Cafe CDD220P4WW2 Installation Instructions

TM

Installation Instructions Dishwasher Drawer

If you have questions, visit our website at: cafeappliances.com

BEFORE YOU BEGIN - Read these instructions completely and carefully.

WARNING

Ŷ

To reduce the risk of electric shock, fire, or injury to persons, the installer must

ensure that the dishwasher is completely enclosed at the time of installation.

Ŷ

FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker before

beginning installation. Do not use an extension cord or adapter plug with this
appliance.

Ŷ

The improper connection of the equipment grounding conductor can result in a

risk of electric shock. Check with a qualified electrician or service representative
if you are in doubt that the appliance is properly grounded.

Ŷ

If house wiring is not 2-wire with ground, a ground must be provided by the installer.

When house wiring is aluminum, be sure to use UL-Listed anti-oxidant
compound and aluminum-to-copper connectors.

Ŷ

To reduce the risk of electric shock, fire, or injury to persons, the installer should

check to ensure that wires
to the dishwasher through a strain relief, and
the time of install

Ŷ

For models equipped with power cord: Do not modify the plug provided

with the appliance; if it will not fit the outlet, have a proper outlet installed by a
qualified technician.

are contained inside of the terminal block cover.

are not pinched or damaged, the house wiring is attached

all electrical connections made at

FOR YOUR SAFETY

Read and observe all WARNINGS and CAUTIONS shown throughout these
instructions.

IMPORTANT – Observe all governing codes and ordinances.

ŶNote to Installer – Be sure to leave these instructions for the consumer’s and

local inspector’s use.

ŶNote to Consumer – Keep these instructions with your Owner’s Manual for

future reference.

ŶSkill Level – Installation of this dishwasher requires basic mechanical, electrical

and plumbing skills. Proper installation is the responsibility of the installer.

Product failure due to improper installation is not covered under the GE
Appliances Warranty. See Warranty information.

ŶCompletion Time – 1 to 3 Hours. New installations require more time than

replacement installations.

IMPORTANT – The dishwasher MUST be installed to allow for future removal from
the enclosure if service is required.

Care should be exercised when the appliance is installed or removed, to reduce the
likelihood of damage to the power supply cord.

If you received a damaged dishwasher, you should immediately contact your dealer
or builder.

Your dishwasher is a water heating appliance.

CAUTION

While performing installations described in this booklet, gloves, safety glasses
or goggles should be worn.

READ CAREFULLY

KEEP THESE INSTRUCTIONS

Precauciones en Español

ANTES DE COMENZAR - Lea estas instrucciones en su totalidad y atentamente.

ADVERTENCIA

Ŷ

Para reducir el riesgo de descarga eléctrica, incendio o lesiones a personas, el

instalador debe asegurarse de que el lavaplatos esté completamente cerrado en el
momento de la instalación.

Ŷ

PARA SEGURIDAD PERSONAL: Quite el fusible o abra el interruptor de

circuitos antes de comenzar la instalación. No utilice un cable de extensión o un
enchufe adaptador con este artefacto.

Ŷ

La conexión inadecuada del conductor de conexión a tierra del equipamiento

puede provocar un riesgo de descarga eléctrica. Consulte a un electricista

FDOL¿FDGRRUHSUHVHQWDQWHGHVHUYLFLRWpFQLFRVLWLHQHGXGDVVREUHODFRUUHFWD

conexión a tierra del aparato.

Ŷ

Si el cableado doméstico no cuenta con un cable de 2 hilos con conexión a
tierra, un instalador debe realizar una conexión a tierra. Cuando el cableado
doméstico es de aluminio, asegúrese de usar un compuesto antioxidante y

conectores de aluminio a cobre aprobados por UL.

Ŷ

Para reducir el riesgo de descarga eléctrica, incendio o
el instalador deberá realizar un
pellizcados
de empalmes a través de un amortiguador
eléctricas

dentro de la tapa de la caja de empalmes.

ni dañados, que el cableado del hogar esté conectado a la ficha de la caja

realizadas en el momento de la instalación (tuercas para

control para asegurar que los cables no estén

de refuerzo, y que todas las conexiones

lesiones a personas,

cables) estén

PARA SU SEGURIDAD

Lea y cumpla con todas las ADVERTENCIAS y PRECAUCIONES que figuran
en estas instrucciones.

