Cabletron Systems 2E43-51R, 2E43-51 User Manual

2E43-51/2E43-51R SmartSwitch 2100
User’s Guide
E3E1E4
E2
RESET
2E43-51
9032251-04
12
ENET 3 ENET 4
LINK 1
PWR CPU
COM
ENET 1
12
LINK 1
ENET 2
12
12
65
Only qualified personnel should perform installation procedures.

NOTICE

Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made.
The hardware, firmware, or software described in this manual is subject to change without notice. IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL,
INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.
1998 by Cabletron Systems, Inc., P.O. Box 5005, Rochester, NH 03866-5005 All Rights Reserved Printed in the United States of America
Order Number: 9032251-04 September 1998
Cabletron Systems, LANVIEW, QuickSET, S
trademarks and All other product names mentioned in this manual may be trademarks or registered trademarks of
their respective companies.
SmartSwitch
is a trademark of Cabletron Systems, Inc.
ecureFast
, and
SPECTRUM
are registered
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment uses, generates, and can radiate radio frequency energy and if not installed in accordance with the operator’s manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense.
WARNING:
party responsible for compliance could void the user’s authority to operate the equipment.
Changes or modifications made to this device which are not expressly approved by the
Printed on Recycled Paper
2E43-51/2E43-51R User’s Guide i
Notice
INDUSTRY CANADA NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.
VCCI NOTICE
This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.
CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT
IMPORTANT:
This document is an agreement between you, the end user, and Cabletron Systems, Inc. (“Cabletron”) that sets forth your rights and obligations with respect to the Cabletron software program (the “Program”) contained in this package. The Program may be contained in firmware, chips or other media. BY UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND.
Before utilizing this product, carefully read this License Agreement.
ii 2E43-51/2E43-51R User’s Guide
Notice
CABLETRON SOFTWARE PROGRAM LICENSE
1. LICENSE
package subject to the terms and conditions of this License Agreement. You may not copy, reproduce or transmit any part of the Program except as permitted by the
Copyright Act of the United States or as authorized in writing by Cabletron.
2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the
Program.
3. APPLICABLE LA W. This License Agreement shall be interpreted and governed under the laws
and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and venue of the New Hampshire courts.
. You have the right to use only the one (1) copy of the Program provided in this
EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY
1. EXCLUSION OF
writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including its documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO YOU BY CABLETRON IN WRITING, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMP ANYING WRITTEN MA TERIALS, AND ANY A CCOMP ANYING HARDWARE.
2. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL
CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR ON THE DURATION OR LIMITATION OF IMPLIED WARRANTIES, IN SOME INSTANCES THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.
WARRANTY. Except as may be specifically provided by Cabletron in
UNITED STATES GOVERNMENT RESTRICTED RIGHTS
The enclosed product (a) was developed solely at private expense; (b) contains “restricted computer software” submitted with restricted rights in accordance with Section 52227-19 (a) through (d) of the Commercial Computer Software - Restricted Rights Clause and its successors, and (c) in all respects is proprietary data belonging to Cabletron and/or its suppliers.
For Department of Defense units, the product is licensed with “Restricted Rights” as defined in the DoD Supplement to the Federal Acquisition Regulations, Section 52.227-7013 (c) (1) (ii) and its successors, and use, duplication, disclosure by the Government is subject to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at
252.227-7013. Cabletron Systems, Inc., 35 Industrial Way, Rochester, New Hampshire 03867-0505.
2E43-51/2E43-51R User’s Guide iii
Notice
SAFETY INFORMATION
CLASS 1 LASER TRANSCEIVERS
THE FE-100F3 FAST ETHERNET INTERFACE MODULE, FPIM-05 AND
FPIM-07 FDDI PORT INTERFACE MODULES, AND APIM-29 ATM
PORT INTERFACE MODULE USE CLASS 1 LASER TRANSCEIVERS.
READ THE FOLLOWING SAFETY INFORMATION BEFORE
INSTALLING OR OPERATING THESE MODULES.
The Class 1 laser transceivers use an optical feedback loop to maintain Class 1 operation limits. This control loop eliminates the need for maintenance checks or adjustments. The output is factory set, and does not allow any user adjustment. Class 1 Laser transceivers comply with the following safety standards:
• 21 CFR 1040.10 and 1040.11 U.S. Department of Health and Human Services (FDA).
• IEC Publication 825 (International Electrotechnical Commission).
• CENELEC EN 60825 (European Committee for Electrotechnical Standardization). When operating within their performance limitations, laser transceiver output meets the Class 1
accessible emission limit of all three standards. Class 1 levels of laser radiation are not considered hazardous.
SAFETY INFORMATION
CLASS 1 LASER TRANSCEIVERS
LASER RADIATION AND CONNECTORS
When the connector is in place, all laser radiation remains within the fiber. The maximum amount of radiant power exiting the fiber (under normal conditions) is -12.6 dBm or 55 x 10-6 watts.
Removing the optical connector from the transceiver allows laser radiation to emit directly from the optical port. The maximum radiance from the optical port (under worst case conditions) is
0.8 W cm-2 or 8 x 103 W m2 sr-1.
Do not use optical instruments to view the laser output. The use of optical instruments to view laser output increases eye hazard. When viewing the output optical port, power must be removed from the network adapter.
iv 2E43-51/2E43-51R User’s Guide
DECLARATION OF CONFORMITY
Notice
Application of Council Directive(s):
Manufacturer’s Name:
Manufacturer’s Address:
European Representative Name:
European Representative Address:
Conformance to Directive(s)/Product Standards:
Equipment T ype/Environment:
W e the undersigned, hereby declare, under our sole responsibility, that the equipment packaged with this notice conforms to the above directives.
Manufacturer Legal Representative in Europe
89/336/EEC 73/23/EEC
Cabletron Systems, Inc. 35 Industrial Way
PO Box 5005 Rochester, NH 03867
Mr. J. Solari Cabletron Systems Limited
Nexus House, Newbury Business Park London Road, Newbury Berkshire RG13 2PZ, England
EC Directive 89/336/EEC EC Directive 73/23/EEC EN 55022 EN 50082-1 EN 60950
Networking Equipment, for use in a Commercial or Light Environment.
Industrial
Mr. Ronald Fotino Mr. J. Solari
___________________________________ ___________________________________
Full Name Full Name Principal Compliance Engineer Managing Director - E.M.E.A.
___________________________________ ___________________________________
Title Title Rochester, NH, USA Newbury, Berkshire, England
___________________________________ ___________________________________
Location Location
2E43-51/2E43-51R User’s Guide v
Notice
vi 2E43-51/2E43-51R User’s Guide

CONTENTS

CHAPTER 1 INTRODUCTION
1.1 Using This Guide.........................................................................1-1
1.2 Structure of This Guide................................................................1-1
1.3 2E43-51 Overview.......................................................................1-3
1.3.1 Connectivity ....................................................................1-4
1.3.2 Full Duplex Switched Ethernet........................................ 1-4
1.3.3 Auto-Negotiation.............................................................1-4
1.3.4 SmartTrunk.....................................................................1-5
1.3.5 Runtime IP Address Discovery.......................................1-5
1.3.6 Management...................................................................1-6
1.3.7 Switching Options...........................................................1-6
1.3.8 Standards Compatibility..................................................1-6
1.3.9 Year 2000 Compliant......................................................1-7
1.3.10 LANVIEW Diagnostic LEDs............................................1-7
1.4 Optional Features........................................................................1-7
1.4.1 Fast Ethernet Interface Modules..................................... 1-7
1.4.2 High Speed Interface Modules ....................................... 1-8
1.5 Document Conventions............................................................... 1-8
1.6 Getting Help.................................................................................1-9
1.7 Related Manuals........................................................................1-10
CHAPTER 2 NETWORK REQUIREMENTS
2.1 SmartTrunk..................................................................................2-1
2.2 10BASE-T Network .....................................................................2-1
2.3 100BASE-TX Network.................................................................2-2
2.4 100BASE-FX Fiber Optic Network ..............................................2-2
CHAPTER 3 INSTALLATION
3.1 Required Tools............................................................................ 3-1
3.2 Unpacking the 2E43-51...............................................................3-2
3.3 Installing Options.........................................................................3-2
3.4 Installing the 2E43-51..................................................................3-3
3.4.1 Tabletop or Shelf Installation ..........................................3-3
3.4.2 Rackmount Installation ................................................... 3-4
3.4.3 Connecting Power to the Devices................................... 3-7
3.4.3.1 Connecting Power to the 2E43-51 ................. 3-7
3.4.3.2 Connecting Power to the 2E43-51R...............3-8
2E43-51/2E43-51R User’s Guide vii
Contents
3.5 Connecting to the Network...........................................................3-9
3.5.1 Connecting Cables to ENETs 1 Through 4.....................3-9
3.5.2 Connecting a UTP Segment to the FE-100TX..............3-11
3.5.3 Connecting a Fiber Optic Segment to the
FE-100FX and FE-100F3..............................................3-14
3.6 Completing the Installation.........................................................3-16
CHAPTER 4 TROUBLESHOOTING
4.1 Using LANVIEW...........................................................................4-1
4.2 FE-100TX LED.............................................................................4-4
4.3 Troubleshooting Checklist............................................................4-6
4.4 Using the RESET Button .............................................................4-7
CHAPTER 5 LOCAL MANAGEMENT
5.1 Overview......................................................................................5-1
5.2 Local Management Keyboard Conventions.................................5-2
5.3 Management Terminal Setup.......................................................5-3
5.3.1 Console Cable Connection..............................................5-4
5.3.2 Management Terminal Setup Parameters ......................5-5
5.3.3 Telnet Connections .........................................................5-6
5.3.4 Monitoring an Uninterruptible Power Supply...................5-7
5.4 Accessing Local Management.....................................................5-8
5.4.1 Navigating Local Management Screens..........................5-9
5.4.2 Selecting Local Management Menu Screen Items........5-11
5.4.3 Exiting Local Management Screens..............................5-11
5.5 Device Menu Screen..................................................................5-13
5.6 Device Configuration Menu Screen ...........................................5-15
5.7 General Configuration Screen ...................................................5-17
5.7.1 Setting the IP Address...................................................5-20
5.7.2 Setting the Subnet Mask...............................................5-21
5.7.3 Setting the Default Gateway..........................................5-22
5.7.4 Setting the TFTP Gateway IP Address .........................5-23
5.7.5 Setting the Device Date.................................................5-24
5.7.6 Setting the Device Time................................................5-24
5.7.7 Entering a New Screen Refresh Time...........................5-25
5.7.8 Setting the Screen Lockout Time..................................5-25
5.7.9 Setting the Operational Mode........................................5-26
5.7.10 Configuring the COM Port.............................................5-27
5.7.11 Clearing NVRAM...........................................................5-29
5.7.12 Enabling/Disabling IP Fragmentation............................5-30
viii 2E43-51/2E43-51R User’s Guide
Contents
5.8 SNMP Community Names Screen............................................ 5-31
5.8.1 Establishing Community Names...................................5-32
5.9 SNMP Traps Screen..................................................................5-34
5.9.1 Configuring the Trap Table...........................................5-35
5.10 Switch Configuration Screen..................................................... 5-36
5.10.1 Setting the STA............................................................. 5-38
5.10.2 Setting the Age Time Field ........................................... 5-38
5.10.3 Setting (Enabling or Disabling) the Port Status ............ 5-39
5.11 Device Specific Configuration Menu Screen............................. 5-39
5.12 System Resources Screen........................................................5-41
5.12.1 Setting the Reset Peak Switch Utilization.....................5-43
5.13 High Speed Interface Configuration Menu Screen....................5-44
5.14 High Speed Interface Configuration Screen..............................5-46
5.14.1 Configuring an FE-100FX or FE-100F3........................5-48
5.14.1.1 Setting the FE-100FX or FE-100F3
Operational Mode.........................................5-49
5.14.2 Configuring an FE-100TX.............................................5-49
5.14.2.1 Setting the FE-100TX Operational Mode.....5-49
5.14.2.2 Setting the FE-100TX Advertised Ability......5-50
5.15 FLASH Download Screen..........................................................5-50
5.15.1 Image File Download Using BootP...............................5-53
5.15.2 Image File Download Using TFTP................................ 5-53
5.15.3 Image File Download Using Runtime ........................... 5-54
5.16 Port Redirect Function Screen ..................................................5-55
5.16.1 Displaying the Source and Destination Entries............. 5-57
5.16.2 Changing Source and Destination Ports....................... 5-58
5.17 Broadcast Suppression Screen.................................................5-58
5.17.1 Setting the Threshold.................................................... 5-60
5.17.2 Setting the Reset Peak.................................................5-60
5.18 Repeater Configuration Menu Screen.......................................5-61
5.19 Repeater Level Security Configuration......................................5-62
5.19.1 Setting the Repeater Level Security .............................5-64
5.20 Port Level Security Configuration Screen..................................5-65
5.20.1 Setting the Port Level Security ..................................... 5-68
5.21 Device Statistics Menu Screen..................................................5-69
5.22 Switch Statistics Screen............................................................ 5-71
5.23 Interface Statistics Screen.........................................................5-73
5.23.1 Displaying Interface Statistics.......................................5-76
5.23.2 Using the Clear Counters Command............................5-76
5.24 RMON Statistics Screen............................................................5-77
5.24.1 Displaying RMON Statistics.......................................... 5-80
5.24.2 Using the Clear Counters Command............................5-81
2E43-51/2E43-51R User’s Guide ix
Contents
5.25 Repeater Statistics Screen ........................................................5-81
5.25.1 Displaying Repeater Statistics.......................................5-84
5.25.2 Using the Clear Counters Command ............................5-84
5.26 Network Tools............................................................................5-85
5.26.1 Built-in Commands........................................................5-86
5.26.2 Special Commands.......................................................5-94
APPENDIX A SPECIFICATIONS
A.1 Device Specifications.................................................................. A-1
A.2 Physical Properties .....................................................................A-1
A.3 Electrical Specifications ..............................................................A-1
A.4 Environmental Requirements...................................................... A-2
A.5 Input/Output Ports....................................................................... A-2
A.6 COM Pinout Assignments........................................................... A-2
A.7 Regulatory Compliance............................................................... A-3
APPENDIX B FE-100TX, FE-100FX, AND FE-100F3
SPECIFICATIONS
B.1 FE-100TX.................................................................................... B-1
B.2 FE-100FX.................................................................................... B-2
B.3 FE-100F3.................................................................................... B-3
APPENDIX C OPTIONAL INSTALLATIONS AND
MODE SWITCH BANK SETTINGS
C.1 Required Tools............................................................................C-1
C.2 Removing the Chassis Cover .....................................................C-2
C.2.1 Setting the Mode Switch.................................................C-4
C.3 Installing Optional Fast Ethernet Interface Modules...................C-7
INDEX
x 2E43-51/2E43-51R User’s Guide
CHAPTER 1

INTRODUCTION

Welcome to the
2E43-51/2E43-51R SmartSwitch 2100 User’s Guide.
This guide provides the necessary documentation to install and operate the 2E43-51 and the 2E43-51R SmartSwitch 2100 devices and provides information concerning network requirements, installation, troubleshooting, and the use of Local Management.

