USER INSTRUCTIONSUSER INSTRUCTIONS
Cook 200
Cook n Grill 200
MODEL No 5900
MODEL No 5910
503-0182 LEV2
Cook 200
MODEL No 5900
Grill 200
MODEL No 5910
LIVE THE BRAAI LIFE
0063
PIN: 0558CM1289
?
?
?
?
?
?
?
?
?
This appliance is designed tocomply with BSEN 521:2006and SANS1539: 2006
Appliance category: Vapour pressure - Propane/Butane mix
This appliance shall only be used with the CADAC 500g disposable threaded resealable gas
cartridge (Model CA500) complying with EN417.
It may be hazardous to attempt to fit other types of gas cartridges.
Nominal Usage: 167g/hour
Gross Nominal Heat Input: 2.34kW
This product uses a CADAC 0.25 Jet
Gas appliances require ventilation for efficient performance and to ensure the safety of users and other
persons in close proximity.
Use Outdoors only!
1. General
2. Safety Information
?
?
?
?
?
?
?
?
Check that the seal is in place and in good condition before connecting the gas cartridge to the
appliance (see fig. 1).
Do not use an appliance that is leaking, damaged or which does not operate properly (malfunctioning).
Always operate the appliance on a level surface.
Always operate the appliance safely away from flammable materials. Minimum distances are
120cm above the appliance and 60cm to the rear and sides (see fig. 2).
Ensure that the gas cartridge is fitted or changed in a well-ventilated location, preferably outdoors,
away from any sources of ignition, such as naked flames, and away from other people.
If suspect a leak on your appliance (smell of gas), take it outside immediately into a well-ventilated
flame free location where the leak may be detected and stopped. If you wish to check for leaks on
your appliance, do it outside.
Never leave the appliance unattended when lit.
Do not modify the appliance. Do not use it for anything for which it has not been designed.
Do not use the appliance if it has a damaged or worn seal.
Do not try to detect leaks using a flame, the correct way
is to use soapy water.
CAUTION
IMPORTANT
Provide ample ventilation. This gas appliance consumes air (oxygen). Do not use this appliance in an unventilated space to avoid
endangering your life. If still more gas appliances and/or occupants using gas are added to the space, additional ventilation must
be provided.
Read these instructions carefully so as to familiarise yourself with the appliance before use.
Retain these instructions for future reference.
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
Before each use, ensure that the fat pan is clean and free of fat .
Keep young children away from the appliance at all times.
Handle the appliance with care, do not drop it.
During use, parts of the appliance will become hot (particularly the burner). Avoid touching hot parts
with your bare hands. If you have the need to touch a hot appliance, use gloves.
Before fitting the cartridge to the appliance, ensure that the valve seal is place and in good condition.
Carry out this check each time you fit a cartridge.
(Model 5910 Only)
?
Ensure that the control knob is turned off (turned fully clockwise) (see fig. 3).
Keep the cartridge upright when fitting it to the appliance. Carefully screw the cartridge into the
appliance, taking care not to screw the cartridge cross-threaded. Screw the cartridge on hand tight
only. Do not over tighten as you may damage the cartridge and appliance threads.
Check that the cartridge is connected to the appliance in a gas tight fashion, showing no signs of
leakage (check for the smell of gas around the connection joint). If you suspect that the connection in
not gas tight enough, soapy water must be applied to the joint (the appliance must not be fully
immersed in soapy water as this may result in an unsafe operation of the appliance). Any leak will be
seen as bubbles coming from the leakage point.
If you cannot remedy any leakage, unscrew the cartridge from the appliance and return the appliance
to your nearest CADAC stockist.
If you suspect a leakage from your appliance during use, immediately turn off the appliance control
knob (turned fully clockwise), take the appliance outside and follow the instructions above.
To light the appliance, hold a flame to the burner, turn the control knob slowly anti-clockwise and light
the burner (see fig. 4).
After lighting, do not move the appliance around during the warm up period (1 minute), as liquid gas
may enter the appliance from the cartridge causing it to flare (large yellow flames).
If flaring occurs, turn down the control knob until the flaring stops.
When in use, protect from wind for optimum performance.
Adjust the size of the flame by turning the control knob. To increase the size of the flame, turn the
control knob in the direction of the ‘+’ (anti-clockwise). To decrease the size of the flame or to turn the
appliance off, turn the knob in the direction of the ‘-’ (clockwise) (see fig. 3).
After use, always ensure the control knob is turned fully off and the appliance has cooled down
sufficiently to be able to be packed away.
In the event of light back, where the flame burns back and ignites inside the burner or venturi housing,
immediately turn the appliance off by turning the control knob fully clockwise. After the flame is
extinguished, remove the gas cartridge and check the condition of the seal; replace the seal if in doubt.
Re-light the appliance as described above. Should the flame persistently light back, return
the product to your authorised CADAC repair agent.
Flaring may also occur if food with a
high fat content is cooked with the heat setting too high. In this instance, reduce the heat setting by
adjusting the control knob.
