Byron Home Easy HE-414 Installation Instructions Manual
RE-INVENTING THE HOME
HOME
easy
HE-414
Remote Control Outdoor
V1.0
OFF: An additional safety feature of the HE410 is the ability to switch off the
power as per a normal socket.
INSTALLATION WARNING:
ON INSTALLATION TURN OFF YOUR
MAINS ELECTRIC SUPPLY
This product should be fitted by a competent
person in accordance with the instructions listed
below and with the relavent clauses of the IEE
wiring regulations BS7671.
The outdoor socket should be used in
conjunction with a fused spur connection, all
connections to the socket need to be made as
instructed, making sure that the cable used is
appropriate for the installation environment, free
from stress & terminals are tightened fully.
1. Open up the front, flip top cover.
2. Unscrew the four screws shown. To
separate the front, from the back of the
unit.
3. After all 4 screws have
been removed; the front will
separate from the back.
Front half
Back half
Opening Unit:
2. Using the back half of the unit as a template, pencil mark all four
corners onto your chosen surface. Making sure 'TOP' (marked on
the casing is at the top.
3. Drill all four marked holes and insert suitable wall plugs for a
number ‘8’ screw (recommended size).
4. Screw to the wall.
Fixing Holes
Mounting Socket:
1: In the back half of the unit, in all four corners are purpose made holes for fixing your
remote socket to your intended surface. The outdoor socket needs to be mounted
onto a flat, vertical surface. Free from grease, loose material and any corrosive
substances. We recommend a house or sturdy garden wall.
Remove Bottom
'Entry Blank'
Wiring Remote Socket:
On the back half of the remote socket you will see that there are 4 circular shaped
disks (‘Entry blanks’) on each side (3 are plastic, 1 is rubber). Depending on if you wish
to link up more than one ‘Outdoor remote socket’ you can remove or replace these
disks.
It is recommended that the bottom most 'Entry blank' should be removed to gain entry
into the 'Outdoor Remote Socket'. This will help keep the moisture out.
If installing the Outdoor socket with conduit from the sides or top attachment, a 5mm
hole must be drilled through the bottom left drainage hole. This will allow for any
condensation forming in the conduit, to drain out.
Caution: opening the drainage hole will affect the IP rating of the product. Ensure that
jetted water is not directly sprayed onto the unit.
Do Not drill out the drainage hole when installing the
Outdoor socket into a dusty environment. Always install
the unit via the bottom cable entry, making sure that a
5mm hole is drilled into the lowest point in the conduit
system.
1. Switch off and isolate the mains power before altering
the code setting
4. Send the cable through the conduit
and into the ‘Outdoor Remote Socket’.
(Live - Brown)
(Earth - Green & Yellow)
(Neutral - Blue)
Exposed wire
(L = Live - Brown)
(E = Earth - Green & Yellow)
(N = Neutral - Blue)
LEN
(FIG.8)
LEN
Please Note: The Cable is
up inside the box, so that
no wires can be seen.
2.
2: Cut back the cable to reveal 3 separate wires
L= Live Brown
E= Earth Green & Yellow
N= Neutral Blue
3. Now strip each wire, exposing 10mm of its
3: Insert the exposed core wires into their related
terminals and clamp down by tightening the
respective screw.
L= Live Brown
E= Earth Green & Yellow
N= Neutral Blue
When installing secondary Outdoor receiver sockets always place them
the units approximately 30-40cm apart.
Installation:
1. Fist select your required location, it's recommended that the PIR is installed
approximately 3 metres off the ground (ideally under the eaves of the building) and,
away form direct sources of sunlight and heat.
Warning: Avoid installing the Remote Control PIR onto metallic surfaces
and above heating vents as this will affect the operating performance.
Avoid Direct Heat
Sources
Detection Distance
The HE-414 allows you to control your HomeEasy outdoor
socket via a wire free remote control PIR sensor. When the
PIR beam is broken the outdoor PIR will switch on your
Remote control sockets for between 15 seconds and
4 Minutes.
AUTO: Allows the Remote Control PIR to switch
on/off the outdoor socket.
ON: Sets the Outdoor socket as a standard outdoor socket.
USE THIS OPTION WHEN USING GARDEN
MACHINERY SUCH AS A LAWNMOWER OR HEDGE CUTTERS.
