IP/CCTV Tester Manual
99 Washington Street
Melrose, MA 02176
Phone 781-665-1400
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com
V2.10
CAMERA WIZARD II
TESTS
IP CAMERA TESTS
IP address scan: Scan IP cameras and network device’s for IP address
Link monitor: Displays all IP addresses for a given gateway
Port flicker: Blink a port’s link LED to identify ca ble location
PING test: Search for IP address to verify connectivity
POE tester: Displays PoE voltage
CAT5/6 cable tester: Performs a pairs test on CAT5/6 cables
Note: IP video image is not displayed o n LCD
CCTV CAMERA TESTS
Video image display: 3.5" LCD with 960x240 resolution
Video signal level meter: Display peak to peak value
PTZ camera controls for numerous ca mera types
RS485/RS422 input and data logging
3.5mm audio input
Built in speaker
Color bar signal generator
BNC input with 3' M-to-M BNC pigtail
POWER AND ACCESSORIES
Up to 11 hour battery life
4 hour recharge time
12VDC 1A output to power camera with 3’ pigtail
5VDC 2A AC adaptor powers and charges tester
Li-ion 3.7V 3000mAh rechargeable battery (replacement battery available)
Carrying case included
Contents
1、Safety information ................................................................................................................................. 1
2、Introduction ............................................................................................................................................ 2
2.1 General ........................................................................................................................................ 2
2.2 Features ....................................................................................................................................... 2
2.3 Function ...................................................................................................................................... 3
2.3.1 Video signal testing (CCTV) ........................................................................................ 3
2.3.2 Video signal level test (CCTV) ..................................................................................... 3
2.3.3 PTZ controller (CCTV) ................................................................................................. 3
2.3.4 Enhanced Color bar generator (CCTV) ........................................................................ 3
2.3.5 DC12V 1A output power (CCTV) ................................................................................ 3
2.3.6 Audio testing (CCTV) ................................................................................................... 3
2.3.7 Cable tester (CCTV AND IP) ....................................................................................... 3
2.3.8 RS485 Data Test (CCYV)............................................................................................. 4
2.3.9 PTZ address scanning (CCTV) ..................................................................................... 4
2.3.10 Image magnification（CCTV) ................................................................................... 4
2.3.11 Video snapshot (CCTV).............................................................................................. 4
2.3.12 Video record (CCTV) ................................................................................................. 4
2.3.13 Video playback (CCTV) ............................................................................................. 4
2.3.14 Port flicker (IP) ........................................................................................................... 4
2.3.15 IP address scan (IP) ..................................................................................................... 4
2.3.16 Link monitor (IP) ........................................................................................................ 4
2.3.17 PING test (IP) .............................................................................................................. 4
2.3.18 POE tester (IP) ............................................................................................................ 4
2.3.29 LED flashlight ............................................................................................................. 5
2.3.20 F1、F2 User-defined shortcut keys ............................................................................ 5
2.4 Accessories.................................................................................................................................. 5
2.5 Front Panel .................................................................................................................................. 6
3、Operation ............................................................................................................................................. 10
3.1 Installing the Battery ................................................................................................................. 10
3.2 Quick tester connection for CCTV use ..................................................................................... 11
3.3 OSD Menu ................................................................................................................................ 11
3.3.1 PTZ controller ............................................................................................................. 12
3.3.2 Color-bar generator ..................................................................................................... 15
3.3.3 Video in level .............................................................................................................. 15
3.3.4 PTZ address search ..................................................................................................... 16
3.3.5 10x zoom image display and Video out ...................................................................... 17
3.3.6 Photograph .................................................................................................................. 17
3.3.7 Video record ................................................................................................................ 18
3.3.8 Record playback .......................................................................................................... 18
3.3.9 PING Test .................................................................................................................... 19
3.3.10 Cable tester ................................................................................................................ 19
3.3.11 Port flicker ................................................................................................................. 20
3.3.12 Link monitor .............................................................................................................. 20
3.3.13 IP address scan .......................................................................................................... 21
3.3.14 PoE tester .................................................................................................................. 21
3.3.15 Data monitor .............................................................................................................. 22
3.3.16 Time setup ................................................................................................................. 23
3.3.17 Device (tester) setup .................................................................................................. 23
3.3.18 USB ........................................................................................................................... 24
3.4 DC12V 1A power output .......................................................................................................... 24
3.5 Audio input test ......................................................................................................................... 25
3.6 LED flashlight ........................................................................................................................... 25
4、Specifications ....................................................................................................................................... 25
4.1 General Specifications .............................................................................................................. 25
IP/CCTV Tester User’s Manual
1、Safety information
Notice
The tester is intended to be used in a respo nsible and safe manner and not in areas where the use
of electrical instruments could be dangerous (hospitals, gas stations etc.).
The tester should be kept dry. Dust and liquid should be avoided.
Like any instrument, treat carefully. Avoid dropping .
Don’t leave the tester alone when charging. If the battery is hot, the tester should be
disconnected from the electric source. The tester should not be charged for more than 8 hours.
Don’t use the tester where the humidity is high. Once the tester is damp, power off immediately
and move it away from other connecte d cables.
