Cafe CVW73014MWM, CVW73614MWM User Manual

Owner's Manual

Wall Chimney Vent Hoods

Models: CVW7301 - 30" Glass

CVW7361 - 36" Glass

Contents

Safety Information ...............................3

Using the Hood

Controls ......................................5

Filter .........................................6

Care And Cleaning

Surfaces ......................................7

Lights ........................................7

Troubleshooting Tips ............................8

Limited Warranty ...............................10

Accessories ...................................11

Consumer Support .............................12

Write the model and serial numbers here:

Model # _______________________________

Serial # _______________________________

You can find them on a label on the inside of the hood.

Español

Para consultar una version en español de este manual de instrucciones,

visite nuestro sitio de internet cafeappliances.com.

49-2000062 05-18 GEA

THANK YOU FOR MAKING CAFÉ A PART OF YOUR HOME.

We take pride in the craftsmanship, innovation and design that goes into every CAFÉ product, and

we think you will too. Among other things, registration of your appliance ensures that we can deliver

important product information and warranty details when you need them.

section of this Owner’s Manual. You may also mail in the pre-printed registration card included in the

packing material.

2 49-2000062

IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING

SAFETY INFORMATION

WARNING

ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

A. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the manufacturer.

B. Before servicing or cleaning unit, switch power off

at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

C. Do not use this unit with any solid-state speed

control device.

D. This unit must be grounded.

CAUTION

ONLY. DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS AND VAPORS.

CAUTION

TO PROPERLY EXHAUST AIR, BE SURE TO DUCT AIR OUTSIDE. DO NOT VENT EXHAUST AIR INTO SPACES WITHIN WALLS OR CEILINGS OR INTO ATTICS, CRAWL SPACES OR GARAGES.

TO REDUCE THE RISK OF FIRE,

FOR GENERAL VENTILATING USE

TO REDUCE RISK OF FIRE AND

WARNING

TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

A. SMOTHER FLAMES with a close-fitting lid, cookie

sheet or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

B. NEVER PICK UP A FLAMING PAN—You may be

burned.

C. DO NOT USE WATER, including wet dishcloths or

towels—a violent steam explosion will result.

D. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

2. The fire is small and contained in the area where it started.

3. The fire department is being called.

4. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety” published by NFPA.

TO REDUCE THE RISK OF INJURY

READ AND SAVE THESE INSTRUCTIONS

49-2000062 3

IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING

WARNING

RANGE TOP GREASE FIRE:

A. Never leave surface units unattended at high

settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on medium settings.

B. Always turn hood ON when cooking at high heat or

when flambéing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

C. Clean ventilating fans frequently. Grease should not

be allowed to accumulate on fan or filter.

SAFETY INFORMATION

D. Use proper pan size. Always use cookware

appropriate for the size of the surface element.

WARNING

ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

A. Installation work and electrical wiring must be

done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.

B. Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guidelines and safety standards such as those published by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.

TO REDUCE THE RISK OF A

TO REDUCE THE RISK OF FIRE,

C. When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities. D. Ducted fans must always be vented to the outdoors. E. When applicable, install any makeup (replacement)

air system in accordance with local building code

requirements. Visit cafeappliances.com for

available makeup air solutions. F. Turn off breaker to adjacent rooms while working.

WARNING

USE ONLY METAL DUCTWORK.

Ŷ'RQRWDWWHPSWWRUHSDLURUUHSODFHDQ\SDUWRI\RXU

hood unless it is specifically recommended in this manual. All other servicing should be referred to a qualified technician.

TO REDUCE THE RISK OF FIRE,

How to Remove Protective Shipping Film and Packaging Tape

Carefully grasp a corner of the protective shipping film with your fingers and slowly peel it from the appliance surface. Do not use any sharp items to remove the film. Remove all of the film before using the appliance for the first time.

To assure no damage is done to the finish of the product, the safest way to remove the adhesive from packaging tape on new appliances is an application of a household liquid dishwashing detergent. Apply with a soft cloth and allow to soak. NOTE: If surface is still not clean, see page 8 for more cleaning options.

NOTE: The adhesive must be removed from all parts.

READ AND SAVE THESE INSTRUCTIONS

4 49-2000062

Controls

USING THE HOOD: Controls

1. Rangehood Control Panel:

is located on the front of the canopy. The position and function of each control button are noted below.

Light Button: On/Night/Off switch for the halogen

lights. Press the LIGHT button to turn the lights on, again to set the lights to night setting, and again to turn off.

The control panel

3. Fan Off Button: Off switch for the fan. The fan

can be operated by pressing any of the fan setting buttons. Hold for 2 seconds to activate auto off after 15 minutes.

4. Fan Settings Buttons: Speed control for

fan. Press the switch Lo for LOW speed, Med for MEDIUM speed and Hi for HIGH speed. Hold down the Hi button for 2 seconds to activate the BOOST SPEED that will run for 10 minutes.

49-2000062 5

Filters

Be sure the circuit breaker is off and all surfaces are cool before cleaning or servicing any part of the vent hood.

Metal Grease Filter

The metal filter traps grease released by foods from cooking.

The filters must ALWAYS be in place when the hood is in use. The grease filters are dishwasher-safe and should be cleaned every 6 months, or as needed.

To remove:

Pull downward on the filter lock to release the filter.

To replace:

Fit the tabs at the bottom of the filter behind the ledge of the filter opening. Lift up the front side of the filter, push downward on the filter lock, and push gently until the filter is in place. Release the filter lock to secure the filter in place.

