Cafe CSB913M2NS5, CSB913P3ND1 Installation manual

INSTALLATION
INSTRUCTIONS

Advantium

®

Built-In Wall Oven

CSB913

MFL59060928_00

31-2000354 Rev.0

03-19 GEA

Español

For a Spanish version of this manual, visit
our Website at cafeappliances.com.

Para consultar una version en español de
este manual de instrucciones, visite nuestro
sitio de internet cafeappliances.com.

Safety Information

BEFORE YOU BEGIN

Read these instructions completely and
carefully.

IMPORTANT

for local inspector’s use.

IMPORTANT

and ordinances.

• Note to Installer — Be sure to leave these

instructions with the Consumer.

• Note to Consumer — Keep these instructions

with your Owner’s Manual for future reference.

• Skill Level — Installation of this appliance

requires basic mechanical and electrical skills.

• Completion Time — 1 Hour.

• Proper installation is the responsibility

of the installer. Product failure due to improper
installation is not covered under the warranty.
See Owner’s Manual for warranty information.

IMPORTANT

intended purpose. Never use the oven for
warming or heating a room. Prolonged use
of the oven without proper ventilation can be
hazardous.

CAUTION

breaker before beginning installation to avoid
severe or fatal shock injury.

CAUTION

capable of supporting the cabinet load, in addition
to the added weight of the oven and drawer, plus
additional oven loads.

—

Save these instructions

—

Observe all governing codes

—

Use this oven only for its

For personal safety, remove
house fuse or oven circuit

For personal safety, the
mounting surface must be

CONTENTS

Design Information

Models Available ..............................................2

Product Dimensions and Clearances ............... 3

Tools and Parts Required ................................3

Advance Planning ............................................ 3

Installation Preparation

Electrical Requirements ................................... 4

Preparing the Opening (Standard) ................... 5

Preparing the Opening (Flush Mount) .............. 9

Storage Drawer Preparation

Standard ........................................................ 11

Flush ..............................................................11

Installation Instructions

Step 1, Remove Packaging and Parts ........... 12

Step 2, Slide the Oven into the Cutout .......... 13

Step 3, Install Bottom Trim ............................. 13

Step 4, Install Bottom Trim with Accessory

Drawer .......................................................... 13

Step 5, Install Mounting Screws ..................... 14

Step 6, Finalize Installation ............................ 14

MODELS AVAILABLE

Café Pro Models:

CSB913P2NS1 – Stainless Steel
CSB913P3ND1 – Matte Black
CSB913P4NW2 – Matte White

Café Min Model

CSB913M2NS5 – Stainless Steel

* Accessory storage drawer is only available for

stainless steel models

2 31-2000354 Rev. 0

Design Information

PRODUCT DIMENSIONS AND CLEARANCES

NOTE: Appearance will vary by model.

21-1/2Ǝ

2-1/4Ǝ

1Ǝ

1-1/4Ǝ

13 1/4Ǝ

29-3/4Ǝ

20 1/8Ǝ

TOOLS AND PARTS REQUIRED

(NOT SUPPLIED)

• #2 Phillips screwdriver

• Hand-held drill

• High speed drill bit, 3/32Ǝ diameter

• 3/8Ǝ slot-head screwdriver

• Level

• Saw

• 3/8Ǝ min. plywood for floor (if required)

• Wood screws or other hardware for installing runner

or shelf to support oven (if required)

• Safety glasses or goggles

FLUSH MOUNT INSTALLATION

This installation method allows for the unit face to be
inline with the cabinet face.

IMPORTANT: HIGH SKILL LEVEL IN CARPENTRY
IS REQUIRED. Non-standard cabinetry may be

required.

Flush installation of the oven will lead to the exposure
of the cabinet face frame edges.

Side cleats may be visible and should be a finished
surface.

ADVANCE PLANNING

7KHVHRYHQVPD\EHLQVWDOOHGGLUHFWO\LQWRDƎ

wide oven cabinet with standard installation.

• Cutout height dimensions are different for
installations with an accessory storage drawer.
Make sure to use the correct cutout when preparing
the opening.

