Cafe CDT866P3MD1 Installation
Installation Instructions
Built-In Dishwasher
If you have questions, visit our website at: cafeappliances.com.
In Canada, visit: cafeappliances.ca
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
WARNING
• To reduce the risk of electric shock, fire, or injury to
persons, the installer must ensure that the dishwasher
is completely enclosed at the time of installation.
• FOR PERSONAL SAFETY: Remove house fuse or
open circuit breaker before beginning installation.
Do not use an extension cord or adapter plug with
this appliance.
• The improper connection of the equipment grounding
conductor can result in a risk of electric shock. Check
with a qualified electrician or service representative if you
are in doubt that the appliance is properly grounded.
• If house wiring is not 2-wire with ground, a ground
must be provided by the installer. When house wiring
is aluminum, be sure to use UL-Listed anti-oxidant
compound and aluminum-to-copper connectors.
CAUTION
Do not remove wood base until you are ready to install
the dishwasher. The dishwasher will tip over when the
door is opened if base is removed.
While performing installations described in this
booklet, gloves, safety glasses or goggles should
be worn.
FOR YOUR SAFETY
Read and observe all WARNINGS and CAUTIONS
shown throughout these instructions.
IMPORTANT – Observe all governing codes and
ordinances.
• Note to Installer – Be sure to leave these instructions
for the consumer’s and local inspector’s use.
• Note to Consumer – Keep these instructions with
your Owner’s Manual for future reference.
• Skill Level – Installation of this dishwasher requires
basic mechanical, electrical and plumbing skills. Proper
installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the Café Warranty. See Warranty
information.
• Completion Time – 1 to 3 Hours. New installations
require more time than replacement installations.
IMPORTANT – The dishwasher MUST be installed to
allow for future removal from the enclosure if service is
required.
Care should be exercised when the appliance is
installed or removed, to reduce the likelihood of
damage to the power supply cord.
If you received a damaged dishwasher, you should
immediately contact your dealer or builder.
Optional Accessories – See the Owner’s Manual for
available custom panel kits.
Your dishwasher is a water heating appliance.
CHECK THE FOLLOWING
Tub trim does not interfere with the door
Dishwasher is square and level at both the top and bottom of the cabinet opening, with no
twisting or distortion of the tub or door
All 4 legs of the dishwasher are firmly in contact with the floor
Drain hose is not pinched between the dishwasher and adjacent cabinets or walls
Tub trim is fully seated on the tub flange
READ CAREFULLY
KEEP THESE INSTRUCTIONS
Printed in the United States
31-4000043 07-18 GEA
Installation Preparation
PARTS SUPPLIED IN
INSTALLATION PACKAGE:
• Junction box cover and #10 hex-head screw
• Hose clamp
• Drain hose (approximately 58” long)
• Drain hose hanger
• 2 #8-18 hex head screws to secure brackets to
washer tub frame
• 1 top trim piece (on some models)
• 2 side trim pieces
• 2 mounting brackets for wood countertops
or side cabinets
• 2 #8-18 x 5/8” Phillips special head screws,
to secure dishwasher to underside of
countertop or to side cabinets
• Plug buttons
• Literature, samples and/or coupons
MATERIALS YOU WILL NEED:
• 90° elbow (3/4”hose internal thread on one
end,opposite end sized to fit water supply)
• UL-listed wire nuts (3)
• Masking Tape
Materials For New Installations Only:
• Air gap for drain hose, if required
• Waste tee for house plumbing, if applicable
• Electrical cable or Power Cord Kit WX09X70910 (5.4 Ft)
or WX09X70911 (7.9 ft) depending on your installation.
• Screw-type hose clamps
• Strain relief for electrical connection
• Hand shut-off valve (recommended)
• Hot Water Line–3/8” minimum, copper tubing
(including ferrule, compression nut) or Café part
WX28X326, flexible braided hose.
• WD24X10065 drain hose (12’ long), if needed.
