Cadac Mighty 4 Stove, 400, 400F User guide

LIVE THE BRAAI LIFE

MIGHTY 4 STOVE

MODEL No: 400, 400F

2.8kPa

1002-148/2-RSA-17-A

USER INSTRUCTIONS

GB

NOTE! PRODUCT MAY VARY FROM ILLUSTRATIONS

503-0674 LEV6 (400, 400F) Mighty 4 Stove - User Manual (SA).indd 1 2021/02/23 08:34:12

503-0674 LEV6

503-0674 LEV6 (400, 400F) Mighty 4 Stove - User Manual (SA).indd 2 2021/02/23 08:34:13

Provide ample ventilation. This gas appliance consumes air (oxygen). Do not use this appliance in an unventilated space to

CAUTION

avoid endangering your life. If still more gas appliances and/or occupants using gas are added to the space, additional ventilation

must be provided.

GB

IMPORTANT

Read these instructions carefully so as to familiarise yourself with the appliance before ting the appliance to a gas cylinder.

Retain these instructions for future reference.

1. General

• This is an economic gas appliance designed for an optimal cooking experience using environment friendly LP gas.

• The appliance conforms to SANS 1539:2017 and SANS 1237:2012.

• Note that gures in this user manual are shown for visual purposes only and may differ to your appliance.

• Please read all the instructions and warnings on the appliance before use.

• It is important that all gas connections have been correctly connected to prevent any gas leaks.

• Do not use a leaking, damaged or malfunctioning appliance.

• This appliance requires an operating pressure of 2,8 kPa at the appliance. A suitable LPG regulator that complies with the requirements
of SANS 1237 must be installed.

• Ensure that the appliance is used in a well-ventilated area.

• Handle the appliance with care, do not drop it.

• When using a pot, the minimum recommended pot size is 150mm and maximum pot size is 300mm.

• The gas cylinder is to be used in an upright position only.

• Read the instructions before using the appliance.

• For outdoor use only!

2. Safety information

These instructions are for your safety and to help you avoid risk of injury and/or

damage. All warranties will become void if you do not follow these instructions.

• The hose and seal on the regulator must be checked for wear or damage before every
use and before connecting to the gas cylinder.

• In the event of light back (where the ame burns back and ignites at the jet)
immediately turn off the gas supply by rst closing the control valve on the gas cylinder
and then the appliance valve. After the ame is extinguished remove the regulator and
check the condition of its seal, replace the seal if in doubt. Re-light the appliance.
Should the ame persistently light back again return the product to your authorised
CADAC repair agent.

• Ensure the appliance is used away from ammable materials. Minimum safe distances;
above the appliance 1.2 m, at the rear and sides 600mm (Fig. 3).

• Do not use an appliance that is leaking, damaged or which does not operate properly.

• Ensure that the gas cylinder is tted or changed in a well-ventilated location,
preferably outdoors, away from any sources of ignition, such as naked ames and away
from other people.

• Keep gas cylinders away from heat and ame. Do not place on a stove or any other hot
surface.

• Ensure that the assembled product is stable and does not rock.

• Never leave the appliance unattended when lit.

• If there is a leak on your appliance (smell of gas), turn off the gas supply, rstly at
the gas cylinder and then on your appliance by turning the respective knobs fully
clockwise. Take them outside immediately into a well-ventilated ame-free location
where the leak may be detected and stopped.

• This appliance consumes oxygen and needs ventilation for optimum performance and
for safety of those in close proximity.

• Room ventilation is important for the efcient performance of the appliance and for the
safety of the occupants in the room.

• The room where this appliance is used should have a window or a door that can be
opened or partially open during use. If there is no window or door available for room
ventilation, extra ventilation must be installed for your sefety.

• If you wish to check for leaks on your appliance, do it outside. Do not try to detect
leaks using a ame, use soapy water. The correct way is to smear the joints with soapy
water. If bubbles form then there is a gas leak. Immediately turn off the gas supply
rst by closing the control valve on the gas cylinder and then the appliance valve,
check that all the connections are properly tted. Re-check with soapy water. If a gas
leak persists return the product to your CADAC dealer for inspection / repair.

