C2G USB 2.0 TO DVI-I ADAPTER User Manual

Page 1
SER GUIDE
U
USB 2.0 TO DVI-I ADAPTER
Model: 30535
1
Page 2
TABLE OF CONTENTS
Introduction.................................................................................................................................................2
Features......................................................................................................................................................3
System Requirements.................................................................................................................................4
Package Contents.......................................................................................................................................5
Device Overview.........................................................................................................................................6
Device Driver Installation on Windows 2000/XP
Device Installation on Windows 2000/XP..........................................................................................7
Verifying Device Driver on Windows 2000/XP.................................................................................19
Device Driver Un-Installation on Windows 2000/XP........................................................................21
Device Driver Installation on Windows Vista
Device Installation on Windows Vista..............................................................................................23
Verifying Device Driver on Windows Vista.......................................................................................29
Device Driver Un-Installation on Windows Vista..............................................................................31
Function Description
Function Description........................................................................................................................33
Supported Common Display Resolution...................................................................................................39
Technical Specifications............................................................................................................................40
Questions & Answers................................................................................................................................41
Troubleshooting Tips.................................................................................................................................42
Regulatory Compliance.............................................................................................................................43
Cables To Go One Year Warranty............................................................................................................44
Important Safety Information.....................................................................................................................45
1
Page 3
INTRODUCTION
Thank you for purchasing the USB 2.0 to DVI-I Adapter. This product will allow you to easily expand your PC’s display capabilities via an available USB port. No need to open your computer case or install a special graphics card – this cable-based adapter uses a simple connection to provide support for a secondary monitor. View large spreadsheets over two screens, read email messages and attachments on separate monitors, deliver multi-screen presentations without a second computer, or expand your graphic design workstation. We recommend that you read this manual thoroughly and retain for future reference.
2
Page 4
FEATURES
Supports display resolutions up to VGA: 1920 x 1200 / DVI: 1600 x 1200 Supports the multiple display devices on one PC Multi graphics display modes – Primary, Extended, Mirror and Rotation USB 2.0 compliant and Plug-and-Play USB connectivity VGA and DVI outputs compliant
3
Page 5
SYSTEM REQUIREMENTS
Pentium 4 / Celeron Family, AMD K6 / Athlon / Duron Family. 1.0GHz or higher processor Single Display Setup: 256MB RAM or higher; Multi-Display Setup: 512MB RAM or higher-(Higher memory recommended for optimal performance) Available USB 2.0 port Windows 2000 SP4 / Windows XP SP2 / Windows Vista
4
Page 6
PACKAGE CONTENTS
USB 2.0 to DVI-I Adapter USB 2.0 cable DVI to VGA adapter (for VGA capable displays) CD (User Manual, Driver and Utility) Quick Installation Guide
5
Page 7
DEVICE OVERVIEW
DVI-I Female Port
USB Mini-B Port
DVI to VGA Adapter
Power LED Indicator
6
Page 8
DEVICE INSTALLATION ON WINDOWS® 2000/XP
Please note the following information before installation:
Do not plug the USB 2.0 to DVI-I Adapter to your PC or Notebook while executing the set-up or un-
installation program.
The AC power adapter is required for the external USB Hub. Please note that the driver allows up to
6 USB 2.0 to DVI-I Adapters on one PC.
Connect the display device to the DVI connector of USB 2.0 to DVI-I Adapter and switch it on before
plugging it into an available USB 2.0 port of PC or Notebook.
DO NOT reboot the computer until all of USB 2.0 to DVI-I Adapters are installed.
Installing the device driver enables your computer’s operating system to recognize the USB 2.0 to DVI-I Adapter once it’s connected. Please check your operating system and refer to the appropriate installation procedure to begin installing the device driver. Please make sure the USB 2.0 to DVI-I Adapter is unplugged from your PC or Notebook before executing the setup program. simple device driver installation procedure for computer running Windows 2000 / XP operating system.