Junction
Box Cover
Mounting
Brackets
#10
Hex-Head
Junction
Box Screw
1/2" long
Top Trim Piece
(on some models)
#8 Phillips
Head Screws
90°Elbow
Waste Tee
Air Gap
Strain Relief
Drain Hose Hanger
Special
5/8" long
Wire Nuts (3)
Hand
Shut-Off
Valve
Hose Clamp
Plug Buttons
Masking Tape
Electrical Cable
(or Power Cord,
if applicable)
Hot Water Line
Drain Hose
#8 Hex-Head
Mounting Bracket
Screws
Side Trim Pieces
Literature
Coupler for
optional
drain hose
Hose Clamps
Optional
12' Drain Hose
WD24X10065
TOOLS YOU WILL NEED:
• Phillips-head screwdriver
• 1/4” and 5/16” nutdriver
• 6” Adjustable wrench
• Level
• Carpenter’s square
• Measuring tape
• Safety glasses
• Flashlight
• Bucket to catch water when flushing the line
• 15/16” socket (optional for skid removal)
• Gloves
• Pliers
For New Installations Only:
• Tubing cutter
• Drill and appropriate bits
• Hole saw set
Phillips-Head
Screwdriver
Safety Glasses
15/16” Socket
Flashlight
2
1/4” and 5/16”
Nutdriver
6” Adjustable
Wrench
Hole Saw Set
Pliers
Tubing Cutter
Measuring Tape
Drill and Bits
Level
Carpenter’s
Square
Gloves
Bucket
Installation Preparation
PREPARE DISHWASHER ENCLOSURE
This Wall Area
Must be Free
34-1/2”+1/4”
33-1/2” to 34-3/4”
Underside of
Underside of
Countertop
Countertop
to Floor
to Floor
of Pipes and
Wires
Plumbing and Electric Service
Must Enter Inside This Area
24”
Min.
Figure A
• The rough cabinet opening must be at least 24” deep,
24” wide and approximately 34-1/2” high from floor to
underside of the countertop.
• The dishwasher must be installed so that drain hose is
no more than 12’ in length for proper drainage.
• The dishwasher must be fully enclosed on the top,
sides and back, and must not support any part of the
enclosure.
24”
Min.
4”
Cabinets
Square
6”
and
Plumb
WARNING
To reduce the risk of electric shock, fire, or injury
to persons, the installer must ensure that the
dishwasher is completely enclosed at the time of
installation.
Countertop
Dishwasher
25-1/2"
Clearance for Door
Opening 2" Minimum
Figure B
CLEARANCES:
• When installed into a corner, allow 2” min. clearance
between dishwasher and adjacent cabinet, wall or other
appliances. Allow 25-1/2” min. clearance from the front of
the dishwasher for door opening. Figure B.
DRAIN REQUIREMENTS
• Follow local codes and ordinances.
• Do not exceed 12’ distance to drain.
• Drain connection height is not to exceed 72” above
bottom of dishwasher.
NOTE : Air gap must be used if waste tee or disposer
connection is less than 18” above floor to prevent
siphoning.
DETERMINE DRAIN METHOD
The type of drain installation depends on the following
questions.
• Do local codes or ordinances require an air gap?
• Is waste tee less than 18” above floor?
If the answer to either question is YES, Method 1
MUST be used.
•
If the answers are NO, either method may be used.
CABINET PREPARATION
• Drill a 1-1/2” diameter hole in the cabinet wall within
the shaded areas shown in Figure A for the drain hose
connection. The hole should be smooth with no sharp edges.
IMPORTANT – When connecting
drain line to disposer, check to be sure
that drain plug has been removed.
DISHWASHER WILL NOT DRAIN IF
PLUG IS LEFT IN PLACE.
Remove
Drain
Plug
Method 1 – Air Gap with Waste Tee or Disposer
An air gap must be used when required by local codes
and ordinances. The air gap must be installed according to
manufacturer’s instructions.
Figure C
Method 2 – “High Drain Loop” with Waste Tee or Disposer
Drain Hose Hanger
32"
Min.
18"
Min.
Figure D
Drain Hose Hanger
32"
Min.
18"
Min.
Tip: Avoid unnecessary service call charges.
Always be sure disposer drain plug has been removed
before attaching dishwasher drain hose to the disposer.
3
Installation Preparation
PREPARE ELECTRICAL WIRING
WARNING
FOR PERSONAL SAFETY: Remove house fuse or
open circuit breaker before beginning installation. Do
not use an extension cord or adapter plug with this
appliance.
Electrical Requirements
• This appliance must be supplied with 120V, 60 Hz.,
and connected to an individual properly grounded
branch circuit, protected by a 15- or 20-ampere circuit
breaker or time-delay fuse.
• Wiring must be 2 wire with ground and rated for 75°C
(167°F).
• If the electrical supply does not meet the above
requirements, call a licensed electrician before
proceeding.
Alternate Receptacle
Location in Adjacent
Cabinet
18"
1-1/2" Dia. Hole (Max.)