• Do not modify the appliance. Do not use it for anything for which it has not been
designed.

• During use, parts of the appliance will become hot (particularly the burner) Avoid
touching hot parts with bare hands. The use of gloves is recommended.

• Keep young children away from the appliance at all times.

• Do not twist or pinch the hose.

• Do not move the appliance during use.

• Do not use the appliance without the Potstands being in place and properly located.

• Turn off the gas supply at the gas container after use.

• Do not modify the appliance, any modication may be dangerous.

11

Fig. 1

Fig. 1

Fig. 2

Fig. 3

503-0674 LEV6 (400, 400F) Mighty 4 Stove - User Manual (SA).indd 1 2021/02/23 08:34:19

Model: 400

Appliance catagories I

Allowable gasses Butane, Propane or their mixture

Gas pressure 2.8kPa

Ø110 burner jet no. 86

Ø110 burner nominal usuage

Ø110 burner gross nominal heat input

Ø75 burner jet no. 72

Ø75 burner nominal usuage

Ø75 burner gross nominal heat input

3. Assembly Instructions

PLEASE NOTE: Please ensure all protective packaging and plastic are
removed from the appliance before use.
This appliance may only be used with an approved hose and
regulator.
Connect the regulator to a CADAC 3kg, 5kg or 7kg LPG cylinder prior
to use (Fig. 1).
If you wish to use the appliance with a 9kg cylinder, please ensure
that you have purchased the correct hose and regulator suitable for a
9kg cylinder (Fig. 2).
The hose length should be no less than 600 mm and shall not
exceed 1.2 m and replace when the hose is damaged or shows signs
of brittleness or cracks.
Do not twist or pinch the hose. Ensure that it is routed away from
the Stove Body so as to prevent deterioration / damage to the hose
caused by heat.
Ensure that the appliance valves are in the off position by turning the
knobs fully clockwise to the stop.
Open the gas valve on the cylinder and test for any leaks.
Check all gas connections for any signs of gas leaks.
Your appliance is now ready to be used.

3B/P (30)

Butane - 240g/h per burner

(240g/h x 2 = 480g/h in total)

3.3kW per burner

(3.3kW x 2 = 6.6kW in total)

Butane - 168g/h per burner

(168g/h x 2 = 336g/h in total)

2.3kW per burner

(2.3kW x 2 = 4.6kW in total)

GB

Fig. 4

4. Fitting and Changing the Gas Cylinder

• Before connecting the appliance to a gas cylinder, ensure that the rubber seal on the
Regulator is in position and in good condition.

• Carry out this check each time you t the appliance to a gas cylinder.

• Blow out any dust from the cylinder opening to prevent possible blockage of the jet.

• Ensure that the appliance valves are in the off position by turning the knobs fully clockwise
to their stop.

• Ensure that the gas cylinder is tted or changed in a well-ventilated location, preferably
outdoors, away from any source of ignition, such as naked ames and away from other
people.

• Make sure that the gas cylinder is kept upright at all times, connect to the cylinder by
screwing on hand tight until fully engaged.

• Ensure that a complete gas seal has been made (check for the smell of gas around the
connection joint). If there is a leak on your appliance (smell of gas), take it outside
immediately into a well-ventilated ame free location where the leak may be detected and
stopped. To check for leaks on your appliance, do it outside using warm soapy water only,
which is applied to the joints and connections of the appliance. A formation of bubbles will
indicate the gas leak. Do not check for leaks with a naked ame.

• If you cannot rectify the gas leak do not use the appliance, contact your local CADAC
stockist for assistance.

• CADAC gas cylinder valves must only be repaired by an authorised CADAC service centre or
dealer.

• When changing a gas cylinder rstly close the appliance control knobs and then the cylinder valve, making sure the ame is
extinguished, unscrew the regulator. Re-t the regulator to a full cylinder following the same precautions as described above.