1.1 USING THIS GUIDE

Read through this guide to completely understand the 2E43-51 and 2E43-51R capabilities and Local Management functions. A general working knowledge of Ethernet and IEEE 802.3 type data communications networks and their physical layer components is helpful when using this device.
NOTE
Unless it is noted differently, the information in this guide applies to both the 2E43-51 and the 2E43-51R SmartSwitch 2100 devices. Unless the information pertains only to the 2E43-51 or the 2E43-51R, the device is referred to as either the “2E43-51” or the “device”.

1.2 STRUCTURE OF THIS GUIDE

This guide is organized as follows:
Chapter 1,
Introduction
, outlines the contents of this manual and briefly
describes the 2E43-51 features. Directions about how to obtain additional help and a list of related manuals are also included.
Chapter 2,
Network Requirements
, explains the network requirements
to consider before installing the 2E43-51.
Chapter 3,
Installation
, provides instructions on how to install the
2E43-51 and connect segments to the device.
Chapter 4,
Troubleshooting
, describes the function of the LANVIEW
LEDs, which can help to quickly diagnose network/operational problems.
2E43-51/2E43-51R User’s Guide 1-1
Chapter 1:
Introduction
Chapter 5,
Local Management
, describes how to access and use Local
Management to configure and manage the 2E43-51.
Appendix A,
Specifications
, contains information on functionality and operating specifications, connector pinouts, environmental requirements, and physical properties.
Appendix B,
FE-100TX, FE-100FX, and FE-100F3 Specifications
, contains information about FE-100TX pinouts and information concerning cable types used with the FE-100FX and FE-100F3.
Appendix C,
Optional Installations and Mode Switch Bank Settings
, describes how to install optional Fast Ethernet Interface Modules and ho w to set the Mode Switch.
1-2 2E43-51/2E43-51R User’s Guide
2E43-51 Overview

1.3 2E43-51 OVERVIEW

The 2E43-51 (Figure 1-1) is a repeater/switch device that provides four Ethernet networks (MicroLANs ENET 1 through 4), each consisting of 12 repeater ports that share a bandwidth of 10 Mbps. Each Ethernet network supports 802.1D switching (bridging), and Cabletron Systems SecureFast Switching Virtual Network technology.
Interface Receive (RX) Transmit (TX) LEDs
E3E1E4
2E43-51
E2
RESET
Port LINK LEDs (12 ports/MicroLAN)
LINK 1
PWR CPU
COM
System LEDs COM Port
RESET Button
12
LINK 1LINK 1
ENET 3 ENET 4
ENET 1
12
LINK 1
MicroLANs (ENET 1 - 4)
ENET 2
Figure 1-1 The 2E43-51
Optional HSIM Slot
12
12
Receive (RX) Transmit (TX) LEDs
65
Optional Fast Ethernet Interface Module Slots 5 & 6
2251-00
The 2E43-51 also has two slots (5 and 6) for optional 10/100 Fast Ethernet Interface Modules, and another slot for an optional High Speed Interface Module (HSIM).
The device can switch each Ethernet network (ENET 1 through ENET 4) to one another, to the optional interface modules in slots 5 and 6, and to the HSIM slot. The optional Fast Ethernet Interface Modules provide uplinks to 100BASE-TX or 100BASE-FX Fast Ethernet networks. The HSIMs provide additional connectivity to various networking technologies such as Asynchronous Transfer Mode (ATM), Fiber Distributed Data Interface (FDDI), and Wide Area Network (WAN).
The 2E43-51 may be used as a tabletop unit or can be installed in a standard 19-inch rack using the supplied rack mounting hardware.
The 2E43-51 device has one universal ac power supply with automatic voltage sensing that allows operation using 100–125 or 200–240 Vac, 50/60 Hz.
2E43-51/2E43-51R User’s Guide 1-3
Chapter 1:
The 2E43-51R has two power supplies. The power supplies load share 50% (+/-5%) of the power required by the device. If one power supply fails, the remaining power supply assumes the entire load of the device without interruption to network traffic. Each power supply module supports its own ac input connection, which allows the user to connect each power supply to a different ac power circuit.
Introduction

1.3.1 Connectivity

The 2E43-51 connects to Ethernet networks or workstations through four 50-pin RJ21 connectors. Each connector serves as a 12-port Ethernet 10 Mbps MicroLAN.
Both of the devices have two front panel slots (ports 5 and 6) for optional Fast Ethernet Interface Modules to support an uplink to 100 Mbps Fast Ethernet backbones or a high speed connection to a local server. There is also space for an optional HSIM to provide additional connectivity to various networking technologies.

1.3.2 Full Duplex Switched Ethernet

The optional Fast Ethernet Interface Modules for the 2E43-51 can be configured to operate in Full Duplex Switched Ethernet mode, which provides 200 Mbps of bandwidth.

1.3.3 Auto-Negotiation

The repeater ports and Fast Ethernet Interface Modules can auto-negotiate the type of connection required to provide a link to another device. During Auto-Negotiation, two devices automatically exchange information “telling” each other what their operating capabilities are. The Auto-Negotiation feature targets the maximum capabilities that can be reached between the two devices. For example, an FE-100TX Fast Ethernet Interface Module in a 2E43-51 can adjust to 100 Mbps when the device on the other end of the connection can also adjust to 100 Mbps. If the device on the other end of the connection can only operate at 10 Mbps, then the FE-100TX simply adjusts to 10 Mbps operation.
1-4 2E43-51/2E43-51R User’s Guide
2E43-51 Overview
When Auto-Negotiation is supported at both ends of a link, the two devices dynamically adjust to full or half duplex operation based on the maximum capability that can be reached between the two devices. If the device connected to the FE-100TX cannot auto-negotiate, the FE-100TX Fast Ethernet Interface Module operates according to the capabilities of the other device.

1.3.4 SmartTrunk

SmartTrunk, also referred to as SmartTrunking, is Cabletron Systems’ terminology for load balancing or load sharing. SmartTrunk technology provides an easy-to-implement mechanism to group, or aggregate, multiple physical links together to scale the backbone bandwidth beyond the limitations of a single link. All links are user-configurable so administrators can scale the backbone bandwidth by adding SmartTrunk links. The SmartTrunk benefits are as follows:
All purchased bandwidth is used.
Distributed, resilient links increase reliability and performance.
Multiple technologies are supported within a single trunk for maximum flexibility.
For more information about SmartTrunk, refer to the Cabletron Systems
SmartTrunk User’s Guide
.

1.3.5 Runtime IP Address Discovery

This feature enables the 2E43-51 to automatically accept an IP address from a Boot Strap Protocol (BootP) server on the network into NVRAM without requiring a user to enter an IP address through Local Management.
When the 2E43-51 is connected to the network and powered up, Runtime IP Address Disco very (RAD) checks the 2E43-51 for an IP address. If one has not yet been assigned (2E43-51 IP address set to 0.0.0.0), RAD checks to see if any of the 2E43-51 interfaces have a link. If so, RAD sends out Reverse Address Resolution Protocol (RARP) and BootP requests to obtain an IP address from a BootP server on the network.
2E43-51/2E43-51R User’s Guide 1-5
Chapter 1:
The RAD requests start out at an interval of 1 second. The interval then doubles after every transmission until an interval of 300 seconds is reached. At this point, the interval remains at 300 seconds. The RAD requests continue until an IP address is received from a BootP server, or an IP address is entered using Local Management.
Introduction

1.3.6 Management

Management of the 2E43-51 is accomplished using SNMP compliant management tools for in-band Local Management. Out-of-band Local Management is provided through the RJ45 COM port on the front panel using a VT100 terminal or a VT100 terminal emulator. In-band remote management is possible through any SNMP compliant Network Management Software.
Local Management provides the ability to manage the 2E43-51 and any of the optional Fast Ethernet Interface Modules installed in ports 5 and 6, and the optional High Speed Interface Module (HSIM).
The associated HSIM user’s guide provides detailed information about the HSIM Local Management.

1.3.7 Switching Options

The 2E43-51 provides 802.1D switching, 802.1Q switching or SecureFast Switching Virtual Network Services between all of the front panel interfaces including Fast Ethernet Interface Modules and High Speed Interface Module (HSIM).
IEEE 802.1Q switching and SecureFast switching allow for future migration to Virtual Network technologies without requiring the replacement of existing equipment.

1.3.8 Standards Compatibility

The 2E43-51 provides IEEE 802.1D Spanning Tree Algorithm (STA) support to enhance the overall reliability of the network and protect against “loop” conditions. The 2E43-51 also supports 100BASE-TX and 100BASE-FX Fast Ethernet standards and a wide variety of industry standard MIBs including RFC 1213 (MIB II), RFC 1757 (RMON), RFC 1493 (Bridge MIB) and RFC 1354 (FIB MIB). A full suite of Cabletron Systems Enterprise MIBs provide a wide array of statistical information to enhance troubleshooting.
1-6 2E43-51/2E43-51R User’s Guide
Optional Features

1.3.9 Year 2000 Compliant

The 2E43-51 has an internal clock that can maintain the current time and date beyond the year 1999.

1.3.10 LANVIEW Diagnostic LEDs

LANVIEW diagnostic LEDs serve as an important troubleshooting aid by providing an easy way to observe the status of indi vidual ports and overall network operations.

1.4 OPTIONAL FEATURES

Options for the 2E43-51 include the following:
Fast Ethernet Interface Modules
High Speed Interface Modules

1.4.1 Fast Ethernet Interface Modules

Cabletron Systems provides Fast Ethernet Interface Modules to support uplinks to 100 Mbps Fast Ethernet backbones or high speed connections to local servers. The Fast Ethernet Interface Modules are listed in
Table 1-1.
.
P/N Description Application
FE-100TX
FE-100FX
FE-100F3
Table 1-1 Fast Ethernet Interface Modules
Supports Category 5 Unshielded Twisted Pair Uses RJ45 connector
Uses SC connector
Uses SC connector
(UTP) cabling, which has an impedance of 85 to
111 ohms, and Shielded Twisted Pair (STP)
cabling.
Supports multimode fiber optic cabling.
Supports single mode fiber optic cabling.
2E43-51/2E43-51R User’s Guide 1-7
Chapter 1:
Introduction

1.4.2 High Speed Interface Modules

High Speed Interface Modules (HSIMs) are available from Cabletron Systems for additional connectivity to various networking technologies. The HSIMs available for the 2E43-51 are listed in the Release Notes shipped with the 2E43-51.

1.5 DOCUMENT CONVENTIONS

The following conventions are used throughout this document:
Note
NOTE
TIP
symbol. Calls the reader’s attention to any item of
information that may be of special importance.
Tip
symbol. Conveys helpful hints concerning procedures or
actions.
Caution
damage to the equipment.
!
CAUTION
Electrical Hazard Warning
that could result in personal injury or death due to an electrical hazard.
Warning
WARNING
1-8 2E43-51/2E43-51R User’s Guide
personal injury or death.
symbol. Contains information essential to avoid
symbol. Warns against an action
symbol. Warns against an action that could result in
Getting Help

1.6 GETTING HELP

For additional support related to this device or document, contact the Cabletron Systems Global Call Center:
World Wide Web http://www.cab letron.com/ Phone (603) 332-9400 Internet mail support@cabletron.com FTP ftp://ftp.cabletron.com/
Login Password
To send comments or suggestions concerning this document, contact the Cabletron Systems Technical Writing Department via the following email address: TechWriting@cabletron.com
Make sure to include the document Part Number in the email message.
Before calling the Cabletron Systems Global Call Center, have the following information ready:
Your Cabletron Systems service contract number
A description of the failure
anonymous your email address
A description of any action(s) already taken to resolve the problem
(e.g., changing mode switches, rebooting the unit, etc.)
The serial and revision numbers of all involved Cabletron Systems
products in the network
A description of your network environment (layout, cable type, etc.)
Network load and frame size at the time of trouble (if known)
The device history (i.e., have you returned the device before, is this a
recurring problem, etc.)
Any previous Return Material Authorization (RMA) numbers
2E43-51/2E43-51R User’s Guide 1-9
Chapter 1: Introduction

1.7 RELATED MANUALS

The following manuals may help to set up, control, and manage the 2E43-51:
Cabletron Systems HSIM-A6DP User’s Guide Cabletron Systems HSIM-F6 User’s Guide Cabletron Systems HSIM-FE6 User’s Guide Cabletron Systems HSIM-W87
User’s Guide
Cabletron Systems HSIM-G01/G09 User’s Guide Cabletron Systems Ethernet Technology Guide Cabletron Systems Cabling Guide Cabletron Systems Port Based VLAN User’s Guide Cabletron Systems SmartTrunk User’s Guide These manuals can be obtained from the World Wide Web in Adobe
Acrobat Portable Document Format (PDF) at the following site:
http://www.cabletron.com/
NOTE
All documentation for the Cabletron Systems SecureF ast VLAN Manager software is contained on the VLAN Manager CD-ROM.
Documents for the Cabletron Systems HSIM-W6 and HSIM-W84 devices are contained on the QuickSET CD-ROM and are also available on the World Wide Web at: http://www.cabletron.com/.
1-10 2E43-51/2E43-51R User’s Guide
CHAPTER 2

NETWORK REQUIREMENTS

This chapter contains networking guidelines. Before installing and using the 2E43-51 or an optional Fast Ethernet Interface Module (FE-100TX, FE-100FX, or FE-100F3), review the requirements and specifications outlined in this chapter concerning the following:
SmartTrunk (Section 2.1)
10BASE-T Twisted Pair Network (Section 2.2)
100BASE-TX Twisted Pair Network (Section 2.3)
100BASE-FX Fiber Optic Network (Section 2.4)
The network installation must meet the guidelines to ensure satisfactory performance of this equipment. Failure to follow the guidelines may produce poor network performance.
NOTE
The Cabletron Systems
Guide
, referred to in the follo wing sections, can be f ound on the Cabletron Systems World Wide Web site: http://www.cabletron.com/
Cabling Guide
and
SmartTrunk User’s

2.1 SmartTrunk

T o connect the 2E43-51 into a netw ork so that it can take adv antage of the SmartTrunk feature, there are certain rules concerning port connections and configurations that must be followed for proper operation. Refer to the Cabletron Systems SmartTrunk User’s Guide for additional information.

2.2 10BASE-T NETWORK

When connecting a 10BASE-T segment to any of the 2E43-51 ports (ENET 1 through ENET 4), ensure that the network meets IEEE 802.3 Ethernet network requirements for 10BASE-T. Refer to the Cabletron Systems Cabling Guide for details.
2E43-51/2E43-51R User’s Guide 2-1
Chapter 2: Network Requirements

2.3 100BASE-TX NETWORK

The 2E43-51, with an FE-100TX installed in slots 5 and/or 6, provides an RJ45 connection that supports UTP cabling, which has an impedance of 85 to 111 ohms. The device at the other end of the twisted pair segment must meet IEEE 802.3u 100BASE-TX Fast Ethernet network requirements for the devices to operate at 100 Mbps. Refer to the Cabletron Systems Cabling Guide for details.
NOTE
The 2E43-51 with an FE-100TX installed is capable of operating at either 10 or 100 Mbps. The FE-100TX can automatically sense the speed of the other device and adjusts its speed accordingly.