The tester should not be used in the environment with the flammable gas.
Do not disassemble the instrument, since no component inside can be repaired by the user. If the
disassembly is necessary, please contact the factory.
The instrument should not be used in a n environment with strong electrom agnetic interference.
Do not touch the tester with wet hands.
Do not use detergent to clean. Instead, use a dry cl oth. If the dirt i s not easy to remove, a sof t
cloth with water or neutral detergent c an be used.
Limited Warranty
Byte Brothers test equipment warrants to the ori ginal consumer that this product is in good
working order for a period of one year from the date of purchase. During the period this product
will be repaired or replaced without charge for either parts or labor unless this unit has been
damaged by the user. Repair or replacement as provided under this warranty is the exclusive
remedy of the purchaser.
1
IP/CCTV Tester User’s Manual
2.Introduction
2.1 General
The Camera Wizard II IP/CCTV tester is designed for the installation and maintenance of IP and CCTV
cameras and devices. CCTV tests: Video displa y, PTZ control, DC12V output power, audio test, color
generator, RS485 data decoding, picture and video recording, and image magnification. IP camera
tests: IP address scanning, PING te sting, Link monitor, POE measureme nt, Port flicker and CAT5/6
cable testing. Note: The color LCD screen will only display CCTV images (not IP images).
2.2 Features
High definition 3.5”TFT-LCD color display, 480(RGB)x320 (CCTV only)
Built-in LED flashlight
User-defined shortcut keys（F1 and F2）
Support for both NTSC/PAL video formats
10x zoom feature to magnify the video image (CCTV only)
Record and playback CCTV snapshots and videos using a micro SD card
(removable).
IP address scan to determine an IP camera’s IP address
PING an IP address to verify the connectivity of IP cameras or network devices
POE measurement to test the PoE switch’s voltage to the IP camera
Port Flicker blinks a switch port’ s link LED. Perfect for tracing cable locations.
Cable testing jack to test the pairs of a CAT5/6 cable.
Link monitor to display IP address usage on the network.
PTZ address scan to determine the address of a CCTV camera.
RS232/RS485/RS422 communication link to drive the PTZ unit.
PTZ testing for cameras so equipped. Driver sup ports more than thirty protocols.
DC12V 1000ma power output to te mporarily power CCTV camera during test.
Audio input jack to test audio signals
Lithium Ion Polymer Battery . This power-efficient battery can last 11 hours duri ng
normal use. Charging time is 4 -5 hours.
2
IP/CCTV Tester User’s Manual
2.3 Functions
2.3.1 Video signal display
Display the CCTV image on the built-i n high definition 3.5”LCD-TFT 480（RGB）x320
full-view display color screen. Supports PAL/NTSC. The LCD screen brightness/contrast/color and
saturation are adjustable. Note: The color LCD screen will only display CCTV images (not IP images)
2.3.2 Video signal level test
Test the CCTV video signal strength (attenuation). Longer video cables cause the image to dim and
reduces the image’s dynamic range. If the video signal is too strong, it will cause a virtual shadow and
reduce the sharpness of the image. The level test also displays the video level value and, if out of range,
a notice will be displayed on the screen.
2.3.3 PTZ controller
While displaying the CCTV image, this feature pans, tilts a nd zooms the PTZ base, if the camera is so
equipped. The tester emulates many common PTZ protocols and sets up the controlling parameters like
protocol, communication port, baud rate, PTZ ID and pan/tilt speed. These parameters can be stored and
recalled (“preset” positions).
2.3.4 Enhanced Color bar generator
The video generator is a PAL/NTSC multi-system color bar video generator used to test the security
system’s video monitors. With the video generator, you can judge whether the color is different because
of the transmission loss or interference.
2.3.5 DC12V 1000ma output power
Power the CCTV camera with the DC12V (1A) power output from the tester. This is helpful during
installation when camera power might not be available.
2.3.6 Audio testing
Test the audio input from pickup devices. Connect the tester and pickup device with the audio cable.
2.3.7 Cable tester
Test a CAT5/6 cable’s pinouts by using the cable test jack (UTP/SCAN) and the included remote.
Connect the CAT5/6 cable to the cable test jack. Connect the remote on the far end of the cable. The
cable test results show the pin-to-pin term ination of the wires.
3
IP/CCTV Tester User’s Manual
2.3.8 RS485 data test
Analyze the data coming from a RS485/RS422 device. The data is displayed in hexadecimal format.
2.3.9 PTZ address scanning
Discover the address of the PTZ camera.
2.3.10 Image magnification（10xZoom）
Set image 10x zoom, can view and display the details by 1x、2x、3x、4x、5x、6x – 10X zoom in the
monitor and tester.
2.3.11 Video snapshot
Capture the video image and save the current video frames as a JPEG file
2.3.12 Video record
Record and save the current video on a SD card.
2.3.13 Video playback
Playback the video images that have been saved on the SD card. The file directory name that is created
is based on the date setting of the tester.