IMPORTANTE – Cumpla con todos los códigos y ordenanzas gubernamentales.

ŶNota para el Instalador – Asegúrese de entregar estas instrucciones al consumidor

y al inspector local.

ŶNota para el Consumidor – Guarde estas instrucciones con su Manual del

Propietario para referencia futura.

Ŷ Nivel de habilidad – La instalación de este lavavajillas requiere un nivel básico

de habilidades mecánicas, eléctricas y de plomería. La correcta instalación

del producto es responsabilidad del instalador. Si se producen fallas en el
producto debido a una instalación inadecuada, la Garantía del Producto de
GE Appliances no cubrirá las mismas. Consulte la información de la Garantía.

ŶTiempo de instalación – 1 y 3 Horas. Las instalaciones nuevas requieren más

tiempo que las instalaciones de reemplazo.

IMPORTANTE – El lavavajillas DEBE ser instalado para permitir el retiro futuro de
su ubicación, si se requiere realizar el servicio técnico.

Se deberá tener cuidado cuando el electrodoméstico sea instalado o retirado, a fin
de reducir la posibilidad de daños sobre el cable de suministro eléctrico.

Si el lavavajillas que recibió está dañado, se debería comunicar de inmediato con
su vendedor o fabricante.

Su lavavajillas es un electrodoméstico donde se calienta agua.

PRECAUCIÓN

Al realizar las instalaciones descritas en este folleto, se deben usar guantes,
gafas de seguridad o gafas protectoras.

LEA DETENIDAMENTE

2

CONSERVE ESTAS INSTRUCCIONES

Installation Preparation

DISHWASHER DRAWER
INSTALLATION OVERVIEW

This video provides an overview of what is needed to install a Dishwasher Drawer.

It is intended as an overview only of the installation process and is not intended to be used as a guide on how to install the Dishwasher Drawer yourself.

TOOLS YOU WILL NEED

Safety Glasses

Gloves

PARTS SUPPLIED IN
INSTALLATION PACKAGE

Drain hose
support (1)

Phillips

»´PP

screws (7)

Drain hose

joiner (1)

1-1/2” (38 mm)

bottom fixing

screws & metal

washers (2)

Phillips-Head

Screwdriver

Flat Head

Screwdriver

Wire clip (2)

(for securing drain

hose joiner)

Rubber washer

for inlet hose (1)

(comes already

fitted)

Pliers

(Channel Lock)

Drill and Bits

Clamp (1)

(for securing

drain hose joiner)

Moisture protection

tape (1)

(to prevent moisture

damage to cabinetry)

Flashlight

Measuring Tape

Side mounting

bracket kit

(A and B) (2)

OPTIONAL

Hexagonal
socket for feet
adjustment (2)

(long & short)

Level

Carpenter’s

Square

Top

mounting

brackets (2)

OPTIONAL

If the drain hoses supplied are not long enough to reach your services, you must use a Drain Hose Extension Kit WD24X30798 which will extend the drain hoses by 11’ 10” (3.6 m).
The kit is available from GEApplianceparts.com or by phone at 877.959.8688 during normal business hours.

NOTE: Consider recycling options for your appliance packaging material.

3

PREPARE ELECTRICAL WIRING

Installation Preparation

WARNING

FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker before
beginning installation.

Do not use an extension cord or adapter plug with this appliance.

ADVERTENCIA

PARA SEGURIDAD PERSONAL: Quite el fusible o abra el interruptor de circuitos
antes de comenzar la instalación. No utilice un cable de extensión o un enchufe
adaptador con este artefacto.

ELECTRICAL REQUIREMENTS

Be sure that the electrical connection and wire size are adequate and in conformance
with the National Electric Code, ANSI/NFPA 70 – latest edition, and all local codes
and ordinances.

This appliance must have:

• 120V, 60Hz, AC-only, 15-ampere or 20-ampere, fused electrical supply.

• Wiring must be 2 wire with ground and rated for 75°C (167°F).

• If the electrical supply does not meet the above requirements, call a licensed
electrician before proceeding.