To clean, swish the filter in hot soapy water and rinse in clean water or wash it in the dishwasher. Do not use abrasive cleansers.

NOTE: Some discoloration may occur in the dishwasher.

CARE AND CLEANING: Filters

Filter Lock

For Recirculation Installation Only Charcoal Filter (Not Included)

If the model is not vented to the outside, the air needs to be recirculated through a disposable charcoal filter that helps remove smoke and odors.

NOTE: DO NOT rinse, or put charcoal filter in an automatic dishwasher.

The charcoal filter cannot be cleaned. It must be replaced. It is recommended that the charcoal filter be replaced every 6-12 months or if it is noticeably dirty or discolored.

Order Charcoal Filter JXCF71

To inquire about purchasing replacement charcoal filters or to find the location of a dealer nearest you, visit

cafeappliances.com/parts. To install:

1. Insert the bottom tabs of the charcoal filter into the two slots at the back of the unit. Pivot filter upward into place while depressing the locking tabs.

2. Replace the metal filter—see Metal grease filter section.

To remove:

1. Remove the metal filter—see Metal grease filter section.

Press on the two tabs on the charcoal filter to

disengage the lock and pivot to remove.

6 49-2000062

Surfaces

Stainless Steel Surfaces (on some models)

Do not use a steel wool pad; it will scratch the surface.

To clean the stainless steel surface, use warm sudsy water or a stainless steel cleaner or polish. Always wipe the surface in the direction of the brush line. Follow the cleaner instructions for cleaning the stainless steel surface. Cleaners with oxalic acid such as Bar Keepers Friend Soft Cleanser™ will remove surface rust, tarnish, and small blemishes. Use only a liquid cleanser free of grit and rub in the direction of the brush lines with a damp soft sponge.

Painted Surfaces (on some models)

Do not use a steel wool pads or other abrasive cleaners; they will scratch the surface.

Clean grease-laden surfaces of the hood frequently. To clean the hood surface, use a hot, damp cloth with a mild detergent suitable for painted surfaces. About one tablespoon of ammonia may be added to the water. Use a clean, hot, damp cloth to remove soap. Dry with a dry, clean cloth.

To inquire about purchasing stainless steel appliance cleaner or polish, or to find the location of a dealer nearest you, visit cafeappliances.com/parts.

NOTE: When cleaning, take care not to come in contact with filters and other surfaces.

CAUTION

be certain that you do not touch the light with moist hands or cloth. A warm or hot light may break if touched with a moist surface. Always let the light cool completely before cleaning around it.

When cleaning the hood surfaces,

CARE AND CLEANING: Surfaces / Lights

Lights

CAUTION

To change the lights:

1. Before attempting to replace the lights, make sure that the light switch is turned off.

2. Wear gloves. Do not touch the light with your bare fingers. Skin oils can cause early light failure. Wear clean gloves or use a paper towel to handle the light.

3. Using a flathead screwdriver, unclip the metal trim ring from the lighting support.

4. Remove the light by pulling towards the front of the hood. Replace it with a new G4 20W Clear Halogen Capsule light by inserting the two stakes into the holes and pushing towards the back of the hood to secure the light.

5. Reinsert the metal trim ring by lining up the two side holes on the lighting support with the two tabs on the trim ring, and push upward.

Allow lights to cool before touching.

49-2000062 7

Troubleshooting tips ... Before you schedule service

Save time and money! Review the charts on the following pages first and you may not need to schedule service.

Problem Possible Cause What To Do

Fan/Light does not operate when either button is pressed

Fan does not operate when fan Lo, Med, Hight buttons are pressed

Loud or abnormal airflow noise

Fan fails to circulate air or moves air slower than normal and/or

TROUBLESHOOTING TIPS

fan is making loud or abnormal airflow noise

The hood controls are not operating correctly

Early light failure

A house fuse may be blown or a circuit breaker tripped.

The blower connector is loose or not plugged into its mating connector.

Wrong duct size used in installation. This hood requires 6” ducting to perform optimally. Using

Obstructions in duct work. Make sure nothing is blocking the vent. Make sure your

Damper blade on wall or roof cap may not be open.

Metal grease filter and charcoal filter (if present) may be dirty.

Insufficient makeup (replacement) air Sufficient makeup (replacement) air is required for

Control logic confused. Disconnect power to the hood by resetting the circuit

Replacing lights with bare hands.

Light wattage is too high. Replace with correct wattage.

Replace fuse or reset circuit breaker.

Disconnect power to the unit. Remove the filters and look up at the blower. If the blower connector plug is loose or you see the connector dangling, the installer failed to plug it in securely. See the mini manual for the plug location and how to plug in the connector.

smaller duct pipe will cause reduced venting. Minimize the duct run length and number of transitions and elbows. CAFÉ service technicians cannot correct this issue if installed improperly.

wall or roof cap has a blade or door. Make sure damper swings freely. Damper blades may

flip over and will not fully open when this happens. Adjust to original position.

Clean the metal grease filter and replace charcoal filter (if present). See Care and Cleaning of the Vent Hood.

exhausting appliances to operate to rating. Check with local building codes, which may require or strongly advise the use of makeup air. Visit cafeappliances.com for available makeup air solutions.

breaker. Wait 30 seconds to allow controls to reset. Replace lights while wearing gloves to keep skin oils

off lights.

8 49-2000062

+ 16 hidden pages