This section illustrates the
7
Page 9
DEVICE INSTALLATION ON WINDOWS® 2000/XP
Step 1
Insert the program does not begin automatically, click Start, Run and double click “ path of your CD-ROM drive).
Step 2
Driver Installation Wizard, click “
Driver
CD into the CD-ROM drive; the setup program
Next
” to continue.
should be launched
automatically. If setup
D:\Setup.exe
” (where D: is the
8
Page 10
DEVICE INSTALLATION ON WINDOWS® 2000/XP
Step 3
License Agreement; please read it and select
terms of the license agreement
.” Click “
the License Agreement.
Step 4
The Microsoft Software Installation Certificate warning dialogue box will be displayed on Windows XP several times. Please select “
Continue Anyway
” to continue with the device driver installation. This will not affect the device driver installation and the device usage.
I accept the
Next
” to accept
9
Page 11
DEVICE INSTALLATION ON WINDOWS® 2000/XP
Step 5
Click “
Step 6 Select “Yes, I want to restart my computer now” and click “Finish” to complete the driver installation. Note: If you are installing multiple USB 2.0 to DVI Adapters select No, I will restart my computer later at this step and refer to page 14 of this manual
for further instructions.
Finish
” to exit the Driver Wizard.
10
Page 12
DEVICE INSTALLATION ON WINDOWS® 2000/XP
Step 7
Connect the external display device (monitor/projector) to the DVI connector of
Adapter
PC or Notebook.
and switch it on. Then plug the USB 2.0 to DVI-I Adapter into an available USB 2.0 port of your
By default this adapter will set the additional monitor as an “extended desktop” display.
To change the setting of the display output, please refer to Function Description section of this manual.
Application Diagram
USB 2.0 to DVI-I
11
Page 13
DEVICE INSTALLATION ON WINDOWS® 2000/XP
Step 7
It will show the Hardware Installation Wizard, please select “No, not this time” and click “Next” to continue.
Step 8 Select “Install the software automatically (Recommended)”. Click “Next” to continue.
12
Page 14
DEVICE INSTALLATION ON WINDOWS® 2000/XP
Step 9
Please select “ device driver installation (this may appear several times). This will not affect the device driver installation and the device usage.
Step 10 Click
“Finish
to DVI-I Adapter and you are now ready to use the product.
Continue Anyway
” to continue with the
” to exit the Hardware Wizard of the USB 2.0
13
Page 15
DEVICE INSTALLATION ON WINDOWS® 2000/XP
Step 11b. I
NSTALLATION OF MULTIPLE
a. Please select “ and click “
Finish
No, I will restart my computer later.
” to continue the installation of next USB
2.0 to DVI-I Adapter.
USB 2.0
TO
DVI-I A
DAPTERS
14
Page 16
DEVICE INSTALLATION ON WINDOWS® 2000/XP
b. Connect another display device to the DVI connector of the next USB 2.0 to DVI-I Adapter and switch it on. Then plug the USB 2.0 to DVI-I Adapter into next available USB 2.0 port of your PC or Notebook.
c. The Hardware Installation Wizard will appear. Please select “
No, not this time
” and click “
Next
” to continue.
15
Page 17
DEVICE INSTALLATION ON WINDOWS® 2000/XP
d. Select “
(Recommended)
e. Please select “
device driver installation. It will not affect the device driver installation and the device usage.
Install the software automatically
and click “
Continue Anyway
Next
” to continue.
” to continue with the
16
Page 18
DEVICE INSTALLATION ON WINDOWS® 2000/XP
f. Click “
2.0 to DVI-I Adapter.
g. If you wish to install additional USB 2.0 to DVI-I Adapter, please follow the procedure of
Finish
” to exit the Hardware Wizard of the 2nd USB
a~ f again
.
17
Page 19
DEVICE INSTALLATION ON WINDOWS® 2000/XP
h. Otherwise, please select “
computer now.
installation.
After you reboot the computer, the extended display will be shown on the display device.
