Caddy T-130 User Manual
CADDY CORPORATION
Air SystemsFood Service Equipment
Transfer, Storage,
and Bussing Caddys
3'-9"
2'-10 1/2" 1'-7"
1'-10 1/2"
2'-11"
3'-9"
2'-10 1/2"
1'-10 1/2" 1'-10 1/2"
PROJECT:
ITEM NO:
LOCATION:
General Specifications
Tray & Silver Caddy to be Caddy Corporation model
T-_______________.
Frame to be of 1" O.D. 16 gauge stainless steel. Shelf to be
8" above the floor, of 18 gauge stainless steel with raised
rounded edges on all sides, flanged down to form a 1
1
2
"
wide channel. Shelf corners shaped to fit contour of tubular
frame and continuously welded to each leg at all contact
points which eliminates unsanitary crevices. Casters to be
4" diameter heavy-duty swivel type with
3
4
" stems and
polyurethane tires. Housing for cutlery receptacles to be of
18 gauge stainless steel with 16 gauge stainless steel end
enclosures and supports of all welded construction. Top of
cutlery housing provided with die-stamped reinforced
openings for standard perforated plastic cutlery cylinders.
T-402
Capacity:
10 Cutlery Cylinders
190 Trays up to 15" x 20"
Unit to be provided with the following accessories:
Accessories
page 1 of 1
All specifications subject to change without notice
ACC-36 - Removable stainless steel napkin dispenser
affixed to side of cutlery housing.
T-404
Capacity:
10 Cutlery Cylinders
120 Trays up to 15" x 20"
T-414
Capacity:
8 Cutlery Cylinders
195 Trays up to 15" x 20"
ACC-37 - Fold away auxiliary shelf to be 9
1
2
" wide, of 16
gauge stainless steel. Available on either or both sides.
ACC-38 - set of four circular leg bumpers.
(Add 4" to length and width)
ACC-41 - Caster brakes on two diagonal casters.
ACC-47* - Vinyl cover encloses entire caddy down to just
below under shelf.
* Specify for which model
** Specify quantity required
ACC-49** - Perforated plastic cutlery cylinders.
Approximate capacity per cylinder: 48 knives, 36 forks, or
40 spoons.
Tray & Silver Caddys for
Cafeteria Self-Service
with Cylinder-Type Silverware Dispensers
CADDY Food Service Systems
509 Sharptown Road P.O. Box 345
Bridgeport, NJ 08014-0345
Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
CADDY CORPORATION
08/08
3'-8"
2'-10 1/2"
1'-10 1/2"
4'-2 1/4"
2'-10 1/2"
1'-10 1/2"
2'-5"
1'-2 1/2"
10"
PROJECT:
ITEM NO:
LOCATION:
Mobile Unit
General Specifications
Tray & Silver Caddy to be Caddy Corporation model
T-_______________.
Frame to be of 1" O.D. 16 gauge stainless steel. Shelf to be
8" above the floor, of 18 gauge stainless steel with raised
rounded edges on all sides, flanged down to form a 1
1
2
"
wide channel. Shelf corners shaped to fit contour of tubular
frame and continuously welded to each leg at all contact
points which eliminates unsanitary crevices. Casters to be
4" diameter heavy-duty swivel type with
3
4
" stems and
polyurethane tires. Housing for cutlery receptacles to be of
18 gauge stainless steel with 16 gauge stainless steel end
enclosures and supports of all welded construction.
T-301
Capacity:
40 Dozen Cutlery Pieces
190 Trays up to 15" x 20"
page 1 of 1
All specifications subject to change without notice
T-303
Capacity:
80 Dozen Cutlery Pieces
190 Trays up to 15" x 20"
Tray & Silver Caddys
Mobile Units with Pan-Type Silverware Dispensers
and Counter Top Units
T-301 Specifications:
Cutlery housing fitted with
double folding covers of
fiberglass reinforced plastic
with 18 gauge stainless steel
hinges. Unit to be furnished
with four removable pans.
Pans to be seamless 304
type stainless with No. 4
finish. Each pan to measure
11
1
2
" x 6" x 4" deep.
T-303 Specifications:
Cutlery housing to have front
and back folding covers of
fiberglass reinforced plastic
with 18 gauge stainless steel
hinges. Unit to be furnished
with eight removable pans.
Pans to be seamless 304
type stainless with No. 4
finish. Each pan to measure
11
1
2
" x 6" x 4" deep.