22

503-0674 LEV6 (400, 400F) Mighty 4 Stove - User Manual (SA).indd 2 2021/02/23 08:34:24

Fig. 5

5. Operating the Appliance

The appliance is designed for use with cooking vessels of not less than 180mm in diameter and not greater than 250mm in
diameter.
After lighting, do not move the gas cylinder and the appliance around, as liqueed gas may enter the appliance from the gas
cylinder, causing it to are (large yellow ames).
Always operate the appliance on a rm level surface with the gas cylinder in an upright position.

Lighting the Appliance using the piezo:

• Turn the control knob clockwise to the ‘OFF’ position.

• Turn the gas supply ‘ON’ at the cylinder.

• Push down the control knob and keep pressing whilst turning anti-clockwise to the ‘Ignition’ position. This should light the burner.

Repeat this several times until the burner lights. If not, wait at least 3 minutes and repeat this process.

• When the burner is lit, keep the control knob pressed for a few seconds, then release it.

• If the burner does not stay alight, repeat steps 3 and 4. Adjust the heat by turning the knob to the ‘High/Low’ position.

• To turn the stove ‘OFF’, turn the cylinder valve to the ‘OFF’ position and then turn the control knob on the appliance clockwise to the

‘OFF’ position.

• Always close the cylinder valve after usuage. This will prolong the life of the regulator and prevent any gas leakages if the appliance is

not in use.

Warning: If the burner fails to ignite within 10 seconds, turn the control knob off (clockwise). Wait three minutes before attempting to
re-light with ignition sequence.

Lighting the Appliance with a match:

• To light the appliance, light a match or barbecue lighter, turn on the appliance valve after connecting to and opening the cylinder

valve, by turning the control knob (E) in an anti-clockwise direction. Light the appliance burners.

• Use the control knob to adjust the ame intensity to the desired level by turning the knob clockwise to decrease the ame and

anti-clockwise to increase it.

• Always light the match or the lighter rst before opening the gas valve on the appliance.

Fig. 6

GB

6. General Maintenance

This appliance does not require scheduled maintenance.

• It is dangerous to use an appliance with a cracked or perished seal and / or hose. Inspect both seals and hose regularly and replace if
they are not in order, before using the appliance.

• If the appliance was in use, it will be hot. Allow to cool sufciently before attempting any maintenance.

• The stoves are tted with jets to regulate the correct amount of gas.

• Should the hole in the jet become blocked this may result in a small ame or no ame at all.

• Do not attempt to clean the jet with a pin or other such device as this may damage the orice, which could make the appliance
unsafe.

Replacing a blocked jet:

• Ensure that the cylinder valve is closed, then disconnect the appliance from the gas cylinder.

• Remove the pot stand/cooking surfaces from the stove body (A).

• Turning the appliance upside down, unscrew the screws holding the bracket of the burner to the body (B).

• From the top now, you can safely remove the burners from the appliance.

• Unscrew the blocked jet from the valve with a suitable spanner and replace it with a new jet (C).

• Do not over tighten as this may damage the Jet. To re-assemble, reverse the above procedure.

• Do not use pliers on the jet as this may damage the jet making it unusable or impossible to remove.

33

503-0674 LEV6 (400, 400F) Mighty 4 Stove - User Manual (SA).indd 3 2021/02/23 08:34:27

GB

A

B

C

7. Troubleshooting

• A normal ame is blue and may have a yellow tip. If the ame is completely yellow, it may be that the jet is not securely tted. Re­tighten the jet to give a gas tight seal. An overlled gas cylinder can also cause large yellow ames. Cylinder should be returned to
lling station and checked by weight.

• Check that the inlet to the burner pipe is clear and free of obstructions.

• If the ame power drops or the gas will not light, check that the gas cylinder still contains gas (shake to hear the noise made by the
liqueed gas). If there is still gas, the jet might have become blocked or partially blocked.

• If you suspect a blocked jet, follow the instructions above.

• Check for spider webs or insect nests in the gas tube or primary air inlet.

8. Cleaning

• It is recommended to clean your appliance after every use. This will prolong the life of your appliance.

• The pot stand is removed by lifting it from the stove top and can be washed in a detergent solution.