• Allow for clearance to adjacent corners, walls,
drawers, etc.

• Cabinets installed adjacent to wall ovens must have
an adhesion spec of at least 194ºF temperature
rating.

The oven must be securely installed in a cabinet that
is firmly attached to the house structure. Weight on
the oven door could cause the oven to tip and result
in injury. Never allow anyone to climb, sit, stand or
hang on the oven door.

If installing the drawer accessory, the drawer must
be assembled to the oven prior to installation into
the cabinet. See the Accessory Storage Drawer

Assembly Instructions.

31-2000354 Rev.0 3

Installation Preparation

ELECTRICAL REQUIREMENTS

Single Advantium Built-In Oven Installation:

This product requires a 120-volt, 60 Hz, 15-amp
circuit and draws 1.8 kilowatts. This product must be
connected to a supply circuit of the proper voltage and
frequency.

• Wire size must conform to the requirements of the
National Electrical Code or the prevailing local code for
this kilowatt rating.

• The power supply cord and plug should be brought
to a separate 15 or 20 ampere branch circuit single
grounded receptacle. The outlet box should be located
within reach of the 48” power cord.

ELECTRICAL LOCATION

6”

9”

Locate outlet box in the shaded area

Install a recessed electrical outlet
in the back wall of the opening
within 6Ǝ of either side and at least
9Ǝ above the cutout floor.

GROUNDING INSTRUCTIONS

WARNING

Ensure Proper ground
exists before use.

power cord having a grounding wire with a grounding
plug. The plug must be plugged into an outlet that is
properly installed and grounded.

Consult a qualified electrician or service technician if
the GROUNDING INSTRUCTIONS are not completely
understood, or if doubt exists as to whether the

Improper use of the grounding plug can result in a risk of electric shock.

This appliance must be grounded.
In the event of an electrical short
circuit, grounding reduces the risk
of electric shock by providing an
escape wire for the electric current.

This appliance is equipped with a

appliance is properly grounded.
If the outlet is a standarf 2-prong wall outlet, it is your

personal responsibility and obligation to have it replaced
with a properly grounded 3-prong wall outlet.

Do not under any circumstacnes cut or remove the third
(ground) prong from the power cord.

Do not use an extension cord. If the power cord is too
short, have a qualified electrician or service technician
install an outlet near the appliance.

For best operation, plug this appliance into its own
electrical outlet to prevent flickering of lights, blowing of

fuse or tripping of circuit breaker.

4 31-2000354 Rev. 0

Standard Installation Preparation

PREPARE THE OPENING

Advantium Built-In Oven can be installed in
combination with other Built-In appliances. Always
follow each product’s Installation Instructions to
complete the installation.

Single Advantium Built-In Oven Installation:

Order a 30” wide single oven cabinet or cut the
opening in a wall to the dimensions shown.

30”

17-1/2”

36-3/4”

Min.

23-1/2”

25-1/4”

Construct
solid bottom

- Min. 3/8”
plywood
supported
on all four
sides. Must
be able to
support
weight of
oven and
contents.

PREPARE THE OPENING (CONT.)

Installation over a Warming Drawer:

30”

17-1/2”

36-3/4”

Min.

NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven supports
above the Warming Drawer location does not obstruct
the required interior depth and height. See Warming
Drawer installation instructions for details.

23-1/2”

25-1/4”

Construct
solid bottom

- Min. 3/8”
plywood
supported
on all four
sides. Must be
able to support
weight of oven
and contents.

2” Min.
(3” Recommended)

Per Warming
Drawer
Requirement

• Allow 2-1/4” case trim overlap at the
top and 1” overlap on the bottom and 2-1/4” overlap
for each side of the opening.

• Oven overlaps will conceal cut edges on all sides of
the opening.
When installed over a single oven or a warming
drawer, allow at least 2” between the two openings.
This separation will provide clearance for bottom
overlap of the Advantium 120 and the other
appliance overlaps.

• The support must be level and rigidly mounted, flush
with the bottom edge of the cutout.

