Caddy TF-603 User Manual
CADDY CORPORATION
Air SystemsFood Service Equipment
Hot Food Caddys
PROJECT:
ITEM NO:
LOCATION:
Hot Food Caddys
Open or Heated Base / Regular or Slimline
General Specifications
Hot Food Caddy to be Caddy Corporation model
TF-_______________.
Unit to have all stainless steel exterior. Top to be 18 gauge
stainless steel turned down into 2" wide channel edges, with
corners welded. Openings for hot food wells to be die
formed with 1" wide, raised pan rest around perimeter of
opening. Pan rest to be
1
8
" above table top and turned down
into food wells. Joints between top and wells to be provided
with moisture and thermal breaker.
Hot food wells to measure 12" x 20" x 6
3
8
" deep, of seamless
drawn stainless steel with cove corners, fully insulated and
encased in separate metal housing. Each hot food well to
be provided with a heating element of not less than 1 KW,
hi-heat thermostatic limit switch, pilot light and infinite heat
control allowing operator to select and stabilize any level of
holding heat from 0 to maximum input. Infinite heat control
and pilot light for each well to be recessed in
easy-to-observe tilted front panel. Wells to be for moist and
dry heat operation and to accommodate full or partial size
pans up to 6" deep.*
Frame structure to consist of 18 gauge stainless steel
formed pedestals to be reinforced with 16 gauge stainless
steel channels, to have full height extruded plastic vertical
bumpers. Casters are to be 4" diameter heavy duty, double
ball bearing, swivel type with polyurethane tires. Two
casters to be provided with foot brakes. Unit to be
completely wired and provided with a 6'-0" long cord and
plug located on side specified at time of order.
page 1 of 7
R
All specifications subject to change without notice
There's a Hot Food Caddy for every requirement in the serving of hot foods. Mobile units are available
in open or heated base models in both regular units (26" wide) and slimline units (18" wide). All units
can be used singly or in any combination for maximum efficiency in serving each meal.
Continue specifications for
Heated Base Models
Lower food storage compartments constructed of 20 gauge
stainless steel, fully insulated and enclosed with hinged
door, recessed finger grip and automatic latch.
Compartments to be heated with stainless convector type
heat of not less than 350 W complete with infinite heat
control and pilot light to be mounted and recessed in an
easy-to-observe tilted front panel. Each compartment fitted
on inside with a stainless steel wire pan frame with four pan
slides on 3" centers. Pan slides to accommodate standard
12" wide food pans and to be removable, without the use of
tools, for cleaning.
All Hot Food Caddys feature:
Full height vertical corner bumpersInsulated hot food wells with individual heat control pilot light and thermostatic limit
switchTilted control panel for easy operation Heavy duty, double ball bearing swivel casters with polyurethane tires.
Heated Base Models also feature:
Heated compartments with temperature control and pilot light
Each compartment holds four full size 2
1
2
" deep food pans
Pan slides remove easily without tools for cleaning and storage of 4" and 6" deep pans
REGULAR
STRAIGHT
(TF-604 & TF-624 Shown) (TF-614 & TF-634 Shown)
(TF-616 & TF-636 Shown)
FULL CONVENIENCE
REGULAR
U-SHAPED
(TF-606-U & TF-626-U Shown)
REGULAR
L-SHAPED
(TF-604-L & TF-624-L Shown)
* Pans and covers not included.
(TF-615-U & TF-635-U Shown)
SLIMLINE
U-SHAPED
SLIMLINE
STRAIGHT
SLIMLINE
L-SHAPED ROTATED WELL
(TF-613-R-R & TF-633-R-R Shown)
SLIMLINE
L-SHAPED
(TF-613-R & TF-633-R Shown)
CADDY Food Service Systems
509 Sharptown Road P.O. Box 345
Bridgeport, NJ 08014-0345
Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
CADDY CORPORATION
08/08
CADDY Food Service Systems
page 2 of 7
Hot Food Caddys
R
Unit to be provided with the following accessories:
(excluding TF-616 & TF-636 units)
Accessories
Folding Tray Slide - To be1" square 16 gauge stainless
steel tubing, 10" overall width, welded to intermediate lateral
supports and mounted on control side on folding brackets.
