Byron MP001 Quick User Manual

MP3 Downloadable

Wire Free Chime Kit

™

4

1: Press the Bell Push to
confirm the setup

2: The Chime will play the
melody and the alert light will
flash.

4

2

1: Place a small flat screwdriver
into the locking clip on the
base of the Bell Push.

2: Gently twist.

3: The backing plate will unclip.

1

™

1: Push Button 6: Portable Chime
2: Melody Selector 7: Speaker
3: Bell Push Battery 8: Volume Control
4: Signal Sent LED 9: LED Alert
5: USB Lead 10: USB Input

MP001

™

:3

1:

4:

10:

8:

9:

5:

6:

2:

3

1: Remove the battery cover.

2: Insert 3 X 1.5V Size ‘AA’
batteries (Not Supplied).

3: Make sure the
Positive/Negative terminals
match the internal markings

4: switch the Chime ON

5: Replace the battery cover.

1: Insert CR2032 battery
(Supplied) into the battery
holder.

2: Make sure the positive side
is facing upwards.

3: Replace back plate.

Warning: Make sure that the batteries are
replaced correctly to avoid battery failure.
Only replace with same or equivalent type.

3

Downloading MP3 Melody:

Functions:

To select the Chime Volume
level, press the ‘+’ button
increase the volume and ‘-’
button to decrease the volume.

To select a melody for the Door Chime

1: Select between preprogrammed (IN) or
downloaded MP3 melodies (MP3).

2: Press the arrows on the door
chime to select the next melody

3: The chime will play the newly selected
melody

4: Press the centre button to confirm
Or press arrows to select the next
melody.

1: Connect the chime to the
USB port of a computer using
the USB lead (supplied ).

PC Only
2: The Chime will appear as a USB
storage device, install and run MP3
Editor.exe file on your computer.

MP3 Music

Look in:

Open

MP3 File(*.mp3)

File Name:

Files of Type:

Open

Cancel

Melody File 1

Melody File 2

Melody File 3

Melody File 4

3: Select the open file icon ,
highlight the required MP3 file on
your PC and click Open.

5: Edit the file length by inputting the required start and end times.
Use the Play/Pause button to listen to the mp3 file, recommended file
length is between 8-10sec.

5: Press the scissors icon to Cut and save the MP3 file, the
recommended file length is approximately 8-10 seconds long.

Melody File 1 Melody File 2 Melody File 3

Back Search Folders

E:\

Address

PC & Mac
6: Drag and drop the edited file onto the MP3 Chime, the file will be
saved on to the MP3 chimes internal memory.

00:00.0 / 00:00.0

00Start Time

End Time

00

00 00 0

0::.

.

Reset

Rewind Fast

Forward

Play

Volume

Stop

Press to Cut

4: Highlight the MP3 file in the tunes list and press PLAY.

Video Tutorial:

View or video tutorial saved on the MP3 chime or via our
YouTube channel.
http://www.youtube.com/user/CHByron

Installation Guide:

Portable Door Chime: MP001/HB702
Power: 3 x ‘AA’/LR6 1.5V Batteries
(Not supplied)
Range: 100 Metres
Indoor Use Only

Bell Push: MPT
Power: 1 x 23A 12V DC Battery
(Included)
IP44 Weather Resistant

Specification

Range Guide

433.92MHz

R&TTE

APPROVED

CH Byron Electrical United Kingdom. www.chbyron.com

A

B
DK
FIN

F

D
GR

LT

IRL

I

L

NL

P
E
S

UK
BG
CZ

EST

H
IS

LV

M
N

SK
SLO
CH

PL
RO

Project Manager

Mr G Hunter

GB: CH Byron
Byron House, Sherwood Rd
Astonfields, Bromsgrove
B60 3DR
UK

[e-mail]

9-5 Mon-Fri, Local call charges apply

V1.0

Tel: [phone] (UK)

www.chbyron.com

Avoid locating the Bell Push/Chime on or directly
near metallic surfaces as this may reduce the
operation range.
UPVC Door Frames:
When locating the bell push onto a UPVC door,
always check the operating performance before final

installation, internal metal frame may affect
performance.
Tip: Try adjusting the location of the Bell Push to the Left/Right
or place on external wall.

Installation Guide: Bell Push

Installation Guide: Chime

Place the door Chime within the operating range,
transmission of the wire free signal through
Walls, Doors and Ceilings etc, may reduce the operating
range. Chime unit for INDOOR use only.

Diagram for illustration purposes only

1

2

‘CLICK’

1: Using back plate as a
template.

2: Making sure UP arrow
points UP.

2: Mark and drill holes.

3: Insert wall plugs and attach
to wall using screws
provided.

4: Clip the Bell Push on to the
back plate making sure the
Bell Push ‘Clicks’ in to
place.

Tip: The Bell Push can be
installed using a suitable
double sided adhesive tab or
tape when drilling is not
sutiable.

3

User Hints:
In case of the door chime does not sound, please check the
followings:
a) Flat batteries in either Push Button or Door Chime.
b) Wrong battery polarity in either Push Button or Door Chime.
c) For Plug-in Door Chimes make sure the socket is switched on.
d) Bell Push and Door Chime are not paired together, see setup
guide.
e) Materials in between the Bell Push & Chime will reduce the
operating range, move the Door Chime closer to the Bell Push
f) Wire free devices can be affected by external sources e.g. wire
free home alarms or power transformers/adapter

Chime Unit
1: Remove old Batteries.

2: Insert new batteries, 3 X 1.5V
size ‘AA’.

3: Make sure ‘+/-’ match the
internal markings.

4: Test Chime Kit.

Changing Batteries:

Bell Push:
1: Remove back plate from the
Bell Push.

2: Remove old battery

3: Replace with new ‘23A’ 12V
battery.

4: Insert into holder making sure
‘+/-’ match the internal
marking

5: Test Chime Kit.

Always dispose of old batteries in an
environmentally friendly way.

Type R2 Device - device where the sound output is created by the initial
operation of the control and where the period of sound output continues
for the designed duration irrespective of condition of the control.

IMPORTANT:

There are no serviceable parts, do not repair.

The appliance is not to be used by children or persons with

reduced physical, sensory or mental capabilities, or lack of experience and knowledge,unless they have been
given supervision or instruction. Children should be supervised to ensure that they do not play with the
appliance.

Address Code:

The MP3 Door Chime, comes preset to a default address code, this
code may need to be changed if the chime rings due to a
neighbouring door chime or similar wire free product.

1: Select a new address code in the bell
push, by randomly moving the white
dip-switch’s.

2: Copy the new address onto the
chimes dip-switch’s. Located in the
battery compartment of the chime.

3: Test the chime kit by pressing the
bell push.

1 65432

ON Dip

1 65432

ON Dip

e.g.