USB SuperBooster
Transmitter Dongle
Part #29348
User Manual
Introduction
Thank you for purchasing the USB SuperBooster Transmitter Dongle. The USB
SuperBooster Transmitter Dongle is one component of a complete solution that, when
paired with a receiver (sold separately) allows you to conquer USB length limitations and
put your USB devices where you need them. This wall plate solution extends the distance
of a USB device to a host computer up to 150ft so you can place your USB projector,
camera, printer, or other USB device exactly where you want it! The USB SuperBooster
Dongle is powerful yet simple, with no drivers to install or special software required. It
is also compatible with any computer that supports USB.
This plug-and-play device consists of a transmitter unit and receiver unit incorporated
into single gang Decora compatible wall plates or dongles. Numerous receiver options
are available so you can customize the configuration to meet your own needs. Choose
from a two-port wall plate receiver, a two-port dongle receiver, or a four-port dongle
receiver. These options are ideal for applications where you need more than one USB
device on the receiver side or you need a dongle instead of a wall plate on the receiver
side.
The transmitter/receiver pair is connected via standard Cat5, Cat5E, or Cat6 UTP cable
allowing for easy installation. This makes for a clean, finished installation important for
home owners, classrooms, offices and anywhere you don’t want visible cables lying
around. Use pre-terminated network cables or pull un-terminated cable and use the
included tool-less IDC RJ45 connector. The USB SuperBooster Dongle is bus-powered
so no external power source is required.
1
Features
• Extends the distance of a USB device from a USB-enabled computer up to 150ft
• One part of a total solution- receiver is purchased separately giving you the
flexibility to customize the configuration to your specific needs
• Receiver options include a 2-port wall plate (part #29345), a 2-port dongle (part #
29346), or a 4-port dongle (part #29347)
• Ideal for use with USB projectors, interactive whiteboards, cameras, printers,
web cams, hubs, and other USB devices
• Bus-powered so no external power source is required
• Uses standard Cat5/Cat5E/Cat6 patch cord (not included) for ease of use and
flexibility
• Included tool-less IDC RJ45 connector allows you to terminate your own cable
• Compliant with USB Specification 1.1
• Connectors:
o Transmitter: USB Type A Male; RJ45 Female
o Receiver (sold separately): USB Type A Female; RJ45 Female
*Decora™ is a registered trademark of Leviton Manufacturing Company, Inc. This Product is not manufactured or endorsed by the
Leviton Manufacturing Company, Inc.
Package Contents
• USB SuperBooster Dongle- Transmitter Unit
• (1) One RJ45 tool-less IDC connector
• User Guide
2
Installing your USB SuperBooster Dongle
The USB SuperBooster solution has a transmitter unit and a receiver unit (sold
separately).
Make certain you install the transmitter unit at your
computer or source side. The receiver unit needs to be installed on the
device side.
1) Connect the Transmitter unit to your source/computer
2) Install the Wall Plate Receiver unit in a standard J-box where you want your USB
device or connect the Dongle Receiver to your device
3) Use a pre-terminated Cat5/Cat5E/Cat6 cable (recommended) or terminate your
own cable using the tool-less RJ45 connectors included to connect the transmitter
and receiver together (see below for instructions on terminating your own cable)
4) If using a Wall Plate Receiver, plug your device into the receiver end (USB A
side) using a standard A/B (or A/Mini-B) USB cable (the green LED will light to
indicate you have a good connection to the wall plate)
5) Turn your computer/source on and begin using your device
Terminating a Cat5/Cat5E/Cat6 Cable Using the Tool-less IDC
1) Open the plug by lifting the clear
plastic end
2) Pin 1 of the connector is on the
left side of the clear plastic shell
while Pin 8 is on the right side of
the connector (with RJ45
connector facing away from you)
3) Thread the white/orange
conductor on your Cat5/5E/6
cable into Pin 1
4) Thread the orange conductor on
your Cat5/5E/6 cable into Pin 2
5) Thread the white/green
conductor on your Cat5/5E/6
cable into Pin 3
6) Thread the blue conductor on
your Cat5/5E/6 cable into Pin 4
7) Thread the white/blue conductor
on your Cat5/5E/6 cable into Pin
5
8) Thread the green conductor on
your Cat5/5E/6 cable into Pin 6
9) Thread the white/brown
conductor on your Cat5/5E/6
cable into Pin 7
10) Thread the brown conductor on
your Cat5/5E/6 cable into Pin 8
11) Repeat steps 1-10 to terminate
the other end of your Cat5/5E/6
cable
Pin 1
Pin 8
3
Termination Chart
Pin Number Network (Cat5/5E/6)
Conductor Color
1 white/orange
2 orange
3 White/green
4 Blue
5 White/blue
6 Green
7 White/brown
8 brown
Application Diagram
Transmitter Receiver
3555 Kettering Blvd.
Moraine, Ohio 45439
1-800-293-4970
www.cablestogo.com
1
Loading...