31-2000354 Rev.0 5

Standard Installation Preparation

PREPARE THE OPENING (CONT.)

Installation over a Wall Oven:

Construct
solid bottom

- Min. 3/8”
plywood
supported
on all four sides.
Must be able to
support weight
of oven and
contents.

2” Min.
(3” Recommended)

Per Oven
Requirement

45-1/4”

Min.

30”

17-1/2”

23-1/2”

25-1/4”

PREPARE THE OPENING (CONT.)

Installation over a Wall Oven and Warming
Drawer:

Construct
Solid Bottom
Min. 3/8”
Plywood
Supported
by
2x4 or 2x2
Runners all
Four Sides

2” Min.
(3” recommended)

Per Oven
Requirement

2” Min.

45-1/4”

Min.

30”

17-1/2”

23-1/2”

25-1/4”

• If you are replacing an electric double oven with the
combined installation of an Advantium Built-In Oven
and a single oven, use the dimensions shown. The
middle rail separating the two openings may need to
be larger than the 2” minimum shown.

Per warming drawer requirement

NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven supports
above the Warming Drawer location does not obstruct
the required interior depth and height. See Warming
Drawer installation instructions for details.

CAUTION

mounting surface must be capable of supporting the
cabinet load, in addition to the added weight of the
oven and drawer, plus additional oven loads.

For personal safety, the

6 31-2000354 Rev. 0

Standard Installation Preparation

PREPARE THE OPENING (CONT.)

Installation over another Advantium Built-In
Oven:

30Ǝ

17-1/2Ǝ

17-1/2Ǝ

23-1/2Ǝ

25-1/4Ǝ

Construct
solid bottom - Min.
3/8” plywood
supported
on all four sides.
Must be able to
support weight
of oven and
contents.

2 1/2Ǝ Min.
(3 1/2Ǝ Recommended)

PREPARE THE OPENING (CONT.)

Installation under a Microwave Oven and over
a Warming Drawer:

Construct

30Ǝ

Per Microwave

Oven Requirement

17-1/2Ǝ

Per Warming
Drawer
Requirement

23-1/2Ǝ

25-1/4Ǝ

solid bottom - Min.
3/8” plywood
supported
on all four sides.
Must be able to
support weight
of oven and
contents.

3.5Ǝ Min.
(4.5Ǝ Recommended)

2Ǝ Min.
(3Ǝ Recommended)

• If you are mounting a GE Appliances Appliances/

Monogram Built-In
use the dimensions
separating the two openings may need to be larger
than the 2Ǝ minimum shown.

Advantoum Oven over another,
shown. The middle rail

NOTE: Additional clearances between the cutouts

may be required. Check to be sure the oven supports
above the Warming Drawer location do not obstruct
the required interior depth and height. See Warming
Drawer installation instructions for details.

CAUTION

mounting surface must be capable of supporting the
cabinet load, in addition to the added weight of the
oven and drawer, plus additional oven loads.

For personal safety, the

31-2000354 Rev.0 7

Standard Installation Preparation

PREPARE THE OPENING (CONT.)

Installation beside another Advantium Built-In
Oven:

• If you are mounting an Advantium Built-In
another, use the dimensions shown. The middle rail
separating the two openings may need to be larger
than the 4-1/2Ǝ minimum shown.

Oven

beside

25-1/4Ǝ

17-1/2Ǝ

23-1/2Ǝ

25-1/4Ǝ

17-1/2Ǝ

4-1/2Ǝ Min.
(5-1/2Ǝ Recommended)

PREPARE THE OPENING (CONT.)

Installation under an Advantium 30Ǝ or 36Ǝ Cooktop or Countertop:

Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for the cutout size.
See the label on top of the oven for approved cooktop models. This oven requires a separate, properly grounded
15-Amp, 120-Volt, 60Hz power supply. The cooktop requires a separate power supply. Use a 36Ǝ or wider base
cabinet.

Cooktop

Cooktop

1-1/2Ǝ Min.

25Ǝ

36Ǝ

Countertop

Height

Ǝ

Cooktop height including depth
of electrical box on some
models. Refer to cooktop
installation instructions.
No minimum clearance required
between cooktop and oven.

