Cadent MA14731 Users Manual

EID-2 Optical Impression Device

Operation Manual

iTero Mobile Cart

Publication SD08300-A

Revision 1.05

December 26, 2006

Optical Impression System for Computer Assisted Design and Manufacturing

(510K exempt under 21 CFR 872.3661)

DIGITAL IMPRESSION DEVICE

EID-2 Optical Impression Device Operation Manual

COPYRIGHT

Copyright © by Cadent. 1995-2006. All rights reserved.
The hardware and software described in this document are supplied under a Sales and Services

Agreement and may be used only in accordance with the terms of that agreement.
The information contained in this document is subject to change without notice.
No part of this document may be reproduced, photocopied, stored in a retrieval system, or transmitted in

any manner (electronic or mechanical) for any purpose other than the customer’s normal usage, without
the prior written permission of Cadent.

TRADEMARKS

Cadent, OrthoCAD, iTero, EID-1, EID-1 Optical Impression Device, EID2, EID-2 Optical Impression
Device, OrthoCAD iQ, OrthoCAD Set-Up, OrthoCAD Bracket Placement and OrthoCAD Bracket
Placement Video System are trademarks or registered trademarks of Cadent.

Any other trademarks and registered trademarks appearing in this manual are the property of their
respective owners.

CONTACT US

Cadent, Inc.

640 Gotham Parkway Carlstadt NJ, 07072-2405 USA

Phone: [phone]
Fax: [phone]
Email: [e-mail]

www.cadent.biz

2 Publication SD08300-A (Rev. 1.05)

Operation Manual EID-2 Optical Impression Device

SYMBOLS

Caution! - Wherever this symbol appears on the equipment, it is recommended to refer

to the instructions in this Operator’s Guide.

Applied part type B. Any device on which this symbol appears is electric isolation type B.

CLASS 1 LASER COMPLIANCE

This product complies with “21 CFR 1040.10” and “EN 60825-1”.

MEDICAL SAFETY COMPLIANCE

This equipment complies with the medical safety standard UL 60601.

FCC Compliance

This device complies with part 15 of FCC Rules, and operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause undesired
operation.

FCC Warning

Modifications to the equipment that are not expressly approved by the manufacturer may void your
authority to operate the equipment under FCC Rules.

December 26, 2006 3

EID-2 Optical Impression Device Operation Manual

WARNINGS

POWER

 An internal battery backup unit will supply AC power to the system in the event of a power shortage.

Therefore, power is present in the internal hardware components even when the system is unplugged
from the wall. To ensure that power is removed from all components, follow these instructions:

 Close all files and applications.
 Press the front POWER switch to shutdown the system.
 Unplug power cable from the wall socket.
 Press the MAIN POWER SHUT OFF switch on the back of the cart (see page 14).

 To restore power, press the MAIN POWER SHUT OFF switch again and the system will beep to

indicate return of power.

 According to Department of Transportation (DOT) regulations, the system must be shipped with

internal battery leads disconnected. Please note that battery leads should be disconnected and
reconnected by authorized Cadent technicians only.

 Power is supplied to the system via an isolation transformer.

WIRELESS LAN

 The EID-2 system comes equipped with a Wireless LAN unit. Using standard wired communications

will violate the AC mains power isolation.

SCANNER

 The scanner emits red laser light for performing a tooth scan (660 nm Class 1). Normal usage of the

scanner does not present any danger to the eye. However, you should refrain from shining the light
directly into the patient’s eyes.

 The scanner also emits colored lights for performing a colored scan. This light does not present any

danger to the eyes.

 Avoid stepping or rolling over the scanner cable.
 The scanner head contains fragile parts and should always be handled with care. Be sure to read

“Disinfecting Scanner and Replacing Disposable Sleeve” on page 11 before beginning to scan patient
cases.

GENERAL

 Be careful not to block any of the air vents on the cart (see page 14).
 Refrain from opening any closed components. Except for the replacement of batteries in the mouse

and foot pedal, all closed components should be serviced by authorized Cadent technicians only.

 The EID-2 system is intended for indoor usage only and should not be exposed to direct sunlight.
 Due to its weight, the EID-2 system should be lifted and loaded by two or more persons.

4 Publication SD08300-A (Rev. 1.05)

Operation Manual EID-2 Optical Impression Device

Table of Contents

Chapter 1: Introduction .......................................................................................................... 7

Overview................................................................................................................................ 7

The Digital Crown Production Process................................................................................... 7

About the iTero Service.......................................................................................................... 8

Chapter 2: Operating Instructions......................................................................................... 9

First Time Usage.................................................................................................................... 9

Booting System...................................................................................................................... 9

Shutting Down System........................................................................................................... 9

Unplugging System for Short Intervals.................................................................................... 9

Automatic Shutdown............................................................................................................... 9

Using the iTero Software.......................................................................................................10

Using the Handheld Scanner.................................................................................................10

Disinfecting Scanner and Replacing Disposable Sleeve........................................................11

Using the Foot Pedal Unit......................................................................................................12

Chapter 3: Cart Features.......................................................................................................13

Front View of Cart .................................................................................................................13

Back View of Cart..................................................................................................................14

Main Power Shut Off For Shipping or Storage.......................................................................14

Restoring Power after Shipping or Storage............................................................................14

Cleaning Monitor...................................................................................................................15

Locking Wheels.....................................................................................................................16

Appendix A: Hardware Specifications..................................................................................17

December 26, 2006 5

EID-2 Optical Impression Device Operation Manual

This page is intentionally blank.

6 Publication SD08300-A (Rev. 1.05)