6"
24"
from Wall
Ground
Black
3"
from
Cabinet
White
Figure E
18"
6"
Receptacle
Location
Area
For models equipped with power cord: Do not modify the
plug provided with the appliance; if it will not fit the outlet,
have a proper outlet installed by a qualified technician.
Grounding Instructions–Permanent Connection
This appliance must be connected to a grounded metal,
permanent wiring system, or an equipment-grounding
conductor must be run with the circuit conductors and
be connected to the equipment-grounding terminal or
lead on the appliance.
Grounding Instructions–Power Cord Models
This appliance must be grounded. In the event of a
malfunction or breakdown, grounding will reduce the risk
of electric shock by providing a path of least resistance
for electric current. This appliance is equipped with a
cord having an equipment-grounding conductor and
a grounding plug. The plug must be plugged into an
appropriate outlet that is installed and grounded in
accordance with all local codes and ordinances.
WARNING
The improper connection of the equipment grounding
conductor can result in a risk of electric shock. Check
with a qualified electrician or service representative
if you are in doubt that the appliance is properly
grounded.
Cabinet Preparation & Wire Routing
•
The wiring may enter the opening from either side, rear
or the floor within the shaded area illustrated above in
Figure E and defined in Figure A.
• Cut a 1-1/2" maximum diameter hole to admit the
electrical cable. Edges of hole should be smooth and
rounded. Permanent wiring connections may pass
through the same hole as the drain hose and hot water
line, if convenient. If cabinet wall is metal, the hole
edge must be covered with a bushing.
NOTE:
Power cords with plug must pass through a
separate hole in the cabinet.
Electrical Connection to Dishwasher
Electrical connection is on the right front of dishwasher.
• For permanent connections the cable must be routed
as shown in Figure E. Cable must extend a minimum of
24" from the rear wall.
• For power cord connections, install a 3-prong
grounding type receptacle in the sink cabinet rear wall,
6" min. or 18" maximum from the opening, 6" to 18"
above the floor.
• Use only WX09X70910 or WX09X70911 Dishwasher
Power Cord Kit.
4
Installation Preparation
PREPARE HOT WATER LINE
NOTE: Café recommends copper tubing for the water
line, but if you choose to use flexible hose, use Café
WX28X326, flexible braided hose.
• The water supply line (3/8” copper tubing or flexible
braided hose) may enter from either side, rear or
floor within the shaded area shown in Figure F.
• The water supply line may pass through the same
hole as the electrical cable and drain hose. Or, cut an
additional 1-1/2" diameter hole to accommodate the
water line. If power cord with plug is used, water line
must not pass through power cord hole.
1-1/2”
Shut-off
Valve
Hot
2"
From
Cabinet
Cabinet Face
Dia.
Hole
19" From Wall
2" From Floor
Figure F
4"
6"
Water Line Connection
• If using a flexible braided supply hose, label
the hose with the installation date to use as
reference. Flexible braided hoses, elbows and
gaskets should be replaced in 5 years.
• Turn off the water supply.
• Install a hand shut-off valve in an accessible location,
such as under the sink. (Optional, but strongly
recommended and may be required by local codes.)
• Water connection is on the left side of the
dishwasher. Install the hot water inlet line, using no
less than 3/8” copper tubing or a flexible braided
hose. Route the line as shown in Figure F and
extend forward at least 19” from rear wall.
• Adjust water heater for 120°F to 140°F temperature.
• Flush water line to clean out debris.
• The hot water supply line pressure must be 20-120
PSI.
CAUTION
Do not remove wood base until you are ready to
install the dishwasher. The dishwasher will tip over
when the door is opened if base is removed.
Turn page to begin dishwasher
installation.
5
Dishwasher Installation
STEP 1
PREPARATION
Locate the items in the installation package:
• Screws
• Junction box cover
• Drain hose and clamp
• Mounting brackets
• Trim pieces (on some models)
• Drain hose hanger
• Owner’s Manual
• Product samples and/or coupons
STEP 2
NOTE: If installing a
Custom Door Panel
(available on some
models), please
follow the instructions
found in the Custom
Door Panel kit
WD35X20417.
• With dishwasher
on the wood base,
check the door
balance by opening
and closing the door.
• Door is properly balanced if, when opened, it self
closes within 20° from vertical, stays in position from
20° to 70° and falls fully open beyond 70°.
• If necessary increase or decrease tension as shown.
Some models will have 2 springs on one side and
1 spring on the other side. Latch door and adjust
springs to correct balance.
