Cafe CAFRERADWRH1024, CAFRERADWRH1222 Installation manual

SAFETY INFORMATION ..............3
USING THE KITCHEN HUB
Hardware .................................5
Control Features ...........................5
Wi-Fi Connect ............................ 6
Chef Connect ............................ 6
CARE AND CLEANING
Filters ....................................7
Surfaces ..................................8
INSTALLATION INSTRUCTIONS ... 9
Mounting Plate ...........................14
Installation Types .........................17
A. Outside Top Exhaust ..................18
B. Recirculating ........................ 22
C. Outside Back Exhaust ................ 25
TROUBLESHOOTING TIPS ......... 28
LIMITED WARRANTY .............. 29
ACCESSORIES ...................... 30
CONSUMER SUPPORT ............. 32
OWNER’S MANUAL &
INSTALLATION
INSTRUCTIONS
UVH1301
Write the model and serial numbers here:
Model # _________________
KITCHEN HUB
GE is a trademark of the General Electric Company. Manufactured under trademark license.
Serial # _________________
You can find them on a label on the inside of the unit behind the filters.
Para consultar una version en
instrucciones, visite nuestro sitio de
internet GEAppliances.com.
49-2000492 Rev. 0 01-19 GEA
ESPAÑOL
THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.
Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.
We take pride in the craftsmanship, innovation and design that goes into every GE Appliances
product, and we think you will too. Among other things, registration of your appliance ensures that we
can deliver important product information and warranty details when you need them.
Register your GE appliance now online. Helpful websites and phone numbers are available in the
Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration
card included in the packing material.
2 49-2000492 Rev. 0
IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING
SAFETY INFORMATION
WARNING
ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the manufacturer.
B. To avoid the risk of scald injury from a hot cooktop,
keep young children away from the touchscreen.
C. Before servicing or cleaning unit, switch power off
at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
D. Do not use this unit with any solid-state speed
control device.
E. This unit must be grounded.
CAUTION
ONLY. DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS AND VAPORS.
CAUTION
TO PROPERLY EXHAUST AIR, BE SURE TO DUCT AIR OUTSIDE. DO NOT VENT EXHAUST AIR INTO SPACES WITHIN WALLS OR CEILINGS OR INTO ATTICS, CRAWL SPACES OR GARAGES.
TO REDUCE THE RISK OF FIRE,
FOR GENERAL VENTILATING USE
TO REDUCE RISK OF FIRE AND
WARNING
TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:
A. SMOTHER FLAMES with a close-fitting lid, cookie
sheet or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
B. NEVER PICK UP A FLAMING PAN—You may be
burned.
C. DO NOT USE WATER, including wet dishcloths or
towels—a violent steam explosion will result.
D. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher, and you already know how to operate it.
2. The fire is small and contained in the area where it started.
3. The fire department is being called.
4. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety” published by NFPA.
WARNING
RANGE TOP GREASE FIRE:
A. Never leave surface units unattended. Boilovers
cause smoking and greasy spillovers that may ignite. Heat oils slowly on medium settings.
B. Always turn fan ON when cooking at high heat or
when flambéing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
C. Clean ventilating fans frequently. Grease should not
be allowed to accumulate on fan or filter.
D. Use proper pan size. Always use cookware
appropriate for the size of the surface element.
TO REDUCE THE RISK OF INJURY
TO REDUCE THE RISK OF A
READ AND SAVE THESE INSTRUCTIONS
49-2000492 Rev. 0 3
IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
This device contains licence-exempt transmitter(s)/
SAFETY INFORMATION
receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including
interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
1) L’appareil ne doit pas produire de brouillage;
2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation.
To ensure compliance, operations at closer than this distance is not recommended.
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Ŷ 5HRULHQWRUUHORFDWHWKHUHFHLYLQJDQWHQQD
Ŷ ,QFUHDVHWKHVHSDUDWLRQEHWZHHQWKHHTXLSPHQWDQG
receiver.
Ŷ &RQQHFWWKHHTXLSPHQWLQWRDQRXWOHWRQDFLUFXLW
different from that to which the receiver is connected.
Ŷ &RQVXOWWKHGHDOHURUDQH[SHULHQFHGUDGLR79
technician for help.
Les antennes installées doivent être situées de facon à ce que la population ne puisse y être exposée à une distance de moin de 20 cm. Installer les antennes de facon à ce que le personnel ne puisse approcher à 20 cm ou moins de la position centrale de l’ antenne.
La FCC des éltats-unis stipule que cet appareil doit être en tout temps éloigné d’au moins 20 cm des personnes pendant son functionnement.
Limited by local law regulations, version for North America does not have region selection option.
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
Les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.
How to Remove Protective Shipping Film and Packaging Tape
Carefully grasp a corner of the protective shipping film with your fingers and slowly peel it from the appliance surface. Do not use any sharp items to remove the film. Remove all of the film before using the appliance for the first time.