2.4 100BASE-FX FIBER OPTIC NETWORK

Slots 5 and 6 of the 2E43-51 can also support the Cabletron Systems FE-100FX and FE-100F3 fiber optic interface modules. The device at the other end of the fiber optic segment must meet the 100BASE-FX Fast Ethernet network requirements to operate at 100 Mbps. Refer to the Cabletron Systems Cabling Guide for details.
Multimode Mode Fiber Optic Cable Length
The maximum multimode fiber optic cable length of a 100BASE-FX segment is covered in the Cabletron Systems Cabling Guide.
Single Mode Fiber Cable Lengths
The maximum length of a 100BASE-FX segment may be no more than 412 meters between Data Terminal Equipment (DTE to DTE) in half duplex mode or 20 km (DTE to DTE) in full duplex mode.
2-2 2E43-51/2E43-51R User’s Guide
CHAPTER 3

INSTALLATION

Only qualified personnel should install the 2E43-51.
This chapter provides the instructions required to install the 2E43-51. Follow the order of the sections listed below to correctly install the 2E43-51.
Required Tools (Section 3.1)
Unpacking the 2E43-51 (Section 3.2)
Installing Options (Section 3.3)
Installing the 2E43-51 (on a shelf or tabletop, or into a standard rack)
(Section 3.4)
Connecting to the Network (Section 3.5)
Completing the Installation (Section 3.6)

3.1 REQUIRED T OOLS

A Phillips screwdriver is required to install the 2E43-51 in a rack.
2E43-51/2E43-51R User’s Guide 3-1
Chapter 3: Installation

3.2 UNPACKING THE 2E43-51

To unpack the 2E43-51 and verify the contents of the shipment, proceed as follows:
1. Open the carton and remove the packing material protecting the
2E43-51.
2. Verify the contents of the carton as listed in Table 3-1.
Table 3-1 Contents of 2E43-51 Carton
Item Quantity
2E43-51 1 Antistatic wrist strap 1 Console Cable Kit 1 RJ21 Angle Adapter 4 Rackmount Kit 1 Strain Relief Bracket 1 Release Notes 1 Power Cord (2E43-51 only) 1 Power Cord (2E43-51R only) 2
3. Remove the black and yellow tape seal on the non-conductive bag to
remove the 2E43-51.
4. Perform a visual inspection of the device for any signs of physical
damage. If there are any items missing or damaged, contact the Cabletron Systems Global Call Center as described in Section 1.6.

3.3 INSTALLING OPTIONS

NOTE
3-2 2E43-51/2E43-51R User’s Guide
Install any optional equipment before proceeding to
Section 3.4.
Installing the 2E43-51
If the 2E43-51 is to be installed with an optional Fast Ethernet Interface Module, refer to Appendix C for installation instructions. The installation instructions for the HSIMs are in the associated HSIM user’s guide.

3.4 INSTALLING THE 2E43-51

The 2E43-51 may be installed on a tabletop, shelf, or in a 19-inch rack.
Section 3.4.1 describes a tabletop or shelf installation, and Section 3.4.2
describes the rackmount installation.
To prevent possible personal injury and/or damage to the unit, do NOT connect power to the 2E43-51 until instructed to do so.

3.4.1 Tabletop or Shelf Installation

The following two subsections provide guidelines for installation on a tabletop or shelf.
Guidelines for Tabletop and Shelf Installations
Tabletop and shelf installations must be within reach of the network cabling and meet the requirements listed below:
Locate the 2E43-51 within seven feet of an appropriately grounded
power receptacle that meets the power supply requirements listed in
Appendix A.
In a shelf installation, the shelf must support 13.6 kg (30 lb) of static
weight for each 2E43-51.
Maintain a temperature of between 5°C (41°F) and 40°C (104°F) at
the installation site with fluctuations of less than 10°C (18°F) per hour.
Maintain a 2-inch clearance from the left, right, and rear sides of the
device to provide adequate ventilation.
Installation
For a tabletop or shelf installation, locate the 2E43-51 within seven feet of its power source and with an unrestricted free surface area as shown in
Figure 3-1. Proceed to Section 3.4.3 for power connection instructions.
To ensure proper ventilation and prevent overheating, leave a minimum clearance space of 5.1 cm (2.0 in) at the left, right,
!
CAUTION
2E43-51/2E43-51R User’s Guide 3-3
and rear of the 2E43-51.
Chapter 3: Installation
B
A
A = 15 cm (6 in)
2E43-51
E3E1E4
12
E2
LINK 1
PWR
RESET
CPU
COM
LINK 1LINK 1
ENET 3 ENET 4
12
LINK 1
ENET 1
C
12
12
ENET 2
65
D
B = 57.2 cm (22.5 in) C = 53 cm (21 in) D = 213 cm (7 ft)
22511-06
Figure 3-1 Tabletop or Shelf Installation

3.4.2 Rackmount Installation

To install the 2E43-51 in a 19-inch rack, the device is shipped with a rackmount kit containing the rackmount brackets, mounting screws, and a strain-relief bracket for cable management.
Guidelines for the Rackmount Installation
The installation site must be within reach of the network cabling and meet the requirements listed below:
An appropriate grounded power receptacle must be located within seven feet of the location.
Maintain a temperature of between 5°C (41°F) and 40°C (104°F) at the installation site with fluctuations of less than 10°C (18°F) per hour.
To ensure proper ventilation and prevent overheating, leave a minimum clearance space of 5.1 cm (2.0 in) at the left, right,
!
CAUTION
WARNING
3-4 2E43-51/2E43-51R User’s Guide
and rear of the 2E43-51.
Before installing the 2E43-51 into a rack, ensure that the rack supports the device(s) without compromising the stability of the rack. Otherwise, personal injury and/or equipment damage may result.
Installing the 2E43-51
Installation
Rack mounting the 2E43-51 involves the following:
Attaching the strain-relief bracket
Rack mounting the 2E43-51 (attaching the mounting brackets and
fastening the 2E43-51 to the rack)
Attaching the Strain-Relief Bracket
Attach the strain-relief bracket to the front of the 2E43-51 as follows:
1. Locate the strain-relief bracket and four 8-32 x 5/16-inch pan-head
screws in the rackmount kit.
Do not attempt to attach the strain-relief bracket with screws other than the 8-32 x 5/16-inch screws included with the
!
CAUTION
2E43-51. Use of longer screws may damage the unit.
2. Attach the strain-relief bracket to the bottom of the 2E43-51 using the
four 8-32 x 5/16-inch pan-head screws (Figure 3-2).
Screws (4)
Strain-Relief Bracket
65
ENET 2
12
12
LINK 1
LINK 1LINK 1
ENET 1
12
ENET 3 ENET 4
12
COM CPU PWR
LINK 1
2E43-51
RESET
E2
E3E1E4
2251-47
Figure 3-2 Attaching the Strain-Relief Bracket
2E43-51/2E43-51R User’s Guide 3-5
Chapter 3: Installation
Rack Mounting the 2E43-51
Proceed as follows to install the 2E43-51 into a 19-inch rack.
1. Remove and discard the four cover screws (two from each side)
located along the front edges of each side of the 2E43-51.
2. Locate the four 6-32 x 3/8-inch flathead cover replacement screws in
the rackmount kit. Use these screws to attach the rackmount brackets to the 2E43-51 as shown in Figure 3-3.
Rackmount Brackets (2)
12
2E43-51
E3E1E4
E2
RESET
COM
ENET 3 ENET 4
LINK 1
PWR CPU
ENET 1
LINK 1LINK 1
12
LINK 1
ENET 2
12
12
65
Screws (4)
2251-04
Figure 3-3 Installing the Rackmount Brackets
3. With the mounting brackets installed, position the 2E43-51 between
the vertical frame members of the 19-inch rack and fasten it securely with user supplied mounting screws as shown in Figure 3-4.
19-Inch Rack
12
LINK 1LINK 1
12
LINK 1
2E43-51
E3E1E4
E2
RESET
COM
ENET 3 ENET 4
LINK 1
PWR CPU
ENET 1
Screws (4)
Figure 3-4 Installing the 2E43-51 in a Rack
ENET 2
12
12
65
2251-03
3-6 2E43-51/2E43-51R User’s Guide
Installing the 2E43-51

3.4.3 Connecting Power to the Devices

NOTE
The 2E43-51 has one power supply while the 2E43-51R has two. The power supplies have automatic voltage sensing that allows connection to power sources ranging from 100–125 Vac,
2.0 A or 200–240 Vac, 1.0 A, 50/60 Hz.
To connect power to the 2E43-51, proceed to Section 3.4.3.1. To connect power to the 2E43-51R, proceed to Section 3.4.3.2.
3.4.3.1 Connecting Power to the 2E43-51
To connect the 2E43-51 to a power source, proceed as follows:
1. Plug the power cord into a grounded wall outlet. The PWR LED turns
on (green) and the CPU LED turns on (green) briefly.
NOTE
2. Observe the LANVIEW LEDs. After a successful boot, the CPU LED
It takes approximately one minute for the 2E43-51 to boot up.
turns on (green). If the CPU LED is not green after one minute, check the power cord connection and power source. If the CPU LED is still not green, contact the Cabletron Systems Global Call Center. Refer to
Section 1.6 for details.
2E43-51/2E43-51R User’s Guide 3-7
Chapter 3: Installation
3.4.3.2 Connecting Power to the 2E43-51R
To connect the 2E43-51R to the power sources, proceed as follows:
1. Plug each power cord into a grounded wall outlet, see Figure 3-5. To
take advantage of the load sharing and redundancy capabilities, each power cord must be plugged into a dedicated ac outlet. The POWER LED turns on (green) and the CPU LED turns on (green) briefly.
8H02-26R
Primary
Redundant
Figure 3-5 2E43-51R Rear View
1960-62
It takes approximately one minute for the 2E43-51R to boot up.
NOTE
2. Observe the LANVIEW LEDs. After a successful boot, the CPU LED
turns on (green). If the PWR LED is not green after one minute and turns amber, there is no power redundancy. Check the power cord connections and the power source. If there are no problems with the power cord connections or power source and the PWR LED is still not green, contact the Cabletron Systems Global Call Center. Refer to
Section 1.6 for details.
3-8 2E43-51/2E43-51R User’s Guide
Connecting to the Network

3.5 CONNECTING TO THE NETWORK

This section provides the procedures for connecting UTP and fiber optic segments from the network or other devices to the 2E43-51.
NOTE
If the 2E43-51 is being installed in a network using SmartTrunking, there are rules concerning the network cable and port configurations that must be followed for SmartTrunking to operate properly. Before connecting the cables, refer to the configuration information.
SmartTrunk User’s Guide
for the
Ports 1 through 4 are MicroLANs (ENET 1 through 4) with each one consisting of 12 UTP connections via a 50-pin RJ21 connector. Ports 5 and 6 support FE-100TX, FE-100FX, or FE-100F3 Fast Ethernet Interface Modules.
The FE-100TX has an RJ45 connector for a UTP cable connection. The FE-100FX and FE-100F3 have SC connectors for fiber optic cable connections.
Refer to Section 3.5.1 to make UTP connections to ENET 1 through ENET 4.
Refer to Section 3.5.2 to make a UTP connection to an FE-100TX in port slot 5 or 6.
Refer to Section 3.5.3 to make a fiber optic cable connection to an FE-100FX or FE-100F3 in port slot 5 or 6.
Refer to the associated High Speed Interface Module user’ s guide to make connections to an optional High Speed Interface Module installed in the HSIM slot.

3.5.1 Connecting Cables to ENETs 1 Through 4

The device uses four RJ21 connectors for the MicroLAN (ENET) connections, each supporting 12 Ethernet ports. All Ethernet ports have internal crossovers.
2E43-51/2E43-51R User’s Guide 3-9
Chapter 3: Installation
To connect an RJ21, proceed as follows:
1. Ensure that the device connected to the other end of the segment is
powered on.
2. If using an RJ21 straight connector, plug it into the appropriate RJ21
port as shown in Figure 3-6 or, if using the RJ21 angle adapter supplied with the device, insert the RJ21 angle adapter as shown in
Figure 3-7. The RJ21 angle adapter allows the cables to be dressed
along the front of the device and easily attached to the strain-relief bracket when using a right-angled RJ21 connector.
LINK 1
ENET 4
LINK 1 12
ENET 2
Screw
Figure 3-6 Straight Cable Connection
LINK 1
ENET 4
LINK 1 12
ENET 2
Screw
Clip
RJ21 Angle Adapter
12
65
Screw
RJ21
2251-10
12
65
Screw
Clip
RJ21Right-Angled Connector
22511-73
Figure 3-7 Connection Using the RJ21 Angle Adapter
3-10 2E43-51/2E43-51R User’s Guide
Connecting to the Network
3. Tighten the two screws on the RJ21 straight cable connector or RJ21
angle adapter, as applicable, to secure it to the device.
NOTE
The cable pinouts for a 25 pair cab le (RJ21) can be found in the Cabletron Systems details on how to obtain this document.
Cabling Guide.
Refer to Section 1.7 for
4. If using the RJ21 angle adapter, plug in the RJ21 right-angled
connector until the two retaining clips, shown in Figure 3-7, snap into place.
5. Verify that a link exists by checking that the LINK LED on the
2E43-51 for that port is on (solid green). If the LINK LED is off, perform the following steps until it is on:
a. Verify that the 10BASE-T device at the other end of the twisted
pair segment is on and connected to the segment.
b. Verify that all connectors on the twisted pair segment have the
proper pinouts and check the cable for continuity.
c. Check that the twisted pair connection meets the dB loss and cable
specifications outlined in Chapter 2.
If a link is not established, contact Cabletron Systems Global Call Center. Refer to Section 1.6 for details.
6. Repeat steps 1 through 4 above, until all connections have been made.