23-1/2

4Ǝ High

Toekick

17-1/2

25-1/4Ǝ

Ǝ

8 31-2000354 Rev. 0

Flush Mount Installation Preparation

PREPARE THE INTERIOR

Cut and install side cleats:

• Cut side wood cleats to height of cabinet opening
and approx. 2-1/2” in depth. Install, on each side,
1-3/8” from the front face of the cabinet.

Cut and install bottom cleat:

• Cut bottom wood cleat to a height of 1-1/8”, a depth
of the cabinet minus 1-3/8” and a width of 25-1/4”
to fit between side cleats. Install onto the cabinet
floor between the side cleats, push it all the way
back against cabinet wall and make sure its front face
aligns with the front faces of the side cleats (1-3/8”
gap from the front cabinet face).

A A

C

B

D

E

PREPARE THE OPENING

The Advantium Built-In Oven can be installed
in combination with other Advantium Built-In
ovens. Always follow each product’s Installation
Instructions to complete the installation.

Single Advantium Built-In Oven

Installation:

Cut the opening in a cabinet to the dimensions
shown.

23-1/2” min.

F *

**20 5/8”

Construct
solid bottom

- Min. 3/8”
plywood
supported on
all four sides.
Must be able to
support weight
of oven and
contents.

A Side cleats depth 2-1/2” min.
B Bottom cleat height 1-1/8”
C Bottom cleat depth Cabinet depth minus 1-3/8”
D Bottom cleat width 25-1/4”
E All three cleats 1 1/4”

D

TOP

C

VIEW

A A

Front Face of Cabinet

EE

36-3/4”

Min.

• The support must be level and rigidly mounted,
flush with the bottom edge of the cutout.

Approved Flush Installation

Single Advantium 30” 30-1/4”
Over Warming Drawer 30” 30-1/4”
Over Oven
Over Oven and Warming Drawer
Over Advantium Built-In Oven
Double Advantium (side by side)
Under Cooktop or Countertop See page 10

Dimension F

1/8” Reveal 1/4” Reveal

30” 30-1/4”
30” 30-1/4”
30” 30-1/4”

See page 10

** Top and bottom reveals are set to 1/8”.

31-2000354 Rev.0 9

Flush Mount Installation Preparation

PREPARE THE OPENING

The Advantium Built-In Oven can be installed beside
another Advantium Built-In Oven in a side-by-side

combination.

Double Advantium Built-In Oven

Installation:

Cut the opening in a cabinet to the dimensions shown.

• Center divider acts as cleat for side of each respective
unit. Only one additional side cleat needed per oven
cutout.

• The support must be level and rigidly mounted, flush
with the bottom edge of the cutout.

Dimension 1/8” Reveal 1/4” Reveal

G 59-7/8” 60-1/4”
H 5-1/8” 5-1/4”

I 27-3/8” 27-1/2”

36-3/4”

Min.

23-1/2” min.

G*

H*

I*

I*

20 5/8”

1 1/4”

Construct solid bottom

- Min. 3/8” plywood
supported on all four
sides. Must be able
to support weight of
oven and contents.

PREPARE THE OPENING

Installation under an Advantium 30Ǝ or 36Ǝ Cooktop or Countertop:

Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for the cutout size.
See the label on top of the oven for approved cooktop models. This oven requires a separate from the cooktop,
properly grounded 15-Amp, 120-Volt, 60Hz power supply. Use a 36Ǝ or wider base cabinet.

23-1/2

1-1/2Ǝ Min.

Cooktop

Cooktop

20-5/8”

J*

Ǝ

25Ǝ

36Ǝ

Countertop

Height

Cooktop height including
depth of electrical box
on some models. Refer
to cooktop installation
instructions.
No minimum clearance
required between cooktop
and oven.

*1/8” reveals on
sides and top

4Ǝ High

Toekick

*See table for desired reveals on sides.

Dimension 1/8” Reveal 1/4” Reveal

J 30” 30-1/4”

10 31-2000354 Rev. 0