It is recommended to have:

• A circuit breaker or time-delay fuse.

• A properly grounded individual branch circuit.

Grounding Instructions–Permanent Connection

This appliance must be connected to a grounded metal, permanent wiring system,
or an equipment-grounding conductor must be run with the circuit conductors and be
connected to the equipment-grounding terminal or lead on the appliance.

Grounding Instructions–Power Cord Models

This appliance must be grounded. In the event of a malfunction or breakdown,
grounding will reduce the risk of electric shock by providing a path of least resistance
for electric current. This appliance is equipped with a cord having an equipment­grounding conductor and a grounding plug. The plug must be plugged into an
appropriate outlet that is installed and grounded in accordance with all local codes
and ordinances.

WARNING

The improper connection of the equipment grounding conductor can result in a risk
of electric shock. Check with a qualified electrician or service representative if you
are in doubt that the appliance is properly grounded.

WARNING

For models equipped with power cord: Do not modify the plug provided with
the appliance; if it will not fit the outlet, have a proper outlet installed by a qualified
technician.

ADVERTENCIA

La conexión inadecuada del conductor de conexión a tierra del equipamiento puede

SURYRFDUXQULHVJRGHGHVFDUJDHOpFWULFD&RQVXOWHDXQHOHFWULFLVWDFDOL¿FDGRR

representante de servicio técnico si tiene dudas sobre la correcta conexión a tierra
del aparato.

ADVERTENCIA

Con los modelos equipados con cable de corriente: No modifique el enchufe
provisto con el electrodoméstico; si no coincide con el tomacorriente, solicite la
instalación de un tomacorriente apropiado a un electricista calificado.

4

Installation Preparation

OPTIONAL - HARD WIRING PRIOR TO INSTALLATION

POWER CORD OR HARDWIRE OPTION

We recommend the use of the power cord. If using the power cord option, skip steps 1-4 and
proceed to the PRODUCT DIMENSIONS section of this Installation Instructions.

If however you elect to hardwire the dishwasher drawer, follow steps 1-4 and then continue
with the rest of the Installation Instructions.

1

REMOVE THE DISHWASHER DRAWER
(

Skip step if using the power cord.)

In preparation of removing the
dishwasher drawer, so as to not strain
its rear connectors, place a sturdy box
near the installation site to rest the
drawer on after it is removed. Cover the
box with a towel to provide a protective
surface for the drawer to rest on.

Pull the dishwasher drawer out until it
stops.

1

2

4” (100 mm)

Press the release tabs in on both
sides and push them back to release
drawer from its runners.

Lift the drawer off its runners and carefully
place it upright on the covered sturdy box
you had previously positioned nearby.

Remove drawer*

3

Place on covered

sturdy box

4

Push drawer

runners back

in on both

sides

* Do not move or rest the drawer too far to

prevent strain on its rear connectors.

Rear

Connectors

5

Drawer resting

on covered

sturdy box

2

REMOVE THE ACCESS COVER AND REMOVE THE
POWER CORD (Skip step if using the power cord.

1

Clip

1

Clip

Access cover

1 With a flat-bladed screwdriver, push

in the clips and slide out the access
cover.

2 Unscrew the electronics module

cover.

3 Carefully pull out the electronics

module and rest on the chassis base
out of the way.

4 With a screwdriver, unclip the plastic

harness cover and hinge open.

5 Slide the terminal block cover

sideways to unlock and hinge open
to access the terminal block.

6 Unscrew the Live, Neutral and

Ground wires as shown.
NOTE: Only unscrew the live and
neutral terminals 2 turns. They are
fork terminals and do not require the
screws to be removed. The ground
requires the screw be removed. It is
a ring terminal. Remove the center
ground screw.

7 Unscrew the three screws on the

base as shown and remove the cord
from the product.

4

6

7

5

Terminal
block cover

Harness cover

Remove existing
power cord

7

)

3

2

Electronics
module

5

Installation Preparation

OPTIONAL - HARD WIRING PRIOR TO INSTALLATION - CONTINUED

3

TERMINATE HOUSE WIRING AS SHOWN AND REPLACE MODULE AND COVERS (Skip step if using the power cord.