CHECK DOOR BALANCE
Door
closes
within
20°
Door stays in
position from
20° to 70°
Door falls fully
open beyond 70°
Side View
Figure G
Figure G
Spring
hooked
to hole
inside rail
STEP 3
REMOVE WOOD BASE,
INSTALL LEVELING LEGS
IMPORTANT – Do not kick off wood base!
Damage will occur.
• Move the dishwasher close to the installation location
and lay it on its back. NOTE: Do not place the
dishwasher on its side.
• Remove the 4 leveling legs on the underside of the
wood base with a 15/16” socket wrench.
• Discard base.
• Screw leveling legs back into the dishwasher frame,
approximately 1/2” from frame as shown.
Approx
1/2"
Figure I
NOTE: Some models have rear adjustable leveling
wheels, and will not require the 2 rear leveling legs.
STEP 4
• Remove the 2 toekick screws and toekick. Set aside
for use in Step 23.
REMOVE TOEKICK
Side View
Increase
Tension
Decrease
Tension
NOTE: The number of
springs, on each side,
will vary by model.
Figure H
Make sure pully
cables are within
pulley shoulders
Custom
door
panel
Front View
Tip: Make sure door opens and closes smoothly.
Check door opening and closing. If door does not open
easily or falls too quickly, check spring cable routing.
The cable is held in place by “shoulders” on the pulley.
Check to be sure cable has not slipped over the pulley
shoulders and is routed as shown.
Toekick
Remove 2
Figure J
Toekick Screws
6
Dishwasher Installation
STEP 5
IF NECESSARY, REMOVE
FLOOR PROTECT PAN
• Disconnect leak sensor wire
(on some models).
• Pull floor protect pan forward and
slide it from under the dishwasher.
• Set aside for use in Step 21.
STEP 6
• Thread 90° elbow
onto the water valve.
Ensure rubber gasket
is located between
valve and elbow.
• Do not overtighten
elbow. Water valve
bracket could bend
or water valve fitting
could break.
• Position the end
of the elbow to
face the rear of the
dishwasher.
STEP 7
INSTALL 90° ELBOW
Water
Valve
Bracket
INSTALL DRAIN HOSE TO
Squeeze connector at top
to release snap feature
Leak Sensor
Floor Protect Pan
Figure L
Front of dishwasher
90° Elbow
Fill Hose
Figure M
DRAIN LOOP
Connect drain loop end to drain hose using the screw
clamp as shown in the figure.
STEP 8
POSITION WATER LINE
AND HOUSE WIRING
• Position water supply line and house wiring on the
floor of the opening to avoid interference with base
of dishwasher and components under dishwasher.
4"
6"
STEP 9
4"
6"
Water
Line
Figure O
INSTALL DRAIN HOSE,
House
Wiring
THROUGH CABINET
• Position dishwasher in front of cabinet opening,
and if present, dislodge drain hose from drain hose
clip. Insert drain hose into the hole in cabinet side.
If a power cord is used, guide the end through a
separate cabinet opening.
Pull insulation
blanket over
collar
House
Wiring
Power Cord
(If used)
Water Line
Ensure drain hose is
not twisted or pinched
Maximum drain hose
length is 15'
Do not disconnect or remove
high drain loop from left side
of dishwasher
Drain
Hose
Insulation
Blanket
Figure P
Figure N
NOTE: The high drain loop on the side of the tub is
designed for better wash performance. Do not remove
from the side of the tub.
Tip: Prevent unnecessary service call charges for
fill, drain or noise concerns.
Position utility lines so they do not interfere with
anything under or behind the dishwasher.
7
Dishwasher Installation
STEP 10
SLIDE DISHWASHER
THREE-FOURTHS OF
THE WAY INTO CABINET
IMPORTANT – Do not push against front panel with
knees. Damage will occur.
• Grasp the sides of the front panel and slide
dishwasher into the opening a few inches at a time.
Do not push against
front door panel with
knee. Damage to the
door panel will occur.
• As you proceed, pull the drain hose through the
opening under the sink. Stop pushing when the
dishwasher extends about 6 inches forward of
adjacent cabinets.
• Make sure drain hose is not kinked under or behind
the dishwasher.
• Make certain the house wiring, drain line and
water line do not interfere with components under
dishwasher.
Figure Q
STEP 11
In this step you will need the trim pieces set aside in Step 1.
Top Trim
Side Trim
Top
View
INSTALL TRIM PIECES
Side
Trim
Top View
Figure R
Fully seat to tub flange
Tub frame
Tub trim
Door
Handle
Side
Trim
• Select the top trim piece (See Figure R) and line up
center to the top latch. Press the trim piece onto the
tub flange moving from one side to the other.