” and click “
Yes, I want to restart my
Finish
” to complete the driver
18
Page 20
VERIFYING DEVICE DRIVER INSTALLATION ON WINDOWS® 2000/XP
The following procedure allows you to verify the device driver installation.
Right click “My Computer” “Properties” “Hardware” “Device Manager”. Double click “Display adapters”, and “Universal Serial Bus controllers”.
¾ SINGLE USB 2.0 TO DVI-I ADAPTER INSTALLATION ON THE COMPUTER
19
Page 21
VERIFYING DEVICE DRIVER INSTALLATION ON WINDOWS® 2000/XP
ULTIPLE USB 2.0 TO DVI-I ADAPTER INSTALLATION ON THE COMPUTER
¾ M
20
Page 22
DEVICE DRIVER UN-INSTALLATION ON WINDOWS® 2000/XP
Please make sure the USB 2.0 to DVI-I Adapter is executing the device driver un-installation program.
Step 1 Start menu:
Click
Programs
Classic
Click “
or Remove Programs
Select
Interface (Multiple) driver version no.”
“Start” → “Control Panel” → “
”.
start menu:
Start” → “Settings” → “
“USB 2.0 External Graphics Card with DVI
Remove”
button.
”.
Add or Remove
Control Panel” → “
item. Click
unplugged
Add
from your PC or Notebook before
21
Page 23
DEVICE DRIVER UN-INSTALLATION ON WINDOWS® 2000/XP
Step 2
Unplug the USB 2.0 to DVI-I Adapter and click “ continue.
Step 3
Select “ “
Finish
un-installation.
Yes, I want to restart my computer now
” to reboot. After reboot, you will complete the driver
OK
” to
” and click
22
Page 24
DEVICE INSTALLATION ON WINDOWS® VISTA®
Please note the following information before installation:
Do not plug the USB 2.0 to DVI-I Adapter to your PC or Notebook while executing the set-up or un-
installation program.
The AC power adapter is required for the external USB Hub. Please note that the driver allows up to
6 USB 2.0 to DVI-I Adapters on one PC.
Connect the display device to the DVI connector of USB 2.0 to DVI-I Adapter and switch it on before
plugging it into an available USB 2.0 port of PC or Notebook.
DO NOT reboot the computer until all of USB 2.0 to DVI-I Adapters are installed.
Installing the device driver enables your computer’s operating system to recognize the USB 2.0 to DVI-I Adapter once it’s connected. Please check your operating system and refer to the appropriate installation procedure to begin installing the device driver. Please make sure the USB 2.0 to DVI-I Adapter is unplugged from your PC or notebook before executing the setup program. simple device driver installation procedure for a computer running Windows Vista® operating system.
This section illustrates the
23
Page 25
DEVICE INSTALLATION ON WINDOWS® VISTA®
Step 1
Insert the Driver CD into the CD-ROM drive; the setup program program does not begin automatically, click Start, Run and double click “ path of your CD-ROM drive).
Step 2
Driver Installation Wizard, click “
Next
” to continue.
should be launched
automatically. If setup
D:\Setup.exe
” (where D: is the
24
Page 26
DEVICE INSTALLATION ON WINDOWS® VISTA®
Step 3
License Agreement; please review it and check “
the terms of the license agreement.
accept the License Agreement.
” Click “
Step 4
Windows Security warning dialogue box under Windows Vista, it will not affect the device driver installation and usage the device. Please select “
from “Magic Control Technology Corp.
Install
” to continue.
Always trust software
”, then click
I accept
Next
” to
25
Page 27
DEVICE INSTALLATION ON WINDOWS® VISTA®
Setup is searching for installed features…
Step 5
Click “
Finish
” to exit the Driver Wizard.
26
Page 28
DEVICE INSTALLATION ON WINDOWS® VISTA®
Step 6
NSTALLATION OF SINGLE
Please select and click “
Yes , I want to restart my computer now.”
Finish
” to complete the driver installation. Note: If
you wish to install additional USB 2.0 to DVI Adapters, select
No, I will restart my computer later
next page.