WARNING

If house wiring is not 2-wire with ground, a ground must be provided by the installer.
When house wiring is aluminum, be sure to use UL-Listed anti-oxidant compound
and aluminum-to-copper connectors.

8 Fit a suitable cable clamp for the

conduit through the metal knockout.

Ensure wiring is routed through or

under housing ribs.

9 Screw down the Live, Neutral and

Ground wires correctly.

10 Push the plastic harness cover back

over. It should clip back into place

11 Fold down and slide back the

terminal block cover.

12 Refit the electronics module back

into position, being careful of wiring.

13 Replace the screw securing the

electronics module.

14 Slide the access cover back,

ensuring the 2 clips shown are fully
locked in place.

NOTE: Use copper conductors only.

IMPORTANT: Both ring terminals must be
replaced and the bare Ground wire clamped

9

IMPORTANT: Ensure
house wires are routed
UNDERNEATH all other

9

harness wiring from the
electronics module.

8

ADVERTENCIA

Si el cableado doméstico no cuenta con un cable de 2 hilos con conexión a tierra,
un instalador debe realizar una conexión a tierra. Cuando el cableado doméstico
es de aluminio, asegúrese de usar un compuesto antioxidante y conectores de
aluminio a cobre aprobados or UL.

12

14

13

11

10

)

6

Installation Preparation

OPTIONAL - HARD WIRING PRIOR TO INSTALLATION - CONTINUED

4

REFIT THE DRAWER ONTO THE RUNNERS AND CLOSE (Skip step if using the power cord.

2

Lift or rotate counter-clockwise the

Before refitting the drawer,
ensure the hoses are not
twisted and the latches at
the rear of each drawer
runner are facing
forward.

drawer back onto the drawer runners
on either side.

1

3

Release tab

4” (100 mm)

)

4

Pull the release tabs forward on both
sides 4” (100 mm). Ensure the tabs are
fully pulled forward and click into place.

7

Installation Preparation

PRODUCT DIMENSIONS

C

H

F

I

B

D

E

PRODUCT DIMENSIONS INCHES (MM)

A Overall height of product* 17-13/16” (453)

B Overall width of product 23-9/16” (599)

C Overall depth of product (excluding handle) 22-9/16” (573)

D Depth of chassis (to back of front drawer panel) 21-3/4” (553)

E Depth of drawer front panel (including handle) 3-7/16” (88)

F Height of drawer front panel 17-3/8” (442)

G Height of chassis

H Height from top of drawer front panel to top of chassis 1/8” (3)

I Ventilation gap between drawer front panels 5/16” (8)

J Maximum extension of drawer 22-3/4” (578)

*Includes 1/16” (2 mm) high bracket slots

A

SIDEFRONT

1

G

17-13/16” (453)

J

PLAN

8

Bracket slots

PLAN

Installation Preparation

CABINETRY DIMENSIONS

L

K

M

SIDE

CABINETRY DIMENSIONS INCHES (MM)

K Inside height of cavity* Min. 17-15/16” (456)

L Inside width of cavity 23-5/8” (600)

M Inside depth of cavity Min. 22-13/16” (580)

Minimum clearances from adjacent cabinetry

Min. 1/2” (13 mm)
clearance from a
corner cabinet

Min. 1/16” (2 mm)
clearance to adjacent
cabinet door

9

COUNTERTOP

Installation Preparation

CAVITY PREPARATION

3/8”
(10 mm)

Moisture
protection
tape must be
applied.

These marks indicate formed
bracket screw locations, if
securing by drawer removal.

If there is no side partition, you
can construct timber bracing as
something to secure into.

IMPORTANT

Incorrect placement of the
hole will result in damage to
hoses.

Max. 1/4” (5 mm)

Max. distance between
hole edge and rear
inner face

Max. 1/2” (10 mm)

Max. distance between
hole edge and floor

Ø 1-1/2”
(38 mm)

Max. 17-11/16”

Ø max. 1-1/2”

(38 mm)

(450 mm)

Service Hole

Can be located on either side of dishwasher, close to the rear face and the
shelf, as illustrated.

Ŷ

If the hole is through wood, make sure its edges are smooth and rounded.

Water Connection

Recommended HOT
(Maximum 140°F/60°C).