3.5.2 Connecting a UTP Segment to the FE-100TX

The FE-100TX supports Category 5 UTP cabling, which has an impedance of 85 to 11 ohms.
An FE-100TX installed in port slot 5 and/or 6 has an internal crossover switch. When connecting a workstation, use a straight-through cable and set the Fast Ethernet Interface Module crossover switch shown in
Figure 3-8 to the crossed over position marked with X. When connecting
networking devices, such as another bridge, repeater, or router, use a straight-through cable and set the Fast Ethernet Interface Module crossover switch shown in Figure 3-8 to the straight-through position (not crossed over), marked with =.
2E43-51/2E43-51R User’s Guide 3-11
Chapter 3: Installation
Position X (crossed over)
1. RX+
2. RX-
3. TX+
4. NC
5. NC
6. TX-
7. NC
x
FE-100TX
=
8. NC
Figure 3-8 FE-100TX Crossover Switch
Position = (not crossed over)
1. TX+
10
2. TX-
100
3. RX+
4. NC
5. NC
6. RX-
7. NC
8. NC
16651_05
A schematic of a crossover cable is shown in Figure 3-9. If the wires do not cross over, use the switch on the FE-100TX to internally cross over the RJ45 port.
NOTE: RX+/RX– and TX+/TX– must share a common color pair.
Figure 3-9 Cable Pinouts - RJ45 Crossover Cable
RJ45 Port RX+ RX– 2
TX+
TX–
TO
10BASE-T Device Port
1
3 6
RJ45 to RJ45
TO
1 2
3 6
RX+ RX–
TX+ TX–
2251-31
Connect an FE-100TX to a twisted pair segment as follows:
1. Ensure that the device connected to the other end of the segment is
powered on.
2. Connect the twisted pair segment to the module by inserting the RJ45
connector on the twisted pair segment into the RJ45 port on the module shown in Figure 3-10.
3-12 2E43-51/2E43-51R User’s Guide
=
FE-100TX
5
Connecting to the Network
x
10
100
6
RX LED
TX LED
RJ45
2251-14
Figure 3-10 FE100-TX Port
3. Verify that a link exists by checking that the port RX LED is on
(flashing amber, blinking green, or solid green). If the RX LED is off and the TX LED is not blinking amber, perform the following steps until the RX LED is on:
a. Verify that the 100BASE-TX de vice at the other end of the twisted
pair segment is powered up.
b. Verify that the RJ45 connector on the twisted pair segment has the
proper pinouts.
c. Check the cable for continuity. d. Make sure that the twisted pair connection meets the cable
specifications outlined in Section 2.3.
e. Confirm that the crossover switch is in the correct position.
If a Link is not established, contact the Cabletron Systems the Global Call Center. Refer to Section 1.6 for details.
2E43-51/2E43-51R User’s Guide 3-13
Chapter 3: Installation

3.5.3 Connecting a Fiber Optic Segment to the FE-100FX and FE-100F3

The FE-100FX and FE-100F3 have SC style network ports. See
Figure 3-11. Cabletron Systems offers optional fiber optic cables that use
SC style connectors. The ST connectors are keyed to ensure proper crossover of the transmit and receive fibers.
NOTES
Fiber Optic Network Connection
An odd number of crossovers (preferably one) must be maintained between devices so that the transmit port of one device is connected to the receive port of the other device and vice versa.
If the fiber optic cable being used has SC style connectors that do not resemble MIC style connectors, or has SC connectors on one end and a different type on the other, such as ST connectors, ensure that the proper crossing over occurs.
1. Remove the protective plastic covers from the fiber optic ports on the
applicable port on the module and from the ends of the connectors.
The FE-100F3 uses Class 1 lasers. Do not use optical instruments to view the laser output. The use of optical
!
CAUTION
CAUTION
instruments to view laser output increases eye hazard. When viewing the output optical port, power must be removed from the network adapter.
Do not touch the ends of the fiber optic strands, and do not let the ends come in contact with dust, dirt, or other contaminants.
!
Contamination of the ends causes problems in data transmissions. If the ends become contaminated, blow the surfaces with a canned duster. A fiber port cleaning swap saturated with optical-grade isopropyl alcohol ma y also be used to clean the fiber optic ends.
2. Insert one end of the SC connector into the FE-100FX or FE-100F3
installed in the 2E43-51. See Figure 3-11.
3-14 2E43-51/2E43-51R User’s Guide
Connecting to the Network
3. At the other end of the fiber optic cable, attach the SC connector to the
other device.
6
5
RX LED
Figure 3-11 FE-100FX and FE-100F3 Ports
TX LED
2251-34
4. Verify that a Link exists by checking that the port RX LED is on
(flashing amber, blinking green, or solid green). If the RX LED is off and the TX LED is not blinking amber, perform the following steps until the RX LED is on:
a. Check that the po wer is turned on for the device at the other end of
the Link.
b. Verify proper crossover of fiber strands between the applicable
port on the 2E43-51 and the fiber optic device at the other end of the fiber optic link segment.
c. Verify that the fiber connection meets the dB loss specifications
outlined in Section 2.4.
If a Link has not been established, contact the Cabletron Systems Global Call Center. Refer to Section 1.6 for details.
2E43-51/2E43-51R User’s Guide 3-15
Chapter 3: Installation

3.6 COMPLETING THE INSTALLATION

After installing the 2E43-51 and any optional Fast Ethernet Interface Modules and HSIM as appropriate, and making the connections to the network, proceed as follows:
1. Secure the cables by running the cables along the strain-relief bracket
and tying them to the strain-relief bracket using cable ties.
2. The 2E43-51 is now ready to be set up through Local Management.
Refer to Chapter 5, Local Management, for information on how to access and use Local Management to configure the 2E43-51.
3-16 2E43-51/2E43-51R User’s Guide
CHAPTER 4

TROUBLESHOOTING

This chapter provides information concerning the following:
Using the LANVIEW diagnostic and status monitoring system
Troubleshooting network and 2E43-51 operational problems
Using the RESET button

4.1 USING LANVIEW

The 2E43-51 uses Cabletron Systems built-in visual diagnostic and status monitoring system called LANVIEW . The LANVIEW LEDs (Figure 4-1) allow quick observation of the network status to aid in diagnosing network problems. Refer to Table 4-1 for a description of the LEDs.
For a functional description of the LANVIEW LED on the optional Fast Ethernet Interface Module (FE-100TX), refer to Section 4.2.
All LEDs for the High Speed Interface Module (HSIM) are located on the HSIM and are described in the associated HSIM user’s guide.
ENET
RX TX
E3
E4
E1
E2
2E43-51
RESET
PWR
COM
PWR CPU
CPU
LINK 1
LINK 1
LINK
ENET 3
ENET 1
12
12
FE Module
HSIM-ASDP
6
TXRX
2251-36
Figure 4-1 LANVIEW LEDs
2E43-51/2E43-51R User’s Guide 4-1
Chapter 4: Troubleshooting
NOTE
tables indicate the following: Flashing indicates an LED pulse that is not flashing at a
random rate. Blinking indicates an LED pulse flashing at a steady rate (50%
on, 50% off).
Solid indicates a steady LED light. No pulsing.
Table 4-1 LANVIEW LEDs
LED Color State Recommended Action
The terms flashing, blinking, and solid used in the following
PWR Green Functional. Power
supply(ies) operating normally.
Amber This indication only
applies when there are two power supplies. Indicates loss of power supply redundancy.
CPU Off Power off. Power up device.
Red Blinking. Hardware
failure has occurred. Solid. Resetting,
normal power up reset.
Amber Blinking. Crippled. Contact the Cabletron
Solid. Testing. No action. Green Solid. Functional. No action. Amber
and Green
Booting. Blinks amber
and green while
booting.
No action.
1. Ensure that the power cords are plugged in correctly and that there is power at the power source.
2. Contact the Cabletron Systems Global Call Center.
Contact the Cabletron Systems Global Call Center.
No action.
Systems Global Call Center.
No action.
4-2 2E43-51/2E43-51R User’s Guide
Using LANVIEW
Table 4-1 LANVIEW LEDs (Continued)
LED Color State Recommended Action
RX (Receive) of ENET 1 – 4 and Ports 5 and 6
TX (Transmit) LED of ENET 1 – 4 and Ports 5 and 6
LINK Ports of ENET 1 – 4
Off No link. No activity.
Port enabled or disabled.
Green Blinking. Port
disabled.
Amber Flashing. Port
enabled, activity.
Red Diagnostic failure. Contact the Cabletron
Off Port enabled, and no
activity. Should flash green every two seconds indicating BPDUs being sent if STA is enabled and there is a valid link.
Green Flashing. Indicates
activity. Rate indicates data rate.
Amber Blinking. Port in
standby. Port may be disabled due to Spanning Tree.
Red Flashing. Indicates
collision rate. Solid. Diagnostic
failure.
Amber Solid. A link is
established with the device connected to the port.
Flashing. Link established, but administratively disabled.
Off. No link. No action.
No error.
No error.
No error.
Systems Global Call Center for assistance.
1. Ensure that the STA is enabled and that there is a valid link.
2. Contact the Cabletron Systems Global Call Center for assistance.
No action.
1. Ensure that the port is not disabled.
2. Contact the Cabletron Systems Global Call Center for assistance.
No action.
Contact the Cabletron Systems Global Call Center for assistance.
No action.
No action.
2E43-51/2E43-51R User’s Guide 4-3
Chapter 4: Troubleshooting

4.2 FE-100TX LED

The optional FE-100TX has one LED labeled 10/100. The 10/100 LED together with the RX LED allows the user to determine the Link status and the operating speed of the Fast Ethernet Interface Module. The 10/100 LED and the Receive (RX) LED are shown in Figure 4-2. Tables 4-2 and 4-3 provide a functional description of the 10/100 LED when the RX LED is on or off, respectively.
10
LED
100
=
x
Receive (RX) LED
Figure 4-2 FE-100TX LED
10
100
FE-100TX
56
22
2251-41
NOTE
Table 4-2 10/100 LED Indications When RX LED Is On
LED Color Indication
10/100 Off FE-100TX is operating at 10 Mbps.
Green FE-100TX is operating at 100 Mbps.
4-4 2E43-51/2E43-51R User’s Guide
A link exists if the associated port (5 or 6) RX LED is on.
FE-100TX LED
NOTE
No link exists if the associated port (5 or 6) RX LED is off.
Table 4-3 10/100 LED Indications When RX LED Is Off
LED Color Indication
10/100 Off No Link or no cable attached. FE-100TX
forced to 10 Mbps operation, or is manually set to “auto-negotiate” mode.
Green No Link or no cable attached. FE-100TX is
forced to 100 Mbps operation.
2E43-51/2E43-51R User’s Guide 4-5
Chapter 4: Troubleshooting

4.3 TROUBLESHOOTING CHECKLIST

If the 2E43-51 is not working properly, refer to Table 4-4 for a checklist of possible problems, causes, and recommended actions to resolve the problem.
Table 4-4 Troubleshooting Checklist
Problem Possible Cause Recommended Action
All LEDs are OFF. Loss of power. Check for proper connection
of the power cable and its access to a live outlet.
Installed improperly. Check the installation.
No Local Management Password screen.
Cannot contact the 2E43-51 from in-band management.
Port(s) goes into standby for no apparent reason.
User parameters (IP address, Device and Module name, etc.) were lost when the 2E43-51 power was cycled or the front panel RESET button was pressed.
Autobaud is enabled. Press ENTER (RETURN)
(may take up to four times).
Terminal setup is not correct.
Improper console cable used.
Using incorrect Community Name.
The 2E43-51 does not have an IP address assigned.
Port is disabled. Enable port. No link to device. Check link to device. The 2E43-51 detected a
loop condition.
Mode switch (7), NVRAM Reset, was changed sometime before either cycling power or pressing the RESET button causing the user-entered parameters to reset to factory default settings.
Refer to Chapter 5 for proper setup procedures.
Refer to Appendix A for proper console port pinouts.
Refer to Chapter 5 for Community Name setup.
Refer to Chapter 5 for IP address assignment procedure.
1. Review network design and delete unnecessary loops.
2. Call the Cabletron Systems Global Call Center if the problem continues.
1. Reenter the lost parameters as necessary.
2. Call the Cabletron Systems Global Call Center if the problem continues.
4-6 2E43-51/2E43-51R User’s Guide
Using the RESET Button

4.4 USING THE RESET BUTTON

The RESET button shown in Figure 4-3 resets the 2E43-51 processor without affecting the NVRAM.
Pressing the RESET button resets the device, and all current switching being performed by the device is halted. A network
!
CAUTION
downtime of up to two minutes will result from this action.
PWR
CPU
LINK 1
ENET 3
LINK 1
ENET 1
2251-37
2E43-51
E3
E4
E1
E2
RESET
RESET Button
COM
Figure 4-3 RESET Button
To reset the 2E43-51 processor, press and release the RESET button. The 2E43-51 goes through a reset process for approximately 45 seconds.
2E43-51/2E43-51R User’s Guide 4-7
Chapter 4: Troubleshooting
4-8 2E43-51/2E43-51R User’s Guide
CHAPTER 5

LOCAL MANAGEMENT

This chapter explains how to set up a management terminal to access Local Management. It also explains how to use the Local Management screens and commands.

5.1 OVERVIEW

Local Management for the 2E43-51 consists of a series of screens that allow the management of the 2E43-51 and its attached segments. The screens allow the user to do the following tasks:
Assign IP address and subnet mask
Select a default gateway
Control access by establishing community names
Download a new operation software image
Designate which Network Management Workstations receive SNMP
traps from the device
View statistics
Configure ports
Control the number of receive broadcasts that are switched out to the
other interfaces
Clear NVRAM
There are three ways to access Local Management:
Locally using a VT type terminal connected to the COM port
Remotely using a VT type terminal connected through a modem
In-band through a Telnet connection
2E43-51/2E43-51R User’s Guide 5-1
Chapter 5: Local Management

5.2 LOCAL MANAGEMENT KEYBOARD CONVENTIONS

All key names appear as capital letters in this manual. Table 5-1 explains the keyboard conventions and the key functions that are used.
Table 5-1 Keyboard Conventions
Key Function
These are selection keys that perform the same
ENTER Key RETURN Key
ESCAPE (ESC) Key
SPACE Bar BACKSPACE Key
Local Management function. For example, “Press ENTER” means that you can press either ENTER or RETURN, unless this manual specifically instructs you otherwise.
This key allows an escape from a Local Management screen without saving changes. For example, “Press ESC twice” means the ESC key must be pressed quickly two times.
These keys cycle through selections in some Local Management fields. Use the SPACE bar to cycle forward through selections and use BACKSPACE to cycle backward through selections.
These are navigation keys. Use the UP-ARROW, DOWN-ARROW, LEFT-ARROW, and
Arrow Keys
[–] Key
DEL Key
RIGHT-ARROW keys to move the screen cursor. For example , “Use the arrow keys” means to press whichever arrow key moves the cursor to the desired field on the Local Management screen.
This key decreases values from a Local Management increment field. For example, “Press [–]” means to press the minus sign key.
The DEL (Delete) key removes characters from a Local Management field. F or e xample, “Press DEL” means to press the Delete key.
5-2 2E43-51/2E43-51R User’s Guide
Management Terminal Setup

5.3 MANA GEMENT TERMINAL SETUP

Use one of the following systems to access Local Management:
An IBM or compatible PC running a VT series emulation software
package
A Digital Equipment Corporation VT100 type terminal
A VT type terminal running emulation programs for the Digital
Equipment Corporation VT100 series
A remote VT100 type terminal via a modem connection
In-band via a Telnet connection
2E43-51/2E43-51R User’s Guide 5-3
Chapter 5: Local Management

5.3.1 Console Cable Connection

Use the Console Cable Kit provided with the 2E43-51 to attach the management terminal to the 2E43-51 COM port as shown in Figure 5-1.
Connect an IBM PC or compatible device, running the VT terminal emulation, to the 2E43-51 as follows:
1. Connect the RJ45 connector at one end of the cable (supplied in the
kit) to the COM port on the 2E43-51.
2. Plug the RJ45 connector at the other end of the cable into the
RJ45-to-DB9 adapter (supplied in the kit).
3. Connect the RJ45-to-DB9 adapter to the communications port on
the PC.
12
2E43-51
E3E1E4
E2
RESET
COM
ENET 3 ENET 4
LINK 1
PWR CPU
ENET 1
LINK 1LINK 1
12
LINK 1
RJ45 COM Port
ENET 2
12
12
65
UTP Cable
with RJ45 Connectors
PC
RJ45-to-DB9
PC Adapter
2251-50
Figure 5-1 Management Terminal Connection
5-4 2E43-51/2E43-51R User’s Guide
Management Terminal Setup