2.3.14 Port flicker
Use this feature to blink the l ink LED o n a swi tch p ort. P erfect fo r tr acing the lo catio n of a cab le t hat i s
terminated into a live switch port.
2.3.15 IP address scan
Quickly determine a camera’s IP address with the IP address scan feature. The IP address scan steps
through every possible address in the network’s subnet to determine the IP camera’s address. The
subnet is entered into the tester as part of making the tester a part of the same network .
2.3.16 Link monitor
The link monitor lists the IP address of all network devices that it discovers in its own subnet. This is
useful in making sure there is not a conflic t with new IP addresses that are added to an existing network.
2.3.17 PING test
PINGING is a very popular network debugging tool. First, configure the tester with its own IP address
to make it a network device, then you use the tester to contact (ping) other Ethernet devices.
2.3.18 POE tester
Detect and display the existence of PoE power. When PoE power is present, the tester will measure and
4
IP/CCTV Tester User’s Manual
display the voltage that the PoE switch or injector is supplying to the IP camera.
2.3.19 LED flashlight
Light up the workspace with the ultrabright LED on the front of the tester.
2.3.20 F1, F2 User-defined shortcut keys
The user-defined shortcut keys can be setup to do your most popular tests.
2.4 Accessories
1). IP/CCTV camera and device tester
2). Power Supply: DC5V 1.2～1.5A（with included USB cable）
3). Cable test remote adaptor
4). Lithium Ion Polymer Battery（3.7V DC 3000mAh ）
5). BNC cable
6). RS485 cable
7). CCTV camera power cable
8). Audio cable
9). Safety cord
10). Tool bag
11). Instruction Manual
5
2
n
C
e
.5 Front Pa
IP/C
el
TV Tester Us
r’s Manual
6
C
c
m
i
c
R
e
e
e
w
u
v
u
V
e
w
l
h
n
g
h
l
n
n
d
w
e
m
b
t
p
r
h
p
e
v
s
e
e
w
h
m
p
n
a
o
t
）
a
e
IP/C
TV Tester Us
r’s Manual
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
OSD menu
The charge indi
is complete, the
The data-trans
The data-recept
The power indi
Set key, press it
Press more than
menu display
Confirm/Open :
Return/Close :
decrease the ap
Upward: Select
PTZ upward
User-defined ke
LED Lamp
Rightward，Ent
Add the value o
Number not use
Downward: Sel
Tilt the PTZ do
Leftward: Enter
Reduce the val
Record CCTV
Snapshot（capt
10xzoom CCT
WIDE: zoom in
ator: it lights red
indicator turns off
ission indicator: it
on indicator: it lig
ator: it lights gree
to enter sub-menu
2 seconds, turn on
Confirm the settin
eturn or cancel w
rture
the item which wil
y（User setting fu
r the sub-menu or
the parameter. Pa
ct the item which
nward
the sub-menu or s
e of the parameter.
ideos
re CCTV video i
images on screen
the image
hile the battery is
automatically
ights red while the
ts red while the da
while the tester is
to set the paramete
or off the device ,s
of parameters；o
ile setting paramet
be set or add the
ction, the default i
select the paramet
the PTZ right
ill be set or reduc
lect the parameter
Pan the PTZ left
age）
and video out
eing charged. As t
data is being trans
a is being received
owered on
s of functions
ort press to turn o
en or enlarge the
rs of the menu, cl
alue of the parame
“PTZ controller”
r whose value will
the value of the p
hose value will b
he charging
itted
or off the
perture
se or
er. Tilt the
be changed.
rameter.
changed.
7
IP/CCTV Tester User’s Manual
21
22
23
24
Near focus: Focus the image nearby
Far focus: Focus the image faraway
Menu key
TELE: zoom out the image
8
d
d
u
u
S
E
S
e
S
e
h
h
u
e
C
p
u
w
2
h
e
D
y
y
n
e
t
u
l
m
h
e
e
o
IP/C
TV Tester Us
r’s Manual
26 Vi
27 Vi
28 N
29 O
30 R
31 L
32 R
33 N
34 U
35 R
36 Et
37 Et
38 A
39 R
eo input (BNC in
eo output (BNC o
mber not used
tput DC12V1A po
232 interface: RS
D lamp
485/422 Interface:
twork cable /Telep
B data /charge int
ovable Micro S
ernet power suppl
ernet power suppl
dio input: Test the
set the default setti
ut interface): Inpu
tput interface): O
er, for provisiona
32 communication
RS485/RS422 co
one cable interfac
rface
card
output/Network t
input interface
camera’s audio pic
gs of tester
s the video
tputs the video
DC test supply
for the PTZ
munication for the
test
sting interface
kup and other audi
PTZ
equipment
9
3
o
n
a
i
h
e
y
e
5
n
r
h
h
a
mset
IP/C
C
y
n
s
b
r
n
h
a
t
c
n
n
t
s
e
e
s
p
n
m
o
n
f
b
t
n
a
a
t
t
p
b
a
e
a
r
u
TV Tester Us
r’s Manual
、Operati
3.1 Installi
The tester has
compartment)
Prior to using t
There is no ne
Pressing
Notice：Onl
The first tim
battery (4 to
The Charge I
when the cha
Notice: W
charged. T
Press the s
n
g the Batter
built-in lithium io
s disconnected for
e tester, open the
d to disconnect the
key powe
use the battery c
you use the tester,
hours for full rech
dicator ligh
ging is complete.
