. This
happens occasionally when a few cubes
accidentally get directed to the crusher.
After crushed ice is dispensed, some
water may drip from the chute.
Sometimes a small mound of snow will
form on the door in the ice chute. This
condition is normal and usually occurs
when you have dispensed crushed ice
repeatedly. The snow will eventually
evaporate.
17
Care and cleaning of the refrigerator.
Cleaning the Outside
The dispenser drip area, beneath the grille,
shou l d b e w i p e d d ry . W a t e r left in this area
may leave deposits. Remove the deposits by
Dispenser drip area.
adding undiluted vinegar to the well. Soak
until the deposits disappear or become loose
enough to rinse away.
The dispenser cradle. Before cleaning, lock
the dispenser by pressing and holding the
LOCK or LOCK CONTROLS pad for 3 seconds.
Clean with warm water and baking soda
VROXWLRQ³DERXWDWDEOHVSRRQPORI
baking soda to a quart (1 liter) of water. Rinse
thoroughly and wipe dry.
The door handles and trim. Clean with a
cloth dampened with soapy water. Dry with
a soft cloth.
The stainless steel doors and door handles
(on some models) can be cleaned with
a commercially available stainless steel
cleaner. Cleaners with oxalic acid such
as Bar Keepers Friend Soft Cleanser™ will
remove rust, tarnish and small blemishes.
Use only a liquid cleanser free of grit and
rub in the direction of the brush lines with a
damp soft sponge.
Do not use appliance wax or polish on the
stainless steel.
Keep the outside clean. Wipe with a
clean cloth lightly dampened with kitchen
appliance wax or mild liquid dish detergent.
Dry and polish with a clean, soft cloth.
Do not wipe the refrigerator with a soiled
dish cloth or wet towel. These may leave
a residue that can erode the paint. Do not
use scouring pads, powdered cleaners,
bleach or cleaners containing bleach
because these products can scratch and
weaken the paint finish.
Cleaning the Inside
To help prevent odors, leave an open box
of baking soda in the fresh food and freezer
compartments.
Unplug the refrigerator before cleaning. If
this is not practical, wring excess moisture
out of sponge or cloth when cleaning around
switches, lights or controls.
8VHZDUPZDWHUDQGEDNLQJVRGDVROXWLRQ³
about a tablespoon (15 ml) of baking soda to
a quart (1 liter) of water. This both cleans and
neutralizes odors. Rinse and wipe dry.
Use of any cleaning solution other than
that which is recommended, especially
those that contain petroleum distillates,
can crack or damage the interior of the
refrigerator.
CAUTION
shelves or covers with warm water
when they are cold. Glass shelves and
covers may break if exposed to sudden
temperature changes or impact such as
bumping or dropping. Tempered glass is
designed to shatter into many small pieces
if it breaks.
Do not wash any plastic refrigerator parts
in the dishwasher.
The chill/thaw tray is dishwasher safe.
Do not clean glass
18
GEAppliances.com
Behind the Refrigerator
Be careful when moving the refrigerator away
from the wall. All types of floor coverings can
be damaged, particularly cushioned coverings
and those with embossed surfaces.
Pull the refrigerator straight out and return it
to position by pushing it straight in. Moving the
refrigerator in a side direction may result in
damage to the floor covering or refrigerator.
Preparing for Vacation
For long vacations or absences, remove food
and unplug the refrigerator. Clean the interior
with a baking soda solution of one tablespoon
(15 ml) of baking soda to one quart (1 liter) of
water. Leave the doors open.
Set the ice maker power switch to the O (off)
position and shut off the water supply to the
refrigerator.
Preparing to Move
Secure all loose items such as shelves and
drawers by taping them securely in place to
prevent damage.
When pushing the refrigerator back, make
sure you don’t roll over the power cord or ice
maker supply line.
If the temperature can drop below freezing,
have a qualified servicer drain the water supply
system to prevent serious property damage
due to flooding.
When using a hand truck to move the
refrigerator, do not rest the front or back of the
refrigerator against the hand truck. This could
damage the refrigerator. Handle only from the
sides of the refrigerator.
Be sure the refrigerator stays in an upright
position during moving.
19
Replacing the light bulbs.(on some models)
WARNING
Before replacing a burned-out light bulb, the refrigerator should be unplugged in order to avoid contact with a
live wire filament. (A burned-out light bulb may break when being replaced.)