Supplied hose to

VXLW»´PPPDOH

compression fitting.

Water Pressure

Max. 1 MPa (145 psi)
Min. 0.03 MPa (4.3 psi)

Min. 7-7/8” (200 mm)

IMPORTANT

The power outlet must be
located in a cabinet adjacent
to the dishwasher cavity.

110-120 VAC max. 15 A

10

Installation Preparation

MAXIMUM DISTANCE OF HOSES AND CORD FROM CHASSIS EDGE

LEFT HAND SIDE RIGHT HAND SIDE

Drain hoses - 78-1/2” (2000mm)

Drain hoses - 70-1/2” (1800mm)

Inlet hose - 64-3/4” (1650mm)

Power cord (excluding plug) -

78-1/2” (2000mm

Inlet hose - 49” (1250mm)

)

Power cord (excluding plug) -

78-1/2” (2000mm

)

11

Installation Instructions

CHOOSE WHICH INSTALLATION METHOD (A) OR (B) IS MOST SUITABLE FOR YOUR CABINETRY

A

RECOMMENDED METHOD (A) - SECURE WITHOUT DISHWASHER DRAWER REMOVAL

(FRAMELESS CABINETRY ONLY)

OPTION A - RECOMMENDED

A1

ATTACH SIDE MOUNTING BRACKETS

Clip all four side mounting brackets

into their slots using a flat-bladed

screwdriver. Ensure they’re securely

B

A

fitted before sliding product into cavity.

B

A

A

B

The mounting slots are in pairs, one

on each side diagonally across the

product. A bracket must match A slot

and B bracket must match B slot.

When fitting brackets, ensure the
ends are not pushed down into
the chassis.

A2

PULL HOSES THROUGH AND PUSH UNIT INTO THE

CAVITY

Optional - Attach the
two top mounting
brackets

A

B

IMPORTANT

If product cannot be pushed in far enough,
pull it out again and rearrange hoses and cord.

Do not use excessive force, as doing so may
pinch the hoses and lead to incorrect operation.

(x2)

Initially level the product

When fitting brackets,
ensure the ends are not
pushed down into the
chassis.

As you push product in,

pull through hoses and

cord, ensuring they don’t

get kinked or twisted.

12

Installation Instructions

OPTION A - RECOMMENDED (CONTINUED

A3

SECURE TO THE SIDE CABINETRY - OPTION

Open the
drawer
halfway.
Using a
flat bladed
screwdriver,
pry the
grey rubber
plug out
of the trim
moulding.

Using a small
Phillips
screwdriver,
screw
through the
trim moulding,
securing the
side mounting
bracket to the
cabinetry.
Do not damage
the rubber trim seal.

1

2

3

4

Replace the
grey rubber
plug back
into the trim
moulding
and ensure
the trim seal
is facing
forward.

Repeat for all
four brackets.

)

SECURE TO THE ABOVE CABINETRY - OPTION

The top mounting brackets

(x2)

will only bend upwards a

maximum of 3/8” (10 mm).

13

Installation Instructions

CHOOSE WHICH INSTALLATION METHOD (A) OR (B) IS MOST SUITABLE FOR YOUR CABINETRY

B

ALTERNATE METHOD (B) - SECURE BY REMOVING THE DISHWASHER DRAWER

OPTION B - ALTERNATE METHOD

B1

PULL HOSES THROUGH AND PUSH UNIT INTO THE
CAVITY

Optional - Attach the
two top mounting
brackets

(x2)

Initially level the product

IMPORTANT

If product cannot be pushed in far enough,
pull it out again and rearrange hoses and cord.

Do not use excessive force, as doing so may
pinch the hoses and lead to incorrect operation.

When fitting brackets,
ensure the ends are not
pushed down into the
chassis.

As you push product in,

pull through hoses and

cord, ensuring they don’t

get kinked or twisted.

B2

REMOVE THE DISHWASHER DRAWER

In preparation of removing the
dishwasher drawer, so as to not strain
its rear connectors, place a sturdy box
near the installation site to rest the
drawer on after it is removed. Cover the
box with a towel to provide a protective
surface for the drawer to rest on.

Pull the dishwasher drawer out until it
stops.