en the Charge Indi
e charging time ca
th
n 8 hours.
all RESET butto
tings (when the in
s on a
polymer recharg
afety during trans
attery compartme
battery during nor
d off the tester.
arger that comes
allow the battery t
rge). This extends
s red when chargi
ator turns o
be extended for a
on the left side of
trument works ab
able battery. The b
ortation.
t and connect the b
al use.
with the device
completely disch
the life of your ba
g the battery, then
f, the battery is ap
out 1 hour. Avoid
he tester to restore
ormally).
ttery (inside the b
attery.
rge. Then recharg
tery.
urns off automatic
roximately 90%
charging the batte
the factory’s defa
ttery
the
lly
y more
lt
10
Test Equipment Depot - 800.517.8431
99 Washington Street, Melrose, MA 02176
TestEquipmentDepot.com
3 3
s
t
o
e
t
w
a
R
n
h
y
y
t
C
o
c
e
Z
o
h
D
t
e
e
h
t
R
I
m
p
V
a
o
o
e
e
h
S
IP/C
TV Tester Us
r’s Manual
.2 Quick Te
Connec
display
To driv
transmi
image
To test
tester’s
PTZ co
ter connecti
the CCTV camera
n the tester screen
the video through
ter/receiver, conne
ill display on the t
camera with a PT
S485 interface (n
trollers, connect t
n for CCTV
’s video output to t
Note” IP camera i
the tester to a CCT
t the device to the
ster and monitor a
base, connect the
te the positive and
e cameras PTZ’s
use
e tester’s VIDEO
ages will not dis
monitor or optic
tester’s “VIDEO O
the same time.
camera’s RS485 c
negative polarity
S232 cable to the t
N jack. The image
lay on the screen.
l video
UT” jack . The vid
ntroller cable to t
f the cable). For R
ster’s RS232 jack.
will
eo
e
232
.3 Turn on t
Press the ke
Press the ke
timeout dura
e tester (OS
to turn on.
again to
ion is set in Devic
Menu)
urn off. The Auto
Settings.
11
3
D
kcaIf
P
P
nPP
f
P
N
n
n
a
t
m
n
t
s
i
o
p
R
、
r
e
u
v
C
o
e
y
s
n
d
s
i
a
p
n
n
e
c
t
t
)
z
d
a
p
f
p
.
k
w
h
t
h
r
k
y
e
e
s
e
m
n
IP/C
TV Tester Us
r’s Manual
Once the me
the key
In various fu
Functions th
The squares
First page
.3.1 PTZ contr
isplay the video i
ey to enter
ommunication por
nd recall preset po
there is no video
TX functions cann
TZ controller
I
the “PTZ CONT
ress the key
ress the key o
e
xit the menu.
I
there is no chang
ress to ret
ote: If there is no
u appears, choose
to enter the functi
ctional modes, pr
t require data entr
ell you if you are o
enu
oller
put (CCTV) and te
the PTZ setup me
, baud rate, PTZ a
itions.
nput, the screen di
t be accessed..
arameter sett
OLLER ”mode（
to move the
to change the
, press the
rn to the Main Me
ideo, the PTZ me
a desired tester fun
n and to exi
ss the key
(IP addresses, etc.
n menu 1, 2, or 3
Second page me
t the pan, tilt and
u. Setup the contro
dress, pan/tilt spee
plays “No video”
ng
s shown above，
yellow cursor to di
arameters’ values
ey to return to vie
u.
u is not functional.
tion by pressing t
the function.
o enter the parame
are entered with t
nu
oom base of came
lling parameters li
; set
nd the
ress the ke
ferent PTZ param
Then press the
ing the PTZ cam
e key. Pre
ers.
e keys.
Third page menu
as so equipped. Pr
e protocol,
to enter the para
ters.
key to save a
ra’s video.
s
ss the
eters.
d
12
A
Uth
h
CBM
PCM
6
DEEFG
MtoHMPP
A
h
. Protocol
w
e
s
c
r
n
r
0
t
i
r
t
r
p
T
r
i
C
m
h
Z
e
0
P
T
r
n
u
s
e
a
p
e
s
o
L
/
q
~
e
p
t
e
w
o
i
k
n
u
T
r
/
c
m
2
t
h
e
t
e
a
n
e
t
n
se the Up and Do
e “protocol ”. Sel
t
irty PTZ protocol
SR600、Panasoni
. Port
ove the yellow cu
TZ wires controlli
. Baud
ove the yellow cu
(
00/1200/2400/48
. Address
nter the address of
. Pan speed: Se
. Tilt speed: Set
. Set preset posit
ove the yellow cu
change the value.