After you reboot the computer, you should see the extend
nd
display on the 2
display device.
Step 7
Connect the external display device (monitor/projector) to the DVI connector of
Adapter
and switch it on. your PC or notebook and you are ready to use. Refer to page 11 for the application diagram. By default this adapter will set the additional monitor as an “extended desktop” display. To change the setting of the display output, please refer to the user manual which is located on the disc.
USB 2.0
TO
DVI-I A
, and refer to
DAPTER
Step 8
on the
USB 2.0 to DVI-I
Then, plug the USB 2.0 to DVI-I Adapter into an available USB 2.0 port of
27
Page 29
DEVICE INSTALLATION ON WINDOWS® VISTA®
Step 8 (optional) I
NSTALLATION OF MULTIPLE
a.
Please select “
Finish
” to continue the next installation.
No, I will restart my computer later.
b. Connect another external display device to the DVI
connector of next USB 2.0 to DVI-I Adapter and switch it on.
c. Plug the USB 2.0 to DVI-I Adapter into an available USB
2.0 port of your PC. The driver installation will process automatically.
d. If you wish to install additional USB 2.0 to DVI-I Adapters, please follow procedure
e. Otherwise, select “
driver installation.
After you reboot the computer, the extended display will be shown on the display device.
USB 2.0
TO
DVI-I A
DAPTERS
” And click
Yes, I want to restart my computer now.
” and click “
Finish
a~ c again
.
” to complete the
28
Page 30
VERIFYING DEVICE INSTALLATION ON WINDOWS® VISTA®
The following procedure allows you to verify the device driver installation.
Right click “Computer” “Properties” “Device Manager”. Double click “Display adapters”, and “Universal Serial Bus controllers”.
¾ SS
IINNGGLLEE
UUSSB
B
22..0
0
TTOO
DDVVII--I
A
DDAAPPTTEERR
A
NNSSTTAALLLLAATTIIOONN OONN TTHHEE CCOOMMPPUUTTEER
R
29
Page 31
VERIFYING DEVICE INSTALLATION ON WINDOWS® VISTA®
M
¾¾ M
UULLTTIIPPLLEE
UUSSB
B
22..0
0
TTOO
DDVVII--I
A
DDAAPPTTEERR
A
NNSSTTAALLLLAATTIIOONN OONN TTHHEE CCOOMMPPUUTTEER
R
30
Page 32
DEVICE DRIVER UN-INSTALLATION ON WINDOWS® VISTA®
Please make sure the USB 2.0 to DVI-I Adapter is the device driver un-installation program.
Step 1
Please click “
Start menu:
Start”
“Control Panel” →
Program and Features”
 Classic Start menu:
Please click “
→ “
Control Panel” → “
Start” → “Settings”
Program and
Features”
Select “
USB 2.0 External Graphics Card with DVI Interface (Multiple)
Step 2
Unplug the USB 2.0 to DVI-I Adapter and click “ continue.
OK
unplugged
” to
to your PC or notebook before executing
” item. Click “Uninstall” button.
31
Page 33
DEVICE DRIVER UN-INSTALLATION ON WINDOWS® VISTA®
Step 3
Select “ “
Finish
installation.
Yes, I want to restart my computer now
” to reboot. After reboot, you will complete the driver un-
” and click
32
Page 34
FUNCTION DESCRIPTION
This section describes the main functions provided by the USB 2.0 to DVI-I Adapter.
- It can support a LCD or CRT monitor, and it
supports four kinds of selections, Primary, Extended, Mirror and Rotate by “UD” icon.
33
Page 35
FUNCTION DESCRIPTION
- The resolution supports from 800x600 x16 bit and up-to 1920x1200 x16 bit.
- The resolution can be modified via the system tray or Display Properties.
34
Page 36
FUNCTION DESCRIPTION
“Primary” Mode
The system’s main graphics adapter will automatically switch to act as the secondary graphics adapter and the main screen will now work as the extended desktop. The monitor connected to the USB 2.0 to DVI-I Adapter will now act as the primary Windows desktop. Please be advised that some display utility and drivers that shipped with certain AGP and built-in display adapters may prevent this option from working on some systems. You can disable the other utility program (usually found in the same toolbar located on the bottom right hand corner) to make this function work properly.