Turning the control to the OFF position does not remove power to the light circuit.
5HIULJHUDWRU&RPSDUWPHQW³8SSHU/LJKW
Your light shield will look like
one of the following:
Unplug the refrigerator.
The bulbs are located at the top of the
compartment, inside the light shield. On some
models, a screw at the front of the light shield
Tabs
will have to be removed. On other models, the
screw is located in the pocket located at the
back of the light shield.
OR
To remove the light shield, on some models,
press in on the tabs on the sides of the shield
and slide forward and out. On other models,
just slide the shield forward and out.
Pocket
5HIULJHUDWRU&RPSDUWPHQW³/RZHU/LJKW
This light is located above the top drawer.
C
O
L
D
D
L
E
O
S
C
T
Unplug the refrigerator.
Remove the convertible meat drawer
control knob by pulling straight out.
Lift the light shield up and pull it out.
After replacing the bulb with an appliance
bulb of the same or lower wattage, replace
the light shield and screws (on some models).
When replacing the light shield, make sure
that the tabs at the back of the shield fit into
the slots at the back of the light shield
housing.
Plug the refrigerator back in.
After replacing the bulb with an appliance
bulb of the same or lower wattage, replace
the shield and the knob.
Plug the refrigerator back in.
20
Freezer Compartment
Unplug the refrigerator.
Remove the shelf just above the light shield.
(The shelf will be easier to remove if it is
emptied first.) On some models, a screw at
the top of the light shield will need to be
removed.
To remove the light shield, press in on the
sides, and lift up and out.
Replace the bulb with an appliance bulb
of the same or lower wattage, and
reinstall the light shield. When
reinstalling the light shield, make sure
the top tabs snap securely into place.
Replace the screw (on some models).
Reinstall the shelf and plug the
refrigerator back in.
GEAppliances.com
WARNING
live wire filament. (A burned-out light bulb may break when being replaced.)
Turning the control to the OFF position does not remove power to the light circuit.
Before replacing a burned-out light bulb, the refrigerator should be unplugged in order to avoid contact with a
Dispenser (on some models)
Unplug the refrigerator.
The bulb is located on the dispenser under
the control panel. Remove the light bulb by
turning it counterclockwise.
Refrigerator Compartment (on models with LED lighting)
LED Lighting
Display
LED Lighting
Display
Some models may have LED lighting display
on the top and/or sides of the fresh food
compartment and in the rear and side of the
freezer compartment
If this assembly needs to be replaced, call GE
Service at 1.800.432.2737 in the United States
or 1.800.561.3344 in Canada.
Replace the bulb with a bulb of the same
size and wattage.
Plug the refrigerator back in.
21
Trim kits and decorator panels.
For CustomStyle™ models
Read these instructions completely and carefully.
Before You Begin
Some models are equipped with trim kits that allow you to install door panels. You can order pre-cut black, white,
bisque or stainless steel decorator panels from GE Parts and Accessories, 800.626.2002, or you can add wood
panels to match your kitchen cabinets.
Panels less than 1/4” (6 mm) thick
When installing wood panels less than 1/4” (6 mm) thick, you need to create a filler panel, such as 1/8” cardboard, that will fit
between the face of the door and the wood panel. If you are installing the pre-cut decorator panels, pre-cut filler panels are included
in the kit. The combined thickness of the decorator or wood panel and the filler panel should be 1/4” (6 mm).
Panels 1/4” thick or less
1/4” max
3/4” (19 mm) or Raised Panel
A raised panel design screwed or glued to a 1/4” (6 mm) thick backing, or a 3/4” (19 mm) routed board can be used. The raised
portion of the panel must be fabricated to permit clearances of at least 2” (5.1 cm) from the handle side for fingertip clearance.
Panels thicker than 1/4” (6 mm), up to 3/4” (19 mm) max, will require that the outer 5/16” (8 mm) of panel perimeter be no thicker
than 1/4” (6 mm).
Weight limitations for custom panels:
Fresh Food 38 lbs. (17 kg) max.
Freezer Door 28 lbs. (13 kg) max.
Panels thicker than 1/4” (6 mm)
5/16” (8 mm)
1/4” (6 mm) max
3/4” (19 mm)
2” (5.1 cm)
Clearance
Handle Side
Appearance
Panel
1/4” (6 mm)
Thick Backing
3/4”
(19 mm)
Refrigerator
Door
22
Trim kits and decorator panels. GEAppliances.com
23‘ Dimensions for Custom Wood Panels
The areas at the top of the panels need to be cut out of the panels.