. Call the prese
ove the yellow cu
ress key or
ress the key
IP/C
n arrow keys to
ct the protocol. T
. Such as Pelco-D、
、Sony-EVI etc.
sor to “port” Selec
g the camera’s PT
sor to “Baud”. Sel
0/9600/19200/576
the PTZ camera (0
the pan speed of
the tilt speed of P
on (Set PS) to sto
sor to “SET PS ”
Then press the
position (Go ps)
sor to “Go PS”. E
to change the val
to execute the pre
TV Tester Us
ove the yellow cur
e tester support m
Samsung、Yaan、
t which of the teste
base (RS232/422
ct the baud rate re
0/115200bps)
254). This setting
TZ camera (0~63)
Z camera (0~63)
e positions for lat
set and save
，
key to save. Pr
ter the preset you
e.
et position setting
r’s Manual
or to
re than
iLin、
’s communication
485).
uired by the PTZ
must match the ca
r recall
rese
position number (
ss to quit.
ish to recall (1~1
r press return key
ports will connect
amera.
era address .
1~128),Press the k
8).
o to quit.
o the
y
Check and set the
CCTV camera’s P
correctly, the teste
djusting and stor
t
e tester, use the fo
rotocol fields corr
Z base for the test
will control the c
ng preset (“PS”)
lowing keys to mo
ctly. The address,
and control to wor
mera’s PTZ and le
ositions: Once yo
ve the camera’s P
13
nterface and baud,
properly. When t
s.
have the PTZ bas
Z base:
must be the same
e parameters are e
properly connect
s the
tered
d to
S
A
BcPRE
PtopT
a
T
Cit
a
h
h
h
h
o
t
a
P
l
i
y
h
v
g
V
m
m
h
C
c
l
n
T
e
s
P
t
u
s
r
s
u
i
o
p
m
e
e
o
u
u
e
s
o
o
e
t
e
6
p
m
u
r
s
y
n
m
m
e
w
s
w
IP/C
TV Tester Us
r’s Manual
Press t
Press t
Press t
Press t
1) Set and G
etting a PTZ loca
. P/T/Z the camer
. Press the key
ursor to “Set PS”.
ress the key t
ecalling a preset
nter the preset pos
ress the ke
“GO ps”. Enter t
osition setting or
he camera will mo
utomatically chan
ips：Some CCT
2) Dome ca
heck your camera
s preset menu to t
. Press the key
b.Press the key
c
. Press the key
e key to
e key or
e key or
e key or
PS
ion for later reca
to desired positio
to enter the P
ress the k
o complete the pre
ocation (Go PS)
tion. (1~128) The
to enter PTZ con
e preset position n
key to quit.
e to the preset po
ed to the preset pa
cameras store pre
era menus
anual to see if yo
e tester by address
to enter PTZ c
, select preset
Enter the main
ontrol the PTZ dir
to switch on
adjust the foc
manually adj
l (Set PS)
.
Z controller subm
ys to select the pre
et position setting
TZ camera will g
roller submenu. Pr
mber. Then press
ition immediately:
ameters.
et position settings
r camera can stor
ng preset position
ntroller submenu
osition 64
enu of the PTZ ca
ction of rotation.
r turn off the apert
s manually.
st the zoom.
nu. Press the key
et position numbe
r preset return the
to the desired pre
ss the key
he enter ke
Zoom the lens and
that can be read o
presets. One exa
4.
era
re.
to mov
.
key to quit.
et position.
to move the yello
to complete the pr
the focus and iris i
the tester.
ple camera will do
e the
cursor
eset
nload
14
O
R
A
R
3
PPT
P
h3P
m
d
a
y
y
r
r
m
”
IP/C
C
u
u
g
/
e
ba
D
s
e
d
n
o
”
r
h
e
e
e
l
c
TV Tester Us
r’s Manual
SD Menu of Do
eference only)
fter accessing the
efer to the dome c
.3.2 Color bar
ress the ke
ress the ke
he Color bar gene
ress the key
“
Format”. The teste
t
e video output for
e (For
ome camera men
mera’s manual for
generator
to enter the men
to select the bar
ator supports PAL
or , move th
sends the color
ats.
, users can select
instructions.
.
enerator a
NTSC standard c
cursor to “Format
s from the “Video
ifferent functions t
d then press the
lor bars.
、“LCD display s
out” port. Press th
rough the arrow k
key
lect”、“Type ” se
key or to
eys
ect
hange
.3.3 Video “in
ress to the
level and LC
menu , pre
adjustment
s to enter.
15
Dco
3
P
Pse
fu
d
h
y
e
e
T
e
p
C
t
e
e
h
g
m
a
e
o
m
e
d
e
a
n
t
l
T
n
t
y
e
e
F
n
s
s
r
N
w
m
d
h
N
Use this
The Vi
result in
result in
Adjust t
epending on the t
hange between NT
f Radio Engineers)
.3.4 PTZ addr
ress to sel
IP/C
feature to analyze
eo Level should be
a dim picture with
washed out pictur
e tester’s LCD bri
pe of camera conn
C and PAL, and t
and mV. NTSC si
ss search
ct , press
TV Tester Us
he CCTV input vi
within the indicat
reduced dynamic r
s with decreased
ghtness, contrast a
cted to the CCTV
e Video Level wil
nals are measured
to enter.
r’s Manual
eo and auto displa
d range. Video lev
nge. A Video Lev
d color saturation.
ester, the Video “
automatically cha
in IRE units. PAL
the format (PAL/
ls that are too low
l that is too high
ormat ” will auto
ge between IRE (I
ignals are in mV.