• Select the left trim piece (see Figure R). Align top
edge with the top trim and press it onto the left side
of the tub flange moving from the top to the bottom.
Repeat for the right side tub flange trim piece. (See
Figure R for right side trim piece.)
8
Dishwasher Installation
STEP 12
INSTALL MOUNTING
BRACKETS
You will need the mounting brackets and 2 #8 hexhead screws set aside in Step 1.
You must install the mounting brackets onto the
dishwasher tub frame top or sides prior to sliding
the dishwasher into place under the countertop. This
dishwasher is capable of a true-flush installation at a
24” deep opening. The mounting brackets have several
available attachment positions to accommodate different
cabinet constructions.
Install mounting brackets on top if the
underside of countertop is wood or wood-like
material that accepts screws:
IMPORTANT - After installing brackets and before
closing the dishwasher door, adjust the brackets
by bending them up as needed, so that they do not
contact the top of the dishwasher door and cause
damage.
Top Mounting
STEP 12
INSTALL MOUNTING
BRACKETS (CONT.)
Install mounting brackets on sides if the
countertop is granite or similar material that will
not accept wood screws:
• If present, remove drain hose clip from collar and
dispose.
• Break off front portion of the tab with pliers at the
location shown prior to attaching to dishwasher.
• Position the left-hand side bracket as shown. Attach
the bracket to the tub frame with the #8 screw through
the slotted hole below the round hole. Repeat with the
right bracket.
Tub
Side Mounting
Dishwasher
tub frame
Do not pinch the
latch wires in #8
bracket screw
#8 Bracket
screw as
supplied
Front
Care should be taken
to ensure mounting
screws do not damage
cabinetry
Bend and break
here if necessary
#8 Bracket
Screw
Bend and break here
after installing if counter
Dishwasher
tub frame
• If you are installing the dishwasher under a counter
with a short overhang, the countertop brackets may
extend beyond the edge of the counter. If this is
the case, remove the excess length by repeatedly
bending the brackets at the front notch only until they
break.
has a short overhang.
Tub
Front
Bracket
Figure S
Bracket
Remove
this clip
STEP 13
PUSH DISHWASHER
Figure T
INTO FINAL POSITION
• Check the tub insulation blanket, if equipped, to be
sure it is smoothly wrapped around the tub. It should
not be “bunched up” and it must not interfere with
the door springs. If the insulation is “bunched up” or
interfering with the springs, straighten and re-center
the blanket prior to sliding the dishwasher into its
final position.
• Slide the dishwasher into the final position by
pushing on the sides of the door panel. Do not push
or pull the door in a partially open or closed position
when moving the dishwasher. Do not use a knee or
push on the center of the panel. If you do, damage to
the panel will likely result. Check that the dishwasher
is squarely positioned in the cabinet opening at
both the top and the bottom of the appliance prior to
mounting to the cabinet.
IMPORTANT – Before opening the dishwasher door,
be certain the edges of the dishwasher door panel
are behind the face of the adjacent cabinet and not
up against the cabinet face. Refer to Figure U. If the
dishwasher door is opened when the edge of the door
is against the face of the cabinet, dishwasher door
damage and cabinet damage will occur.
9
Dishwasher Installation
STEP 13 STEP 14
PUSH DISHWASHER
INTO FINAL POSITION
(CONT.)
• Open and close the dishwasher door to be sure it
operates smoothly, and does not rub on the adjacent
cabinet.
Tip: Prevent unnecessary service charges for
panel damage or wash performance.
Check dishwasher alignment prior to opening
dishwasher door to prevent panel damage.
Make sure utility lines are not trapped or crushed behind
dishwasher. Crushed lines will restrict water flow.
Door
Fits and
Swings
Back
Behind
Cabinet
Frame
Correct
Alignment
Figure U
Check that tub trim does not
contact the door at all points
Top
View
Tub trim may be trimmed if
necessary to ensure proper
door operation
STEP 14
IMPORTANT – Dishwasher must be level for proper dish
rack operation, wash performance and door operation. The
dishwasher must be leveled left to right and front to back.
This ensures the dish racks will not roll in or out on their own,
circulation water will flow to the pump inlet, and the door will
close without hitting the side of the tub.
Incorrect Alignment
will result in door damage
Tub frame
Tub trim
Cabinet
Door
Handle
LEVEL DISHWASHER
Door Catches
on Cabinet Frame
Do not allow tub trim to get
trapped by or come into
contact with the door
Top
View
Tub trim
trapped
by door!
