Owner's Manual
Dishwashers
Models: CDT706 Series & CDT836-866 Series
Contents
Safety Information ...............................4
Using the Dishwasher
Getting Started .................................6
Dispensers ...................................10
Appliance Communication .......................12
Loading .....................................13
Care and Cleaning ..............................20
Troubleshooting Tips ...........................22
Limited Warranty ...............................25
Consumer Support .............................26
Write the model and serial numbers here:
Model # _______________________________
Serial # _______________________________
You can find them on a label on the tub wall just
inside the door.
English • Français • Español
49-4000042 06-18 GEA
THANK YOU FOR MAKING CAFÉ A PART OF YOUR HOME.
We take pride in the craftsmanship, innovation and design that goes into every Café product, and
we think you will too. Among other things, registration of your appliance ensures that we can deliver
important product information and warranty details when you need them.
Register your Café appliance now online. Helpful websites are available in the Consumer Support
section of this Owner’s Manual. You may also mail in the pre-printed registration card included in the
packing material.
2 49-4000042
Notes
WELCOME
49-4000042 3
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
WARNING
For your safety, the information in this manual must be followed to minimize
the risk of fire, explosion, electric shock, and to prevent property damage, personal injury,
or death.
WARNING
This dishwasher must be properly installed and located in accordance with the Installation Instructions before
it is used. If you did not receive an Installation Instructions sheet with your dishwasher, you can receive one by
visiting our website at cafeappliances.com. In Canada, visit cafeappliances.ca.
Ŷ
SAFETY INFORMATION
Connect the dishwasher/appliance to a grounded
metal, permanent wiring system; or run an
equipment-grounding conductor with the circuit
conductors and connect to the equipment-grounding
terminal or lead of the appliance.
Ŷ
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
Check with a qualified electrician or service
representative if you are in doubt whether the
appliance is properly grounded.
Ŷ
Dispose of discarded appliances and shipping or
packing material properly.
PROPER INSTALLATION AND MAINTENANCE
Ŷ
Do not attempt to repair or replace any part of your
dishwasher unless it is specifically recommended in
this manual. All other servicing should be referred to
a qualified technician.
Ŷ
Use only cord kit WX09X70910 or hard-wire to
building electrical. Failure to follow this instruction,
could result in risk of fire and personal injury.
Ŷ
To minimize the possibility of electric shock,
disconnect this appliance from the power supply
before attempting any maintenance.
NOTE: Turning the dishwasher off does not
disconnect the appliance from the power supply.
We recommend having a qualified technician
service your appliance.
WARNING
WHEN USING YOUR DISHWASHER, FOLLOW BASIC PRECAUTIONS,
INCLUDING THE FOLLOWING:
Ŷ
Use this appliance only for its intended purpose as
described in this Owner’s Manual.
Ŷ
Use only detergents or wetting agents
recommended for use in a dishwasher and keep
them out of reach of children. Using a detergent
that is not specifically designed for dishwashers will
cause the dishwasher to fill with suds.
Ŷ
Locate sharp items so that they are not likely to
damage the door seal.
Ŷ
Load sharp knives with the handles up to reduce
the risk of cut-type injuries.
Ŷ
Do not wash plastic items unless marked
dishwasher safe or the equivalent. For plastic
items not so marked, check the manufacturer’s
recommendations.
READ AND SAVE THESE INSTRUCTIONS
Ŷ
Do not touch the heating element during or
immediately after use.
Ŷ
Do not operate your dishwasher unless all
enclosure panels are properly in place.
Ŷ
Do not tamper with controls.
Ŷ
Do not abuse, sit on or stand on the door or dish
rack of the dishwasher.
Ŷ
To reduce the risk of injury, do not allow children to
play with, on or inside this appliance at any time.
Ŷ
Do not store or use combustible materials including
gasoline or other flammable liquids or vapors in the
vicinity of this or any other appliance.
Ŷ
Small parts, such as rack clips and filter retaining
posts, can be a choke hazard to small children if
removed from the dishwasher. Keep out of reach of
small children.
4 49-4000042
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
SAFETY INFORMATION
WARNING
Under certain conditions, hydrogen gas may be produced in a water heater that has not been used for two or more weeks.
HYDROGEN GAS IS EXPLOSIVE.
If the hot water has not been used for two or more weeks, prevent the possibility of damage or injury by turning
on all hot water faucets and allowing them to run for several minutes. Do this before using any electrical
appliance connected to the hot water system. This simple procedure will allow any built-up hydrogen gas to
escape. Since the gas is flammable, do not smoke, use an open flame, or use the appliance during this process.
WARNING
PROPER DISPOSAL OF THE DISHWASHER
Junked or abandoned dishwashers are dangerous…even if they will sit for “just a few days.”
If you are getting rid of your dishwasher, please follow the instructions below to help prevent
accidents.
Ŷ
Do not allow children to play with, on, or inside this or any discarded appliance.
Ŷ
Take off the door of the washing compartment or remove the latch by removing the two
screws from the latch receiver inside the tub (as shown).
CAUTION
Ŷ
During or after wash cycle, contents may be hot to
the touch. Use care before handling.
Ŷ
Close supervision is necessary if this appliance is
used by or near children. Do not allow children to
play around the dishwasher when closing the door,
closing the upper rack, or while vertically adjusting
the upper rack due to the possibility of small fingers
being pinched.
WATER HEATER SAFETY
RISK OF CHILD ENTRAPMENT
TO PREVENT MINOR INJURY AND PROPERTY DAMAGE
Ŷ
Non-Dishware Items: Do not wash items such as
electronic air cleaner filters, furnace filters and
paint brushes in your dishwasher. Damage to the
dishwasher and discoloration or staining of the
dishwasher may result.
Ŷ
Load light-weight, plastic items so they do not
become dislodged and drop to the bottom of the
dishwasher—they might come into contact with the
heating element and be damaged.
Two screws
CAUTION
Ŷ
This appliance must be supplied with 120V, 60 Hz,
and connected to an individual, properly grounded
branch circuit, protected by a 15 or 20 amp circuit
breaker or time-delay fuse.
ELECTRICAL REQUIREMENTS
Ŷ
Ŷ
If the electric supply provided does not meet the
above specifications, it is recommended that a
licensed electrician install an approved outlet.