4 49-2000492 Rev. 0
To assure no damage is done to the finish of the product, the safest way to remove the adhesive from packaging tape on new appliances is an application of a household liquid dishwashing detergent. Apply with a soft cloth and allow to soak.
NOTE: The adhesive must be removed from all parts. NOTE: For further cleaning instructions/suggestions,
please refer to the Care And Cleaning section.
Hardware
Hulu
1HWÀL[
3OD\0RYLHV«
6SRWLI\
Blue Apron
Recipes
Entertainment
Skype
U+ Connect
Google
Music
8:50
Screen
Front
Camera
Monday
Swipe up on the screen
to access controls.
25 °F | L
USING THE KITCHEN HUB: Hardware / Contol Features
RXLVYLOOH
Speaker
, February 12
Volume Button
On/Off
Cooktop Camera
Control Features
34 57 8 9
1
FAN
OFF LOW MED HIGH BOOST
26
1. Ventilation Fan and Light Control Screen
2. FAN: Speed control for fan. Tap LOW for LOW
speed. MED for MEDIUM speed and HIGH for HIGH speed. Tap BOOST for BOOST speed.
3. Camera: Select to take a picture of your cooking surface.
4. Microphone: Select to mute/unmute.
5. Notification: Select to turn notification sounds on
and off.
Lights
LIGHT
OFF DIM HIGH
6. LIGHT: Light level control. Tap DIM for low light, MED for medium light, and HIGH for bright light.
7. Lock: Select to lock screen controls.
8. Volume: Slide to increase or decrease media
volume.
9. Brightness: Slide to increase or decrease screen brightness.
For Android device setup, and for Android help, please reference the Setup Wizard on the Kitchen Hub.
49-2000492 Rev. 0 5
USING THE KITCHEN HUB
Connecting your WiFi Connect Enabled Appliance
Your GE Appliances Kitchen Hub is recommended to be connected to WiFi.
Heat Sensor
This unit is equipped with a heat sensor that will activate the ventilation FAN if excessive temperatures are detected above the cooktop surface to protect the Kitchen Hub components from overheating.
Screen Moisture Protection System
Your Kitchen Hub is equipped with a screen protection system. The system expels small amounts of air around and below the screen to keep the touchscreen area dry and clean by preventing condensation or other substances during cooktop operation.
Use the Setup Wizard to connect unit to WiFi.
If FAN is OFF and excessive temperature is detected, the FAN will automatically turn to LOW speed. You may adjust FAN speed to MEDIUM, HIGH, or BOOST, but you will not be able to turn to OFF until temperatures return to an acceptable level.
The system is on while the screen is in the awake state and off when the screen is in screensaver mode or off position. Operating the cooktop while screen protection system is off may result in condensation on the touchscreen. It is recommended to activate screen during cooking to prevent this from happening. If condensation build up continues while protection system is active, turn the ventilation FAN on to provide additional protection.
USING THE KITCHEN HUB: WiFi / Heat Sensor / Screen Moisture Protection
6 49-2000492 Rev. 0
Filters
Be sure the circuit breaker is off and all surfaces are cool before cleaning or servicing any interior part of the unit.
Metal Grease Filter
The metal filters trap grease during cooking.
The filters must ALWAYS be in place when the unit is in use. The grease filters are dishwasher-safe and should be cleaned every month, depending on the usage of the unit.
To remove:
Press on the filter handle to disengage the filter lock to release the filter.
To replace:
Fit the tabs at the bottom of the filter into the slots in the back of the filter opening. Lift up the front side of the filter and push gently until the filter locks into place. Make sure the filter lock is in the closed position to secure the filter.
To clean:
Swish the filter in hot soapy water and rinse in clean water or wash it in the dishwasher. Do not use abrasive cleansers.
NOTE: Some discoloration of the filter may occur in the dishwasher.
Metal Grease Filter
USING THE KITCHEN HUB: Filters
Charcoal Filter (for recirculation installation only)
If the model is not vented to the outside, the air needs to be recirculated through a disposable charcoal filter that helps remove smoke and odors.
NOTE: DO NOT rinse, or put charcoal filter in an automatic dishwasher.
The charcoal filters are included with the unit. They cannot be cleaned. It is recommended that the charcoal filter be replaced every 6 months or if it is noticeably dirty or discolored.
Order Charcoal Filter UXCF91
To inquire about purchasing replacement charcoal filters or to find the location of a dealer nearest you, please call our toll-free number:
National Parts Center 800.626.2002
To install:
1. Remove the metal filters—see Metal Grease Filter section.
2. Install the charcoal filter mounts to either side of the motor.
3. Insert the snap on the charcoal filter into the center on the mount.
4. Clip the charcoal filter in until it is locked.
5. Repeat with second filter on the other side of the motor.
6. Replace the metal filters - See Metal Grease Filter section.
To remove:
1. Remove the metal filters—see Metal grease filter section.
2. Remove the charcoal filter on each side of the blower.
Charcoal Filter Mount
49-2000492 Rev. 0 7
Surfaces
Stainless Steel Surfaces (on some models)
Do not use a steel wool pad; it will scratch the surface.