35
Page 37
FUNCTION DESCRIPTION
“Extended” Mode (Default)
By default, the monitor connected to USB 2.0 to DVI-I Adapter will work as, “Extended Desktop” which extends the primary Windows desktop of your system. You can change the relative position of this extended desktop under the Display Properties.
36
Page 38
FUNCTION DESCRIPTION
“Mirror” Mode
By setting this mode, the Windows desktop will be mirrored/replicated to the secondary CRT/LCD monitor. The screen resolution setting on the secondary monitor will follow the primary screen’s resolution. For example, if the primary resolution is 1024x768x32bit, and the secondary monitor’s resolution will be the same. On the other hand, if the selected resolution setting is not supported by the primary screen, a warning dialogue box will be displayed and the suggested screen resolution will be shown.
“Rotate” Mode
This feature enables setting the orientation of the secondary CRT/LCD monitor. Several options such as “0 degrees”, “90 degrees”, “180 degrees” or “270 degrees” are available under the Extended or Primary mode.
37
Page 39
FUNCTION DESCRIPTION
“OFF” Mode
This option disables the USB 2.0 to DVI-I Adapter on the system.
38
Page 40
SUPPORTED COMMON DISPLAY RESOLUTION
Aspect Ratio Resolution VGA DVI 16:10 1920 * 1200 16 N/A
16:9 1920 * 1080 16 N/A 16:10 1680 * 1050 16, 32 16, 32 16:10 1440 * 900 16, 32 16, 32 16:10 1280 * 800 16, 32 16, 32 15:9 1280 * 768 16, 32 16, 32 5:4 1280 * 1024 16, 32 16, 32 4:3 1600 * 1200 16, 32 16, 32 4:3 1400 * 1050 16, 32 16,32 4:3 1280 * 960 16, 32 16,32 4:3 1152 * 864 16, 32 16,32 4:3 1024 * 768 16, 32 16,32 4:3 800 * 600 16, 32 16,32
39
Page 41
TECHNICAL SPECIFICATIONS
Operating System Windows 2000/XP/Vista
PCB Version UDA200 Version:1.1
USB 2.0 Cable Length: 100± 5 cm, ( mini
DVI connector DVI-I (DVI Digital &
Case Material ABS
Power Source Bus Powered
Monitor Refresh Frequency 60, 70, 75 & 85 (Hz)
B-A type)
Analog)
Dual Link ( female)
40
Page 42
QUESTIONS & ANSWERS
This section describes the common Q&A regarding to the installation or operation of the USB 2.0 to DVI-I Adapter.
Q: Why can’t I make the USB 2.0 DVI-I Adapter the primary display?
A: Some video cards ship their product with a utility that prevent other video cards from being set as the primary card.
Check the bottom right hand corner taskbar for the utility. Disable the utility before switching our adapter to be the primary display.
Q: Why won’t my DVD player work when I move it over to the extended display?
A: Some DVD playback software packages do not support playing on a second display adapter of any kind. You may try
to open the program in the secondary display first before playing the DVD.
Q: Why won’t my video play on Windows Media Player if I move it over to the extended desktop?
A: Check that you have moved the Media Player window completely over to the second screen.
Q: Why does my mouse not move pass the right side of the screen as it should on extended desktop?
A: Check the display settings and make sure that your display number ‘2’ is on the right side of display number ‘1’. You
can rearrange how Windows treats each display in relation to each other in the Display Properties Settings.
Q: There are lines running horizontally up and down my screen.
A: This is due to a low refresh rate setting. You can change this in the Display Properties Settings Advanced Monitor.
Make sure you select the USB 2.0 to DVI-I Adapter first and not set the refresh rate higher than what your monitor can support. This may damage your monitor. You can also try to reset/refresh/resynchronize your monitor.