Your dishwasher circuit should not be used for any
other appliance while the dishwasher is in operation as
the dishwasher requires the full capacity of the circuit.
NOTICE
Ŷ ,I\RXUGLVKZDVKHULVFRQQHFWHGWRDZDOOVZLWFK
ensure that the switch is on prior to use.
Ŷ ,I\RXFKRRVHWRWXUQWKHZDOOVZLWFKRIIEHWZHHQ
wash cycles, allow 5-10 seconds after turning the
switch on before touching Start to allow the control
to initialize.
Ŷ 8VHRQO\SRZGHUFinish® Quantum® Automatic
Dishwashing Detergent, liquid detergents or rinse
agents recommended for use in a dishwasher and
keep them out of the reach of children. Finish
Quantum®Automatic Dishwashing Detergent,
and Finish
been approved for use in all Café dishwashers.
®
Jet-Dry®Rinse Aid rinse agents have
®
READ AND SAVE THESE INSTRUCTIONS
49-4000042 5
Getting started
Features and appearance will vary throughout this manual
CDT706 and
CDT836 Series
CDT866 Series
Steam
Leak Protection
If a leak is detected, the dishwasher will drain and the cycle will stop. The display will show “LEAK DETECTED”.
Contact Café for service.
Load Dishwasher
1
USING THE DISHWASHER
For best dishwashing results, follow the loading guidelines found in the Loading section. No pre-rinsing of
normal food soil is required. Scrape off hard soils, including bones, toothpicks, skins, and seeds. Remove
leafy vegetables, meat trimmings, and excessive amounts of grease or oil.
Add Detergent
2
Add needed amount of detergent to the detergent dispenser. Use detergent such as Finish® Quantum
Automatic Dishwashing Detergent. See Dispensers section.
Add Rinse Agent
3
Add rinse agent such as Finish® Jet-Dry®Rinse Aid to the rinse agent dispenser. See Dispensers section.
®
6 49-4000042
Getting started
Select Cycle
4
Press the Select Cycle button for the desired wash cycle. On some models, the light next to the Select Cycle
button will be lit to indicate which wash cycle has been selected. On other models, pressing the Select Cycle
button will show various cycles in the display window. Press the button until the desired cycle is shown.
NOTE: Actual cycle times vary based on soil level, water temperature, and options selected.
The cycle may be selected with the door in the open position. The cycle will not start until the Start button is
pushed and the door is closed within 4 seconds.
AutoSense This cycle automatically senses the soil level and adjusts the wash cycle accordingly. *Time
range: 1 hour 50 minutes - 2 hours 10 minutes.
Heavy This cycle is meant for heavily soiled dishes, cookware, pots, or pans with dried-on or baked-on
soils. Everyday dishes are safe to be used in this cycle. *Time: 2 hours 31 minutes.
Normal This cycle is meant for daily, regular, or typical use to completely wash a full load of normally
soiled dishes and is designed to conserve both water and energy. *Time range: 1 hour 15
minutes - 1 hour 50 minutes. NOTE: Normal was used to rate the energy efficiency of this
dishwasher.
Light This cycle is for light to medium soiled dishes. It is safe for china and crystal with no options
selected. *Time: 55 minutes.
Rinse
(on some
models)
Express
(on some
models)
eWash
(on some
models)
For rinsing partial loads that will be washed later. Do not use detergent. Detergent is not
dispensed during the rinse cycle. *Time: 16 minutes.
This cycle will quickly wash lightly soiled dishes. *Time: 32 minutes. For faster drying, select
Heated Dry or Power Dry. The final rinse temperature will be increased. Heated Dry or Power
Dry will add 15 to 50 minutes to the cycle time. When the Clean light comes on, open the door,
pull the racks out, and the dishes will “flash” dry in approximately five minutes.
This cycle will efficiently wash dishes using about 2 gallons of water and .8 KWhr. Selecting
Power Dry with this cycle adds an energy efficient 50 to 90 minute dry period. Drying is
accomplished with an efficient 2 watt fan.
*Time: 1 hour 3 minutes.
*Washing time only. Does not include drying time, Auto Hot Start, or options. NOTE: If the
incoming water temperature is too low, the Auto Hot Start feature may add up to 11 minutes of
additional time.
USING THE DISHWASHER
49-4000042 7
Getting Started
Select Options
5
The light by the selected button will be lit to indicate which Option has been selected.
Normal
Temp
Wash
Temp
Boost or
Boost
Temp
Wash
Temp Sani
or Sanitize
Temp
USING THE DISHWASHER
Heated or
Power Dry
Off
Heated or
Power Dry
On
Steam
(Prewash)
(on some
models)
Pre Soak
(on some
models)
Wash
Zones
(on some
models)
Bottle Jets
(on some
models)
Delay
Hours
Control
Lock
This option is for normally soiled dishes, optimizes wash performance while conserving energy.
This option increases the temperature to help clean heavily soiled dishes and will increase the
cycle time by 20 to 50 minutes. Option may be turned On or Off during the wash cycle. This
option will also improve dry performance on the Normal cycle.
This option raises the water temperature in the final rinse to sanitize your dishware but may
increase cycle time by 60 minutes. The cycle length will vary depending on the temperature of
your inlet water.
NOTE: This option is monitored for sanitization requirements. If the cycle is interrupted during
or after the main wash portion or if the incoming water temperature is so low that adequate
water heating cannot be achieved, the sanitizing conditions may not be met. In these cases,
the Sanitized or Cycle Sanitized light will not illuminate at the end of the cycle. Utilizing this
option will modify the cycle to meet the requirements of Section 6, NSF 184 for soil removal and
sanitization efficacy.
NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.
Shuts off the drying option. Dishes air dry naturally and energy is saved. Open the dishwasher
door to speed drying.
Turns on the option for faster drying. This option may add up to 85 minutes to the cycle time.
On models with the hidden heater feature, this option boosts the temperature of the dishwasher
during the final rinse portion of the cycle then utilizes a fan to circulate air to dry the dishes. This
very efficient fan may run for an additional 90 minutes after the cycle is complete to maximize
drying performance. Fan operation will end if the door is opened during this 90 minute period.
This option is not available with the Rinse cycle.