C H Byron
34, Sherwood Rd
Aston Fields
Bromsgrove
B60 3DR
Contact Details:
433MHz
R&TTE
APPROVED
CH Byron Electrical United Kingdom. www.chbyron.com
A
B
DK
FIN
F
D
GR
LT
IRL
I
L
NL
P
E
S
UK
BG
CZ
EST
H
IS
LV
M
N
SK
SLO
CH
PL
RO
0560
Tel: 0845 2301231
Fax: 01527 557701
Web: www.chbyron.com
E-mail:
support@chbyron.com
Contact: Helpline: 0845 2301 231
WARNING:
You MUST install an earth cable between the origin of the installation and the earth
terminal of the outdoor socket. This must be insulated inside a sleeve protector within
the conduit.
If using metal conduit, earth continuity must be maintained between conduits. Seal
Conduit and conduit entry with a non setting conduit sealant. Purchasable form you
local electrical retailer.
Remote Socket reset:
To delete all the remote control units from the memory of the receiver socket,
hold the "Learn" button for more than 6 seconds, the LED will start to blink
continuously. Press the learn button again, the LED will blink twice to confirm
the deletion of all remote controls form the receiver memory.
Product Specification:
Remote Control: Receiver HE-410
Input: 230V ~50Hz
Range: 30 Metres (Open Distance)
Frequency: 433.92MHz
Max Load: 3000W (Resistive)
IP56 (Lid Clip closed)
Warning: Never Exceed the Product Specification
To pair the outdoor PIR with a receiver unit, remove the
battery cover and, slide the switch to DEL.
if required select a new group or unit code
(using additional PIR units).
Deleting Remote Control:
To delete the PIR from the memory of a HomeEasy receiver socket or module,
simply press the "Learn" button. The LED will start to blink; slide the "LEARN"
switch to "DEL",, the LED will blink twice to confirm that the remote control has
been removed from the receiver sockets memory.
Pairing/Deleting with Remote Control:
Up to Six remote control units can be paired with each HomeEasy Receiver
socket or module, press the "Learn" button . The LED will start to flash, now
slide the "LEARN" switch to "SET", the units are now paired together.
Detection Area:
Remote Control PIR: HE-403
Battery: 3 * AAA
Range: 25Metres (Open Distance)
Frequency: 433.92MHz
IP44 Weather Proof
Setting Timer :
The HomeEasy Outdoor PIR will active for
a predefined period of time when
activated, this can be set between 15
seconds and 4 minutes.
To select the time period, remove the
battery cover and using a small screw
driver rotate the dial to select the
required time.
Timer Setting:
1min:
15 sec:4 min(max):
The PIR detection area is 110 degrees, this can be reduced using the clip-on
covers (included). if required the covers can be cut to size.
if r
equ
i
r
ed the c
o
v
er
s c
an be cut t
o s
i
z
e
.
N/A:
Day/Night Setting:
The PIR can operate 24Hrs a day orat night night (Low Level Conditions
<10Lux). To select night only mode, remove the cover from the bottom of the
PIR and press the "LUX" button as shown below.
RF Range: The radio signals operating distance is reduced when the signal has
to pass through walls. The radio signals achieve a range of 25m; this can be
reduced depending on the type of material.
No Activ
a
tion:
-C
heck the ba
tt
ery lif
e and pair
ing with r
ec
eiv
er so
ck
et or
mo
dule.
Rec
eiv
er sta
ys ON -T
he PIR migh
t b
e r
ec
eiving false signals due
t
o the
con
tinuously
:
selec
t
ed lo
c
a
tion,
tr
y adjusting the angle
.
R
adom A
c
tiv
a
tion: -W
ind/rain c
an c
ause the PIR unit t
o ac
tiv
a
t
e , try a new
lo
c
a
tion if needed
.
-S
mall animals can ac
tiv
a
t
e the PIR.
-T
ry selec
ting a new addr
ess c
o
de
.
-Passing traffic or p
edestr
ian c
an ac
tiv
a
t
e the PIR, alt
er
the det
ec
tion angle
.
H
elp S
ec
tion :
2. Remove the PIR unit form the base and using the mounting bracket as a
template mark and drill appropriate holes and fix the bracket securely using
the appropriate screws and wall plugs (included).
1. Unclip the battery cover from the bottom of the
PIR using a small screw driver.
Changing Batteries:
2. Remove the batteries and replace using 3
new 'AAA' batteries, making sure the polarity
is correct.
Always dispose of old batteries in a
environmentally responsible way
3. Replace the battery cover making sure the rubber seal is correctly
aligned and firmly push the case together.
Rubber seal
Loading...