Freezer Panel
Without Dispenser
Freezer Panel
With Dispenser
Fresh Food Panel
1/8” (3 mm)
177ø8”
(45.4 cm)
FRONT
1415ø32”
(36.8 cm)
335ø8”
(85.4 cm)
25‘
CustomStyle™
Cutout
5/16”
(8 mm)
1/8” (3 mm)
679ø32”
(170.9 cm)
FRONT
1415ø32”
(36.8 cm)
Cutout
5/16”
(8 mm)
Dimensions for Custom Wood Panels
The areas at the top of the panels need to be cut out of the panels.
1/8” (3 mm)
679ø32”
(170.9 cm)
FRONT
1915ø32”
(49.5 cm)
Cutout
5/16”
(8 mm)
Freezer Panel
Without Dispenser
Cutout
5/16”
(8 mm)
(175.3 cm)
1/8” (3 mm)
69”
FRONT
1415ø32”
(36.8 cm)
Cutout
5/16”
(8 mm)
Freezer Panel
With Dispenser
1/8” (3 mm)
17”
(43.2 cm)
FRONT
1415ø32”
(36.8 cm)
361ø4”
(92.0 cm)
Fresh Food Panel
1/8” (3 mm)
69”
(175.3 cm)
FRONT
1915ø32”
(49.5 cm)
Cutout
5/16”
(8 mm)
23
Inserting the door panels.
Read these instructions completely and carefully.
Insert the Freezer Panel and Fresh Food Panel.
Carefully push the freezer panel in until it slides
into the slot behind the door handle. Push the filler
If your model has a dispenser, this step only applies to
the fresh food panel and top freezer panel.
panel (required with some door panels) in behind the
decorator panel. Repeat for fresh food panel.
Insert the Bottom Freezer Panel (on dispenser models).
Carefully push the panel in until it slides into the slot
behind the door handle. Push the filler panel (required
with some door panels) in behind the decorator panel.
Attach the Top Trim on the Freezer and Fresh Food Doors.
The Top Trim can be found inside the refrigerator
compartment.
With a T-20 Torxdriver, attach the Top Trim, using two
screws on each Top Trim piece, to the top of each door.
Top Trim Screws
Top Trim Screws
Hand tighten only. Make sure that the top of each panel
fits snugly behind the lip of the Top Trim.
Cut-Out
Side Trim
Cut-Out
Top
Freezer
Panel
Fresh
Food
Panel
Bottom
Freezer
Panel
Side Trim
24
GEAppliances.com
Install the Side Trim.
These pieces are tucked inside the refrigerator door
handle.
Do not remove the protective film on the outside of the
Side Trim until the Side Trim is installed.
Fit the bottom of the Side Trim under the Bottom Trim as
illustrated.
Top Trim
Side
Trim
Hold the Side Trim against the front face of the decorator
panels and fit the Side Trim under the Top Trim. Make sure
the magnetically attached Side Trim is fitted correctly and
that you are satisfied with the appearance of all the parts.
Side
Trim
Bottom Trim
25
Installation
Refrigerator
Instructions
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
In Canada, call 1.800.561.3344 or Visit our Website at: geappliances.ca
Models 22, 23, 25, 26, 27 and 29
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
•
IMPORTANT ³ Save these instructions
for local inspector’s use.
•
IMPORTANT ³ Observe all governing
codes and ordinances.
•
Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions
for future reference.
• Skill level – Installation of this appliance requires
basic mechanical skills.
• Completion time –
Water Line Installation
• Proper installation is the responsibility of
the installer.
• Product failure due to improper installation is not
covered under the Warranty.
If the refrigerator has already been installed,
remove the base grille (see Step 2 in Moving
the Refrigerator), then skip to Step 5 in Installing
the Refrigerator.
Refrigerator Installation
30 minutes
30 minutes
PREPARATION
WATER SUPPLY TO THE ICE MAKER
If the refrigerator has an ice maker, it will have
to be connected to a cold water line. A GE water
supply kit (containing tubing, shutoff valve, fittings
and instructions) is available at extra cost from your
dealer, by visiting our Website at ge.com (in Canada
at geappliances.ca) or from Parts and Accessories,
800.626.2002 (in Canada 1.888.261.3055).