For use with heavily soiled and/or dried-on, baked-on soils. This option MUST be selected
PRIOR to starting the cycle. The Steam option adds up to 30 minutes to the cycle time. This
option is available with Heavy, AutoSense, and Normal cycles.
Use this option to improve wash performance with heavy or dried-on soils. This option is
available on Heavy, AutoSense, and Normal cycles and may add up to 30 minutes to the cycle
time.
Selecting either the Upper or Lower Wash Zones will target dishwashing of just one rack. This
will shorten the cycle time and conserve energy. This option should be used when dishes are
placed in only one rack.
This option increases the time that the bottle jets are on and may add up to 23 minutes to the
cycle time. Use this to wash difficult to clean, dishwasher safe baby bottles, sport bottles, tall
coffee cups, etc. See use recommendations in the
Delays the start of a wash cycle up to 8 to 12 hours depending on model. Press Delay Hours, to
select the number of hours, then press Start
cycle will start once allotted time has expired.
You can lock the controls to prevent selections from being made. You can also lock the
controls after you have started a cycle to prevent cycle changes. For example, children cannot
accidentally start the dishwasher by pressing buttons with this option selected.
To LOCK the dishwasher control, depending on the model, press and hold the 1 or 2 buttons
indicated on the controls for 3 seconds. On some models, it will be the Heated Dry, another the
Steam and Wash Temp buttons, and another model is the Pre-Soak and Bottle Jets buttons.
The Control Lock light will turn on to indicate the control is locked.
To UNLOCK the dishwasher control, depending on the model, press and hold the 1 or 2
buttons indicated on the controls for 3 seconds. The Control Lock light will turn off to indicate the
control is unlocked.
Loading section.
one time and close door to begin countdown. The
8 49-4000042
Getting Started
Start Dishwasher
6
Start Press the Start button and close the door within 4 seconds to start the cycle or begin the Delay
Hours countdown. The wash cycle will begin shortly after closing the door. The display will turn
off if the door remains open for two minutes. To activate the display, close and open the door or
press any button.
Interrupt or
Pause
Cancel To cancel a wash cycle, press and hold the Start button for 3 seconds and close door.
Cycle Indicator Lights and Sounds
7
Sanitized
or Cycle
Sanitized
Clean
or Cycle
Complete
Low Rinse
Aid
(on some
models)
Cycle
Status
(on some
models)
Sounds The dishwasher will emit a sound to indicate cycle completion, button presses, and door ajar. To
Sabbath/
Door
Wake Up
Mode
(on some
models)
To interrupt or pause a dish cycle, slowly open the door. Opening the door will cause the wash
cycle to pause. The dishwasher will beep every minute to remind you to close the door. To restart
or resume the cycle, press Start, and close the door within 4 seconds.
The dishwasher will drain, emit a beep sound, and the wash cycle light will turn OFF.
Displayed at end of the cycle when Wash Temp Sani or Sanitize Temp has been selected and
dishwasher has met requirements for sanitization. See Wash Temp Sani or Sanitize Temp, for
complete description. Closing door or pressing any button will turn off light.
Displayed when a wash cycle is complete. The light stays ON as a reminder that the dishes are
clean. The light will turn off when the door is opened.
Displayed when rinse agent is low or empty. See Use a Rinse Agent section. To turn indicator
off, press the Pre-Soak or Steam button 7 times within 5 seconds. Repeat this process to turn
the Low Rinse Aid indicator back on.
The indicator light on the door front will change color to indicate the wash status. During the
wash cycle, the indicator light will be amber. When the wash cycle is complete, the light will
change to green.
mute all sounds, press the Heated Dry or Power Dry button 7 times within 5 seconds. Repeat
this process to turn sounds back on.
To turn this option ON/OFF, press and hold the Start and Wash Temp buttons for 5 seconds,
close the door and wait 3 minutes for the dishwasher to go into sleep mode. In the OFF mode,
the control display, control sounds, and interior lights (on some models) will not respond to the
door opening/closing. This mode can be used when observing certain religious holidays such as
the Sabbath. To activate the control and interior lights
(on some models), press any button.
USING THE DISHWASHER
49-4000042 9
Dispensers
Check the Water Temperature
The entering water should be at least 120°F (49°C) and
not more than 150°F (66°C) for effective cleaning and to
prevent dish damage. Check the water temperature with a
candy or meat thermometer.
Use a Rinse Agent
Rinse agents, such as Finish® Jet-Dry®Rinse Aid are designed for great drying action and to protect against spots
and film build-up on your dishes, glasses, flatware, cookware, and plastic.
Filling the Rinse Agent Dispenser
The rinse agent dispenser holds 3.5 oz. (104 ml) of rinse agent. Under normal conditions, this will last approximately
one month.
Make sure the dishwasher door is fully open.
1
Open the rinse agent dispenser door.
2
USING THE DISHWASHER
Slowly add rinse agent until the cup is full. You may need to pause several times to
3
allow rinse aid to settle. NOTE: Indicator window does not light up.
Clean up any spilled rinse agent with a damp cloth to prevent foam from forming
4
inside the dishwasher.
Turn on the hot water faucet nearest the dishwasher,
place the thermometer in a glass and let the water run
continuously into the glass until the temperature stops
rising.
Indicator
window
Close the rinse agent dispenser door.
5
Rinse Aid Setting
The amount of rinse agent released into the final wash can be adjusted. If water drops or
hard water spots remain on dishes after the dry cycle, increase the setting.
To adjust the setting
Open the Rinse Agent dispenser door;
then turn the adjuster clockwise to
increase the amount of rinse agent,
counterclockwise to reduce the amount
of rinse agent.
Clockwise to reduce
water drops and
hard water spots
Counterclockwise
to reduce foaming
Rinse
agent
adjuster
10 49-4000042
Dispensers
USING THE DISHWASHER
Detergent Dispenser
The detergent dispenser is located in the center of
the dishwasher door. It has two compartments. The
main wash compartment is found inside the detergent
dispenser. To open, press the button on the side of the
dispenser. The pre-wash compartment is on the lid of
the detergent dispenser. Use the pre-wash compartment
only when your water is extremely hard or when you
have a heavy soiled load. The pre-wash compartment is
not used when tablet or packet detergents are used.
NOTE: Do not load large items in the lower rack where
they may block the wash jets from rinsing out the
detergent dispenser.