• Remove the lower dish
rack and place a level on
the door and lower rack
track as shown in Figure V.
• If your model has rear
wheels, the height of the
wheels are adjusted from
the front of the dishwasher
along with the 2 front
legs on the bottom of the
dishwasher. Begin the
leveling process with the
front legs by individually
turning the front 2 legs.
By adjusting the front
legs first,access to the
rear leveling bolts
is maximized
easing rear wheel
adjustment. When
the front legs are
adjusted to a height
resulting in an
appropriate gap to
the upper cabinet,
proceed to adjust
the rear leveling
wheels by adjusting
the leveling bolts as illustrated in Figure W. Individually turn
the 2 bolts to adjust the rear wheels. Slowly rotate the 2 bolts
counter clockwise to raise the back of the dishwasher, and
clockwise to lower it. Continue to adjust the feet and wheels
until the dishwasher is level as illustrated in Figure W. Ensure
all 4 legs/wheels are firmly in contact with the floor.
• If your model has
4 leveling feet,
adjust the level of
the dishwasher by
individually turning the
4 legs on the bottom
of the dishwasher as
shown in Figure WW.
• The dishwasher
is properly
leveled when the
level indicator is
centered left to right and front to back. Also, the dishwasher
door should close without hitting the side of the tub.
• Replace the lower rack.
• Pull each rack out, about halfway. Check to be sure it does
not roll back or forward on the door. If the rack moves,
adjust leveling legs.
Tip: Prevent unnecessary service charges. Verify
dishwasher is leveled.
Pull the dish racks half way out. They should stay put. Open
and close the door. The door should fit in the tub opening
without hitting the side of the tub. If the racks roll on their
own, or the door hits the side of tub, re-level the dishwasher.
LEVEL DISHWASHER
(CONT.)
Figure V
Adjust
Figure W
Figure WW
Adjust
10
Dishwasher Installation
STEP 15
POSITION DISHWASHER,
SECURE TO
COUNTERTOP OR
CABINET
In this step you will need the 2 Phillips special head
screws from the screws set aside in Step 1.
The dishwasher must be secured to the countertop
or the cabinet sides. When the underside of the
countertop is wood, use Method 1. Use Method 2
when the underside of the countertop is made of a
material, such as granite, that will not accept wood
screws.
IMPORTANT – Prevent door panel and control
panel damage. Dishwasher must be positioned so
the front panel and control panel do not contact the
adjacent cabinets or countertop. Mounting screws
must be driven straight and flush. Protruding screw
heads could scratch the door panel or control panel
and interfere with door operation.
Method 1
Secure dishwasher to underside of wood countertop.
• Recheck alignment of the dishwasher in the cabinet.
Refer to Steps 13 and 14. Door panel and/or control
panel must not hit cabinets or countertop.
• Fasten the dishwasher to the underside of the
countertop with the 2 Phillips special head screws.
Refer to figure. Make certain screws are driven
straight and flush to prevent panel damage.
Brackets
Wood Countertop
STEP 15
POSITION DISHWASHER,
SECURE TO COUNTERTOP
OR CABINET (CONT.)
• Re-check that the dishwasher is square and level at
both the top and bottom of the cabinet opening, with no
twisting or distortion of the tub or door after mounting to
the cabinets/countertop. Adjust if necessary.
• Confirm all leveling legs are in contact with the floor
to prevent the dishwasher from rocking and ensure
proper door and latch operation.
STEP 16
CONNECT WATER
SUPPLY
Connect water supply line to 90° elbow.
If using a flexible braided hose connection:
• Attach nut to 90° elbow using an adjustable wrench.
If using a copper tubing connection:
• Slide compression nut, then ferrule over end of water
line.
• Insert water line into 90° elbow.
• Slide ferrule against elbow and secure with
compression nut.
IMPORTANT – Check to be sure that door spring and/
or door spring cable do not rub or contact the fill hose
or water supply line. Test by opening and closing the
door. Re-route the water supply lines if a rubbing noise
or interference occurs.
Hot Water
90° Elbow
Supply Line
Compression
Nut
Method 2
Secure dishwasher to cabinet sides.
• Recheck alignment of the dishwasher in the cabinet.
Refer to Steps 13 and 14. Door panel and/or control
panel must not hit cabinets or countertop.
• Remove plug buttons. Do not discard.
• Fasten the dishwasher to the adjacent cabinets with
the 2 Phillips special head screws provided. Refer
to Figure X. Make certain screws are driven straight
and flush to prevent panel damage. Do not screw
into the cabinet face frame.