5.3.2 Management Terminal Setup Parameters

Table 5-2 lists the setup parameters for the local management terminal.
Table 5-2 VT Terminal Setup
Display Setup Menu
Columns -> Controls -> Auto Wrap -> Scroll -> Text Cursor -> Cursor Style ->
General Setup Menu
Mode -> ID number -> Cursor Keys -> Power Supply ->
Communications Setup Menu
Transmit -> Receive -> XOFF -> Bits -> Parity -> Stop Bit -> Local Echo -> Port -> Transmit -> Auto Answerback ->
Keyboard Setup Menu
Keys -> Auto Repeat -> Keyclick -> Margin Bell -> Warning Bell ->
80 Columns Interpret Controls No Auto Wrap Jump Scroll Cursor Underline Cursor Style
VT100, 7 Bit Controls VT100ID Normal Cursor Keys UPSS DEC Supplemental
2400, 4800, 9600, 19200 Receive=Transmit XOFF at 64 8 bits No Parity 1 Stop Bit No Local Echo DEC-423, Data Leads Only Limited T r ansmit No Auto Answerback
Typewriter Keys any option any option Margin Bell Warning Bell
2E43-51/2E43-51R User’s Guide 5-5
Chapter 5: Local Management

5.3.3 Telnet Connections

Once the 2E43-51 has a valid IP address, the user can establish a Telnet session with Local Management from any TCP/IP based node on the network. Telnet connections to the 2E43-51 require the community name passwords assigned at the SNMP Community Names screen of the 2E43-51.
For information about setting the IP address, refer to Section 5.7. For information about assigning community names, refer to Section 5.8. Refer to the instructions included with the Telnet application for
information about establishing a Telnet session.
5-6 2E43-51/2E43-51R User’s Guide
Management Terminal Setup

5.3.4 Monitoring an Uninterruptible Power Supply

If the 2E43-51 is connected to an Uninterruptible Power Supply (UPS) device for protection against the loss of power, a connection from the 2E43-51 COM port to the UPS can be made to monitor the power status of the UPS. To use the COM port for this purpose, it must be reconfigured to support the UPS connection using the procedure described in
Section 5.7.10. Refer to the UPS documentation for details on how to
access the status information. The Console Cable Kit provided with the 2E43-51 is used to attach the
UPS to the 2E43-51 COM port as shown in Figure 5-2. To connect the UPS device to the COM port of the 2E43-51, proceed as
follows:
1. Connect the RJ45 connector at one end of the cable to the COM port
on the 2E43-51.
2. Plug the RJ45 connector at the other end of the cable into the
RJ45-to-DB9 male (UPS) adapter.
3. Connect the RJ45-to-DB9 male (UPS) adapter to the female DB9 port
on the rear of the UPS device (see the particular UPS device’s user instructions for more specific information about the monitoring connection).
12
2E43-51
E3E1E4
E2
RESET
COM
ENET 3 ENET 4
LINK 1
PWR CPU
ENET 1
LINK 1LINK 1
12
LINK 1
ENET 2
12
12
65
DB9 Port
RJ45 COM Port
UTP Cable
with RJ45 Connectors
UPS Device
RJ45-to-DB9 UPS Adapter
2251-51
Figure 5-2 Uninterruptible Power Supply (UPS) Connection
2E43-51/2E43-51R User’s Guide 5-7
Chapter 5: Local Management

5.4 ACCESSING LOCAL MANAGEMENT

Access to Local Management is controlled through the Local Management Password screen Figure 5-3. Whenever a connection is made to the 2E43-51 the Local Management Password screen displays. Before continuing, the user must enter a password (community name) which is compared to the previously stored passwords. The le vel of access allowed the user depends on the password. To set or change passwords, refer to Section 5.8. The following steps describe the procedure to access Local Management.
1. Turn on the terminal. Press ENTER (up to four times) until the
2E43-51 Local Management Password screen displays. It is the automatic line speed seeking feature of the port that makes it necessary at times to press ENTER several times.
Event Message Line
2E43-51 LOCAL MANAGEMENT
CABLETRON Systems, Incorporated
P.O.Box 5005
Rochester, NH 03866-5005 USA
(603) 332-9400
(c) Copyright CABLETRON Systems, Inc, 1997
Device Serial Number: XXXXXXXXX Device Hardware Revision: XX Device Firmware Revision: X.XX.XX Device BOOTPROM Revision: X.XX.XX
Enter Password:
22511-12
Figure 5-3 The 2E43-51 Local Management Password Screen
2. Enter the Password and press ENTER. The default super-user access
password is “public” or press ENTER.
5-8 2E43-51/2E43-51R User’s Guide
Accessing Local Management
NOTE
The User’s password is one of the community names specified in the SNMP Community Names screen. Access to certain Local Management capabilities depends on the degree of access accorded that community name. Refer to Section 5.8.
If an invalid password is entered, the terminal beeps and the cursor returns to the beginning of the password entry field.
Entering a valid password causes the associated access level to display at the bottom of the screen and the Device Menu screen to appear.
If no activity occurs for sev eral min utes, the Local Management Password screen redisplays and the password has to be reentered.

5.4.1 Navigating Local Management Screens

The 2E4X-27 Local Management application consists of a series of menu screens. Navigate through Local Management by selecting items from the menu screens.
The 2E43-51 supports three modes of switch operation. The switching modes are as follows:
802.1D Switching (traditional switching)
802.1Q Switching (port based VLAN switching)
SecureFast VLAN (Cabletron Systems SecureFast switching)
Depending on the Operational Mode set for the device, the hierarchy of the Local Management screens differs as shown in Figure 5-4, Figure 5-5 and Figure 5-6. Refer to the appropriate figure that relates to the Operational Mode set for the device to see the applicable Local Management screen hierarchy.
2E43-51/2E43-51R User’s Guide 5-9
Chapter 5: Local Management
\
Password
Password
Device Menu
Device Configuration Menu
Device Statistics Menu
Network Tools
General Configuration SNMP Community Names
SNMP Traps Switch Configuration
SmartTrunk Configuration
Device Specific Configuration Menu
Switch Statistics Interface Statistics RMON Statistics Repeater Statistics
System Resources
High Speed Interface Configuration
Flash Download Port Redirect
Function Broadcast
Suppression Repeater
Configuration Menu
Figure 5-4 802.1D Switching Mode, LM Screen Hierarchy
Device Menu
Device Configuration Menu
Device Statistics Menu
Network Tools
General Configuration SNMP Community Names SNMP Traps
Switch Configuration SmartTrunk
Configuration
Device Specific Configuration Menu
Switch Statistics Interface Statistics RMON Statistics Repeater Statistics
System Resources
High Speed Interface Configuration
Flash Download
Broadcast Suppression
802.1Q VLAN Configuration
Repeater Configuration Menu
Fast Ethernet Interfaces
HSIM
Device Level Security Configuration
Port Level Security Configuration
22514-43
Fast Ethernet Interfaces
HSIM
Device Level Security Configuration
Port Level Security Configuration
22511-82
Figure 5-5 802.1Q Switching Mode, LM Screen Hierarchy
5-10 2E43-51/2E43-51R User’s Guide
Accessing Local Management
Password
Device Menu
Device Configuration Menu
Device Statistics Menu
Network Tools
General Configuration SNMP Community Names SNMP Traps
Device Specific Configuration Menu
Interface Statistics RMON Statistics Repeater Statistics
System Resources
High Speed Interface Configuration
Flash Download Repeater
Configuration Menu
Fast Ethernet Interfaces
HSIM
Device Level Security Configuration
Port Level Security Configuration
22511-83
Figure 5-6 SecureFast VLAN Mode, LM Screen Hierarchy

5.4.2 Selecting Local Management Menu Screen Items

Select items on a menu screen by performing the following steps:
1. Use the arrow keys to highlight a menu item.
2. Press ENTER. The selected menu item displays on the screen.

5.4.3 Exiting Local Management Screens

There are two ways to exit the Local Management (LM) screens.
Using the Exit Command
To exit LM using the EXIT screen command, proceed as follows:
1. Use the arrow keys to highlight the EXIT command at the bottom of
the Local Management screen.
2. Press ENTER. The Local Management Password screen displays and
the session ends.
Using the RETURN Command
To exit LM using the RETURN command, proceed as follows:
1. Use the arrow keys to highlight the RETURN command at the bottom
of the Local Management screen.
2E43-51/2E43-51R User’s Guide 5-11
Chapter 5: Local Management
2. Press ENTER. The previous screen in the Local Management
hierarchy displays.
NOTE
The user can also exit Local Management screens by pressing ESC twice. This exit method does not warn about unsaved changes and all unsaved changes are lost.
3. Exit from 2E43-51 Local Management by repeating steps 1 and 2 until
the Device Menu screen displays.
4. To end the LM session, use the arrow keys to highlight the RETURN
command at the bottom of the Device Menu screen.
5. Press ENTER. The Local Management Password screen displays and
the session ends.
5-12 2E43-51/2E43-51R User’s Guide
Device Menu Screen

5.5 DEVICE MENU SCREEN

The Device Menu screen is the access point for all Local Management screens. Figure 5-7 shows the Device Menu screen.
Event Message Line
Device Name: 2E43-51
NOTE
2E43-51 LOCAL MANAGEMENT
Device Menu
Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.XX
DEVICE CONFIGURATION
DEVICE STATISTICS NETWORK TOOLS
EXIT
RETURN
2251_13
Figure 5-7 Device Menu Screen
If the terminal is idle for several minutes, the Local Management Password screen redisplays and the session ends.
2E43-51/2E43-51R User’s Guide 5-13
Chapter 5: Local Management
The following explains each Device Menu screen field as shown in
Figure 5-7:
DEVICE CONFIGURATION
The Device Configuration screen provides access to the Local Management screens that are used to configure the 2E43-51 and also to the Device Specific Configuration Menu screen. The Device Specific Configuration Menu screen provides access to the screens that allow the user to check the 2E43-51 resources and set operating parameters specific to each port.
For details about the Device Configuration Menu screen, refer to
Section 5.6. For details about the Device Specific Configuration Menu
screen, refer to Section 5.11.
DEVICE STATISTICS
The Device Statistics screen provides statistics and performance information for the 2E43-51. For details, refer to Section 5.21.
NETWORK TOOLS
The Network Tools function resides on the 2E43-51 and consists of a series of commands that allow the user to access and manage network devices. Section 5.26 explains how to use the Network Tools utility.
5-14 2E43-51/2E43-51R User’s Guide
Device Configuration Menu Screen

5.6 DEVICE CONFIGURATION MENU SCREEN

The Device Configuration Menu screen, Figure 5-8, provides access to Local Management screens. These screens allow the user to configure and monitor operating parameters, modify SNMP community names, set SNMP traps, configure switch parameters and configure 2E43-51 ports.
NOTE
screen do not display if the operational mode of the device is set to SECURE FAST VLAN:
SWITCH CONFIGURATION SMARTTRUNK CONFIGURATION
Section 5.7.9 provides instructions on setting the operational
mode.
To access the Device Configuration Menu screen from the Device Menu screen, use the arrow keys to highlight the DEVICE CONFIGURATION menu item and press ENTER. The Device Configuration Menu screen displays.
2E43-51 LOCAL MANAGEMENT
Device Configuration Menu
The following menu items on the Device Configuration Menu
Device Name: 2E43-51
GENERAL CONFIGURATION
SNMP COMMUNITY NAMES SNMP TRAPS SWITCH CONFIGURATION SMARTTRUNK CONFIGURATION DEVICE SPECIFIC CONFIGURATION
Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.XX
EXIT
RETURN
22511_66
Figure 5-8 Device Configuration Menu Screen
2E43-51/2E43-51R User’s Guide 5-15
Chapter 5: Local Management
The following briefly explains each screen accessible from the Device Configuration Menu screen:
GENERAL CONFIGURATION
The General Configuration screen allows the user to monitor and configure operating parameters for the 2E43-51. For details, refer to Section 5.7.
SNMP COMMUNITY NAMES
The SNMP Community Names screen allows the user to enter new, change, or review the community names used as access passwords for device management operation. Access is limited based on the password level of the user. For details, refer to Section 5.8.
SNMP TRAPS
The SNMP Traps screen provides display and configuration access to the table of IP addresses used for trap destinations and associated community names. For details, refer to Section 5.9.
SWITCH CONFIGURATION
The Switch Configuration screen provides the basic setup options for making a switch operational in the network. For details, refer to
Section 5.10.
SMARTTRUNK CONFIGURATION
The SmartTrunk Configuration screen allows the user to logically group interfaces to aggregate high speed uplinks. For details, refer to the SmartTrunk User’s Guide.
DEVICE SPECIFIC CONFIGURATION
The Device Specific Configuration Menu screen allows the user to select screens to configure ports or check system resources specific to the 2E43-51. For details, refer to Section 5.11.
5-16 2E43-51/2E43-51R User’s Guide
General Configuration Screen