Detergent
Dispenser
You may use tablet, packet, powder, liquid or gel automatic
dishwasher detergent. Make sure you use only detergents
specifically labeled for use in automatic dishwashers. Never
use liquid hand dish detergent in an automatic dishwasher.
Sudsing and poor wash performance will result with the use
of improper detergents.
Detergents should be stored in a dry location and in their
original container to prevent loss of effectiveness. Place
detergent in the cup just prior to starting the dishwasher
and then close the cover. The cover will open during the
wash cycle.
Main
Wash
Pre-Wash
Push/Slide
to Close
Use the table as a starting point and then adjust the
amount of detergent you use. Use just enough to get
good wash performance. Using just the right amount of
detergent will provide great wash performance without
wasting detergent or etching glassware.
Number of
Grains/Gal.
Less than 4 Fill cup to 1/3 full
4 to 8 Fill cup to 2/3 full
8 to 12 Fill cup completely full
Greater than 12
Using too much detergent with very soft and/or very
hot water may cause a condition called etching on your
glassware. Etching is a permanent cloudiness in your
glassware. This condition is irreversible. However, using
too little detergent will cause poor wash performance.
DO NOT USE HAND DISH DETERGENT
Detergent Cup(s) to Fill
Fill both main wash cup and pre
wash cup
Rinse Agent
Filling the Detergent Dispenser
Café recommends using detergent in tablet or packet
form. Independent testing has shown this form of
detergent is very effective in the dishwasher. Finish
Quantum®Powerball® is an example of this type of
detergent. Simply put a tablet or packet into the main
wash compartment and close the detergent cup cover.
Please notice that the tablet or packet must be placed in
the main wash compartment of the detergent cup. If the
tablet or packet is placed in the prewash compartment or
tossed in the bottom of the dishwasher, the detergent will
be flushed down the drain in a very short period of time
and will thus be wasted. Wash performance will be very
poor as a result.
If you choose to use detergent in powder, liquid or gel
form, the amount of detergent you use will be determined
by the hardness of your water, the temperature of your
water, and the food soil load inside the dishwasher.
Contact your water company to get information about
the hardness of the water in your area. Water hardness
is measured in grains per gallon. Use this information
and the table above to determine the amount of detergent
to use. You may purchase a hard water test strip from
Café. Visit cafeappliances.com/parts for WD01X10295.
In Canada, visit cafeappliances.ca/parts.
®
NOTE: Using a detergent that is not specifically designed
for dishwashers will cause the dishwasher to fill with suds.
During operation, these suds will spill out of the dishwasher
vents, covering the kitchen floor and making the floor wet.
Because so many detergent containers look alike,
store the dishwasher detergent in a separate space
from all other cleaners. Show anyone who may use the
dishwasher the correct detergent and where it is stored.
While there will be no lasting damage to the dishwasher,
your dishes will not get clean using a dishwashing
detergent that is not formulated for automatic dishwashers.
49-4000042 11
Appliance Communication
WiFi Connect
Your dishwasher is Café WiFi Connect capable. A WiFi
communciation card is built into the product allowing
it to communicate with your smartphone for remote
monitoring, control and notifications.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and
USING THE DISHWASHER
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Please visit cafeappliances.com/connect to connect
your appliance, learn more about connected appliance
features and learn what connected appliance app’s will
work with your smartphone.
In Canada, visit cafeappliances.ca/connect.
• Consult the dealer or an experienced radio/television technician for help.
Labelling: Changes or modifications to this unit not expressly approved by the manufacturer could void the user’s
authority to operate the equipment.
12 49-4000042
Loading
For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware
baskets may vary from your model.
Upper Rack
The upper rack is primarily for glasses, cups, and
saucers. For best wash performance, tilt cup and glass
openings toward the center of the rack. Other items such
as pots, pans, and plates may be placed in the upper
rack. This is also a secure place for dishwasher-safe
plastic items. The upper rack can be used for odd sized
utensils. Sauce pans, mixing bowls, and other similarly
shaped items should be placed face down for best wash
performance. Ensure small plastic items are secure so
that they cannot fall on the heater at the bottom of the
dishwasher, potentially damaging the item. Some models
are equipped with a hidden heater, so dishwasher safe
plastic items can be placed in the lower rack.
IMPORTANT: Ensure items in the upper rack do not
interfere with the 3rd Rack (on some models) when
loading and unloading.
IMPORTANT: Ensure that items do not protrude through
the bottom of the rack or silverware basket where they
will block the rotation of the middle spray arm. This
could result in noise during operation and/or poor wash
performance.
USING THE DISHWASHER
The Bottle Jets system (on some models) is the ideal
location to position baby bottles, tall sports bottles, or
other tall items with narrow openings. The Bottle Jets
clips hold bottles with small openings in place so water
jets are directed inside the bottles to clean hard to reach
areas. Clips can be installed or removed by simply
slipping the clip opening over the top of the nozzle.
Clip
Nozzle
Bottle Jets
Sports bottle held in place
over a Bottle Jets clip
Baby bottle held in place
under a Bottle Jets clip
49-4000042 13
Loading
CAUTION
A loaded upper rack may be
heavier than anticipated. To prevent
minor injury or damage to the contents, do not raise
or lower the upper rack after the rack is loaded.
The upper rack allows 2” of adjustment up or down to
accommodate large items. The upper rack may be lowered
by pushing the long flaps on each side of the rack. This will
allow you to lower the rack (see fig. Upper Rack). To raise
the rack, lift up on the rack until the rack locks in place.
To add flexibility in loading, the stem safe shelf (on some
models) may be placed in the up or down position or
unfolded and placed in the lower unfolded position.
The shelf may also be used to secure stemware such as
wine glasses. Because these stemware items come in
various sizes, slowly push the rack in to ensure the items
USING THE DISHWASHER
do not bump into the edges of the dishwasher, which
may cause damage to the items.
The fold down tines (on some models) provide flexibility
for extra-large and hard-to-fit items. The tine rows can be
adjusted to a vertical or lay-down position.
Place the
slots in the
utility shelf
clips over
the vertical
rack wires
and
push
down to attach
utility shelf
onto
second
wire of rack
Push
Upper Rack
For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware
baskets may vary from your model.
