Cabletron Systems E2210, E2211, E2212, E2214, E2219 Installation Manual

E2200 SERIES

FULL-DUPLEX ETHERNET

NETWORK ADAPTERS

INSTALLATION GUIDE

Installation Procedure

Quick Start

Quick Start

If you are an
computer, its operating system, and the installation of network
adapters - you can follow this simple installation procedure, and
use the subsequent chapters in this manual for reference if
necessary.

!

CAUTION

Plug and Play Systems

“Plug and Play™” is an automatic configuration scheme. Your
computer can be considered a “Plug and Play” system if it uses
either a Plug and Play BIOS, or a Plug and Play operating system,
or a Plug and Play Configuration Manager device driver. Plug and
Play software will automatically set the parameters of IRQ, I/O
Base Address, and DMA channel for all adapters that are plugged
into the system at power up time.

experienced user

The E2200 network adapters are sensitive to static
discharges. Touch the metal chassis of your computer to
discharge any static electricity. Hold the adapter by the top
of the metal bracket and the opposite top corner. Avoid
contact with the adapter’s expansion bus edge connector or
any of the adapter’s components. Failure to observe all static
precautions could result in damage to the adapter. We
recommend the use of an antistatic wrist strap.

, and you are familiar with your

WARNING

Make sure power to your PC is switched off and
the power cord unplugged before you open the
chassis. Opening the PC chassis with power on
can subject you to a serious electrical hazard.

At this time, if you need to install a Boot ROM, see

Installing a Boot ROM

next page.

Section 2.3.1,

. Otherwise follow the steps outlined on the

Page - 1

Quick Start

To install the E2200 network adapter follow these guidelines:

1.) Turn off your computer and unplug the power cord and
peripheral equipment cables.

2.) Remove the computer cover and locate an expansion
slot. Remove the expansion slot cover.

3.) Carefully insert the adapter in the expansion slot until it
is fully seated. Secure the adapter bracket with the
expansion slot cover screw.

4.) Replace the computer cover. Connect a 10BASE-T
network cable to the adapter’s RJ45 port.

Reconnect all cables and, if you are using Windows95™, power up
your computer and follow screen instructions. The operating
system will find your E2200 adapter and load the necessary
network driver (from within Windows95). Your adapter will be
ready to use. See additional steps below for other operating system
installation.

5.) If your operating system finds a configuration
parameter conflict, see Section 2.6.1,

Configuration Utility

, for information on how to

The QuickSet

change configuration parameters.

6.) When the system is operational, insert the Cabletron
Software floppy disk into the floppy drive.

7.) In the README directory on the software disk, locate
the README file for the network driver you need, and
proceed with network driver installation as outlined in
the README file.

8.) Reboot the computer and check that the Link LED and
the Network Activity LED are lit.

Your computer is now ready to communicate on the
network.

Page - 2

NOTICE

NOTICE

Cabletron Systems reserves the right to make changes in
specifications and other information contained in this document
without prior notice. The reader should in all cases consult
Cabletron Systems to determine whether any such changes have
been made. The hardware, firmware, or software described in this
manual is subject to change without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR
ANY INCIDENTAL, INDIRECT, SPECIAL, OR
CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING
BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR
RELATED TO THIS MANUAL OR THE INFORMATION
CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN
ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE
POSSIBILITY OF SUCH DAMAGES.

VIRUS DISCLAIMER

Cabletron has tested its software with current virus checking
technologies. However, because no antivirus system is 100%
reliable, we strongly caution you to write protect and then verify
that the Licensed Software, prior to installing it, is virus-free with
an anti-virus system in which you have confidence. Cabletron
Systems makes no representations or warranties to the effect that
the Licensed Software is virus-free.

© Copyright September 1995, Cabletron Systems, Inc.
35 Industrial Way, P.O. Box 5005, Rochester, NH 03867-0505

All Rights Reserved, Printed in the United States of America
Order Number: 9030978-01 Sept 95

SPECTRUM

Cabletron Systems, Inc. All other trademarks are for reference only,
and are the property of their respective owners.

and

Remote LANVIEW

are registered trademarks of

Printed on recycled paper.

i

NOTICE

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.