5.7 GENERAL CONFIGURATION SCREEN

The General Configuration screen, Figure 5-9, allows the user to set the system date and time, IP address and subnet mask, the Default Gateway, the TFTP Gateway IP address, and the operational mode. Also, clear the NVRAM, set the screen refresh time, the screen lockout time, the IP fragmentation, and the COM port configuration.
To access the General Configuration screen from the Device Configuration Menu screen, use the arrow keys to highlight the GENERAL CONFIGURATION menu item and press ENTER. The General Configuration screen displays.
Event Message Line
Device Name: 2E43-51
MAC Address: IP Address: Subnet Mask: Default Gateway: TFTP Gateway IP Addr:
Operational Mode: [Switching]
Com: [ENABLED] Application: [LM] Clear NVRAM: [NO] IP Fragmentation [ENABLED ]
2E43-51 LOCAL MANAGEMENT
General Configuration
00-00-ID-00-00-00
0.0.0.0
0.0.0.0 NONE DEFINED
0.0.0.0
EXIT
Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.XX
Device Date: Device Time: Screen Refresh Time: Screen Lockout Time: Device Uptime: XX D XX H XX M
01/11/1997 14:23:00 03 sec. 15 min.
RETURNSAVE
2251-15
Figure 5-9 General Configuration Screen
The following briefly explains each General Configuration screen field:
MAC Address (Read-Only)
Displays the physical address of the 2E43-51.
2E43-51/2E43-51R User’s Guide 5-17
Chapter 5: Local Management
IP Address (Modifiable)
Displays and allows the user to set the IP address for the 2E43-51. To set the IP address, refer to Section 5.7.1. The IP address can also be set through Runtime IP Address Discovery as previously described in
Section 1.3.5.
Subnet Mask (Modifiable)
Displays the subnet mask for the 2E43-51. A subnet mask “masks out” the network bits of the IP address by setting the bits in the mask to 1 when the network treats the corresponding bits in the IP address as part of the network or subnetwork address, or to 0 if the corresponding bit identifies the host. For details about how to change the subnet mask from its default value, refer to Section 5.7.2.
Default Gateway (Modifiable)
Displays the default gateway for the 2E43-51. This field is not defined until an appropriate value is entered. For details about why and ho w to set the Default Gateway, refer to Section 5.7.3.
TFTP Gateway IP Addr (Modifiable)
Displays and allows the user to set the TFTP Gateway IP address for the 2E43-51. To set the TFTP Gateway IP address, refer to Section 5.7.4.
Device Date (Modifiable)
Contains a value that the device recognizes as the current date. To set a new device date, refer to Section 5.7.5.
Device Time (Modifiable)
Contains a value that the device recognizes as the current time. To enter a new time, refer to Section 5.7.6.
Screen Refresh Time (Modifiable)
Contains the rate at which the screens are updated. This setting determines how frequently (in seconds) information is updated on the screen. To enter a new update time, refer to Section 5.7.7.
5-18 2E43-51/2E43-51R User’s Guide
General Configuration Screen
Screen Lockout Time (Modifiable)
Contains the maximum number of minutes that the Local Management application displays a module’s screen while awaiting input or action from a user. For example, if the number 5 is entered in this field, the user has up to five minutes to respond to each of the specified module’s Local Management screens.
In this example, after five minutes of “idleness” (no input or action), the terminal “beeps” five times, the Local Management application terminates the session, and the display returns to the Local Management Password screen. To enter a new lockout time, refer to Section 5.7.8.
Device Uptime (Read-Only)
Displays the total time that the device has been operating.
Operational Mode (Selectable)
Allows the user to set the 2E43-51 so it operates as a an 802.1D switch (802.1D SWITCHING), an IEEE 802.1Q switch (802.1Q SWITCHING), or a Cabletron Systems SecureFast switch (SECURE FAST VLAN).
In 802.1D SWITCHING mode, the 12 connections on each RJ21 port (ENET1 – ENET4) act as repeaters, and may be switched to each other and to any Fast Ethernet Interface Module and HSIM port(s) in the 2E43-51R.
In 802.1Q SWITCHING mode, the device is able to increase its switching functionality by creating and maintaining IEEE 802.1Q port based Virtual LANs (VLANs).
When the operational mode is set to SECURE FAST VLAN, the device acts as a SecureFast switch. With the Cabletron Systems VLAN Manager software, the device is able to increase its switching functionality by creating and maintaining VLANs.
For details on how to select the Operational Mode, refer to Section 5.7.9.
Com (Toggle)
Allows the user to enable or disable the COM port. The selection toggles between ENABLED and DISABLED. The default is ENABLED. For details about setting up the COM port, refer to Section 5.7.10.
2E43-51/2E43-51R User’s Guide 5-19
Chapter 5: Local Management
Application (Toggle)
Allows the user to set the application that the COM port supports. The field toggles between LM (Local Management) and UPS (Uninterruptible Power Supply).
The UPS setting allows the COM port to be used to monitor an American Power Conversion (APC) Uninterruptible Power Supply (UPS).
The baud rate setting for LM is automatically sensed. For UPS, the baud rate is automatically set to 2400.
The default setting is LM. For details about how to configure the COM port for various applications, refer to Section 5.7.10.
Clear NVRAM (Toggle)
Allows the user to reset NVRAM to the factory default settings. All user-entered parameters, such as IP address and Community Names, are then replaced with 2E43-51 default configuration settings. For details, refer to Section 5.7.11.
IP Fragmentation (Toggle)
Allows the user to enable or disable IP Fragmentation. The default setting for this is field is ENABLED. If the 2E43-51 is to be bridged to an FDDI ring, IP Fragmentation must be enabled. If IP Fragmentation is disabled, all FDDI frames that exceed the maximum Ethernet frame size are discarded. For details on enabling IP Fragmentation, refer to
Section 5.7.12.

5.7.1 Setting the IP Address

To set the IP address, perform the following steps:
1. Use the arrow keys to highlight the IP Address field.
2. Enter the IP address into this field using Dotted Decimal Notation
(DDN) format. For example: 134.141.79.120
3. Press ENTER. If the IP address is a valid format, the cursor returns to
the beginning of the IP address field. If the entry is not valid, the screen displays the message “INVALID IP ADDRESS OR FORMAT ENTERED”. Local Management does not alter the current value and refreshes the IP address field with the previous value.
5-20 2E43-51/2E43-51R User’s Guide
General Configuration Screen
4. Use the arrow keys to highlight the SAVE command, then press
ENTER. The warning screen shown in Figure 5-10 displays.
WARNING!
YOU HAVE ELECTED TO SAVE ONE OR MORE CONFIGURATION ITEMS THAT REQUIRE RESETTING THIS MODULE.
ARE YOU SURE YOU WANT TO CONTINUE?
YES
Figure 5-10 Configuration Warning Screen
NO
19601-84
5. Use the arrow keys to highlight the YES command, then press
ENTER. The changes are saved and the device reboots.

5.7.2 Setting the Subnet Mask

If the management workstation that is to receive SNMP traps from the 2E43-51 is located on a separate subnet, the subnet mask for the 2E43-51 may need to be changed from its default.
To change the subnet mask from its default, perform the following steps:
1. Use the arrow keys to highlight the Subnet Mask field.
2. Enter the subnet mask into this field using Dotted Decimal Notation
(DDN) format. For example: 255.255.0.0
2E43-51/2E43-51R User’s Guide 5-21
Chapter 5: Local Management
3. Press ENTER. If the subnet mask is valid, the cursor returns to the
beginning of the Subnet Mask field. If the entry is not valid, the screen displays the message “INVALID SUBNET MASK OR FORMAT ENTERED”. Local Management does not alter the current value, but it does refresh the Subnet Mask field with the previous value.
4. Use the arrow keys to highlight the SAVE command, then press
ENTER. The warning screen shown in Figure 5-11 displays.
WARNING!
YOU HAVE ELECTED TO SAVE ONE OR MORE CONFIGURATION ITEMS THAT REQUIRE RESETTING THIS MODULE.
ARE YOU SURE YOU WANT TO CONTINUE?
YES
Figure 5-11 Configuration Warning Screen
NO
19601-84
5. Use the arrow key to highlight the YES command, then press ENTER.
The changes are saved and the device reboots.

5.7.3 Setting the Default Gateway

If the SNMP management station is located on a different IP subnet than the 2E43-51, a default gateway must be specified. When an SNMP Trap is generated, the 2E43-51 sends the Trap to the default gateway. To set the default gateway, perform the following steps:
1. Use the arrow keys to highlight the Default Gateway field.
5-22 2E43-51/2E43-51R User’s Guide
General Configuration Screen
2. Enter the IP address of the default gateway using the DDN format.
For example: 134.141.79.121
3. Press ENTER. If the default gateway entered is a valid format, the
cursor returns to the beginning of the Default Gateway field. If the entry is not valid, the screen displays “INVALID DEFAULT GATEWAY OR FORMAT ENTERED”. Local Management does not alter the current value, but it does refresh the Default Gateway field with the previous value.
4. Use the arrow keys to highlight the SAVE command.
5. Press ENTER. The message “SAVED OK” displays at the top of the
screen.

5.7.4 Setting the TFTP Gateway IP Address

If the network TFTP server is located on a different IP subnet than the 2E43-51, a Gateway IP address should be specified. To set the TFTP Gateway IP address, perform the following steps:
1. Use the arrow keys to highlight the TFTP Gateway IP Addr field.
2. Enter the IP address of the TFTP gateway using the DDN format.
For example: 134.141.80.122
3. Press ENTER. If the TFTP gateway IP address entered is a valid
format, the cursor returns to the beginning of the TFTP Gateway IP Address field. If the entry is not valid, the screen displays “INVALID TFTP GATEWAY IP ADDRESS OR FORMAT ENTERED”. Local Management does not alter the current value, but it does refresh the TFTP Gateway IP Address field with the previous value.
4. Use the arrow keys to highlight the SAVE command.
5. Press ENTER. The message “SAVED OK” displays at the top of the
screen.
2E43-51/2E43-51R User’s Guide 5-23
Chapter 5: Local Management

5.7.5 Setting the Device Date

The 2E43-51 is year 2000 compliant so that the Device Date field can be set beyond the year 1999.
To set the system date, perform the following steps:
1. Use the arrow keys to highlight the Device Date field.
2. Enter the date in an MM/DD/YYYY format.
NOTE
It is not necessary to add separators between month, day, and year numbers, as long as each entry has the correct number of numeric characters. For example, to set the date to 03/17/1997, type “03171997” in the Device Date field.
3. Press ENTER to set the system calendar to the date in the input field.
4. Use the arrow keys to highlight the SAVE command at the bottom of
the screen and press ENTER.
If the date entered is a valid format, the message displays “SAVED OK” at the top of the screen. If the entry is not valid, Local Management does not alter the current value, but it does refresh the Device Date field with the previous value.

5.7.6 Setting the Device Time

To set the device clock, perform the following steps:
1. Use the arrow keys to highlight the Device Time field.
2. Enter the time in a 24-hour format, HH:MM:SS.
NOTE
When entering the time in the system time field, separators between hours, minutes, and seconds are not needed as long as each entry uses two numeric characters. F or e xample, to set the time to 6:45 A.M., type “064500” in the Device Time field.
3. Press ENTER to set the system clock to the time in the input field.
4. Use the arrow keys to highlight the SAVE command at the bottom of
the screen and press ENTER.
5-24 2E43-51/2E43-51R User’s Guide
General Configuration Screen
If the time entered is a valid format, the message displays “SAVED OK” at the top of the screen. If the entry is not valid, Local Management does not alter the current value and refreshes the Device Time field with the previous value.

5.7.7 Entering a New Screen Refresh Time

The screen refresh time is set from 3 to 99 seconds with a default of 3 seconds. To set a new screen refresh time, perform the following steps:
1. Use the arrow keys to highlight the Screen Refresh Time field.
2. Enter a number from 3 to 99.
3. Press ENTER to set the refresh time to the time entered in the input
field.
4. Use the arrow keys to highlight the SAVE command at the bottom of
the screen and press ENTER.
If the time entered is within the 3 to 99 seconds range, the message “SAVED OK” displays at the top of the screen. If the entry is not valid, Local Management does not alter the current setting, but it does refresh the Screen Refresh Time field with the previous value.

5.7.8 Setting the Screen Lockout Time

The screen lockout time can be set from 1 to 30 minutes with a default of 15 minutes. To set a new lockout time, perform the following steps:
1. Use the arrow keys to highlight the Screen Lockout Time field.
2. Enter a number from 1 to 30.
3. Press ENTER to set the lockout time in the input field.
4. Use the arrow keys to highlight the SAVE command at the bottom of
the screen and press ENTER.
If the time entered is within the 1 to 30 minutes range, the message “SAVED OK” displays at the top of the screen. If the entry is not valid, Local Management does not alter the current setting, but it does refresh the Screen Lockout Time field with the previous value.
2E43-51/2E43-51R User’s Guide 5-25
Chapter 5: Local Management

5.7.9 Setting the Operational Mode

To set the Operational Mode, proceed as follows:
1. Use the arrow keys to highlight the Operational Mode field.
2. Press the SPACE bar to toggle to the appropriate operational mode
(802.1D SWITCHING, 802.1Q SWITCHING or SECURE FAST VLAN).
3. Use the arrow keys to highlight the SAVE command, then press
ENTER. The warning screen shown in Figure 5-12 displays.
WARNING!
YOU HAVE ELECTED TO SAVE ONE OR MORE CONFIGURATION ITEMS THAT REQUIRE RESETTING THIS MODULE.
ARE YOU SURE YOU WANT TO CONTINUE?
YES
Figure 5-12 Configuration Warning Screen
NO
19601-84
4. Use the arrow keys to highlight the YES command, then press
ENTER. The changes are saved and the device reboots.
NOTE
5-26 2E43-51/2E43-51R User’s Guide
If the 2E43-51 is set to 802.1Q SWITCHING, refer to your
Port Based VLAN User’s Guide
type of operation. If the 2E43-51 is set to SECURE FAST VLAN, refer to your
SecureFast documentation set to configure the devices for this type of operation.
to configure the devices for this
General Configuration Screen
5.7.10 Configuring the COM Port
Upon power up, the COM port is configured to the default settings of ENABLED and LM.
Before altering the COM port settings, read this entire COM port configuration section. Altering the COM port settings
!
CAUTION
To configure the COM port, the user must enable/disable the COM port and select an application.
The 2E43-51 COM port supports the following applications:
Local Management connections
American Power Conversion Uninterruptible Power Supply (UPS)
To configure the COM port, proceed as follows:
1. Use the arrow keys to highlight the Com field.
disconnects the Local Management terminal from the port, and ends the Local Management session.
connections
Do NOT disable or alter the settings of the COM port while operating the current Local Management connection through a
!
CAUTION
terminal. Altering the COM port settings disconnects the Local Management terminal from the port, and ends the Local Management session. If the 2E43-51 was previously assigned a valid IP address, reenter Local Management by establishing a Telnet connection to the device. If the device does not have a valid IP address and the COM port has been disabled or the settings changed, reset NVRAM on the 2E43-51 (refer to
Section 5.7.11) to reestablish COM port communications.
2. Press the SPACE bar to choose either ENABLED or DISABLED.
ENABLED supports the connection of a terminal to the COM port for
a particular application. DISABLED does not support the connection of a terminal to the COM port.
2E43-51/2E43-51R User’s Guide 5-27
Chapter 5: Local Management
If the COM port is reconfigured without a valid IP address set on the device, the message shown in Figure 5-13 displays.
!
CAUTION
Do not continue unless the outcome of the action is fully understood.
WARNING
THE COM PORT HAS BEEN RECONFIGURED AND THERE IS NO IP ADDRESS SET FOR THIS DEVICE. YOU WILL NO LONGER BE ABLE TO MANAGE THIS BOARD. DO YOU STILL WISH TO RECONFIGURE THIS COM PORT?
YES
Figure 5-13 COM Port Warning Screen
NO
174252
3. Use the arrow keys to highlight YES. Press ENTER.
4. If you ENABLED the port, proceed to step 5. If you DISABLED the
port, use the arrow keys to highlight SAVE at the bottom of the screen, then press ENTER.
5. When the message “SAVED OK” appears, the edits you made are
saved.
Exiting without saving causes the message “NOT SAVED -­PRESS SA VE TO KEEP CHANGES” to appear. Exiting without
!
CAUTION
saving causes all edits to be lost.
6. Use the arrows keys to highlight the Application field.
5-28 2E43-51/2E43-51R User’s Guide
General Configuration Screen
7. Use the SPACE bar or BACKSPACE to step through the available
settings until the operation you require appears. Table 5-3 lists the available settings and their corresponding applications.
Table 5-3 COM Port Application Settings
Setting Application
[LM] Local Management Session [UPS] APC Power Supply SNMP Proxy
8. Press ENTER to accept the application.
9. Use the arrow keys to highlight the SAVE command at the bottom of
the screen, then press the ENTER key.
10. When the message “SAVED OK” displays, the edits are saved.