Q: Direct3D does not work?
A: This is a current limitation of the adapter. Please check for driver updates in the future to add support for this. If your
application requires this, please use the main display adapter.
41
Page 43
TROUBLESHOOTING TIPS
The following troubleshooting tips may help if you are experiencing any difficulties using our device.
- Check to make sure that all connectors are plugged in correctly.
- Make sure that the USB port that you are using is USB 2.0.
- Try a different USB 2.0 port and/or computer
- Check to see that the monitor is connected correctly and the power is ON.
- Try connecting the adapter directly to the computer instead of through a hub.
- Unplug all other USB devices from the system.
- Make sure to restart your computer after the driver installation.
- Unplug the adapter and re-insert it.
- Check the website (www.cablestogo.com) to make sure you have the latest drivers.
- Reset/refresh/resynchronize your monitor.
- Selecting Primary Mode may disable the main system display on certain Intel graphics solution
based computer system.
- If you have problems during the boot up process, start your computer in Safe Mode and uninstall the driver. Hold the
CTRL key until the Windows startup menu appears and select Safe Mode.
- To verify the driver version that you installed, please click “Control Panel” “Add or Remove
Programs” to check the program: USB 2.0 External Graphics Card with DVI Interface (Multiple)
8.1.0.0521.0155 (this number is the driver version).
42
Page 44
REGULATORY COMPLIANCE
FCC
This equipment has been tested and found to comply with FCC rules Part 15 Subpart B
§ 15.109/15.107 Class B. Operation is subject to the following two conditions:
• This device may not cause harmful interference
• This device must accept any interference received, including interference that may cause undesired operation.
CE This equipment is in compliance with the requirements of the following regulations: EN 55022 Class B (2006), EN 55024 (1998+A1:2001+ A2:2003), IEC/EN 61000-3-2 (2006), IEC/EN 61000-3-3 (1995+A1 :2001+A2 :2005), (IEC/EN 61000-4-2 (1995+A1 :1998+A2 :2001)/-3 (2006)/-4(2004)/-5(2006)/
-6 (1996+A1 : 2001)/-11 (2004)
C-Tick
This equipment is in compliance with the requirements of the following regulations: EN 55022 (2006), AS/NZS CISPR22 © IEC: 2005.
VCCI
This equipment is in compliance with the requirements of the following regulations: CISPR22 © IEC: 2005.
43
Page 45
CABLES TO GO ONE YEAR WARRANTY
At Cables To Go, we want you to be totally confident in your purchase. That is why we offer a one year warranty on this device. If you experience problems due to workmanship or material defect for the duration of this warranty, we will repair or replace this device. To request a Return Merchandise Authorization (RMA) number, contact customer service at 1-800-506-9606 or www.cablestogo.com.
Cables To Go
3555 Kettering Blvd.
Moraine, OH 45439
1-800-506-9607
www.cablestogo.com
44
Page 46
IMPORTANT SAFETY INFORMATION
! Do not plug the unit in any outlet that does not have enough current to allow the switch to function. Refer to the
specifications in this manual for power level of the unit.
! Liquid: If this unit or its corresponding power adapter has had liquid spilled on or in it, do not attempt to use the unit. Do not attempt to use this product in an outdoor environment as elements such as rain, snow, hail, etc. can damage the product.
! In case of a storm, it is recommended that you unplug this device from the outlet.
! Avoid placing this product next to objects that produce heat such as portable heaters, space heaters, or heating ducts.
! THERE ARE NO USER SERVICEABLE PARTS
Do not attempt to open this product and expose the internal circuitry. If you feel that the product is defective, unplug the unit and refer to the warranty information section of this manual.
©2009.Cables To Go is a trademark of Cables To Go. Microsoft and XP/Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. This product is not endorsed or manufactured by Microsoft Corporation.
45
Page 47
46
Page 48
For more information on this product or to check for updated drivers, manuals or frequently asked questions please visit our website.
www.cablestogo.com
VER. 1.0.4.9.09
47
Loading...