To clean the stainless steel surface, use warm sudsy water or a stainless steel cleaner or polish. Always wipe the surface in the direction of the brush line. Follow the cleaner instructions for cleaning the stainless steel surface. Cleaners with oxalic acid such as Bar Keepers Friend Soft Cleanser™ will remove surface rust, tarnish, and small blemishes. To receive a coupon for a trial sample of Bar Keepers Friend Soft Cleanser™ follow the link below or scan the QR Code.
barkeepersfriend.com/ge
Painted Surfaces and Black Stainless Color (on some models)
Do not use a steel wool pads or other abrasive cleaners; they will scratch the surface.
CARE AND CLEANING: Surfaces
Clean grease-laden surfaces frequently. To clean the outer surface, use a hot, damp cloth with a mild detergent suitable for painted surfaces. Use a clean, hot, damp cloth to remove soap. Dry with a dry, clean cloth.
Use only a liquid cleanser free of grit and rub in the direction of the brush lines with a damp soft sponge.
To inquire about purchasing stainless steel appliance cleaner or polish, or to find the location of a dealer nearest you, please call our toll-free number:
National Parts Center
800.626.2002
GEApplianceParts.com
NOTE: When cleaning, take care not to come in contact
with filters and other surfaces.
How to Clean the Outside
We recommend against using cleaners with ammonia or alcohol, as they can damage the appearance of the appliance. If you choose to use
a common household cleaner, first apply the cleaner directly to a clean cloth, then wipe the soiled area.
Case
Clean the outside of the appliance with a sudsy cloth. Rinse and then dry. Do not use appliance wax, polish, bleach or products containing chlorine on Stainless Steel finishes.
Screen
Wipe with a damp cloth or glass cleaner such as Windex. Dry thoroughly. Do not use large amounts of soap and water, sharp objects or abrasives - they can damage it.
Bottom
Clean off the grease and dust on the bottom often. Use a solution of warm water and detergent.
Cooktop Camera
Use a dry, soft cloth to clean the cooktop camera.
8 49-2000492 Rev. 0
INSTALLATION INSTRUCTIONS
Installation
Kitchen Hub
UVH1301
Instructions
“If you have questions, call GE Appliances at 800.GE.CARES (800.432.2737)
or visit our website at: GEAppliances.com”
BEFORE YOU BEGIN
Read these instructions completely and carefully.
Ŷ
IMPORTANT — Save these
instructions for local inspector’s use.
Ŷ
IMPORTANT — Observe all governing
codes and ordinances.
Ŷ
Note to Installer – Be sure to leave these
instructions with the Consumer.
Ŷ
Note to Consumer – Keep these instructions for
future reference.
Ŷ
Skill level – Installation of this appliance requires
basic mechanical and electrical skills.
Ŷ
Completion time – Approximately 1 to 3 hours
Ŷ
Proper installation is the responsibility of the
installer.
Ŷ
Product failure due to improper installation is not
covered under the Warranty.
WARNING
ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
A. Installation work and electrical wiring must be
done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.
B. Sufficient air is needed for proper combustion
and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guidelines and safety standards such as those published by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
C. When cutting or drilling into wall or ceiling, do
not damage electrical wiring and other hidden utilities.
D. Ducted fans must always be vented to the
outdoors.
TO REDUCE THE RISK OF FIRE,
E. When applicable, install any makeup
(replacement) air system in accordance with local building code requirements. Visit GEAppliances. com for available makeup air solutions.
WARNING
USE ONLY METAL DUCT WORK.
TO REDUCE THE RISK OF FIRE,
49-2000492 Rev. 0 9
Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.
WARNING
a risk of electric shock.
Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded. Do not use an extension cord. If the power supply cord is too short, have a qualified electrician install an outlet near the appliance.
INSTALLATION INSTRUCTIONS
Where a standard two-prong wall receptacle is encountered, it must be replaced with a properly grounded three-prong wall receptacle, installed by a qualified electrician.
WARNING
Can cause injury or death: DO NOT, under any circumstances, cut, deform or remove any of the prongs from the power cord. Failure to comply may cause fire.
Improper grounding can result in
Risk of Electric Shock.
ELECTRICAL REQUIREMENTS
120 V Models
This product requires a three-prong grounded outlet. Product rating is 120 volts AC, 60 Hertz. This product must be connected to a supply circuit of the proper voltage and frequency. Wire size must conform to the requirements of the National Electrical Code or the prevailing local code. The outlet box should be located in the cabinet above the unit and away from any potential ducting. The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electrical Code or the prevailing local code.
CAUTION
mounting surface must be capable of supporting the cabinet load of this 75 pound product.
CAUTION
cannot be installed in cabinet arrangements such as an island or a peninsula. It must be mounted to BOTH a top cabinet AND a back wall.
CAUTION
injury (back injury or other injuries due to excessive weight of the product) or property damage, you will need two people to install this product.
For personal safety, the
For personal safety, this product
To avoid the risk of personal
10 49-2000492 Rev. 0
Loading...
+ 22 hidden pages