Page 1
192DMX Controller
!
User ,s Manual
BANK
1
00
TURN ON TURN OFF CENE1
01
TURN ON TURN OFF ENE2
02
TURN ON TURN OFF SCENE3
03
TURN ON TURN OFF SCENE 4
04
TURN ON TURN OFF SCENE5
05
TURN ON TURN OFF SCENE6
06
TURN ON TURN OFF SCENE7
07
TURN ON TURN OFF SCENE8
Page 2
MAIN FEATURES
1 . 192DMX Channels.
2. 30 Banks each composed of 8 programmable scencs.
3.8 fades adjusting output level.
4.Built –in Microphone.
5.AUTO mode is controllcd by TAP SYNC and SPEED controlled.
6.MIDI control through MIDI interface.
7.4 digits LED display.
8.Fird digit of LED shows CHASES , the second digit of LED shows
scenes.
9.Third and fourth digit of LED shows BANKS.
10.The second、third、fourth digit of LED show steps or 0-255 or
TIME.
11.Blackout master controlled by M annual or R emote.
12.CHASE programming and CHASE runnyng, manual control and
renote control.
13.Fade Time control.
14.DMX polarity selects.
TECHNICAL SPECIFICATION
Power Input: DC+9-12V
Output: AC230V～50Hz (AC120V～60Hz)300Ma ,DC9V300Ma.
Dimensions: 482×132×73mm
Weight: 2.5Kg
OPERATING INSTRUCTIONS
GENERAL DESCRIPTIONS:
Ⅰ. There is 192 DMX channel adjusting output level in every scene.
Ⅱ. 8scenes are available to be programmed for each bank. When scene
running, all scenes of one bank will be executed continuously in a cycle.
Ⅲ. Select desirde bank using UP and DOWN button, Also you can select
desired bank using MIDI signals through MIDI interface ,there are totally
BANK2
08
TURN ON TURN OFF SCENE1
09
TURN ON TURN OFF SCENE2
10
TURN ON TURN OFF SCENE3
”
”
BANK15
112
TURN ON TURN OFF SCENE1
113
TURN ON TURN OFF SCENE2
114
TURN ON TURN OFF SCENE3
115
TURN ON TURN OFF SCENE4
116
TURN ON TURN OFF SCENE5
117
TURN ON TURN OFF SCENE6
118
TURN ON TURN OFF SCENE7
119
TURN ON TURN OFF SCENE8
CHASE
120
TURN ON TURN OFF SCENE1
121
TURN ON TURN OFF SCENE1
122
TURN ON TURN OFF SCENE2
123
TURN ON TURN OFF SCENE3
124
TURN ON TURN OFF SCENE5
125
TURN ON TURN OFF SCENE6
126
BACKOUT
Page 3
30 banks, once only one can be chose.
Ⅳ.Scenes can be executed automatically ,and the duration is dependent
on TAP SYNC ,scenes are executed un der music or NOTE
triggering ,also press a scene buttons by hand to run scenes.
Ⅴ.There are total 6 chases, each contains240 scenes. You can choose
CHASES.
Running one or more ,and MIDI signal remote controlling.
2 .CONTROLS & FUNCRIONS
1.
seanners (1-12)
Ⅰ.Press music/Bank copy, corresponding indicator lights ,scene run is
engaged into MUSIC RUN.
Ⅱ.Select desired bank, rsing UP or DOWN or via MIDI signals.
Ⅲ.Press music /bank copy once more to withdraw MUSIC RUN.
4.MIDI RUN
Select bank to run scenes using MIDI whenever it is in MANUAL
RUN ,AUTO RUN or MUSIC RUN.
3.
CHASE RUN
Ⅰ.CHASE RUN requires making prograns, when runing CHASE, scene
will be step auto matching.
Ⅱ.CHASE RUN includes MANUAL RUN,AUTO RUN ,ATDIO RUNS,
and MIDI RUN.
Ⅲ.Eigher one CHASE more can be run in the order of selection .
Ⅳ.Press CHASE, Corresponding indicator lights, which indicates it, is in
CHASE RUN.
4.
FADE TIME CONTROL
Move the slider to adjust FADE, Output varies accordingly.
MIDI CHANNEL SETTING
1.
MIDI channel setting
Ⅰ.Press MIDI ,the third and fourgh digits of LED blink, selects MIDI
channel setting.
Ⅱ.Press MIDI one more to end MIDI channel setting. Also you can press
any other key except UP and DOWN or move the fades to end MIDI
channel setting.
Seanners
Channel
Fade control
LED
1
1-16
OFF
OFF
2
17-32
OFF
OFF
3
33-48
OFF
OFF
4
49-64
OFF
OFF
5
65-80
OFF
OFF
6
81-96
OFF
OFF
7
97-112
OFF
OFF
8
113-128
OFF
OFF
9
129-144
OFF
OFF
10
145-160
OFF
OFF
11
161-176
OFF
OFF
12
177-192
OFF
OFF
Seanners
Channel
Fade control
LED
1
1-16ONON
2
17-32ONON
3
33-48ONON
4
49-64ONON
5
65-80ONON
Page 4
2.
MIDI RUNNING
NOTE ON: Receive NOTE ON signals to execute corresponding
function.
Ⅰ.Select desired CHASE
Ⅱ.Press desired CHASE while holding Auto/DEL.
5. CLEAN ALL CHASE (ALL SCENES are stil availanble)
Ⅰ.Press DOWN +Auto /DEL while turning power off.
Ⅱ.Turn the power on.