8 Place Settings - Upper Rack
Models - CDT706 & CDT866
Model - CDT836
14 49-4000042
Loading
USING THE DISHWASHER
10 Place Settings - Upper Rack
Model - CDT706
Model - CDT836
12 Place Settings - Upper Rack
Models - CDT706 & CDT866
Model - CDT836
Model - CDT866
49-4000042 15
Loading
For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware baskets
may vary from your model.
Lower Rack
The lower rack is best used for plates, saucers and
cookware items. Large items, such as broiler pans and
baking racks should be placed along the sides of the rack.
If necessary, oversized glasses and mugs can be placed in
the lower rack to maximize loading flexibility. Plates, saucers
and similar items should be placed between the tines in the
direction that allows the item to remain secure in the rack.
NOTE: Do not load large items in the lower rack where they may
block the wash jets from rinsing out the detergent dispenser.
The lower rack fold down tines (on some models) can
be adjusted
to different
upright
USING THE DISHWASHER
angles or
placed flat
to provide
flexibility for
hard-to-fit or
extra-large
items.
The reversible tine blocks (on some models) are designed
to allow greater flexibility in loading dishes. The direction
of the tine blocks can be changed to match your preferred
loading direction as shown in Figure A or Figure B:
3 Angled
Positions
Available
or Folded
Down
WARNING
the dishwasher. Keep out of reach of children.
To change the direction of the fold down tines, lower
the tines, then pull away from the bar clips that secure
the tines to the rack and remove. Reverse the direction
of the tines, orienting the handle on the opposite side of
the rack. Reattach the tines to the bar clips by pushing
the tines back until they click in place. The indexer will
also need to be switched to the opposite side of the
dishwasher. To remove the indexer, simply slide it the
in the direction labeled “unlock.” Then, align the indexer
with the rack on the other side and slide in the direction
that says “lock” in order to reattach the indexer to the
rack.
IMPORTANT:
protrude through the bottom of the rack or the silverware
basket where they will block the rotation of the lower
spray arm. Also, ensure that large plates, pots, or tall
items don’t hit the mid spray arm. This could result in
noise during operation and/or poor wash performance.
The clips can be a choke hazard
for small children if removed from
It is important to ensure that items do not
Bar Clip
Figure A Figure B
To adjust the tine block direction, remove the clips
securing the tine blocks to the racks by pulling up on the
tab, then gently flex the retaining wire from the center to
unseat the tine block from the lower rack. The tine block
may be turned in the opposite direction to reverse loading
direction. Secure the tine block to the rack using the same
process and be sure to snap the clips back in place.
Clip
Indexer
To lock, slide right.
To unlock, slide left.
16 49-4000042
Loading
8 Place Settings - Lower Rack
Models - CDT706 & CDT866
10 Place Settings - Lower Rack
Model - CDT706
Model - CDT836
USING THE DISHWASHER
Model - CDT836
Model - CDT866
12 Place Settings - Lower Rack
Models - CDT706 & CDT866
49-4000042 17
Model - CDT836
Loading
For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware
baskets may vary from your model.
3rd Rack (on some models)
The 3rd rack is the recommended location for silverware
and large utensils
CAUTION
utensil tray. The tray may contain sharp or heavy
items. If items are dropped from the tray or the tray
is dropped, injury could occur.
Take care when loading, unloading,
or transporting the silverware or
IMPORTANT NOTES:
Do not allow cutlery of different materials to touch each
Ŷ
other in the 3rd rack. Doing so may cause discoloration
of the cutlery.
Ŷ The tray is only meant to be used with a Café 3rd rack
dishwasher to hold silverware, cooking utensils,
and other small items. Using the tray for any other
purpose could result in damage to the tray or damage
to anything interacting with the tray.
Ŷ Ensure that the 3rd rack is fully closed before shutting
the dishwasher door. Shutting the door with the
rack partially extended could cause damage to the
dishwasher.
8 Place Settings
10 Place Settings 12 Place Settings
USING THE DISHWASHER
The 3rd rack is also removable to allow extra large items to be placed in the upper rack:
To remove the 3rd rack:
With the rack fully extended, lift the front of the rack so that
1
the rack roller wheels clear the retaining hook
Continue to pull the rack until the remaining rack roller
2
wheels clear the retaining hook.
Replace the rack by aligning the rack roller wheels on the
3
retaining hook and rack rails – Ensure all roller wheels are
located on top of the rack rails
.
.
18 49-4000042
Loading
Silverware/flatware is loaded using the silverware basket lids. This ensures great wash performance of the
silverware. Loading in this manner prevents nesting and makes sure all items are washed uniformly.
Silverware Basket
Place flatware in the removable silverware baskets.
Sharp objects, such as forks and knives, may be placed
with the handles facing up, in order to protect your hands.
For the best wash performance, place other items such
as spoons with the handles facing down. Avoid allowing
items to nest together, which may keep them from being
properly washed. When loading, distribute items evenly in
the basket.
The silverware baskets may also be used for small items,
such as measuring spoons, baby bottle nipples, plastic
lids, or corn cob holders. The silverware basket covers
can be closed to contain small items.
IMPORTANT: Do not load large or
tall utensils where they may block the
detergent dispenser, mid spray arm, or
become trapped between the door and
the gasket when the door is closed.
Deep Clean Silverware Jets
(on some models)
Deep Clean Silverware Jets target
stubborn, stuck-on food and help separate
nested spoons and forks to keep your
silverware spotless no matter how you
load the silverware. For optimal silverware
cleaning, the use of silverware basket lids
is always recommended. For models with
the third rack, the Deep Clean Silverware
Jets can also be used to clean mixing
bowls and other cookware.
Do not remove Deep Clean Silverware Jet
spray assembly from the dishwasher rack.
Silverware
basket lids
Ensure tabs on
back of silverware
basket are hooked
on top wire of lower
rack
Deep Clean
Silverware Jets
USING THE DISHWASHER
Silverware Basket - 8 Place Settings
Models - CDT706 & CDT836
Silverware Basket
Model - CDT866
NOTE: Refer to the 3rd Rack in this
Loading The Dishwasher section.
49-4000042 19
- 8 Place Settings
Silverware Basket - 10 Place Settings
Models - CDT706 & CDT836
Silverware Basket
Model - CDT866
NOTE: Refer to the 3rd Rack in this
Loading The Dishwasher section.
