Caddy T-242 User Manual
CADDY CORPORATION
Air SystemsFood Service Equipment
Miscellaneous Caddys
6'-2"
PROJECT:
ITEM NO:
LOCATION:
General Specifications
Caddy to be Caddy Corporation model T-__________.
Top to be 18 gauge stainless steel turned down into 2" wide
channel edges, with corners welded. Top to be reinforced
with a 12 gauge stainless steel plate turned down 1" on each
side.
Legs to be 1
1
4
" 16 gauge stainless steel square tubing and
fitted with 5" diameter, heavy duty, double ball bearing,
swivel type casters with polyurethane tires. Two casters to
be provided with foot brakes.
Continue for:
T-242 Specifications:
Mixer Caddy to have one lower shelf of 16 gauge stainless
steel turned down into 2" channel edges, notched to fit
contour of legs, and continuously welded at all contact points.
One rear leg to extend through top to a height of 70",
enclosed at top, and fitted with five part rack pegs. Pegs to
be 6" long of
5
16
" stainless steel rod. First peg to be set 30"
above top of Caddy. Pegs to be spaced 3" apart and
staggered, with three facing front and two facing inward. All
pegs to be sloped upward 2". Part rack to be removable for
shipping.
Continue for:
T-243 Specifications:
Slicer Caddy to have three sets of 14 gauge stainless steel
channel slides spaced to accommodate 18" x 26" pans in
position to catch food directly from slicer.
page 1 of 1
All specifications subject to change without notice
Miscellaneous Caddys
Kitchen, Mixer, Slicer, Utensil
CADDY Food Service Systems
509 Sharptown Road P.O. Box 345
Bridgeport, NJ 08014-0345
Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
CADDY CORPORATION
08/08
T-243-A
Model
Length
Width
Height
26
1
4
" 30" 30"
Dimensions
T-243-B 26"26
1
4
" 30"
Continue for:
T-247 Specifications:
Utensil Caddy to have two lower shelves of 16 gauge
stainless steel turned down into 2" channel edges, notched to
fit contour of legs, and continuously welded at all contact
points. Shelves to be spaced 10" from top to bottom.
Utensil racks to be of 2" wide 10 gauge stainless steel bar
with stainless steel cross braces. Upper utensil rack to be
25
1
2
" diameter and lower utensil rack to be 13" diameter.
Racks to be fitted with 15 double-sided sliding utensil hooks,
10 on upper rack and 5 on lower rack. Both circular utensil
racks revolve, by hand, independently of each other. Utensil
racks supported by 1
5
8
" O.D. stainless steel tubing. Tubing to
pass through Caddy top and to be bolted to middle shelf.
Utensil rack to be removable for shipping.
Continue for:
T-247-P Specifications:
Utensil rack to be as specified as part of T-247 without caddy
or shelves. 1
5
8
" O.D. stainless steel tubing to be 74" long
with intermediate mounting flange and bottom mounting bolt.
Continue for:
T-249-A Specifications:
Kitchen Caddy to have two lower shelves of 16 gauge
stainless steel turned down into 2" channel edges, notched to
fit contour of legs, and continuously welded at all contact
points.
T-247 30" 30" 84"
T-242
Mixer Caddy
T-242 70"30" 24"
T-249-A 30" 30" 34
1
4
"
T-243-A
T-243-B
Slicer Caddy
T-249-A
Kitchen Caddy
T-247
Utensil Caddy
T-247-P
Utensil Rack
Loading...