T-320
Capacity:
40 Dozen Cutlery Pieces
T-400
Capacity:
10 Cutlery Cylinders
T-400
NOT SHOWN
T-400 Specifications:
Sloped top provided with ten
die-stamped reinforced
openings for standard
perforated plastic cutlery
cylinders.
T-320 Specifications:
Unit to be fit with double
folding covers of fiberglass
reinforced plastic with 18
gauge stainless steel hinges.
Unit to be furnished with four
removable pans. Pans to be
seamless 304 type stainless
with No. 4 finish. Each pan
to measure 11
1
2
" x 6" x 4"
deep.
Continue for Continue for
Unit to be provided with the
following accessories:
Accessories
ACC-49* - Perforated
plastic cutlery cylinders.
Approximate capacity per
cylinder: 48 knives, 36
forks, or 40 spoons.
T-400
NOT SHOWN
* Specify quantity required
Counter Top General Specifications
Counter Top Cutlery Dispenser to be Caddy Corporation model T-_______________.
Unit to be 20 gauge stainless steel with 16 gauge stainless steel end enclosures and
supports of all welded construction and set on non-slip rubber feet.
Continue for Continue for
CADDY Food Service Systems
509 Sharptown Road P.O. Box 345
Bridgeport, NJ 08014-0345
Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
CADDY CORPORATION
08/08
2'-8 1/2" 2'-10 1/2"
1'-10 1/2" 1'-10 1/2"
2'-6 3/4"
2'-10 3/4"
PROJECT:
ITEM NO:
LOCATION:
T-305
Capacity:
120 Dozen Cutlery Pieces
page 1 of 1
All specifications subject to change without notice
Bulk Silver Caddys
Pan-Type and Cylinder-Type
Continue for
T-305 Specifications:
Frame to be 1" O.D. 16 gauge stainless steel tubular
construction.
Casters to be 4" diameter heavy-duty swivel
type with
3
4
" stems and polyurethane tires.
Shelves to be of 12 gauge stainless steel entirely welded
seamless with cutouts. Shelf corners shaped to fit contour
of tubular frame and continuously welded to each leg at all
contact points which eliminates unsanitary crevices. Bottom
shelf to be 15" above the floor and upper shelf to be 28"
above the floor. Unit to be furnished with eight removable
pans. Pans to be seamless 304 type stainless with No. 4
finish. Each pan to measure 11
1
2
" x 6" x 6" deep.
Provide bulk
storage,
transportation and
dispensing in
cafeterias, dining
rooms, and
banquet rooms for
waiters or patron
self service.
General Specifications
Bulk Silver Caddy to be Caddy Corporation model T-_______________.
Unit to be provided with the following accessories:
Accessories
ACC-42 - Top and Bottom Shelf Covers to each be
provided with a double hinged fiberglass folding cover
with lock and key. Hinges to be 16 gauge stainless steel
and locks to be chrome plated brass.
ACC-38 - Circular bumpers. (Add 4" to length and width)
ACC-43 - Top Shelf Cover to be provided with a double
hinged fiberglass folding cover with lock and key. Hinge
to be 16 gauge stainless steel and lock to be chrome
plated brass.
ACC-41 - Caster brakes on two diagonal casters.
T-407
Capacity:
30 Cutlery Cylinders
Continue for
T-407 Specifications:
Frame to be of 1" O.D. 16 gauge stainless steel. Casters
to be 4" diameter heavy-duty swivel type with 3/4" stems
and polyurethane tires.
Shelves to be 16 gauge stainless steel with raised rounded
edges on all sides, flanged down to form a 1
1
2
" wide
channel. Bottom shelf to be 12
1
2
" from floor with 14
5
8
"
clearance between shelves. Shelf corners shaped to fit
contour of tubular frame and continuously welded to each
leg at all contact points which eliminates unsanitary
crevices. Each shelf to have 15 die-stamped reinforced
openings for standard perforated plastic cutlery cylinders.
Unit to be provided with the following accessories:
Accessories
ACC-49** - Perforated plastic cutlery cylinders.
Approximate capacity per cylinder: 48 knives, 36 forks, or
40 spoons.
ACC-38 - Circular bumpers. (Add 4" to length and width)
ACC-41 - Caster brakes on two diagonal casters.
ACC-47* - Vinyl Drape
ACC-47* - Vinyl Drape
* Specify model # T-305 or T-407
* Specify model # T-305 or T-407 ** Specify quantity required
CADDY Food Service Systems
509 Sharptown Road P.O. Box 345
Bridgeport, NJ 08014-0345
Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
CADDY CORPORATION
08/08
Loading...