Lift the drawer off its runners and carefully
place it upright on the covered sturdy box
you had previously positioned nearby.

Remove drawer*

3

Place on covered

sturdy box

1

* Do not move or rest the drawer too far to

prevent strain on its rear connectors.

2

4” (100 mm)

Press the release tabs in on both
sides and push them back to release
drawer from its runners.

5

Drawer resting

on covered

sturdy box

4

Push drawer

runners back

in on both

sides

Rear

Connectors

14

Installation Instructions

OPTION B - ALTERNATE METHOD (CONTINUED

B3

SECURE TO THE SIDE CABINETRY

The product has three pairs of fixing points:

Ensure the sound insulation

is repositioned correctly

1

Two pairs of formed brackets on either side

of the chassis (use 5/8” (16mm) screws)

B4

REFIT THE DRAWER ONTO THE RUNNERS

2

Lift the drawer back onto the drawer runners on both sides.

)

2

A pair of fixing holes

either side on the

bottom (use 1-1/2”

(38mm) fixing screws

and washers)

4

4” (100mm)

Before refitting the
drawer, ensure
the hoses are not
twisted and the
latches at the rear
of each drawer
runner are facing
forward.

3

1

Release tab

Slip your finger under the slide and pull
the release tabs forward 4” (100mm)
on both sides. Ensure the tabs are fully
pulled forward and click into place.

15

Installation Instructions

THERE ARE THREE DIFFERENT PLUMBING AND DRAINAGE OPTIONS - CHOOSE WHICH IS MOST SUITABLE

DRAINAGE OPTION 1 - Dishwasher and Ø 1-1/2” (38 mm) Standpipe

Screw Drain hose

support to back wall at

correct height.

If space is limited

for fixing, push

hose through drain

hose support

to required height.

2

Max.

4-3/4”

(120
mm)

1

29-1/2”-34-3/4”

(750-883 mm)

1-1/2”
(38 mm)

NOTE: See,
the “CONNECT
INLET HOSE TO
HOT WATER”
step.

29-1/2 - 34-3/4” (750-883 mm)

Min. 19-11/16” (500 mm)

IMPORTANT

Ensure that drain hose is installed
as close to the underside of the
countertop as possible. This will
ensure no waste re-enters the drain
hose in the event of poor flow or a
blockage in the plumbing.

Ensure the drain hose does not extend
into water retained in the trap; an air gap
is required to prevent waste water from
siphoning back into the tub.

IMPORTANT

Ensure that drain connection
will comply with local plumbing
regulations.

16

Min. R 8”
(200 mm)

Installation Instructions

THERE ARE THREE DIFFERENT PLUMBING AND DRAINAGE OPTIONS - CHOOSE WHICH IS MOST SUITABLE

DRAINAGE OPTION 2 - Dishwasher using Air Gap with Drain Hose Joiner

IMPORTANT

We recommend the use of a
commercially available Air Gap Kit.

When installing two single drawers,
this provides totally separate draining
for each drawer and eliminates
possible cross draining problems

Air Gap

IMPORTANT

Ensure that drain connection
will comply with local
plumbing regulations.

Secure drain hose

to air gap

Drain
hose

2

1

NOTE: See,

the “CONNECT
INLET HOSE TO
HOT WATER”
step.

37-3/8” (950 mm)
Max. height to top of
air gap (countertop

or wall mounted)

Min. R 8”
(200 mm)

17

Installation Instructions

THERE ARE THREE DIFFERENT PLUMBING AND DRAINAGE OPTIONS - CHOOSE WHICH IS MOST SUITABLE

DRAINAGE OPTION 3 - Dishwasher using drain hose joiner onto sink trap/waste tee

Screw Drain hose

support to back wall at

correct height.

If space is limited

for fixing, push

hose through drain

hose support

to required height.

Supplied drain hose joiner to suit
Ø 3/4” (19 mm) waste tee

Max.

4-3/4 “

2

(120 mm)

NOTE: See,
“CONNECT
INLET HOSE
TO HOT
WATER”.

29-1/2”-34-3/4”

(750-883 mm)

1

3

Ensure drain hose is routed

straight to the joiner so that waste

water does not accumulate in the
hose. Remove excess drain hose

material if necessary.