TOOLS YOU WILL NEED
3/8” and 5/16” Socket 1/2” and 7/16” Wrench
1/8” Hex Wrench
Plastic Putty Knife
26
Phillips Head Screwdriver
Installation Instructions
MOVING THE REFRIGERATOR
LOADING THE REFRIGERATOR
1
ONTO A HAND TRUCK
Leave all tape and door pads on doors until
the refrigerator is in its final location.
To move the refrigerator, use a padded hand
truck. Center the refrigerator on the hand truck
and secure the strap around the refrigerator.
DO NOT OVERTIGHTEN THE STRAP.
If the refrigerator must go through
DQ\HQWUDQFHWKDWLVOHVVWKDQZLGH
the doors must be removed. Proceed
to Step 3.
DO NOT remove the handles.
,IDOOHQWUDQFHVDUHPRUHWKDQZLGH
skip to Installing the Refrigerator.
DISCONNECT THE WATER COUPLING
3
(on some models)
If the refrigerator has a water dispenser,
there is a water line from the cabinet into
the bottom hinge on the freezer door that
must be disconnected.
To disconnect, push in on the white collar
of the coupling and pull out the tubing.
White collar
REMOVE THE BASE GRILLE
2
Remove the grille by removing the two Phillips
head screws.
Bottom
freezer
hinge
27
Installation Instructions
MOVING THE REFRIGERATOR (CONT.)
DISCONNECT THE POWER COUPLING
4
(on some models)
If the refrigerator has a water dispenser,
there is a power line (harness) from the cabinet
into the bottom hinge on the freezer door that
must be disconnected.
To disconnect, pull apart at the coupling.
Bottom
freezer
hinge
DISCONNECT THE ELECTRICAL
5
CONNECTORS (on some models)
If the refrigerator has a refreshment center,
there are electrical connectors (harnesses)
from the cabinet into the bottom hinge
on the refrigerator door that must be
disconnected.
To disconnect, pull apart each connector.
CLOSE THE FREEZER AND
6
REFRIGERATOR DOORS
REMOVE THE FREEZER DOOR
7
Remove the freezer door top hinge cover
A
(if equipped) by either squeezing it and pulling it
up or by prying it off with a plastic putty knife.
Remove the two 5/16” or 1/8” hex head screws,
B
then lift the hinge straight up to free the hinge pin.
5/16” or 1/8” hex head
Bottom
refrigerator
hinge
28
Open the freezer door to 90.°
C
90°
Installation Instructions
REMOVE THE FREEZER DOOR (cont.)
7
As one person slowly lifts the freezer door up
D
and off the bottom hinge, the second person
should carefully guide the water line and power
line (harness) through the bottom hinge.
90°
Set the door on a non-scratching surface with
E
the inside up.
REMOVE THE REFRIGERATOR DOOR
8
Remove the refrigerator door top hinge cover
A
(if equipped) by either squeezing it and pulling it
up or by prying it off with a plastic putty knife.
REMOVE THE REFRIGERATOR DOOR
8
(cont.)
Remove the two 5/16” or 1/8” hex head screws,
B
then lift the hinge straight up to free the hinge
pin.
5/16” or 1/8” hex head
Open the refrigerator door to 90.°
C
90°
29
Installation Instructions
MOVING THE REFRIGERATOR (CONT.)
REMOVE THE REFRIGERATOR DOOR
8
(cont.)
Lift the refrigerator door up and off the bottom
D
hinge.
If the refrigerator has a refreshment center,
one person should slowly lift the door up and
off the bottom hinge and the second person
should carefully guide the electrical lines
(harnesses) through the bottom hinge.
90°
Refreshment Center Models Only
Set the door on a non-scratching surface with
E
the inside up.
REPLACING THE DOORS
9
To replace the doors, simply reverse steps
3 through 8.
However, please note the following:
• When lowering the doors onto the bottom
hinges, make sure the second person
carefully guides the tube and harnesses
through the holes in the hinges.
• When connecting the water line, make sure
you insert the tubing all the way to the mark.
Mark
• Do not pinch the tubing and harnesses when
placing the doors on the bottom hinges.
• When connecting the power line and the
electrical lines (refreshment center models
only), be sure that the connectors are seated
together fully.
30
Loading...