• Install plug buttons to the side of the tub in the holes
provided.
Solid Surface Countertop
Screw
Plug buttons
Side Brackets
Screw
Figure X
11
Bottom Left Side
Ferrule
Figure Y
Dishwasher Installation
STEP 17 STEP 17
The molded end of the drain hose will fit 5/8” through 1”
diameter inlet ports on the air gap, waste tee or disposer.
• Determine size of inlet port.
• Cut drain hose connector on the marked line, if required,
to fit the inlet port.
Figure Z
• If a longer drain hose is required, replace the provided
user bag drain hose with Café part WD24X10065, a
12’ long hose which can be connected directly to the
drain loop already attached to the unit (see Step 7). If
service part hose is not available, an additional hose
with coupler, ID of 5/8” or 7/8” and no longer than
66”, may be attached to the provided user bag drain
hose. Secure the connection with hose clamps to the
provided user bag drain hose.
CONNECT DRAIN LINE
Cutting Line
1"
IMPORTANT: Do not cut corrugated
5/8"
portion of hose
• Connect drain line to air gap, waste tee or disposer
using the previously determined method. Secure
hose with a screw-type clamp.
Method 1 – Air gap with waste tee or disposer
Waste Tee Installation
Method 2 – “High drain loop” with waste tee or
disposer
With this method you will need the drain hose hanger
set aside in Step 1.
Fasten drain hose to underside of countertop with the
provided hanger.
CONNECT DRAIN LINE
(CONT.)
Disposer Installation
Figure AB
Hose
Figure AA
NOTES:
• DRAIN CONNECTION HEIGHT IS NOT TO EXCEED
72” ABOVE BOTTOM OF DISHWASHER.
• TOTAL DRAIN HOSE LENGTH MUST NOT
EXCEED 12 FEET FOR PROPER DRAIN
OPERATION.
Clamp
Coupler Hose
Clamp
Drain Hose Hanger
32"
Min.
18"
Min.
Waste Tee Installation
Figure AC
IMPORTANT – When connecting drain line to
disposer, check to be sure that drain plug has been
removed. DISHWASHER WILL NOT DRAIN IF PLUG
IS LEFT IN PLACE.
Disposer Installation
18"
Min.
32"
Min.
Remove
Drain
Plug
Tip: Avoid unnecessary service call charges for a
no drain complaint.
Make sure excess drain hose has been pulled through
the cabinet opening. This will prevent excess hose
in the dishwasher cavity from becoming kinked or
crushed by the dishwasher.
12
Dishwasher Installation
STEP 18
CONNECT POWER SUPPLY
If a power cord with plug is already installed
proceed to Step 19.
WARNING
If house wiring is not 2-wire with ground, a ground
must be provided by the installer. When house wiring
is aluminum, be sure to use UL-Listed anti-oxidant
compound and aluminum-to-copper connectors.
In this step you will need the junction box cover and
the #10 Hex head screw from the screws set aside in
Step 1.
• Secure house wiring to the back of the junction box
with a strain relief.
• Locate the 3 dishwasher wires, (white, black and
green) with the stripped ends coming out of the AC
jumper. Use UL listed wire nuts of appropriate size to
connect incoming ground to green, white to white and
black to black.
• Install the junction box cover using #10 hex head
screw. Check to be sure that wires are not pinched
under the cover.
• Make sure that the junction box cover is resting on
the mounting bracket.
• If using a Power Cord Kit, use Café part number
WX09X70910 or WX09X70911 and refer to the
included instructions.
NOTE: Do not remove the
Junction Box Bracket.
White
Ground
(Green)
AC
Jumper
STEP 19
Review this list after installing your dishwasher to
avoid charges for a service call that is not covered
by your warranty.
• Check to be sure power is OFF.
• Open door and remove all foam and paper
packaging.
• Locate the Owner’s Manual set aside in Step 1.
• Read the Owner’s Manual for operating instructions.
• Check door opening and closing. If door does not
open and close freely, check for proper routing of
spring cable over pulley. If door drops or closes
when released, adjust spring tension. See Step 2.
• Check to be sure that wiring is secure under the
dishwasher, not pinched or in contact with door
springs or other components. See Step 18.
• Check door alignment with tub. If door hits tub, level
dishwasher. See Step 14.
• Check door alignment with cabinet. If door hits
cabinet, reposition dishwasher. See Step 13.
• Check that door spring does not contact water line,
fill hose, wiring or other components. See Step 13.
• Verify water supply and drain lines are not kinked
or in contact with other components. Contact with
motor or dishwasher frame could cause noise.
