C2G 1-PORT 60 GHZ WIRELESSHD KIT User Manual

USER GUIDE

1-PORT 60 GHZ WIRELESSHD KIT

Model: 29670

1

TABLE OF CONTENTS

Introduction.................................................................................................................................................2

Features......................................................................................................................................................3

Package Contents.......................................................................................................................................4

Device Overview.........................................................................................................................................5

Device Installation.......................................................................................................................................8

Troubleshooting.........................................................................................................................................11

Technical Specifications............................................................................................................................12

FCC Statement.........................................................................................................................................15

Cables To Go Warranty............................................................................................................................16

Important Safety Information.....................................................................................................................17

1

INTRODUCTION

Thank you for purchasing the TruLink™ 1-Port 60 GHz WirelessHD Kit. The TruLink™ 1-Port 60 GHz
WirelessHD Kit enables high definition wireless transmission between your television and your HDMI
components. Enjoy full HD 1080p signal from your computer, Blu-ray player, set-top box, gaming
console or other HDMI device to your HDMI enabled television. The 60 GHz transmission capability
means greater flexibility in your home theater setup by allowing you to place the components up to 33
feet apart or possibly more depending on the environment*.

The TruLink 1-Port 60 GHz WirelessHD Kit is ideal for situations where in-wall cabling is either not
feasible (such as in plaster, brick or exterior walls) or not desired (such as in apartments or other rental
properties). By offering true uncompressed A/V transmission, the TruLink WirelessHD kit is a quick,
convenient and reliable cable replacement. This plug-and-play solution requires no software, no drivers
and no setup – simply connect the receiver with the HDMI component and instantly transmit content to
your television. We recommend that you read this manual thoroughly and retain for future
reference.

*Although performance characteristics may exceed stated distance limitations depending on the environment they are in, the following
best practices are recommended to ensure optimal results.

The transmitter and receiver should:

• Face each other within the same room.

• Be located within 33 feet each other.

• Be placed at the same level, i.e. the transmitter should not be placed higher than the receiver.

• Be located in open spaces, i.e. not in a cabinet or enclosed shelf.

2

FEATURES

CONVENIENT

Supports wireless transmission up to 33ft/10M in-room (longer distances may be supported depending on the



environment)*

 Plug-and-play solution means no drivers, software, or setup required
 Auto Power function will automatically turn off the attached component when the transmitter is turned off
 Transmitter and receiver each have on/off switch to conserve power when not in use
 Transmitter and receiver are wall-mountable*

R

ELIABLE

WirelessHD 1.0 certified


 Meets Digital Transmission Content Protection (DTCP) protocol
 Compatible with other WiHD enabled consumer electronics bearing the logo
 HDMI 1.3 compatible
 FCC and CE approvals

H

IGH PERFORMANCE

36 antenna array provides a strong wireless signal


 Data transfer rates of up to 4 Gbps
 Supports true uncompressed 1080p@60Hz resolutions
 Supports 7.1 channel surround sound

3

PACKAGE CONTENTS

 (1) 60GHz WirelessHD Transmitting Unit
 (1) 60GHz WirelessHD Receiving Unit
 (2) HDMI Cables
 (2) Power Adapters
 Remote Control
 Mounting Bracket
 User Guide

4

DEVICE OVERVIEW

TRANSMITTER UNIT RECEIVER UNIT

LED Indicators

LED Color Behavior Indication

The LED will illuminate when the power is connected and the
power switch is turned on.

Power

On

Green

Off The LED will be dark when the power switch is turned off.
Blinking Unit in sleep mode.

On The LED will illuminate to indicate which RX is being selected.

Link

Weak

Strong

Blue

Green

Green

Off If the pairing LED is off, user has to reset both devices.
Blinking Waiting for link.

On Indicates the signal is weak, the Strong LED will be off
Off No link or no signal
On Indicates the signal is strong, the weak LED will be on
Off Signal weak, the weak LED will be on

5

DEVICE OVERVIEW

TRANSMITTER AND RECEIVER SIDE PANEL VIEW

Buttons

Reset

CFG
(Configure)

TRANSMITTER AND RECEIVER REAR PANEL VIEW

Press the “RESET” button to reset the system,
the system will run through a full reset which
takes approximately 5 seconds.

This button is only for manufacturer usage.

Configuration

DC-IN
Switch

HDMI

Connect the power adapter to the power DC-IN port.
Switch the button to turn on or off the power supply.
Connect HDMI cable one end to this HDMI port and the other to the

DVD player or computer HDMI port or DTV HDMI port.

6

DEVICE OVERVIEW

REMOTE CONTROL

Remote Controller

Sleep
HDMI

Remove the plastic film before using the
remote control

The devices will be ready while this button clicking.
Switch HDMI port, it is only for multi-HDMI port model.

7

DEVICE INSTALLATION

Step 1
Connect the 60GHz WirelessHD Transmitter with an HDMI cable to an input source, such as a computer
or a DVD player.

Step 2
Connect the 60GHz WirelessHD Receiver with an HDMI cable to a display device, such as a monitor or
projector.