TSC).
will
ill
atically
nstitute
Note：Please
the P
ress to sel
earch”, press
nction dis
isolate the PTZ ca
Z cameras in the s
ct , and th
to select ON
lays on the main
era from other P
me system will pa
n press to en
r OFF, then Press
enu.
16
Z cameras before
at the same time.
er (as follow pictu
to save. The
earching. Otherwis
e). Select to “Ad
PTZ address searc
e all
ress
N
Pth
P
h
h
Pth
M
w
P
3
WtoRm
3
W
T
n
y
e
t
l
t
l
d
u
i
e
g
g
e
p
n
C
e
s
a
0
t
o
s
e
’
p
a
i
b
g
h
o
r
e
D
o
n
s
g
u
s
z
e
m
t
c
e
l
a
p
m
G
a
ote：This functio
ress the ke
e PTZ camera’s s
ress the but
t
e PTZ camera wil
t
rough the search.
ress the but
e PTZ camera wil
anual search ad
hen the address fo
ress button
.3.5 10x zoom
hen video is pres
zoom out the ima
epeatedly pressin
onitor and the test
.3.6 Photogra
ith video present,
he stored image is
c
ard is installed or
IP/C
needs to be reset
to set the protoco
ttings.
on. The tester will
pan right. Press
on, the tester will
pan left. Press
ress: Press
nd. Press the dir
to quit.
mage display
nt, press to 1
e. Press
the 10x zoom key
screen.
h
press the key
named according t
ot. If no SD card i
TV Tester Us
ach time the tester
l, communication
scan for the camer
to stop search
earch for the PTZ
to stop searchin
or to searc
ection control butt
nd Video out
x zoom, press th
o see the details. P
changes the zoom
to save the current
the date. The test
installed, a “no S
r’s Manual
s power is turned
ort, communicatio
’s PTZ address. A
ng up. Press the
ase address. When
. Press to sin
the address grad
n to adju
e button to
ess to quit.
x、2x、3x、4x、
video frame on the
r automatically ch
Card” message is
ff.
rate. The should
the address is sear
key to single-s
the address is sear
le-step through th
ally, the image wil
t a Speed Dome C
oom in the image,
5x、6x -10X zoo
SD card as a JPE
cks as to whether
displayed on the sc
atch
ched,
tep
hed,
search.
flash
mera.
ress
on the
file.
SD
reen.
17
3
Wre
d
N
3
P
o
APm
o
e
t
a
e
i
a
u
h
t
r
C
e
a
g
r
y
i
a
o
e
n
)
l
t
g
c
e
n
s
v
o
a
i
t
o
n
s
s
0
t
IP/C
TV Tester Us
r’s Manual
.3.7 Video rec
ith video present,
cording, saving th
isappears. The file
ote: Press the bu
.3.8 Record pl
ress to sel
n the screen.
photograph file d
ress to start
eans there is a tot
Press to q
Press to c
Then press
to enter the files, p
rd
press mom
video to the SD c
is named accordin
ton for seve
yback
ct , press
splays with the
and stop video pla
l of 8 photos and v
it the latest storage
oose the files.
o show all the stor
ess to cho
ntarily. The blinki
rd (in AVI format
to the date.
al seconds and re
to enter, the la
icon in the top ri
back and, press
deo files, and the
image.
ge files, press
se the image.
g icon at the top l
. Press agai
ease to start, and
est photograph or
ht corner. A vide
to quit. In the
urrent file is the th
to choose
ft, means the vide
and the blinking i
top video recordi
ideo record file di
recording display
bove image, the 3/
rd.
he files. Press
is
con
g.
plays
a
0008
18
3
C
o
fthtoreAPto
n
t
P
3
P
t
6
o
t
r
i
s
t
n
C
p
g
t
n
n
y
e
c
k
i
a
s
u
o
t
a
L
e
e
.
t
y
%
y
IP/C
TV Tester Us
r’s Manual
.3.9 PING Tes
onnect the CAT5/
e
nter. Press
t
adjust the parame
I
the IP camera or
e screen. In this si
restart the Ping te
ceiving packet am
pplication
ING testing is one
ols. It is useful fo
etwork equipment
c
orrect.