NOTE:

This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment uses,
generates, and can radiate radio frequency energy and if not
installed in accordance with the operator’s manual, may cause
harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause interference in
which case the user will be required to correct the interference at
his own expense.

WARNING:

Changes or modifications made to this device which
are not expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.

This digital apparatus does not exceed the Class A limits for radio
noise emissions from digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of
Communications.

Le présent appareil numérique n’émet pas de bruits
radioélectriques dépassant les limites applicables aux appareils
numériques de la class A prescrites dans le Règlement sur le
brouillage radioélectrique édicté par le ministère des
Communications du Canada.

ii

DOC NOTICE

PROGRAM LICENSE AGREEMENT

CABLETRON SYSTEMS, INC.

PROGRAM LICENSE AGREEMENT

IMPORTANT:

Agreement.

This document is an agreement between you, the end user, and Cabletron
Systems, Inc. (“Cabletron”) that sets forth your rights and obligations
with respect to the Cabletron software program (“the Program”)
contained in this package. The Program may be contained in firmware,
chips, or other media. BY UTILIZING THE ENCLOSED PRODUCT, YOU
ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS
AGREEMENT, WHICH INCLUDES THE LICENSE AND THE
LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF
YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT,
PROMPTLY RETURN THE UNUSED PRODUCT TO THE PLACE OF
PURCHASE FOR A FULL REFUND.

1. LICENSE. You have the right to use only the one (1) copy of the
Program provided in this package subject to the terms and conditions
of this License Agreement.

Before utilizing this product, carefully read this License

CABLETRON SOFTWARE PROGRAM LICENSE

You may not copy, reproduce or transmit any part of the Program
except as permitted by the Copyright Act of the United States or as
authorized in writing by Cabletron.

2. OTHER RESTRICTIONS. You may not reverse engineer, decompile,
or disassemble the Program.

3. APPLICABLE LAW. This License Agreement shall be interpreted
and governed under the laws and in the state and federal courts of
New Hampshire. You accept the personal jurisdiction and venue of
the New Hampshire courts.

EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY

1. EXCLUSION OF WARRANTY. Except as may be specifically
provided by Cabletron in writing, Cabletron makes no warranty,
expressed or implied, concerning the Program (including Its
documentation and media).

iii

PROGRAM LICENSE AGREEMENT

CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN
THOSE SUPPLIED TO YOU BY CABLETRON IN WRITING, EITHER
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE
PROGRAM, THE ACCOMPANYING WRITTEN MATERIALS, AND
ANY ACCOMPANYING HARDWARE.

2. NO LIABILITY

FOR CONSEQUENTIAL DAMAGES. IN NO
EVENT SHALL CABLETRON OR ITS SUPPLIERS BE LIABLE FOR
ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT
LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS,
BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION,
SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE
DAMAGES, OR OTHER LOSS) ARISING OUT OF THE USE OR
INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF
CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF LIABILITY FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR IN THE
DURATION OR LIMITATION OF IMPLIED WARRANTIES IN
SOME INSTANCES, THE ABOVE LIMITATIONS AND
EXCLUSIONS MAY NOT APPLY TO YOU.

UNITED STATES GOVERNMENT RESTRICTED RIGHTS

The enclosed product (a) was developed solely at private expense; (b)
contains “restricted computer software” submitted with restricted rights
in accordance with section 52227-19 (a) through (d) of the Commercial
Computer Software - Restricted Rights Clause and its successors, and (c)
in all respects is proprietary data belonging to Cabletron and/or its
suppliers.