• To clean the stove body, simply wipe with a damp cloth using a little detergent, if necessary.

• DO NOT IMMERSE IN WATER as this will allow water to get into the burner tube causing the appliance to malfunction.

• Do not use abrasive cleaners or scourers as this will cause permanent damage to the surface.

• To avoid ignition failure, keep the burners clean.

• Use a brush to clean the burners.

• A tooth brush may be used to clean out the venturi should there be any obstacles within the venturi.

9. Storage

• Handle the appliance with care. Do not drop it.

• After use, wait until the appliance has cooled down, disconnect it from the gas cylinder and store them in a cool dry place. Store your
cylinder in a well-ventilated place.

• It helps to place the appliance in a plastic bag when not in use as this will prevent the ingress of dirt and insects, which may affect
the gas ow.

• Warning: An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.

• LPG cylinders should preferrably be stored outdoors if not in use.

44

503-0674 LEV6 (400, 400F) Mighty 4 Stove - User Manual (SA).indd 4 2021/02/23 08:34:31

10. Spares

• Always use genuine CADAC spares as they have been designed to give optimum performance.

11. Returning the Appliance for Repair or Service

• Do not modify the appliance. Any modication of the appliance may be dangerous.

• Any modications will render the CADAC warranty null and void.

• If you cannot rectify any fault by following these instructions, contact your local CADAC distributor for inspection/repair

GB

55

503-0674 LEV6 (400, 400F) Mighty 4 Stove - User Manual (SA).indd 5 2021/02/23 08:34:35

12. Warranty

CADAC (Pty) Ltd hereby warrants to the ORIGINAL PURCHASER of this CADAC gas appliance for 2 years, that it will be free of defects

in material and workmanship from the date of purchase as follows:

Valves: 2 Years
Plastic parts: No Warranty
Enamel parts: 2 Years
Cast Iron: 2 Years
Burners: 1 Year

The warranty will only apply if the unit is assembled and operated in accordance with the printed instructions.

CADAC may require reasonable proof of your date of purchase. THEREFORE, YOU SHOULD RETAIN YOUR SALES SLIP OR INVOICE.

This Limited Warranty shall be limited to the repair or replacement of parts that prove defective under normal use and service and

which on examination shall indicate, to CADAC’s satisfaction, they are defective. Before returning any parts, contact the customer
service representative in your region using the contact information provided with your manual or call 0860 223 220 (RSA only). If
CADAC conrms the defect and approves the claim, CADAC will elect to replace such parts without charge. CADAC will return parts to
the purchaser, freight or postage prepaid.

This Limited Warranty does not cover any failures or operating difculties due to accident, abuse, misuse, alteration, misapplication,

vandalism, improper installation or improper maintenance or service, or failure to perform normal and routine maintenance, including
but not limited to damage caused by insects within the burner tubes, as set out in this owner’s manual.

Deterioration or damage due to severe weather conditions such as hail, hurricanes, earthquakes or tornadoes, discoloration due to

exposure to chemicals either directly or in the atmosphere, is not cover by this Limited Warranty.

There are no other express warrants except as set forth herein and any applicable implied warranties of merchantability and tness are

limited in duration to the period of coverage of this express written Limited Warranty. Some regions do not allow limitation on how
long an implied warranty lasts, so this limitation may not apply to you.

CADAC is not liable for any special, indirect or consequential damages. Some regions do not allow the exclusion or limitation of

incidental or consequential damages, to this limitation or exclusion may not apply to you.

CADAC does not authorize any person or company to assume for it any obligation or liability in connection with the sale, installation,

use, removal, return, or replacement of its equipment; and no such representations are binding on CADAC.

This Warranty applies only to products sold at retail.

To enjoy and ensure longevity of your CADAC product, please refer to the cleaning and maintenance section of the user manual with

particular attention to the care of the Stainless Steel.