I
is normal that the
ING testing proce
.3.10 Cable tes
ress to me
cable to the LAN
to adjust the
ter.
ther Ethernet equi
uation, the sendin
sting. With the equ
ount will be consis
of the most conve
verifying if the co
s working normall
first data packet wi
s.
er
u , press
port, press
IP address, Packet
ment is not conne
and receiving pac
pment connected
ent and the succes
tional network deb
nected IP camera
and the IP addres
ll be lost at the star
to enter.
to select ,
Size, Timeout, TT
ted to the tester, “c
et will be 0 and th
nd a valid IP addr
rate will be 100%
gging
r other
is
of the
nd then press
, Count. Press
onnect fail ” displa
success rate is 0
ss, the sending and
to
s on
. Press
19
C
Rse3P
pAT3P
6
o
k
e
w
n
e
IP/C
C
w
e
m
w
e
e
p
o
t
d
a
n
a
s
s
r
t
t
n
c
TV Tester Us
r’s Manual
onnect the CAT5/
emote adapter (sh
erial number of the
.3.11 Port flic
ress to sel
ort LED blinking s
LAN cable to the
wn). The cable’s
cable tester kit.
er
ct and th
gnal. This signal
tester’s UTP/Scan
iremap (sequence
n press to en
akes the connecte
ort. Connect the f
f wires) will be di
er. Press to
switch port flicke
r end of the cable
played, as well as
tart and stop sendi
at special frequen
o the
he
g the
y.
pplication
his test is an easy
：
.3.12 Link mo
ress to sel
ay to determine
itor
ct , and th
hich port a LAN c
n press to e
20
ble is using.
ter.
T
pst
A
W
o
m
3
T
F
P
oth
3
Pth
p
s
t
t
P
v
y
s
o
e
e
l
c
n
C
a
n
s
r
o
e
d
a
m
e
t
n
O
e
e
e
t
m
h
s
t
r
m
e
w
o
P
E
o
h
w
“
a
w
a
”
h
t
T
a
i
w
a
o
h
IP/C
TV Tester Us
r’s Manual
he link monitor di
ress to start
atus is“×”, means
pplication
hen adding an I
ccupied. If two de
onitor can quickl
.3.13 IP addre
his could be the m
irst, connect the IP
SI IN jack. Press
c
amera is found, its
c
onfigured to be on
s
o you can set the t
e cursor keys
.3.14 POE test
ress to se
e PoE power sour
ower source to tur
c
amera to the tester’
plays all active IP
the link monitor. If
he IP address is av
：
camera or other
ices are using the
check if an IP add
s scan
st popular IP test
camera to the test
to select
IP address will be
the same network
ster to have the sa
to give th
r
ect , and
e must both be co
on). First connect
s LAN jack. The P
ddresses that exist
the status is “√”, it
ailable
etwork device to
ame IP address, th
ess is occupied.
n the tester. Use it
r’s LAN jack. If th
. Press
isplayed. For this
s the camera (you
e). To configure t
tester an IP addre
hen press
nected to the teste
the PoE cable to th
E voltage will be
on a network seg
means the IP addr
a network, the ne
equipment will n
to determine the I
camera needs Po
then cursor over t
o work properly, t
ust know the gate
e tester, cursor to
s, mask and gatew
o enter. To test for
(the IP camera is
e tester’s PSE IN j
displayed on the te
ent. Choose “start
ss is occupied, if t
IP address mus
t work properly.
address of an IP c
, connect the PoE
Start. Press
e tester must be
ay address of the
Set IP”, press
y address.
PoE, the IP camer
hat triggers the P
ck. Then connect t
ter screen.
, and
e
not be
he Link
mera.
into the
. If the
camera
. Use
and
E
he IP
21
N
ete
U
3
C
orapP
d
u
r
T
n
t
e
C
(
t
c
h
h
a
l
o
e
o
c
2
R
a
i
a
u
a
p
s
.
k
o
h
t
l
b
IP/C
TV Tester Us
r’s Manual
ote: PoE power s
t
ster’s PSE IN po
ster’s LAN jack.
TP/SCAN jack.
.3.15 Data mo
onnect the device
t
enter. Press
te of the device b
rotocol being sent,
ress to stop
isplayed .
pply equipment
t so it can power
Warning: Do not
his will damage t
itor
o the tester using t
to set the b
ing analyzed. Data
the tester will disp
the transfer. PTZ c
PoE switch, PSE
he IP camera or
onnect POE swit
e tester.
e RS485 or RS23
ud rate of RS485/
transfer will start
ay it in the upper r
ntrol codes from
power supply) m
ther devices that
hes or power sup
ports. Press
S232 port. The te
utomatically. If the
ght (“P: Pelco D”)
joystick, DVR or
st be connected t
re plugged into t
lies port to the
to select
ter must match the
tester can interpre
If not, “P:---“ wil
eyboard can also
the
e
, press .
baud
the
display.
e
22
3
P
p
3
P
Pto
Atu
KLB
A
u
l
d
e
m
o
L
t
/
C
s
e
u
d
a
S
t
e
0
g
g
a
m
n
a
IP/C
TV Tester Us
r’s Manual
.3.16 Time set
ress to se
Note：Press
hotographs and vi
.3.17 Device (t
ress to
ress or
quit.
uto power off: Set
rn off this feature.
eypad tone: Turn
anguage： ENG
rightness: Setting
ddress search: off
p
ect , press
to adjust
eo is based on this
ster) setup
enu , pres
to choose the it
the time of auto sh
n or off the keypa
ISH/ CHINESE
he brightness of O
on Open or close
to enter.
the time. Press
time setting.
to enter.
m, press
t-down. 5,10,…,6
beep feature.