For Department of Defense units, the product is licensed with “Restricted
Rights” as defined in the DoD Supplement to the Federal Acquisition
Regulations, Section 52.227-7013 (c) (1) (ii) and its successors, and use,
duplication, disclosure by the Government is subject to restrictions as set
forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and
Computer Software clause at 252.227-7013. Cabletron Systems, Inc.,
35 Industrial Way, Rochester, New Hampshire 03867.

iv

CONTENTS

CONTENTS

Quick Start

Plug and Play.................................................................................1

Warning ..........................................................................................1

CHAPTER 1 Introduction

1.1 Using this Manual.....................................................................1–1

1.2 Getting Help ..............................................................................1–2

1.3 E2200 Series Adapter Features................................................1–3

1.3.1 Connectivity .................................................................1–3

1.3.2 Software.........................................................................1–4

1.3.3 Statistics.........................................................................1–5

1.3.4 LANVIEW® LEDs.......................................................1–5

1.4 FDSE Technology Overview ...................................................1–6

1.4.1 Why Full-Duplex Switched Ethernet?......................1–6

1.4.2 MAC Layer ...................................................................1–7

1.4.3 MAU Operation ...........................................................1–7

1.4.4 FDSE Cabling ...............................................................1–8

CHAPTER 2 Installation

2.1 Installation Requirements........................................................2–1

2.1.1 Plug and Play Compatibility......................................2–1

2.1.2 Unpacking the Adapters.............................................2–2

2.2 Preparing the Adapters............................................................2–2

2.3 Installing the Adapters.............................................................2–3

2.3.1 Installing a Boot ROM.................................................2–3

2.3.2 Boot ROM and Socket Alignment .............................2–4

2.3.3 Installation Procedure.................................................2–4

2.4 Connecting Primary Media .....................................................2–6

2.4.1 RJ45 Interface................................................................2–6

2.5 LANVIEW LEDS.......................................................................2–7

2.5.1 Using LANVIEW LEDs ..............................................2–8

2.6 Loading Network Software.....................................................2–9

2.6.1 The QuickSet™ Configuration Utility ....................2–10

2.6.2 Plug and Play System Configuration......................2–11

2.6.3 Non Plug and Play System Configuration.............2–12

v

CONTENTS

CHAPTER 3 Secondary Media

3.1 Connecting to a Thin-Net Segment........................................ 3–1

3.2 Connecting to an External Transceiver.................................. 3–3

3.2.1 AUI Port........................................................................3–3

3.2.2 AUI Interface................................................................3–4

3.3 Connecting to a Fiber Optic Link........................................... 3–4

APPENDIX A Technical Specifications

A.1 E2200 Series Specifications..................................................... A–1

A.1.1 RJ-45 Pinouts...............................................................A–2

A.1.2 Twisted Pair Requirements.......................................A–2

A.1.3 Thin-Net Requirements .............................................A–4

A.1.4 AUI Cable Requirements ..........................................A–4

A.1.5 Fiber Optic Requirements .........................................A–5

INDEX

vi

CHAPTER 1

INTRODUCTION

INTRODUCTION

The Cabletron Systems

Network Adapters Installation Guide

E2200 Series Full-Duplex Ethernet

is a simple installation and
reference guide for the Cabletron Systems E2200 Series of Full­Duplex Ethernet network adapters. The E2200 Series network
adapters connect your ISA Bus, or EISA Bus compatible computer
to an Ethernet network utilizing 10BASE-T twisted pair, and
possibly one of; 10BASE-2 Coaxial cable, Fiber Optic, or
10BASE-5 transceiver technologies. You should read through this
manual to gain a full understanding of the capabilities of the
Cabletron Systems E2200 Series Full-Duplex Ethernet adapters.

1.1 USING THIS MANUAL

This manual is structured so that you can follow sequential
chapters as you install and test the Cabletron E2200 series network
adapters. A

Quick Start

procedure is included for experienced
users; a short cut installation procedure for those who are familiar
with networks, PCs, and Ethernet technology.

Chapter 1,
Systems E2200 Series network adapters. An

Overview

Introduction

, discusses the capabilities of the Cabletron

FDSE Technology

describes the Full-Duplex Switched Ethernet (FDSE)

technology supported by the E2200 series network adapters.

Chapter 2,

Installing the Adapters

, contains instructions for
installing the E2200 series adapters in ISA Bus or EISA Bus
compatible computers.

Chapter 3,

Secondary Media

, provides instructions for connecting
the network adapters to secondary Ethernet media such as Thin­Net coax, AUI transceiver, or fiber optics.

