Byron W-251i Installation and Operation Instruction

Door Chime
• Remove the front cover.
• Insert 3 x 1.5volt alkaline batteries (“C”, UM2 & LR14
- not included) into the battery compartment, ensuring the battery polarity match the internal markings.
• Snap the front cover back on then it is ready to use. IMPORTANT: Not to be used with a transformer.
UM2
R14 “C”
UM2
R14 “C”
UM2
R14 “C”
UM2
R14 “C”
UM2
R14 “C”
UM2
R14 “C
Wired Door Chime with Light W-251i
Wired Door Chime with Light W-251i
75m
6
Byron No.W251 Size: A4 Date: 10 Nov 2007
Digital Code Set Up
• Press the Wired Push Button once, the Wired Chime unit will sound and it will generate a new operation code randomly and send a wireless signal to the Wireless Chime unit.
• The Wireless Chime unit will sound to indicate that new operation code is registered and memorised.
4
Wired Door Chime Wire Installation
• Run a length of bell wire from the bell push terminals to the location you wish to mount your chime.
• Split the wires and bare the end of the wire.
• Connect the wire to the terminal block in the top right corner of the chime.
• Push down the brown tab on the top of the terminal by a small, flat screwdriver.
• Whilst the tab is pressed down, insert your bell wire.
• One wire into the blue terminal, the other wire into the red terminal.
2
Important
1. Do not mount the Chime unit close to fireplace or expose to high temperatures.
2. Do not expose the Chime unit to direct sunlight or moisture
3. Always use alkaline battery. Please dispose of old, defective batteries in an environmentally friendly manner in accordance with the relevant legislation.
4. Make sure that no naked flame sources, such as lighted candles, should be placed on the unit.
5. The unit should not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the unit.
6. CAUTION: Replace only with the same or equivalent type of battery that is recommended by the manufacturer.
7. CAUTION: Make sure batteries are installed correctly as per the internal markings.
8. CAUTION: Danger of explosion if battery is incorrectly installed or replaced.
9. IMPORTANT: There are no serviceable parts in the units, do not attempt to repair it.
User Hints
If the door chime unit does not sound, please check the followings: a) Flat batteries in either Wired or Wireless Chime units - change the batteries. b) Wrong battery polarity in either Wired or Wireless Chime units - re-insert the batteries. c) Wired and Wireless Chime units are not on the same operation codes - re-set the code
(see digital code set up).
d) Units are out of range - Operate the Chime unit within the operation range.
Specification
Operating Temperature: -10C - +40C Operating Distance : 75metre (245ft approx. - in open field & at suitable condition) Selectable Digital Code: Total two hundred fifty six (256) possible digital codes
“Type R2 Device - device where the sound output is created by the initial operation of the control and where the period of sound output continues for the designed duration irrespective of condition of the control.”
433MHz
R&TTE
APPROVED
CH Byron Electrical United Kingdom. www.chbyron.com
CH Byron Electrical Ltd Byron House 34 Sherwood Rd, Astonfield Bromsgrove, B60 3DR UK Tel: 0845 2301231 e: support@chbyron.com w: www.chbyron.com
Door Chime unit
Power: 3 x 1.5volt alkaline batteries (“C”, UM2 & R14 - not included)
Wired Door Chime Wire Installation
1. Run a length of bell wire from the bell push terminals to the location you wish to mount your chime.
2. Split the wires and bare the end of the wire
3. Connect the wire to the terminal block in the top right corner of the chime.
4. Push down the brown tab on the top of the terminal by a small, flat screwdriver.
5. Whilst the tab is pressed down, insert your bell wire.
6. One wire into the blue terminal, the other wire into the red terminal.
Operate With A Byron SX Range Wireless Door Chime
The Chime unit can be operated with the Byron SX Range Wireless Door Chime. When the wired chime unit is activated, it sends a wireless signal to your Wireless Door Chime that activates the chime to sound, with the operation range up to 75m (245ft approx. - in open field & at suitable condition). Read the following instructions before use.
Digital Code Set Up The Chime unit is equipped with an advanced random and self-learning operation coding ability therefore no setting is needed. Read the following instructions before use.
1. First time operation: After battery installation on both Wired and Wireless Chime units, press the wired Push Button once, the Wired Chime unit will sound and it will generate a new operation code randomly and send a wireless signal to the Wireless Chime unit. The Wireless Chime unit will sound to indicate that a new operation code is registered and memorised.
2. Interference from a similar unit operating nearby: a) Simply remove the batteries from both Wired and Wireless Chime units and rest for
10 seconds, this will erase the memory.
a) Insert the batteries into the Wired and Wireless Chime units. Press the wired Push
Button once, the Wired Chime unit is sound and it will generate a new operation code randomly and send a wireless signal to the Wireless Chime and it will sound to indicate that new operation code is registered and memorised.
Melody Selection - Wireless Door Chime
Press the melody selector once to select a melody as your wireless door chime sound, there is a total of 8 melodies for selection.
Melody Selection
• Press the melody selector once to select a melody as your Byron SX range Wireless door chime sound, there is a total 8 melodies for selection.
5
UM2
R14 “C”
UM2
R14 “C”
UM2
R14 “C”
Melody Selector
Door Chime Installation
• Drill a hole, fit a wall plug and screw.
• Leave a gap of 3mm between the screw head and wall.
• Locate the keyhole slot on the back of the chime unit over the screw.
3
3mm
Operation
• Press the wired Push Button once, the wired chime unit is activated and sound, it also sends a wirless signal to your Wireless Door Chime, and your door chime will sound.
• Operate the Wireless Door Chime unit within the operation range up 75m (245ft approx. - in open field & at suitable condition), test it before final installation.
Flashing Light
Operate With Byron SX Range Wireless Door Chime
Operate With Byron SX Range Wireless Door ChimeOperate With Byron SX Range
Wireless Door Chime
Loading...