nd other langua
D menu and back
he PTZ address se
to save. The ti
to adjust, press
minutes (of no ac
es
round.(0~7)
rch Menu.
e stamp used to
to save, press
tivity). Select “Dis
ame
ble” to
23
R
Fse
F
3
P
3
P
a
t
r
t
r
d
A
m
c
C
a
t
o
p
V
a
e
e
e
o
V
u
D
i
h
s
h
T
g
l
IP/C
TV Tester Us
r’s Manual
estore factory set
1 user-defined sho
elect, press
2 user-defined sho
.3.18 USB
hotographs and vi
.4 DC12V 1
ower a CCTV ca
c
amera when there i
ing: restore the d
tcut key (softkey):
o save. The defaul
tcut key (softkey).
eo files can be upl
power out
era with the DC12
s no power supply
ta of the factory.
Define this key to
setting is “ PTZ c
Adjust as above. T
aded to a Window
ut for CCT
(1A) power outp
vailable.
xecute any menu
ntroller”.
e default setting i
s computer using t
cameras
t from the tester. P
tem. Press
“Device setting”.
e USB jack.
erfect for powerin
to
the
Notice
. Do not conne
t any power sourc
into the tester’s “
24
C12/1A OUTPU
” port. Damage wi
l occur.
bcd
3
T
3
U
T
4
4
t
T
r
h
L
P
l
a
C
w
m
g
n
u
O
l
/
h
n
n
e
T
e
p
s
c
r
t
.
j
o
g
2
r
IP/C
TV Tester Us
r’s Manual
. Only connect
. When the CC
. For best perfo
.5 Audio inp
est the audio from
.6 LED flas
se the ultrabright
urn on the tester.
he DC12V/1A po
V camera draws
mance, fully char
ut test
audio devices. Co
light
ED lamp to light
ress to turn
er output to a CC
ore than 1A, the t
e the tester before
nect the audio devi
p the work space (
n/Off the LED.
V camera.
ster enters a protec
owering a camera
ce to the Audio In
ee the front panel
ion mode.
ack .
f the tester).
Note: Bright
、Specific
.1 General S
Video Test
Signal mode
Display
LCD adjustment
Video IN/OUT
ight can be harmfu
tions
pecifications
NTSC
3.5 inc
Bright
1 chan
. Do not look dire
PAL (Auto detect)
digital TFT-LCD
ess, Contrast, Satu
el BNC Input & 1
25
tly into the LED li
,480（RGB）x 3
ation adjustable
channel Output
ht.
0 resolution
IP/CCTV Tester User’s Manual
Video Output Mode 1.0 Vp-p
Video Level test
Level test Video signals measured in IRE (NTSC) or mV (PAL)
PTZ controller
Communication Supports RS232 and RS485
PTZ Protocol
Baud Rate
Video Signal Generation
Color bar generator
UTP Cable tester
UTP cable test
DC12V 1A power output
DC12V power output
(CCTV camera)
Audio input test
Audio input test Test the audio devices using the Audio I n port.
RS485 data analysis
Data Monitor Captures and analyzes the command data from controlling devices.
10x Zoom CCTV Image
Compatible with more than 30 protocols such as PELCO-D/P,
Samsung, Panasonic, Lilin, Yaan, etc.
600，1200，2400，4800，9600，19200,57600,115200bps
Outputs one channel PAL/NTSC color bar video signal for the testing
of monitors or a cable’s red, green ,blue, white or black color channel.
Using a Remote Adapter (included), test a CAT5/6 UTP cable. The
pinout is displayed.
Output DC12V (1A) power for powering a CCTVcamera
Image 10x zoom Zoom CCTV image display and video out signal.
Photograph、Video record, Record playback
Photograph Save the CCTV image as JPG file on mini SD card (included).
Video record Record CCTV videos and store them on mini SD card (included)
Record playback View the stored photographs and video from the mini SD card.
26
IP/CCTV Tester User’s Manual
Port flicker
Port flicker Blink the link LED on a switch port to locate a cable’s port location.
IP scan、Link monitor、PING test
IP scan Determine an IP camera’s IP address (must be on same network).
Link monitor Detect IP devices on the network (check for available IP addresses).
Search for IP cameras or other device s by scanning for their addresses
PING testing
PoE tester
PoE tester Display PoE power supply voltage and cable pairs used
POWER
Power Adapter
Battery Built-in 3.7V Lithium polymer battery. 3000mAh.
Rechargeable Charge time is 3-4 hours. Wor king time is 11 hours.
Low Consumption Energy saving technology, the battery icon real-time display
Setup parameters
on the network. When roundtrip time of the communication is
displayed.
DC 5V（1.5A）
Language English/Chinese and other languages OSD menu
Auto off Adjustable 5-60 (mins) or disable.
Keystroke tone On/Off
General
Working Temperature
Working Humidity
Dimension/Weight 194mm x 112mm x 48mm / 540g
-10℃ ～+50℃
30%～ 90%
27
Test Equipment Depot - 800.517.8431
99 Washington Street, Melrose, MA 02176
TestEquipmentDepot.com
Loading...