5.7.11 Clearing NVRAM

Clearing NVRAM will result in the loss of all user-entered parameters. Do not proceed unless this procedure is
!
CAUTION
completely understood.
Clearing NVRAM allows the user to clear all user-entered parameters, such as, the IP address and Community Names from NVRAM.
Clear NVRAM as follows:
1. Use the arrow keys to highlight the Clear NVRAM field.
2. Use the SPACE bar to toggle the field to YES.
3. Use the arrow keys to highlight SAVE at the bottom of the screen.
4. Press ENTER. The warning screen shown in Figure 5-14 displays.
2E43-51/2E43-51R User’s Guide 5-29
Chapter 5: Local Management
YOU HAVE ELECTED TO CLEAR NVRAM. THIS WILL CLEAR ALL SYSTEM DEFAULTS INCLUDING BUT NOT LIMITED TO IP ADDRESS, INTERFACE CONFIGURATION, AND COM PORT CONFIGURATION, THEN RESET THE BOARD. ARE YOU SURE YOU WANT TO CLEAR NVRAM?
WARNING
YES
Figure 5-14 Clear NVRAM Warning Screen
NO
174251
5. Select YES and the message “CLEARING NVRAM. REBOOT IN
PROGRESS...” displays.
6. The 2E43-51 clears NVRAM and reboots. All user-entered parameters
default to factory default settings.

5.7.12 Enabling/Disabling IP Fragmentation

To enable or disable IP Fragmentation, proceed as follows:
If the 2E43-51 is being bridged to an FDDI ring (for example, via an optional HSIM-F6), enable IP Fragmentation. If it is
!
CAUTION
1. Use the arrow keys to highlight the IP Fragmentation field.
2. Press the SPACE bar to choose either ENABLED or DISABLED.
disabled, all FDDI frames that exceed the maximum Ethernet frame size are discarded.
3. Use the arrow keys to highlight the SAVE command.
4. Press ENTER. The message “SAVED OK” displays at the top of the
screen.
5-30 2E43-51/2E43-51R User’s Guide
SNMP Community Names Screen

5.8 SNMP COMMUNITY NAMES SCREEN

The SNMP Community Names screen allows the user to set SNMP Management community names. Community names act as passwords to Local/Remote Management and are agents of security access to the 2E43-51. Access to the 2E43-51 is controlled by enacting any of three different levels of security authorization (read-only, read-write, and super-user).
NOTE
allows existing passwords to be changed, and all modifiable MIB objects for the Cabletron Container MIB and Internet MIB-II to be edited.
To access the SNMP Community Names screen from the Device Configuration Menu screen, use the arrow keys to highlight the SNMP COMMUNITY NAMES menu item and press ENTER. The SNMP Community Names screen displays.
Super-user access gives the user full management privileges,
Event Message Line
Device Name: 2E43-51
2E43-51 LOCAL MANAGEMENT
SNMP Community Names
Community Name
public
public public
Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.XX
Access Policy read-only read-write super-user
EXIT
RETURNSAVE
2251-16
Figure 5-15 SNMP Community Names Screen
2E43-51/2E43-51R User’s Guide 5-31
Chapter 5: Local Management
The following explains each SNMP Community Names screen field:
Community Name (Modifiable)
Displays the user-defined name through which a user accesses the 2E43-51 SNMP Management. Any community name assigned here acts as a password to Local/Remote Management.
Access Policy (Read-Only)
Indicates the access accorded each community name. The available access levels are as follows:
read-only This community name gives the user read-only
access to the 2E43-51 MIB objects, and excludes access to security-protected fields of read-write or super-user authorization.
read-write This community name gives the user read-write
access to the 2E43-51 MIB objects, excluding security protected fields for Super-User access only.
super-user This community name gi ves the user read-write
access to the 2E43-51
MIB objects and allows
the user to change all modifiable parameters including community names, IP addresses, traps, and SNMP objects.

5.8.1 Establishing Community Names

The password used to access Local Management at the Password Screen must have super-user access to view and edit the SNMP Community Names screen. Using a password with read-only or read-write access does not allow the user to view or edit the SNMP Community Names screen.
NOTE
5-32 2E43-51/2E43-51R User’s Guide
Any community name assigned in the SNMP Community Names screen is a password to its corresponding level of access to Local Management. The community name assigned super-user access is the only one that gives the user complete access to Local Management.
SNMP Community Names Screen
To establish community names, proceed as follows:
1. Use the arrow keys to highlight the Community Name field adjacent
to the selected access level.
2. Enter the password in the field (maximum 31 characters).
3. Press ENTER.
4. Repeat steps 1 through 3 to modify the other community names.
5. Use the arrow keys to highlight the SAVE command at the bottom of
the screen and press ENTER. The message “SAVED OK” displays. The community names are saved to memory and their access modes implemented.
NOTE
Exiting without saving causes a “NOT SAVED?” message to display abov e the SAVE command. Edits are lost if the y are not saved before exiting.
6. To exit the screen, use the arrow keys to highlight RETURN and press
ENTER.
2E43-51/2E43-51R User’s Guide 5-33
Chapter 5: Local Management

5.9 SNMP TRAPS SCREEN

Since the 2E43-51 is an SNMP compliant device, it can send messages to multiple Network Management Stations to alert users of status changes. The SNMP Traps screen is shown in Figure 5-16.
To access the SNMP Traps screen from the Device Configuration Menu screen, use the arrow keys to highlight the SNMP TRAPS menu item and press ENTER. The SNMP Traps screen displays.
Event Message Line
Device Name: 2E43-51
Trap Destination
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
2E43-51 LOCAL MANAGEMENT
SNMP Traps
Trap Community Name
public public public public public public public public
EXIT
Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.XX
Enable Traps
[NO] [NO] [NO] [NO] [NO] [NO] [NO] [NO]
Figure 5-16 The SNMP Traps Screen
The following explains each field of the SNMP Traps screen.
RETURNSAVE
2251-17
Trap Destination (Modifiable)
Indicates the IP address of the workstation to receive trap alarms. Up to eight different destinations can be defined.
Trap Community Name (Modifiable)
Displays the Community Name included in the trap message sent to the Network Management Station with the associated IP address.
5-34 2E43-51/2E43-51R User’s Guide
SNMP T raps Screen
Enable Traps (Toggle)
Enables transmission of the traps to the network management station with the associated IP address. This field toggles between YES and NO.
5.9.1 Configuring the Trap Table
To configure the Trap table, proceed as follows:
1. Use the arrow keys to highlight the appropriate Trap Destination
field.
2. Enter the IP address of the workstation that is to receive traps. IP
address entries must follow the DDN format. For example: 134.141.79.121
3. Press ENTER. If an invalid entry is entered, the message “INVALID
IP ENTERED” displays.
4. Use the arrow keys to highlight the Trap Community Name field.
Enter the community name.
5. Press ENTER.
6. Use the arrow keys to highlight the Enable Traps field. Press the
SPACE bar to choose either YES (send alarms from the 2E43-51 to the workstation), or NO (prevent alarms from being sent).
7. Use the arrow keys to highlight the SAVE command and press
ENTER. The message “SAVED OK” displays on the screen.
NOTE
Exiting without saving causes a “NOT SAVED?” message to appear above the SAVE command. Edits are lost if the y are not saved before exiting.
8. To exit the screen, use the arrow keys to highlight RETURN and press
ENTER.
The designated workstations now receive traps from the 2E43-51.
2E43-51/2E43-51R User’s Guide 5-35
Chapter 5: Local Management
8

5.10 SWITCH CONFIGURATION SCREEN

NOTE
operational mode of the device is set to SECURE FAST VLAN. This screen may only be used when the device is configured to operate as an 802.1D or 802.1Q switch.
The Switch Configuration screen, Figure 5-17, provides the basic setup options to make a switch operational in your network.
T o access the Switch Configuration screen from the De vice Configuration Menu screen, use the arrow keys to highlight the SWITCH CONFIGURATION menu item and press ENTER. The Switch Configuration screen displays showing up to 7 ports, depending on if there are Fast Ethernet Interface Modules and an HSIM installed in the device.
The Switch Configuration screen is not available if the
Event Message Line
Device Name: 2E43-51
Switch Address: 00-00-1D-00-00-00 Number of Ports: 7
Port #
MAC Address
2E43-51 LOCAL MANAGEMENT
Switch Configuration
State
Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.XX
Type of STA: Age Time (sec): 300
[DEC]
Status
1 2 3 4 5 6 7
00-00-1D-00-00-00 00-00-1D-00-00-01 00-00-1D-00-00-02 00-00-1D-00-00-03 00-00-1D-00-00-04 00-00-1D-00-00-05 00-00-1D-00-00-06
EXIT
learning listening standby learning listening standby listening
[ENABLED] [DISABLED] [ENABLED] [DISABLED] [ENABLED] [DISABLED] [ENABLED]
RETURNSAVE
22511-1
Figure 5-17 Switch Configuration Screen
5-36 2E43-51/2E43-51R User’s Guide
Switch Configuration Screen
The following describes each field of the Switch Configuration screen:
Switch Address (Read-Only)
Displays the MAC address of the switch.
Number of Ports (Read-Only)
Displays the total number of switched ports on the 2E43-51.
NOTE
Type of STA (Toggle)
Ethernet networks 1 through 4 (ENET 1 through ENET 4) are considered as single switched ports.
Allows the user to set the method that switches use to decide which switch is the controlling (Root) switch when two or more switches exist in parallel (Spanning Tree Algorithm). Valid selection is IEEE, DEC, and None. To set the STA, refer to Section 5.10.1.
Age Time (Modifiable)
Allows the user to set the amount of time (in seconds) that the 2E43-51 keeps an address in its switch table before discarding it. An address is automatically discarded when a valid Bridge Protocol Data Unit (BPDU) is not received from that address within the time specified in the Age T ime field. To change the Age T ime field from the default v alue of 300 seconds, refer to Section 5.10.2.
Port # (Read-Only)
Lists each switched port on the device.
MAC Address (Read-Only)
Displays the hardware address assigned to each listed port.
State (Read-Only)
Disabled: Management disabled this interface. No traffic is received or forwarded while the interface is disabled.
Listening: The switch is not adding information to the Transparent Database. The switch is monitoring the Bridge Protocol Data Unit (BPDU) traffic while preparing to move from the learning to the forwarding state.
2E43-51/2E43-51R User’s Guide 5-37
Chapter 5: Local Management
Learning: The switch is learning the addresses on this interface. The switch enters the learning state when the Transparent Database is created (during start-up or after being deleted), or when the Spanning Tree Algorithm detects a network topology change.
Forwarding: The switch is operating and this interface is forwarding traffic.
Blocking: This interface will not forward any traffic through the switch because a loop condition has been detected by the STA.
Status (Toggle)
Allows the user to disable or enable a port by setting the status of the listed interface to either ENABLED or DISABLED. To set the port status, refer to Section 5.10.3.

5.10.1 Setting the STA

The Spanning Tree Algorithm (STA) setting allows the user to set the method that the switches use to decide which is the controller (Root) switch when two or more switches are in parallel. The av ailable selections are IEEE, DEC, and NONE.
To set the STA, proceed as follows:
1. Use the arrow keys to highlight the Type of STA field.
2. Use the SPACE bar to step to the appropriate setting of IEEE, DEC,
or NONE.
3. Use the arrow keys to highlight the SAVE command at the bottom of
the screen.
4. Press ENTER. The message “SAVED OK” displays.

5.10.2 Setting the Age Time Field

To set the Age Time, proceed as follows:
1. Use the arrow keys to highlight the Age Time field.
2. Type in the desired Age Time in increments of 10. The available Age
Time range is 10 to 1,000,000 seconds with the default value being 300 seconds.
5-38 2E43-51/2E43-51R User’s Guide
Device Specific Configuration Menu Screen
3. Use the arrow keys to highlight the SAVE command at the bottom of
the screen.
4. Press ENTER. The message “SAVED OK” is displayed.

5.10.3 Setting (Enabling or Disabling) the Port Status

To set the status of an interface (port), proceed as follows:
1. Use the arrow keys to highlight the Status field of the port.
2. Use the SPACE bar to toggle to either ENABLED or DISABLED.
3. Use the arrow keys to highlight the SAVE command at the bottom of
the screen.
4. Press ENTER. The message “SAVED OK” displays.
5.11 DEVICE SPECIFIC CONFIGURATION MENU
SCREEN
The Device Specific Configuration Menu screen, Figure 5-18, allows the user to select one of five screens to configure ports or check system resources specific to the 2E43-51.
NOTE
2E43-51/2E43-51R User’s Guide 5-39
The PORT REDIRECT FUNCTION menu item on the Device Specific Configuration Menu screen does not display if the operational mode of the device is set to 802.1Q SWITCHING.
The PORT REDIRECT FUNCTION and BROADCAST SUPPRESSION menu items do not display if the operational mode is set to SECURE FAST VLAN.
Section 5.7.9 provides instructions on setting the operational
mode.
Chapter 5: Local Management
To access the Device Specific Configuration Menu screen from the Device Configuration Menu screen, use the arrow keys to highlight the DEVICE SPECIFIC CONFIGURATION menu item and press ENTER. The Device Specific Configuration Menu screen displays.
2E43-51 LOCAL MANAGEMENT
Device Specific Configuration Menu
Device Name: 2E43-51
SYSTEM RESOURCES HIGH SPEED INTERFACE CONFIGURATION FLASH DOWNLOAD PORT REDIRECT FUNCTION BROADCAST SUPPRESSION
802.1Q VLAN CONFIGURATION REPEATER CONFIGURATION MENU
Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.XX
EXIT
RETURN
22513-20
Figure 5-18 Device Specific Configuration Menu Screen
The following explains each selectable item in the Device Specific Configuration Menu screen:
SYSTEM RESOURCES
The System Resources screen displays the amount of FLASH memory, DRAM and NVRAM installed, indicates the amount of available memory and provides information on 2E43-51 operation. For details, refer to
Section 5.12.
HIGH SPEED INTERFACE CONFIGURATION
The High Speed Interface Configuration screen provides access to the Fast Ethernet Interfaces screen and the HSIM screen. For details, refer to
Section 5.13.
5-40 2E43-51/2E43-51R User’s Guide
System Resources Screen
FLASH DOWNLOAD
The FLASH Download screen allows the user to download information from FLASH memory and force the 2E43-51 to download a new image file from a TFTP server. For details, refer to Section 5.15.
PORT REDIRECT FUNCTION
The Port Redirect Function screen allows the user to redirect traffic from one or multiple switch ports to a specific destination switch port. For details, refer to Section 5.16.
BROADCAST SUPPRESSION
The Broadcast Suppression screen allows the user to set a desired limit of received broadcast frames that will be forwarded per port per second. F or details, refer to Section 5.17.
802.1Q VLAN CONFIGURATION
This menu item will only display if the 2E43-51 has been configured to operate as an 802.1Q switch as described in Section 5.7.9. When selected, this menu item opens the VLAN Main Menu screen. F or details about the VLAN Local Management screens, refer to the Cabletron Systems Port Based VLAN User’s Guide.
REPEATER CONFIGURATION MENU
The Repeater Configuration Menu screen enables the user to select the security screens: Device Level Security Configuration, and Port Level Security Configuration. For details refer to Section 5.18.