Slide to be removable.
26" wide units
18" wide units
Folding Work Shelf - 16 gauge stainless steel with all
edges turned down and welded corners, 10" overall width,
mounted on control side on folding brackets. Shelf to be
removable.
26" wide units
18" wide units
Open or Heated Base / Regular or Slimline
2 Well 3 Well 4 Well
A-68
A-88
A-69
A-89
A-70
2 Well 3 Well 4 Well
A-72
A-90
A-73
A-91
A-74
Push Handle - To be 1" O,D. 16 gauge stainless steel
tubing with two 16 gauge stainless steel support brackets
and 3" neoprene donut bumpers. Specify which end, when
facing control panel, at time of order.
26" wide units
18" wide units
ACC-52 - Vertical corner bumpers only. Easy to replace.
(Add 1
ACC-22 - Removable stainless steel well liner for easy
draining and cleaning. One required for each well.
TF-616 & TF-636 units to be provided with the following
accessories:
Accessories
ITEM NO:
PROJECT:
LOCATION:
A-15
A-16
1
" to length and width)
4
Infrared Warmer* - High intensity infrared elements
recessed in overhead enclosure 10" x 3" deep. Enclosure
supported at both ends by 1
1
" square tubular upright.
4
Furnished with pilot light and on/off switch. Infrared Warmer
compensates for surface heat loss.
2 Well 3 Well 4 Well
26" wide units
18" wide units
A-1
800 Watts
A-2
1100 Watts 1725Watts
A-2
1100 Watts 1400 Watts
A-3
A-3
Undershelf** - To be 18 gauge stainless steel with channel
reinforced longitudinal edges, located 7" above floor and
secured to pedestals at both ends.
2 Well 3 Well 4 Well
26" wide units
18" wide units
A-92
A-95
A-93
A-96
A-94
Overshelf - To be 16 gauge stainless steel, 10" wide with
channel edges. Supports to be 1" x
1
" flat bar. Shelf to be
4
located rear of unit 15" above work top.
2 Well 3 Well 4 Well
26" wide units
18" wide units
Sneeze Protector*** - To be
A-64
A-86
A-65
A-66
A-87
3
" clear polycarbonate plastic,
16
suspended from 16 gauge stainless steel overshelf.
2 Well 3 Well 4 Well
26" wide units
18" wide units
A-60
A-84
A-61
A-85
A-62
Infrared Warmer* - High intensity infrared elements
recessed in overhead enclosure 10" x 3" deep. Enclosure
supported at both ends by 1
1
" square tubular upright.
4
Furnished with pilot light and on/off switch. Infrared Warmer
compensates for surface heat loss.
3 Well
33" wide units
A-3
1725Watts
Extra Outlet**** - To be located on lower portion of end
panel opposite electric supply cord. Fused outlet to be 2
pole with ground prong.
A-6 - 10 Amp for 120 volts
A-7 - 6 Amp for 240 volts
Push Handle - To be 1" O,D. 16 gauge stainless steel
tubing with two 16 ga. stainless steel support brackets and
3" neoprene donut bumpers. Specify which end, when
facing control panel, at time of order.
33" wide units
A-13
ACC-52 - Vertical corner bumpers only. Easy to replace.
1
(Add 1
" to length and width)
4
ACC-22 - Removable stainless steel well liner for easy
draining and cleaning. One required for each well.
Extra Outlet**** - To be located on lower portion of end
panel opposite electric supply cord. Fused outlet to be 2
pole with ground prong.
A-6 - 10 Amp for 120 volts
A-7 - 6 Amp for 240 volts
All specifications subject to change without notice
* Not available with sneeze protector *** Includes overshelf.
** For open base models only. **** One outlet per unit only.
CADDY CORPORATION
509 Sharptown Road P.O. Box 345
Bridgeport, NJ 08014-0345
Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
08/08
Loading...