- 10 Place Settings
Silverware Basket - 12 Place Settings
Models - CDT706 & CDT836
Silverware Basket - 12 Place Settings
Model - CDT866
Care and Cleaning
Control Panel
To clean the control panel, use a lightly dampened cloth.
Then dry thoroughly.
Exterior Door Panel
Before cleaning the front panel, make sure you know what
type of panel you have. Refer to the last two letters of
your model number. You can locate your model number
on the left-hand tub wall just inside the door. If your model
number ends with D1 or W2 then you have a painted door
panel. If your model number ends with S1, then you have
a stainless steel door panel.
Follow the instructions below for cleaning the door panel for
your specific model.
Painted Door Panel (model numbers ending in D1–Matte
Black or W2–Matte White)
USING THE DISHWASHER
Use a clean, soft, lightly dampened cloth, then dry
thoroughly.
Stainless Steel Door Panel (model numbers ending in S1)
For cleaning rust and tarnish, cleaners with oxalic acid
such as Bar Keepers Friend Soft Cleanser™ will remove
rust, tarnish and small blemishes. Use only a liquid cleanser
free of grit and rub in the direction of the brush lines with a
damp soft sponge. Do not use appliance wax or polish on
the stainless steel.
For other blemishes and marks, use Stainless Steel
Magic or a similar product using a clean soft cloth.
Do not use appliance wax, polish, bleach or products
containing chlorine on stainless steel. You can order
Stainless Steel Magic WX10X29 through Café by
visiting cafeappliances.com/parts. In Canada, visit
cafeappliances.ca/parts.
Dishwasher Interior
To clean and de-odorize your dishwasher, use citric acid
or Finish® Dishwasher Cleaner, a detergent additive.
Finish® Dishwasher Cleaner will break up mineral
deposits, and remove hard water film and stains. You
can order citric acid Café kit WD35X151 through Café
Parts by visiting cafeappliances.com/parts. In Canada,
visit cafeappliances.ca/parts. You can purchase Finish
Dishwasher Cleaner at your local grocery store.
®
Stainless Steel Inner Door and Tub
The stainless steel used to make the dishwasher tub and
inner door provides the highest reliability available in a
Café dishwasher.
If the dishwasher tub or inner door should be scratched
or dented during normal use, they will not rust or corrode.
These surface blemishes will not affect their function or
durability.
20 49-4000042
Care and Cleaning
Filters
Inspect and clean the filters periodically. This should be done every other month or more depending on usage. If
there is a decrease in wash performance or dishes feel gritty, this is also an indication the filters need to be cleaned.
USING THE DISHWASHER
WARNING
removed from the dishwasher. Keep out of reach
of children.
The retaining posts can be a
choke hazard for small children if
Ultra-Fine Filter
To clean the Ultra-Fine Filter, remove the bottom rack.
Twist the Ultra-Fine Filter counterclockwise and lift to
remove. Rinse filter with warm soapy water and use
a sponge to carefully remove any stubborn particles.
Scrubbing with scouring pads or brushes can damage
the filter. Once cleaned, replace the Ultra-Fine Filter, and
twist it clockwise to lock in place.
Fine Filter
To clean the Fine Filter (mesh plate), remove the bottom
rack. Remove the Ultra-Fine Filter.
Twist each of the two retaining posts located toward the
back bottom of the tub counterclockwise, and remove the
Fine Filter. Rinse filter with warm soapy water. Scouring
pads or brushes can scratch the filter surface but a soft
brush or sponge may be needed to remove stubborn
soils or calcium deposits caused by hard water. Once
cleaned, replace the Fine Filter and the Ultra-Fine Filter.
Twist the two retaining posts clockwise to lock in place.
Retaining
Posts
Spray
Arm
Protect Against Freezing
If your dishwasher is left in an unheated place during the
winter, ask a service technician to:
Turn off electrical power to the dishwasher. Remove
1
fuses or trip circuit breaker.
Turn off the water supply and disconnect the water inlet
2
line from the water valve.
Does Your Dishwasher Have an Air Gap?
An air gap protects your dishwasher
against water backing up into it if a drain
clogs. The air gap is not a part of the
dishwasher. It is not covered by your
warranty. Not all plumbing codes require
air gaps, so you may not have one.
Air gap
Check the air gap any
time your dishwasher
isn’t draining well.
Fine
Filter
Drain water from the water inlet line and water valve.
3
(Use a pan to catch the water.)
Reconnect the water inlet line to the water valve.
4
The air gap is easy to clean.
Turn off the dishwasher and lift off the air gap cover.
1
Remove the plastic cap under the cover and clean with a
2
toothpick.
Replace the cap and cover when the air gap is clean.
3
Ultra-Fine
Filter
49-4000042 21
Troubleshooting Tips... Before you schedule service
Problem Possible Cause What To Do
Start status indicator
light flashing
Dishwasher BEEPS
once every minute
Display shows
“LEAK DETECTED”
Beeping at the end
of the cycle (on
some models)
Dishes and flatware
TROUBLESHOOTING TIPS
not clean
Spots and filming
on glasses and
flatware
Cloudiness on
glassware
The door was opened or the
cycle was interrupted.
This is a reminder that your
dishwasher door has been left
open during operation. It will
continue beeping until you
press Start and close the door.
Possible leak is detected Some models are equipped with leak detection and the
This is normal. Dishwasher
will beep twice at the end of
the cycle.
Ultra-Fine Filter or Fine
Filter is clogged
Low inlet water temperature Make sure inlet water temperature is correct (see the
Water pressure is
temporarily low
Air gap or disposer clogged Clean the air gap or flush the disposer.
High drain loop or air gap
not installed
Improper rack loading Make sure large dishware does not block the detergent
Poor performing detergent Use a highly rated detergent such as Finish
Extremely hard water Use rinse agents such as
Low inlet water temperature Make sure water temperature is at least 120°F (49°C).
Overloading or improper
loading of the dishwasher
Old or damp powder
detergent
Rinse agent dispenser empty
Too little or low performing
detergent
Combination of soft water
and too much detergent
Low performing phosphatefree detergent
Water temperature entering
the dishwasher exceeds
150°F (66°C)
Press the Start button once and close the door within 4
seconds to start the dishwasher. Press the Start button a
second time when the dishwasher is running only if you
wish to cancel the cycle.