GB

66

503-0674 LEV6 (400, 400F) Mighty 4 Stove - User Manual (SA).indd 6 2021/02/23 08:34:35

77

503-0674 LEV6 (400, 400F) Mighty 4 Stove - User Manual (SA).indd 7 2021/02/23 08:34:35

LIVE THE BRAAI LIFE

CADAC INTERNATIONAL

P.O. Box 43196,
Industria, 2042 South Africa
Tel: [phone]
Email: [e-mail]
www.cadacinternational.com

CADAC UK

14 Deaneld Court,
Link59 Business Park,
Clitheroe, Lancashire,
BB7 1QS
United Kingdom.
Tel: [phone]
E:mail: [e-mail]
www.cadacinternational.com

CADAC MOZAMBIQUE

Exclusive Brands Africa
492 Avenida Namaacha
Maputo, Mozambique
Tel: [phone]
www.cadac.co.mz

CADAC IRAN

Robin Bazarganan Carin Co.
Unit D, 6th Floor, Negin Zafar
Building, No.1327,
Shariati Street, Tehran, Iran
Tel: [phone]
Mail: [e-mail]

CADAC CHINA

Room 807, Huayue International
Building, No.255 Tiangao Road,
South
Yinzhou business district,
Ningbo, China
Tel:[phone]
Email: [e-mail]

CADAC SWEDEN & NORWAY

KAMA FRITID AB
0046 36 353700
[e-mail]

CADAC EUROPE

Ratio 26, 6921 RW Duiven
The Netherlands
Tel: [phone]
Email: [e-mail]
www.cadacinternational.com

CADAC SCANDINAVIA

Millarco International A/S
Rokhøj 26
8520 Lystrup, Denmark
Phone: [phone]
[e-mail]
www.millarco.com

CADAC MONTENEGRO

City kvart Z1L6
81000 Podgorica, Montenegro
Tel [phone],
38269020063
E-mail: [e-mail]

CADAC DENMARK

Camper Fritid
Industrivej 11
6640 Lunderskov, Denmark
Tel.: [phone]
Email: [e-mail]
www.camper.dk

CADAC ZIMBABWE

Exclusive Brands Africa
Unit 8 Birkenhead Park
43 Josiah Chinamano Street
Belmont, Bulawayo
Tel: [phone] (Bul)
Tel: [phone] (Har)
www.cadac.co.zw

CADAC GERMANY

Ratio 26, 6921 RW Duiven
The Netherlands
Tel: [phone]
Email: [e-mail]
www.cadacinternational.com

CADAC Czech Rep.

RÖSLER Praha spol. s r.o.
K Horkám 19/21

102 00 Praha 10 Česká republika
Tel: [phone]
Email: [e-mail]
www.rosler.cz

CADAC FINLAND

OY KAMA FRITID AB
Koivuhaantie 2-4 B
01510 VANTAA
00358 20 792 0310
info@kamafritid.

CADAC POLAND

Kamai
Wola Batorska 461
32-007 Wola Batorska Poland
Tel: [phone]
Email: [e-mail]
www.kamai.pl

CADAC ZAMBIA

Exclusive Brands Africa Limited
7225A Kachidza Road
Light Industrial Area
Lusaka, Zambia
Tel: [phone]
Tel: [phone]
Email: [e-mail]

CADAC FRANCE

Le Viallon, 42520 Veranne
France
Tel: [phone]
Email : [e-mail]
www.cadacinternational.com

CADAC NEW ZEALAND

Riverlea Group (Pty) Ltd
2A Maui Street, Pukete,
Hamilton 3200, New Zealand
Tel: [phone]
Email: [e-mail]
www.riverleagroup.co.nz

CADAC U.A.E.

Supreme Impex General Trading
LLC Ofce No. 1801-7 Latifa
Tower Sheikh Zayed Road
Dubai, UAE

CADAC ITALY

Brunner SRL/GMBH
via Buozzi, 8
39100 Bolzano (Italy)
Tel: [phone]
Email: [e-mail]
www.brunnerinternational.com

CADAC SOUTH EAST EUROPE

Bulevar oslobodjenja 285
Tel: [phone]
Email: [e-mail]
www.cadac.rs

88

503-0674 LEV6 (400, 400F) Mighty 4 Stove - User Manual (SA).indd 8 2021/02/23 08:34:35