3. Using The Appliance
Seal
Fig. 1
Fig. 2
60cm
120cm
60cm
60cm
60cm
Flammable
Fig. 3
Fig. 4
GB
5. Cooking On The Appliance
?
?
Boiling: Place the cooking vessel (pot, pan or kettle) centrally onto the pot stand. Pot sizes that may be used vary between minimum 150mm and
300mm maximum in diameter. Be carefull not to turn the heat up too much when using pots with plastic handles as they may be damaged by heat
escaping from underneath the pot. Depending on the conditions and the pot size used, one liter of water will boil in approximately 6 minutes.
Grilling and Frying : The non-stick coated aluminium grill plate heats up quickly and evenly, searing meats and locking in their
natural juices and flavours.
(Model 5910 only!)
6. Caring For The Grill Plate
?
?
?
?
?
?
?
When using the grill plate for the first time, lightly coat the cooking side of the grill plate with oil before heating.
Pre-heat the grill plate before cooking and use only low or medium heat settings. Don not over heat the grill plate.
Whilst the non-stick coating is very durable, it is recommended to use only plastic or wooden utensils when cooking as metal utensils will tend to
damage the coating.
Always let the grill plate cool down before immersing it in water.
The non-stick coating is perfectly safe in the dishwasher, but its surface is so easy to clean that a quick handwash does the trick. The use of
abrasive detergents is not recommended, as this will permanently damage the non-stick surface.
If burned grease or food residue collects on the surface, it can usually be removed with warm water and a mild detergent. In an extreme case, it
can be removed by a thorough cleaning with a mixture of 3 tablespoons of bleach, 1 tablespoon of liquid detergent and 1 cup of water. Apply to the
cooking surface with a sponge or plastic scrubbing pad.
After cleaning recondition the surface with a light wipe of oil.
7. General Maintenance
?
?
?
?
?
?
?
To remove the seal from its location groove, use a pointed instrument to lift it out of the groove. Take care not to damage the surface of the location
groove.
To fit a replacement seal, squeeze the seal to an oval shape, push one end into the location groove, then gently push in the rest of the seal until it
is fully fitted into the location groove.
If the flame power drops or the burner will not light, check that the gas cartridge still contains gas (shake to hear the noise made by the liquid). If
the cartridge still contains gas, the jet may be blocked.
The Jet is now exposed for removal.
Unscrew the jet using a suitable size spanner. Do not use pliers as this may damage the jet, making it unusable or impossible to remove. Do not
attempt to clean the old jet, rather fit a new jet. Do not over tighten the jet (see fig. 5a-c).
To re-assemble the appliance, gently screw the burner assembly back into position in a clockwise direction.
Replacing a blocked jet
Gently unscrew the burner assembly, by turning it in an anti-clockwise direction.
?
?
?
?
?
?
Always read the gas cartridgemarkings.
Always change the gas cartridgeoutside and away fromother people.
Check that the flame isextinguished before disconnecting thecartridge fromthe appliance.
To disconnect the cartridgefrom theappliance, unscrew the cartridgein an anti-clockwise direction.
Check the seal before connecting a cartridge to the appliance. It should be in place in its location groove and be in good condition. Do not connect a
cartridge to the appliance ifthe seal is wornor damaged.If in doubt,replace theseal before use.
When fitting a gas cartridgeto the appliance, followthe instructionsin Section 3.
4. Fitting and changing the gas cylinder
Fig. 5a Fig. 5b Fig. 5c
Jet
8. Cleaning
? The appliance is best cleaned by using a soft damp cloth and a mild non-abrasive detergent. Do not place in a dishwasher as this may allow water
into the valve or burner ports which will cause the unit to malfunction.
The fat pan is perfectly safe to clean in the dish washer after removing any excess fat. Cleaning and caring for the grill plate is described in Section
6 above
?
(for Model 5910 only!)
9. Storage
When not in use, wait until the appliance has cooled down and then unscrew the gas cartridge. Store the appliance in the supplied carry bag, as
this will prevent the ingress of dirt or insect that may affect the gas blow.
Store the appliance in a cool dry place, preferably off the ground.
Always ensure that the appliance has cooled down fully before packing it away in its bag.
10. Spares and Accessories
Always use genuine CADAC spares as they have been designed to give optimum performance.
5910-2
SPARES
Non-stick reversible grill plate
(Model 5910 only)
11. Returning The Appliance For Repair Or Service
Do not modify the appliance. This may cause the appliance to become unsafe.
If you cannot rectify a fault by following these instructions, contact your local CADAC distributor for details on how to return the product for repair
Jet No. 0.25
6528
12. Assembly Instructions
Cook 200 (Model 5900)
Step 1 Step 2 Step 3a
Step 3b Step 4a Step 4b
12. Assembly Instructions
Step 1 Step 2
Step 4a
Cook n Grill 200 (Model 5910)
Step 4b
Step 5
Step 3b
Step 3a
Step 6
Loading...