Press Start and close the door.
cycle will be cancelled if a leak is detected. The display
will show “LEAK DETECTED”. Contact Café for service.
To turn off the double beep indicator (or re-activate it if it
was previously turned off), press the Heated Dry button 5
times within 3 seconds. A triple beep will sound to indicate
the end-of-cycle beep option has been turned on or off.
See the Care and Cleaning section.
USING THE DISHWASHER section). Turn on the hot
water faucet nearest the dishwasher, let run until the water
temperature stops rising. Then start the dishwasher and
turn off the faucet. This ensures the entering water is hot.
Select Wash Temp Boost or Boost Temp if available.
Turn on a faucet. Is water coming out more slowly than usual?
If so, wait until pressure is normal before using your dishwasher.
Normal water pressure to the dishwasher should be 20-120 psi.
Refer to the Installation Instructions for proper drain line
installation.
dispenser or the wash arms. See the Loading section.
Automatic Dishwashing Detergent.
Finish® Jet-Dry®Rinse Aid to
prevent spots and prevent new film build-up.
If water is extremely hard, a softener may be required.
Load dishwasher as shown in the Loading section.
Make sure detergent is fresh.
detergent such as Finish
Dishwashing Detergent
Refill with rinse agent such as Finish® Jet-Dry®Rinse Aid.
Make sure you use the proper amount of highly rated
detergent.
This is called etching and is permanent. To prevent this
from happening, use less detergent if you have soft water.
Wash glassware in the shortest cycle that will get it clean.
See A white film on glassware, dishware and the
interior in this TROUBLESHOOTING section.
This could be etching. Lower the water heater
temperature.
Use a highly rated
®
Quantum® Automatic
.
®
Quantum
®
22 49-4000042
Troubleshooting Tips... Before you schedule service
Problem Possible Cause What To Do
Suds in the tub Wrong detergent Use only automatic dishwasher detergents to avoid sudsing.
Finish® Quantum® Automatic Dishwashing Detergent
has been approved for use in all Café dishwashers.
To remove suds from the tub, open the dishwasher and
let suds dissipate. Open the door, press and hold Start
for 3 seconds, and close the door.
Rinse agent was spilled Always wipe up rinse agent spills immediately.
Detergent left in
dispenser cups
Black or gray marks
on dishes
Dishes don’t dry Low inlet water temperature Make sure inlet water temperature is at least 120°F.
Control panel
responded to inputs
but dishwasher
never filled with
water
Stained tub interior White film on inside
Dishwasher won’t
run
Dishes or utensils are
blocking the detergent cup
Aluminum utensils have
rubbed against dishes
Rinse agent dispenser is
empty
Additional drying time is
needed
Door may not be completely
closed
Water valve may be turned
off
Flood float may be stuck Remove Ultra-Fine filter and lightly tap the piece under the
surface— hard water
minerals
Fuse is blown or circuit
breaker is tripped
Power is turned off In some installations, the power to the dishwasher is
Control panel is locked Unlock control panel. See the Getting started section.
Possible leak is detected Some models are equipped with leak detection and the
Proper Start sequence was
not followed
Reposition the dishes, so the water from the lower spray
arm can flush the detergent cup. See the Loading section.
Reposition the tall utensils or heavy silverware that may
be keeping the dispenser cup door from opening. See
the Loading section.
Don’t place large bowls or pots directly under the
detergent dispenser.
Remove marks with a mild, abrasive cleaner.
Select Heated Dry.
Use Wash Temp Boost or Boost Temp option.
Select a higher cycle, such as Wash Temp Sani,
Sanitize Temp or Heavy.
Check the rinse agent dispenser and fill as required.
Leave door closed after the Clean light appears to allow
the fan to run an additional 90 minutes.
Note: If you open the door, this fan extension will be cancelled.
Make sure the door is firmly closed.
Make sure water valve (usually located under the sink) is
turned on.
ultra fine filter that looks like a salt shaker. Replace the filter.
Café recommends Finish
prevent hard water mineral deposits from forming.
Run dishwasher with citric acid to remove mineral deposits.
Citric acid (WD35X151) can be ordered through Café Parts.
See back cover for ordering information. Alternatively,
purchase
directions on the label.
Replace fuse or reset circuit breaker. Remove any other
appliances from the circuit.
provided through a wall switch, often located next to the
disposer switch. Make sure it is on.
cycle will be cancelled if a leak is detected. The display
will show “LEAK DETECTED”. Contact Café for service.
See the Using the dishwasher
Finish
®
Dishwasher Cleaner and follow the
®
Jet-Dry®Rinse Aid to help
section.
TROUBLESHOOTING TIPS
49-4000042 23
Troubleshooting Tips... Before you schedule service
Problem Possible Cause What To Do
Control panel lights
go off when you’re
setting controls
Water standing in
the bottom of the
tub
Water won’t pump
out of the tub
Steam This is normal Warm, moist air comes through the vent during drying and
Sanitized or Cycle
Sanitized light does
not illuminate at the
TROUBLESHOOTING TIPS
end of the cycle
Noise Normal operating sounds:
A white film on
glassware, dishware
and the interior
24 49-4000042
Time too long between
touching of selected
buttons
Air gap is clogged Clean the air gap. See the Care and Cleaning section.
High drain loop or air gap
not installed
Drain is clogged If you have an air gap, clean it. See the Care and
The door was opened and
the cycle was interrupted
during final rinse
The incoming water
temperature was too low
Beeping at the end of the
cycle (on some models)
Detergent cup opening
Water entering dishwasher
Motor stops and starts at
various times during cycle
Spray arms start and stop
at various times
Drain pump sounds during
pump out
Drain pump starts and
stops several times during
each drain
Rattling dishes when the
spray arm rotates
Rattling silverware against
door during wash
This problem is likely
caused by a low quality
phosphate-free dishwasher
detergent
Each button must be touched within 30 seconds of the
others. To relight, touch any button again or open the
door and unlock (top control).
Refer to the Installation Instructions for proper drain line
installation.
Cleaning section.
If the dishwasher drains into a disposer, run disposer clear.
Check to see if your kitchen sink is draining well. If not,
you may need a plumber.
when water is being pumped out. This is necessary for drying.