8

DEVICE INSTALLATION

Step 3
Connect both power adapters of the Transmitting and Receiving units to outlets.

Step 4
Turn on the power of both the Transmitter and Receiver units.

9

DEVICE INSTALLATION

Step 5
After you have finished the above set up steps, the units will be ready to transmit media. You can power
on your source and display device and begin use.

Please note the below diagram for recommended product placement in a room set-up:

10

TROUBLESHOOTING

The following are some things you can try if you are not getting any or getting poor picture and sound.

 Try moving the units closer together making sure they are level with and facing each other
 Check all audio and video equipment and make sure correct inputs are selected and all

connections are secure

 Try lowering the video resolution on your source device to isolate possible bandwidth issue
 Make sure you are only using the power adapters that came with the units as changing out may

have different specifications not suitable for operating the units.

 Make sure the power switch on the units is in the “on” position

11

TECHNICAL SPECIFICATIONS

Standards

WirelessHD, HDMI(V1.3 with Deep
color)

Frequency

Input/ Output Interface

Antenna Type

Range

AV Port

Physical Specifications

Adapter Power

LED Indicators

Operating Environment
(Total System)

60 GHz
HDMI interface

36 Antenna Array (Integrate
Ceramic)

10 meters inroom usage,
Transmitter : 1 Port (CEC pass

through)
Receiver : 1 Port (CEC pass through)

Weight: 367g±10g
Dimension: L=187mm / W=85mm /

H=44.8mm

AC 90-230V @ 60Hz input, DC 12V

1.5A
Transmitter: Four LEDs display,

power, link indicator, signal Strength
indication
Receiver : Four LEDs display, power,
link indicator, signal Strength
indication

Operating Temperature: 0 ~ 40
ambient temperature
Storage Temperature: -30 ~ 70
Operating Humidity: 10% to 90%
(Non-condensing)
Storage Humidity: 5% to 90% (Non­condensing)

12

TECHNICAL SPECIFICATIONS

VIDEO FORMAT

Auto detect 17 modes

TV mode
Resolution 23.94 / 24 Hz 50 Hz 59.94 / 60 Hz

640X480I ● X X ●
640X480P ● X X ●
720X480P ● X X ●
720X576I ● X ● X
720X576P ● X ● X
1280X720P ● X ● ●
1920X1080I ● X ● ●

1920X1080P

VESA mode Vertical Refresh Rate
Resolution 60 Hz
640 X 480 ●
800 X 600 ●
1024 X 768 ●
1280 X 1024 ●

Deep Color

Only support 12bit at 23.94 /

24 Hz

and YUV4:2:2 12bit 60Hz ● ● ●

Vertical Refresh Rate

13

TECHNICAL SPECIFICATIONS

AUDIO FORMAT

Smple rate
(256 Fs)

LPCM 2ch

LPCM 8ch
AC3

(Dolby)
2ch~6ch

DTS
2ch~6ch

32 kHz 44.1 kHz 48 kHz 88.2 kHz 96 kHz 176.4 kHz 192 kHz

● ● ● ● ● ● ●

● ● ● ● ● X X

X X ● X X X X

X X ● X X X X

14

FCC STATEMENT

FCC RF Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20 cm between the radiator and
your body. This transmitter must not be co-located or operating in conjunction with any other antenna.

FCC Part 15 Class B Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

z Reorient or relocate the receiving antenna.
z Increase the separation between the equipment and receiver.
z Connect the equipment into an outlet on a circuit different from that to which the receiver is needed.
z Consult the dealer or an experienced radio/TV technician for help.

15

CABLES TO GO™ WARRANTY STATEMENT

At Cables To Go, we want you to be totally confident in your purchase. That is why we offer a one year
warranty on this device. If you experience problems due to workmanship or material defect for the
duration of this warranty, we will repair or replace this device. To request a Return Merchandise
Authorization (RMA) number, contact customer service at 1-800-293-4970 or www.cablestogo.com.

Cables To Go

3555 Kettering Blvd.

Moraine, OH 45439

1-800-826-7904

www.cablestogo.com

16

IMPORTANT SAFETY INFORMATION

! Do not plug the unit in any outlet that does not have enough current to allow the device to function. Refer to the

specifications in this manual for power level of the unit.

! Liquid:
If this unit or its corresponding power adapter has had liquid spilled on or in it, do not attempt to use the unit.
Do not attempt to use this product in an outdoor environment as elements such as rain, snow, hail, etc. can damage the
product.

! In case of a storm, it is recommended that you unplug this device from the outlet.

! Avoid placing this product next to objects that produce heat such as portable heaters, space heaters, or heating ducts.

! THERE ARE NO USER SERVICEABLE PARTS

Do not attempt to open this product and expose the internal circuitry. If you feel that the product is defective, unplug the
unit and refer to the warranty information section of this manual.

©2010.Cables To Go is a trademark of Cables To Go.

17

18

For more information on this product or to check for updated drivers,
manuals or frequently asked questions please visit our website.

www.cablestogo.com

VER. 1.0.3.22.10

19