5.12 SYSTEM RESOURCES SCREEN

The System Resources screen, Figure 5-19, provides information concerning the processor used in the 2E43-51 and the amount of FLASH memory, DRAM, and NVRAM that is installed and how much of that memory is available. This screen also allows the user to monitor the current processor (switch) utilization and the peak switch utilization.
2E43-51/2E43-51R User’s Guide 5-41
Chapter 5: Local Management
To access the System Resources screen from the Device Specific Configuration Menu screen, use the arrow keys to highlight the SYSTEM RESOURCES menu item and press ENTER. The System Resources screen displays.
Event Message Line
Device Name: 2E43-51
Flash Memory Installed : 4 MB
DRAM Installed: 20 MB
NVRAM Installed: XX KB
SAVE
2E43-51 LOCAL MANAGEMENT
System Resources
CPU Type: i960 HT 25 Mhz
Available: XXXXX Bytes
Available: XXXXX Bytes
Available: XXXXX Bytes
Current Switch Utilization: 66% Peak Switch Utilization: 75%
Reset Peak Switch Utilization: [NO]
EXIT
Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.XX
RETURN
RETURN
2251-23
Figure 5-19 System Resources Screen
The following briefly explains each field of the System Resources screen.
CPU Type (Read-only)
Indicates the microprocessor used in the 2E43-51.
Flash Memory Installed (Read-only)
Indicates the amount of FLASH memory installed in the 2E43-51 and how much is currently available.
DRAM Installed (Read-only)
Indicates the amount of DRAM installed in the 2E43-51 and how much of it is currently available.
5-42 2E43-51/2E43-51R User’s Guide
System Resources Screen
NVRAM Installed (Read-only)
Indicates the amount of NVRAM installed in the 2E43-51 and how much of it is currently available.
Current Switch Utilization (Read-only)
Shows the percentage of the device switching capacity currently being used.
Peak Switch Utilization (Read-only)
Shows the peak percentage of device switching capacity used, since the last reset.
Reset Peak Switch Utilization (Toggle)
Allows the user to reset the Peak Switch Utilization field. The switch may be set to either YES or NO as described in Section 5.12.1. YES resets the Peak Switch Utilization field to the current system traffic.

5.12.1 Setting the Reset Peak Switch Utilization

To set the Reset Peak Switch Utilization field to YES or NO, proceed as follows:
1. Use the arrow keys to highlight the Reset Peak Switch Utilization
field.
2. Press the SPACE bar to select YES or NO.
3. Use the arrows keys to highlight the SAVE command at the bottom of
the screen.
4. Press ENTER. The message “SAVED OK” displays.
2E43-51/2E43-51R User’s Guide 5-43
Chapter 5: Local Management
5.13 HIGH SPEED INTERFACE CONFIGURATION MENU
SCREEN
The High Speed Interface Configuration Menu screen, Figure 5-20, applies to the Fast Ethernet Interface Modules and the High Speed Interface Module.
NOTE
Interface Modules and a High Speed Interface Module (HSIM) are installed.
If only the Fast Ethernet Interface Module(s) or the HSIM is installed, then the respective F ast Ethernet Interfaces screen or the HSIM Setup screen displays instead of the High Speed Interface Configuration Menu screen.
To access the High Speed Interface Configuration Menu screen from the Device Specific Configuration Menu screen, use the arrow keys to highlight the HIGH SPEED INTERFACE CONFIGURATION menu item and press ENTER. The High Speed Interface Configuration Menu screen displays.
This screen does not display unless one or two Fast Ethernet
Event Message Line
Device Name: 2E43-51
2E43-51 LOCAL MANAGEMENT
High Speed Interface Configuration Menu
Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.XX
FAST ETHERNET INTERFACES HSIM
SAVE
EXIT
RETURN
22511-53
Figure 5-20 High Speed Interface Configuration Menu Screen
5-44 2E43-51/2E43-51R User’s Guide
High Speed Interface Configuration Menu Screen
The following briefly explains each screen accessible from the High Speed Interface Configuration Menu screen.
FAST ETHERNET INTERFACES
Displays a screen named High Speed Interface Configuration. This screen shows the types of Fast Ethernet Interface Modules installed in ports 5 and 6, their current operating mode, and indicates if the ports are linked. This screen also allows the user to enable or disable Auto-Negotiation and set the Advertised Ability. For details, refer to Section 5.14.
HSIM
Displays the types of interfaces installed in the High Speed Interface Module (HSIM) slots. The HSIM screens are described in their respective user’s guides.
2E43-51/2E43-51R User’s Guide 5-45
Chapter 5: Local Management
5.14 HIGH SPEED INTERFACE CONFIGURATION
SCREEN
NOTE
applies only to ports 5 and 6. This screen supports the FE-100TX, FE-100FX, and FE-100F3 Fast Ethernet Interface Modules that operate at 100 Mbps.
The High Speed Interface Configuration screen displays the types of interfaces installed in ports 5 and 6, their current operating mode, and indicates if the ports are linked. This screen also allows the user to enable or disable Auto-Negotiation and set the Advertised Ability.
To access the High Speed Interface Configuration screen from the High Speed Interface Configuration Menu screen, use the arrow keys to highlight the FAST ETHERNET INTERFACES menu item and press ENTER. The High Speed Interface Configuration screen displays.
The High Speed Interface Configuration screen, Figure 5-21,
Event Message Line
Device Name: 2E43-51
Port Type Link Status Current Oper. Mode Desired Oper. Mode Advertised Ability
2E43-51 LOCAL MANAGEMENT
High Speed Interface Configuration
Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.XX
Port 5 FE-100TX Link 100Base-TXFD
[Auto-Negotiation] [100Base-TXFD] [Disabled]
Port 6 Unknown N/A [N/A] [N/A] [N/A]
SAVE
EXIT
RETURN
2251-24
Figure 5-21 High Speed Interface Configuration Screen
5-46 2E43-51/2E43-51R User’s Guide
High Speed Interface Configuration Screen
The following briefly explains each field of the High Speed Interface Configuration screen.
Port Type (Read-only)
Displays the type of interface (FE-100FX, FE-100TX, FE-100F3, or Unknown) installed in ports 5 and 6. Figure 5-21 shows that there is an FE-100TX interface installed in port 5 and no interface indicated by Unknown in port 6.
Link Status (Read-only)
Indicates whether or not there is a physical connection from this port to another 10BASE-T or 100BASE-TX/FX device. One of the following values displays:
Link – There is a link signal present and a valid physical connection
to another device.
No Link – There is no link signal present and no valid physical
connection to another device.
Current Oper. Mode (Read-only)
This field displays the current operating mode of ports 5 and 6. Depending on whether a 100BASE-FX or 100BASE-TX Fast Ethernet Interface Module is installed, this field displays the following:
With a 100BASE-FX interface: 100Base-FX, 100Base-FXFD (full
duplex), or N/A when the port slot is empty.
With a 100BASE-TX interface: Unknown, 10Base-T, 10Base-TFD
(full duplex), 100Base-TX, 100Base-TXFD (full duplex) or N/A when the port slot is empty.
Desired Oper. Mode (Selectable)
This field allows the user to select the desired operational mode for an interface in port 5 or 6. The field toggles between 100Base-FX and 100Base-FXFD (full duplex) when an FE-100FX or FE-100F3 is installed. Section 5.14.1 describes how to configure a port with an FE-100FX or FE-100F3.
2E43-51/2E43-51R User’s Guide 5-47
Chapter 5: Local Management
NOTE
In normal operation, the port with an FE-100TX installed automatically establishes a link with the device at the other end of the segment without requiring user setup. However, Local Management provides the user with the option of manually configuring that port.
If an FE-100TX is installed, the field steps to Auto-Negotiation, 10Base-T, 10Base-TFD (full duplex), 100Base-TX, and 100Base-TXFD (full duplex). In normal operation, the port with an FE-100TX installed is capable of auto-negotiating the operational mode and no further user setup is required. Section 5.14.2 describes how to manually configure an FE-100TX.
In Auto Negotiation, the FE-100TX negotiates to the highest common denominator of the two interfaces. The order of priority of negotiation is 100Base-TXFD, 100Base-TX, 10Base-TFD, and 10Base-T.
Advertised Ability (Selectable)
During auto-negotiation, the FE-100TX “tells” the device at the other end of the segment about its capabilities. The capabilities of a port (5 or 6) with an FE-100TX installed are 10Base-T, 10Base-TFD (full duplex mode), 100Base-TX and 100Base-TXFD (full duplex mode). In normal operation, with all capabilities enabled, the FE-100TX “advertises” that it has the ability to operate in any mode. The Network Manager may choose to set up the port so that only a portion of the available capabilities are advertised and the others are disabled. For example, only 100Base-TX and 100Base-TXFD might be enabled so that only devices that operate at 100 Mbps can communicate with that port. Section 5.14.2.2 describes how to enable or disable advertised modes.
5.14.1 Configuring an FE-100FX or FE-100F3
When an FE-100FX or FE-100F3 is installed in port 5 or 6, it must be manually set to operate in the same technology as the device at the other end of the connected segment. Section 5.14.1.1 provides instructions for manually configuring the port with an FE-100FX or FE-100F3 interface.
5-48 2E43-51/2E43-51R User’s Guide
High Speed Interface Configuration Screen
5.14.1.1 Setting the FE-100FX or FE-100F3
Operational Mode
Use the Desired Oper. Mode field to set the active technology. This field toggles between 100Base-FX and 100Base-FXFD (full duplex). To set the active technology through Local Management, proceed as follows:
1. Use the arrow keys to highlight the Desired Oper. Mode field.
2. Use the SPACE bar to select 100Base-FX or 100Base-FXFD (full
duplex).
3. Press ENTER. The port now operates in the chosen mode.
4. Use the arrow keys to highlight the SAVE command. Press ENTER.
The message “SAVED OK” displays and Local Management saves the changes to memory.
5.14.2 Configuring an FE-100TX
In normal operation, a port (5 or 6) with an FE-100TX interface automatically establishes a link with the device at the other end of the segment and no user setup is required. Section 5.14.2.1 and
Section 5.14.2.2 provide instructions for manually configuring the port
with an FE-100TX installed.
5.14.2.1 Setting the FE-100TX Operational Mode
Use the Desired Oper. Mode field to set the active technology. This field steps between Auto-Negotiation, 10Base-T, 10Base-TFD (full duplex), 100Base-TX, and 100Base-TXFD (full duplex). If Auto-Negotiation is selected, the FE-100TX automatically sets the active technology. To manually set the active technology through Local Management, proceed as follows:
1. Use the arrow keys to highlight the Desired Oper. Mode field.
2. Use the SPACE bar to select the desired mode. Press ENTER. If any
mode other than Auto-Negotiation is selected, the port only operates in the chosen mode and Auto-Negotiation is disabled.
2E43-51/2E43-51R User’s Guide 5-49
Chapter 5: Local Management
3. Use the arrow keys to highlight the SAVE command. Press ENTER.
The message “SAVED OK” displays and Local Management saves the changes to memory. The selected mode is displayed in both the Desired Operational Mode field and the Current Operational Mode field.
5.14.2.2 Setting the FE-100TX Advertised Ability
In normal operation, a port (5 or 6) with an FE-100TX auto-negotiates to the highest speed possible. Under some circumstances, the Network Administrator may want the port to advertise only some of the available modes. The Advertised Ability field provides the capability to set those modes. This field steps to 10Base-T, 10Base-TFD (full duplex), 100Base-TX, and 100Base-TXFD (full duplex). To set the advertised ability, proceed as follows:
1. Use the arrow keys to highlight the Advertised Ability field.
2. Use the SPACE bar to select the desired mode.
3. Use the arrow keys to move to the Enable/Disable field at the right of
the desired mode and use the SPACE bar to select Enabled or Disabled. Press ENTER.
4. Continue this process until you have completed enabling or disabling
the advertised modes.
5. Use the arrow keys to highlight the SAVE command. Press ENTER.
The message “SAVED OK” displays and Local Management saves the changes to memory.

5.15 FLASH DOWNLOAD SCREEN

The Flash Download screen, shown in Figure 5-22, allows the user to upgrade the device with a different operating image.
NOTE
5-50 2E43-51/2E43-51R User’s Guide
The user may also force the do wnload of an image by changing the position of Switch 6 located inside the device. For details about setting the switch, refer to Section C.2.1.
FLASH Download Screen
Before downloading an image to the device, copy the image to the network TFTP server .
NOTE
server, refer to the specific workstation documentation.
To access the Flash Download screen from the Device Specific Configuration Menu screen, use the arrow keys to highlight the FLASH DOWNLOAD menu item and press ENTER. The Flash Download screen displays.
For information on how to set up a workstation as a TFTP
TFTP DOWNLOAD. WILL COMMIT TO FLASH. REBOOT IN PROGRESS...
Device Name: 2E43-51
2E43-51 LOCAL MANAGEMENT
Flash Download
Download Method: Reboot After Download: TFTP Gateway IP Addr:
Last Image Server IP:
Last Image File Name:
Download Server IP:
Download File Name:
Firmware Revision: XX.XX.XX BOOTPROM Revision: XX.XX.XX
[TFTP] [YES]
134.141.79.123
134.141.79.121 /tftpboot/2E43.hex
134.141.79.121 /tftpboot/2E43.hex
EXECUTE
EXIT
RETURN
2251-49
Figure 5-22 Flash Download Screen
Download Server IP and Download File Name display only
NOTE
when TFTP or RUNTIME are selected in Download Method.
2E43-51/2E43-51R User’s Guide 5-51
Chapter 5: Local Management
The following briefly explains each field of the Flash Download screen:
Download Method (Selectable)
This field steps to BOOTP, TFTP, and RUNTIME. If set for BootP, the device sends out a BootP request to determine the IP address of the TFTP server and the file name of the image to be downloaded. If set for TFTP or RUNTIME, the 2E43-51 attempts a TFTP download based on the IP address and file name entered in the fields at the bottom of the Flash Download screen. Section 5.15.1 describes how to do wnload using BootP.
Section 5.15.2 describes how to download using TFTP. Section 5.15.3
describes how to download using Runtime.
Reboot After Download (Modifiable only when RUNTIME is chosen)
This field notifies the user that the 2E43-51 will reboot after the download is complete. If a Runtime Download is performed, this field toggles between YES and NO. If YES is selected, the device reboots after the download is completed. If NO is selected, the device continues using the existing firmware image and stores the new firmware image in FLASH memory . When the device is reset or during the next power-up, the de vice will boot from FLASH memory using the new image.
TFTP Gateway IP Addr (Selectable)
This field shows the IP address of the TFTP gate w ay serv er defined in the General Configuration screen in Section 5.7.4, Setting the TFTP
Gateway IP Address.
Last Image Server IP (Read-only)
This field shows the IP address of the server used for the pre vious FLASH Download.
Last Image File Name (Read-only)
This field shows the complete path and file name of the last image downloaded to FLASH.
5-52 2E43-51/2E43-51R User’s Guide
Loading...