Appendix A,

Technical Specifications

, provides specifications for

the E2200 Series adapters and the FDSE network technology.

Page 1 - 1

INTRODUCTION

1.2 GETTING HELP

If you need additional support related to the network adapters, or
if you have any questions, comments, or suggestions concerning
this manual, contact Cabletron Systems Technical Support. Before
calling Cabletron Technical Support, please have the following
information available for use by the Cabletron Technical Support
personnel who will assist you.

• The network adapter type and Serial Number (i.e., E2210,
E2212, E2219, etc., Serial Number 1234567).

• The software version that appears on the front of the installer
diskette(s).

• Your computer name, model number, and bus architecture.

• The operating system and version number that you are using
(i.e., MS-DOS Version 5.0, OS/2 Version 2.0, etc.).

• The make and model of any other add-in cards in your system
and the version number of any associated software.

You can contact Cabletron Systems Technical Support by:

Phone: [phone]

FAXBack: [phone] Specify Document No. 1101 (listing of
latest driver releases, sample configurations, and keywords)

BBS: [phone] (4 lines available)

Cabletron Technical Support can also be reached over the Internet
by sending email to:
available for anonymous FTP download from

IP address (134.141.72.254)

[e-mail]

.

. Network drivers are also

ctron.com at

CompuServe subscribers can contact Cabletron Technical Support
through the Cabletron Forum by entering:

GO CTRON

at any! prompt.

Page 1 - 2

INTRODUCTION

1.3 E2200 SERIES ADAPTER FEATURES

This section outlines the features of the E2200 Series Ethernet
network adapters. Table 1-1, below, shows the E2200 Series adapter
types and variations.

Table 1-1. Adapter Types and Media

Adapter

Primary Media Secondary Media

Type

E2210 10BASE-T Twisted Pair 10BASE-5 (AUI port)
E2211 10BASE-T Twisted Pair 10BASE-T Twisted Pair
E2212 10BASE-T Twisted Pair 10BASE-2 Coax
E2214 10BASE-T Twisted Pair ST Fiber Optic Port
E2219 10BASE-T Twisted Pair no secondary media
E221W 10BASE-T Twisted Pair Wireless Hub Port

Note that Full-Duplex Switched Ethernet operation is

NOTE

supported on the primary media port of all E2200 Series
adapters.

1.3.1 Connectivity

E2210

The E2210 adapter connects your computer directly to a 10BASE-T
unshielded twisted pair network, or to another Ethernet media
transceiver via the secondary 10BASE-5 AUI port.

E2211

The E2211 adapter has two RJ45 ports, providing your computer
with a redundant 10BASE-T unshielded twisted pair connection to
two Ethernet network links.

Page 1 - 3

INTRODUCTION

E2212

The E2212 adapter connects your computer to a 10BASE-T
Ethernet unshielded twisted pair network, or to a 10BASE-2
Coaxial Thin Ethernet network via the secondary media port.

E2214

The E2214 adapter connects your computer to a 10BASE-T
Ethernet unshielded twisted pair network, or to an ST type Fiber
Optic link via the secondary media port.

E2219

The E2219 adapter connects your computer to a 10BASE-T
Ethernet unshielded twisted pair network. This adapter does not
have a secondary media port.

E221W

The E221W adapter connects your computer to a 10BASE-T
Ethernet unshielded twisted pair network, or to a wireless hub via
the secondary media port (wireless hub interface connector).

All of the E2200 series adapters use the industry standard RJ45
connector for their 10BASE-T ports.

The E2212 adapter’s 10BASE-2 Coaxial port uses a standard BNC
coaxial connector, and the E2210 adapter’s AUI port uses a 15-pin
industry standard type “D” connector. The E221W uses a
proprietary wireless port connector on the secondary media port.

1.3.2 Software

Software drivers for various operating systems are supplied by
Cabletron on floppy diskette media. The drivers support industry
standard Full Duplex Switched Ethernet Protocol.

The

Network Software Installation Guide

, which accompanies
the Cabletron software diskette, explains how to run diagnostics,
and load and configure the various network drivers supplied by
Cabletron.

Page 1 - 4