• Turn on the sink hot water faucet and verify water
temperature. Incoming water temperature must be
between 120°F and 140°F. A minimum of 120°F
temperature is required for best wash performance.
See “Prepare Hot Water Line,” page 5.
• Add 1 quart of water to the bottom of the dishwasher
to lubricate the pump seal.
• Turn on water supply. Check for leaks. Tighten
connections if needed.
• Remove protective film if present from the control
panel and door.
• Check that tub trim does not contact the door.
PRETEST CHECKLIST
Black
Ground Screws
Figure AD
NOTE: All ground screws, brackets and wires must
remain intact.
Junction Box
Bracket
13
Dishwasher Installation
STEP 20 STEP 21
• Turn on power supply or plug power cord into outlet,
if equipped.
• Select a cycle to run and push the START button.
• Ensure the door is latched. Dishwasher should start.
• Check to be sure that water enters the dishwasher.
If water does not enter the dishwasher, check to be
sure that water and power are turned on.
• Check for leaks under the dishwasher. If a leak
is found, turn off power at the breaker, and then
tighten water connections. Restore power after leak
is corrected.
• Check for leaks around the door. A leak around
the door could be caused by door rubbing or
hitting against adjacent cabinets. Reposition the
dishwasher if necessary. See Step 13.
• Press and hold the START button for 3 seconds to
cancel the cycle. The unit will begin to drain. Check
drain lines. If leaks are found, turn off power at the
breaker and correct plumbing as necessary. Restore
power after corrections are made. See Steps 7, 8, 9,
10 and 17.
• Open dishwasher door and make sure all of the
water has drained. If not, check that disposer plug
has been removed and/or air gap is not plugged.
Also check drain hose to be sure it is not kinked
underneath or behind dishwasher. See Step 17.
• Press START button once again and run dishwasher
through another cycle. Check for leaks and correct if
required.
• Repeat these steps as necessary.
DISHWASHER WET TEST
• Slide the floor protect pan under the dishwasher
until its side lock slots are close to engaging the side
mounting tabs on the dishwasher.
• Lift the pan until its lock slots contact the mounting
tabs and push the pan back to engage them.
Rear
Floor Protect
Pan
REPLACE FLOOR
PROTECT PAN
Figure AE
Mounting Tab
Two on each side
of the dishwasher
Two on each side of
the floor protect pan
Floor Protect
Pan
Lock Slots
Front
• When properly installed, the top of the lock slots will
be over the mounting tabs.
Mounting
Ta b
Lock Slot
• Connect the leak sensor connector to the leak sensor
(on some models).
Leak Sensor
(on some models)
14
Dishwasher Installation
STEP 22 STEP 22
POSITION SOUND
INSULATION PIECE
• Locate the sound insulation package inside the
dishwasher.
• Stand the parts upright as shown.
Dishwasher
Door
Toekick
Figure AF
• Locate the control box.
Insulation Block
(On some models.)
Control Box
• Open door all the way, if the door doesn’t stay fully
open, adjust the insulation panel.
• Align the screw holes with the screw holes on the
legs of the dishwasher.
• Ensure vent opening is not blocked by insulation.
Vent opening should be properly
aligned with cutout in the insulation
STEP 23
• Place toekick against the legs of the dishwasher.
POSITION SOUND
INSULATION PIECE
(CONT.)
REPLACE TOEKICK
Figure AG
• Push insulation block portion under the dishwasher
until it is beneath the control box.
Figure AH
• Push the panel portion up to the front of the block.
(on some models)
Push the sides of the insulation behind
the toekick attachment screw holes
• Tuck the sides of the front panel behind the toekick
attachment screw holes.
Toekick
Figure AJ
Attachment
Screws
• Align the toekick with the bottom edge and make
sure it is against the floor.
• Insert and tighten the 2 toekick attachment screws.
The toekick should stay in contact with the floor.
Tip: Reduce sound from under the dishwasher.
Make sure toekick is against floor.
STEP 24
• Tub trim does not interfere with the door
• Dishwasher is square and level at both the top and
bottom of the cabinet opening, with no twisting or
distortion of the tub or door
• All 4 legs of the dishwasher are firmly in contact with
the floor
• Drain hose is not pinched between the dishwasher
and adjacent cabinets or walls
• Tub trim is fully seated on the tub flange
CHECK THE FOLLOWING
STEP 25
• Be sure to leave complete literature package, these Installation
Instructions and product samples and/or coupons with the
consumer.
LITERATURE
15
Loading...