Do not interrupt the cycle by opening the door during the
wash cycle.
Raise the water heater temperature to between 120°F
and 150°F.
These are all normal. No action is required.
Make sure dishes are properly loaded. See the Loading
section.
Tall utensils may be placed in the upper rack to avoid
bumping against inner door during wash cycle.
To remove the white film, run your dishes through a
dishwasher cycle with citric acid. Use a WD35X151
citric acid kit found online. Otherwise, use Finish
Dishwasher Cleaner found at your local grocery store.
Pour the citric acid in the detergent cup and close the
cover. Place the filmed but otherwise clean glassware and
dishware in the dishwasher. Leave silverware and other
metal items out of the dishwasher. Turn the dishwasher on
and let it run through a complete cycle without detergent.
The glassware, dishware, and dishwasher should come out
film free. Alternatively, a vinegar rinse may be used. Pour 1
cup of vinegar into dishwasher just after the detergent cup
opens and let the dishwasher complete its cycle.
This may be repeated several times a year as needed.
The use of a rinse agent such as
Rinse Aid may help minimize a repeat build up of film.
Also, the use of a highly rated detergent such as Finish
Quantum® Automatic Dishwashing Detergent will help
prevent film build-up.
Finish
®
Jet-Dry
®
®
®
Café Dishwasher Limited Warranty
cafeappliances.com (United States) | cafeappliances.ca (Canada)
All warranty service is provided by our Factory Service Centers, or an authorized service technician. To schedule service
online, visit us at cafeappliances.com/service. In Canada, visit: cafeappliances.ca/service. Please have your serial
number and your model number available when scheduling service.
Servicing your appliance may require the use of the onboard data port for diagnostics. This gives a Café factory service
technician the ability to quickly diagnose any issues with your appliance and helps Café improve its products by providing
Café with information on your appliance. If you do not want your appliance data to be sent to Café, please advise your
technician not to submit the data to Café at the time of service.
For the period of: We will replace:
One year
From the date of the
original purchase
What is not covered:
Ŷ
Service trips to your home to teach you how to use
the product.
Ŷ
Improper installation, delivery or maintenance.
Ŷ
Failure of the product if it is abused, misused, or used for
other than the intended purpose or used commercially.
Ŷ
Replacement of house fuses or resetting of circuit
breakers.
Ŷ
Product not accessible to provide required service.
Any part of the dishwasher which fails due to a defect in materials or workmanship.
During this limited one-year warranty, we will also provide, free of charge, all labor
and related service to replace the defective part.
Ŷ
Damage to the product caused by accident, fire,
floods or acts of God.
Ŷ
Incidental or consequential damage caused by
possible defects with this appliance.
Ŷ
Cleaning or servicing of the air gap device in the drain
line.
Ŷ
Damage caused after delivery including damage from
items dropped on the door.
LIMITED WARRANTY
Staple your receipt here. Proof of the original purchase
date is needed to obtain service under the warranty.
EXCLUSION OF IMPLIED WARRANTIES
Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any implied warranties,
including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or the
shortest period allowed by law.
In the United States:
This limited warranty is extended to the original purchaser and any succeeding owner for products purchased for home use
within the USA. If the product is located in an area where service by a Café Authorized Servicer is not available, you may
be responsible for a trip charge or you may be required to bring the product to an Authorized Café Service location for
service. In Alaska, the limited warranty excludes the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty
gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your
legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor: GE Appliances, a Haier Company
Louisville, KY 40225
In Canada:
This limited warranty is extended to the original purchaser and any succeeding owner for products purchased in Canada
for home use within Canada. If the product is located in an area where service by a Café Authorized Servicer is not
available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized Café
Service location.
Some provinces do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty
gives you specific legal rights, and you may also have other rights which vary from province to province. To know what
your legal rights are, consult your local or provincial consumer affairs office.
Warrantor: MC Commercial Inc., Burlington, ON, L7R 5B6
Extended Warranties: Purchase a Café extended warranty and learn about special discounts that are available while
your warranty is still in effect. You can purchase it online anytime at
In the US, visit: cafeappliances.com/extended-warranty. | In Canada, visit: cafeappliances.ca/extended-warranty.
Café Service will still be there after your warranty expires.
49-4000042 25
Consumer Support
Café Website
Have a question or need assistance with your appliance? Try the Café website 24 hours a day, any day of the year!
You can also shop for more great Café products and take advantage of all our on-line support services designed for
your convenience. In the US: cafeappliances.com. In Canada: cafeappliances.ca.
Register Your Appliance
Register your new appliance on-line at your convenience! Timely product registration will allow for enhanced
communication and prompt service under the terms of your warranty, should the need arise. You may also mail in
the pre-printed registration card included in the packing material. In the US: cafeappliances.com/register.
In Canada: cafeappliances.ca/registration.
Schedule Service
Expert Café repair service is only one step away from your door. Get on-line and schedule your service at your
CONSUMER SUPPORT
convenience any day of the year. In the US: cafeappliances.com/service. In Canada: cafeappliances.ca/service.
Extended Warranties
Purchase a Café extended warranty and learn about special discounts that are available while your warranty is still in
effect. You can purchase it on-line anytime. Café Service will still be there after your warranty expires.
In the US: cafeappliances.com/extended-warranty. In Canada: cafeappliances.ca/extended-warranty.
Remote Connectivity
For assistance with wireless network connectivity, visit our website at cafeappliances.com/connect.
In Canada: cafeappliances.ca/connect.
Parts and Accessories
Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes
(VISA, MasterCard and Discover cards are accepted). Order on-line today 24 hours every day.
In the US: cafeappliances.com/parts. In Canada: cafeappliances.ca/parts.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing
generally should be referred to qualified service personnel. Caution must be exercised, since improper
servicing may cause unsafe operation.
Contact Us
If you are not satisfied with the service you receive from Café, contact us on our website with all the details including
your phone number, or write to:
In the US: General Manager, Customer Relations, Café | Appliance Park | Louisville, KY 40225
cafeappliances.com/contact.
In Canada: Director, Consumer Relations, Mabe Canada Inc. | Suite 310, 1 Factory Lane | Moncton, N.B. E1C 9M3
cafeappliances.ca/contact.
26 49-4000042
Loading...