18

IMPORTANT

Ensure that drain connection
will comply with local
plumbing regulations.

Min. R 8”

(200 mm)

Do not shorten the inlet hose.

29-1/2 - 34-3/4” (750-883 mm)

Min. 19-11/16” (500 mm)

Installation Instructions

CONNECT WATER AND SWITCH DISHWASHER ON

CONNECT INLET HOSE TO HOT WATER

o

180

Ensure the
supplied rubber
washer is fitted
inside the coupling.

1

Tighten coupling

with spanner.

No leaks!

2

SWITCH PRODUCT ON

TROUBLESHOOTING

Ŷ

Excessive water remaining above the filter plate, after the rinse cycle. (This is displayed as an A3 fault. See Owner’s Manual, “How to attend to a fault”.)

Check for a kinked drain hose, blocked or incorrectly drilled out waste connection, highloop not properly installed, drain hose not routed correctly or spray arms not in place.

Ŷ

No water supply. (This is displayed as an A1 fault. See Owner’s Manual, “How to attend to a fault”.)

Check water is connected and turned on.

Ŷ

The dishwasher is beeping continuously
There is a fault. See Owner’s Manual, “How to attend to a fault” for further information and instructions.

Ŷ

No program indicator lights up when the drawer is opened

Ensure power is connected and is switched on. If it is and still no indicator lights up, see the “Preference Options” section of the Quick Start Guide.
An option called ‘Open drawer auto power-on’ may need to be turned on.

Ŷ

Water around water supply and drainage connections

Check connections, existing plumbing and hoses for leaks. Check rubber washer and hose clamp are correctly fitted.

Ŷ

If product is tipping

Ensure the product is secured to the cabinetry.

Ŷ

If front panels are misaligned

Check and re-level product. Check the cabinetry is square. For Integrated models, check and adjust front panel alignment if necessary.

Ŷ

Drawer doesn’t close properly

Ensure nothing is obstructing the drawer from closing properly such as hoses or drawer latches.

Ŷ

If a problem occurs, consult the ‘Troubleshooting’ section of the User guide.

Ŷ

If after checking these points you still need assistance, please refer to the Owner’s Manual for warranty details and your nearest Authorized Service Center, or
contact us through our website, listed below.

19

TO BE COMPLETED BY THE INSTALLER

Installation Instructions

FINAL CHECKLIST

Check all parts are installed.

Ŷ

Ensure that all panels and parts are secure and final electrical tests have been

Ŷ

conducted in accordance with local electrical regulations.

Ensure product is level, securely fastened to the cabinetry and opens and

Ŷ

closes freely. The drawer must be free to fully close with no resistance from the
cabinetry.

Ensure inlet hose to water supply has supplied rubber washer fitted and that it

Ŷ

is tightened a further half turn after seal contact.

Ensure any knockouts or plugs in drain connection have been drilled out and

Ŷ

drain connection has been made.

The drain hose joiner must not support the weight of excess hose material.

Ŷ

Keep drain hose as fully extended as possible to prevent sagging. Any excess
length of drain hose should be kept on the dishwasher side of the highloop.

If connecting the drain hose to the sink trap, ensure the highloop is a minimum

Ŷ

6” (150 mm) higher than the drain hose joiner.

Ensure any packaging or tape securing the racks or spray arms is removed

Ŷ

from the drawer.

Water softener models only: adjust the water softener setting from the default

Ŷ

setting to suit the water hardness of the area. See the Quick Start Guide and
section “Water softener” in the Owner’s Manual.

Turn on the power and water supplies, then open the drawer. You should hear a

Ŷ

beep and see a program indicator light up on the internal control panel.

Check the spray arms are in place, mounted correctly and free to rotate, by

Ŷ

physically rotating by hand.

Add three cups of water into the drawer. Press until the indicator of the Rinse

Ŷ

program lights up. Close the drawer and press

After the Rinse program has finished, ensure the dishwasher has run and

Ŷ

drained correctly.

Check the water supply has correctly shut off and the drainage connection for

Ŷ

leakage.

to start the program.

Spray
arm

Printed in Thailand

20

519702

31-4000292 Rev 0 12-23 GEA