RUNNING SCENES
●
Turn the power on it is in MANUAL RUN mode. when in
PROGRAM mode ,press PROGRAM for 2 seconel PROGRAM LED
goes out ,it enters MANUAL mode.
●
If there is not any scenes having been brogrammed in a bank, the
scene cant be run, only the SCENES having been brogrammed are
executed.
●
If the fades is set to OFF ,Scene will execute channel program setting.
1.
MANUAL URN
Ⅰ.Extinguish AUTO Triggered LED and MUSIC triggered LED.
Ⅱ.Select a bank (using ↑or ↓,MIDI signals through MIDI interface).
Ⅲ.Press scene to run scene.
Ⅳ.Press the SCANNER to copy to,then the SCANNER is copied to
anther SCANNER.
2. AUTO RUN
Ⅰ.Press AUTO/DEL ,corresponding, LED is ON.
Ⅱ.Press TAP SYNC/DISPLA,Press it onee more after some time ,the
interval between two bressing is assigned to the speed of AUTO RUN ,the
maximum limit is 10 minutes .If there are many pressings more than
twice ,the last two pressing are designated.
Ⅲ.Select desired bank, using UP or DOWN via MIDI signals.
Ⅳ.Press Auto/DEL once more to withdraw AUTO RUN mode.
3.
MUSIC RUN
Press desired scanner, corresponding LED is lit ,and appropriate channels
is enabled to be adjusted, when scenes are running ,if fades control is OFF
, channel output level is not controlled by the fades ,if fades if fades
control is ON, channel 8-output leve is controlled by the fades.
2. scene button
Press one scene button to run scene or to store, and the second digit of
LCD DISPLAY showsscenes 1-8.
3.fade(1-8)
Slide the fades to adjust the output level of DMX channel from 0 to FF.
(255)
4.PAGE SELECT
Press to select page A to B
1.
SPEED SLIDER
Move the slider to adjust chasing speed.
2.
FADE TIME SLIDER
Move the slider to adjust FADE TIME.
3.
LED DISPLAY
BANK
NOTE
NUMBER
FUNCTION
6
81-96ONON
7
97-112ONON
8
113-128ONON
9
129-144
ON
ON
10
145-160
ON
ON
11
161-176
ON
ON
12
177-192
ON
ON
Page 5
4.
BAND button (↑or↓)
Press UP or DOWN to increase or decrease Bank, the third and fourth
digit of LED DISPLAY shows BAND NO.(01-30)
5.
CHASE 1- CHASE 6
Select ddsired CHASE to be programmed or run CHASE.
6.
PROGRAM
T urn the power on ,it is in MANUAL RUN mode, press PROGRAM
for 2 seeonds, corresponding LED blinks, SCENE and CHASE are
ready to be brogrammed, press PROGRAM once more to return to
RUN mode, corresponding LED goes out.
7.
MIDI/ADD
A、Press MIDI key when running ,the third and fourth digit of LED
flash, select MIDI channel using UP or DOWN, press MIDI key to make
programe when in PROGRAM mode.
B、Press this key to make programe when in PROGRAM mode.
8.
AUTO/DEL
A、In RUN mode, press Auto/Del, corresponding LED is ON ,which
indicates it is AUTO RUN mode, press once more to withdraw MUSIC
mode, corresponding. LED goes out.
B、Press this key to make S cene and chase program when in
PROGRAM mode.
9.
TAP SYNC /DISPLAY
A、In AUTO RUN mode, running speed of scene is interval of last
TWO pressing of TAP SYNC/DISPLAY ,Max.10 minutes.
B、In PROGRAM mode, select display between STEP and BANK ,in
other mode: Select display between 00-225 and 0%-100%.
10.
BLACKOUT
Press this key to disable all channel output, but not any other functions
.Press once withdraw Black out mode.
11.
MIDI IN Use to receive MIDI data.
12.
DMX POLARITY SELECT
Select the polarity of DMX output.
13.
DMX OUT
Use to output DMX 512 signal
14.
DC INPUT
DC9V～12V ,300 Ma ,MIN.
PROGRAMMING FOR SCENES
Press PROGRAM for 3 second, appropriate LED blink ,which indicates it
in PROGRAM mode .
1.
SECNE PTOGRAMMING
Ⅰ.Press SCANNER key to select DMX channel composed. Of 8
channels.
Ⅱ.Select different channel to conrtol several devices at the same time.
Ⅲ.A djust appropriate fades to select desired output level ,then turn off
fade.
Ⅳ.Selcet and adjust output level continuously until all devices are set.
Ⅴ.Press MIDI /ADD.
2. SCANNER COPY
Ⅰ. Select desired scene of bank.
Ⅱ.Make program of scene of scene to meet the requirement of device.
Ⅲ. Press MIDI/ADD ,add a programmed scenes.
3. SCENE EDITING
●Add a STEP in CHASE .Select desired LCD display Presses TAP
SYNC/DISPLAY ,the LCD shows the CHASE and its STEP, If it has
made program till the 15th step ,select the 9th using UP or DOWN, Press
MIDI/ADD, the CHASE is maintained and the STEP turns to 10th STEP.
Seleet desired SCENE using UP or DOWN ,Press MIDI/REC ,then the
new 10th STEP is added to SCENE, the previous 10th STEP turns to the
new 11th STEP, the previous 11th STEP turns to the new 12th STEP, and
so on.
●Delete a STEP in CHASE
Select desired STEP and then press AUTO /DEL .
For example, select the 10th STEP using UP or DOW, press ATUO/
Page 6
DEL ,then 10th STEP is deleted, the previous 11th STEP turns to the 10th
STEP, the previous 12th STEP, and so on.
4.
DELETE A CHASE
Loading...