Byron Home Easy HE-225 Installation Instructions Manual
G
I
K
+
_
The HE-200 Remote Control Timer can be paired to 16
separate receiver units, select the unit code by pressing
the unit button.
Up to Six remote control units can be paired with each receiver socket or
module. To program a socket insert the unit into a plug socket and switch on
the power, now press "Learn" button . The LED will start to flash, now press
the selected "ON" button on the remote control, the LED will stop flashing.
The units are now paired together, you can test this by pressing the selected
"ON/OFF" button
Always refer to the original instruction when using with additional products
Deleting Remote Control:
To delete a remote control that has been paired with a HomeEasy receiver
socket, simply press a "Learn" button. The LED will start to blink; press the "Off"
button on the remote control, the LED will blink twice to confirm that the
remote control has been removed from the receiver sockets memory.
Remote Socket reset:
To delete all the remote control units from the memory of the receiver socket,
hold the "Learn" button for more than 6 seconds, the LED will start to blink
continuously. Press the learn button again, the LED will blink twice to confirm
the deletion of all remote controls form the receiver memory.
Unit Setting:
Pairing/Deleting with Remote Control:
The HE-200 comes with a preset to Group code A. When
using additional remote control timers you will need to
select a new group code.
To select a new group code, remove the battery cover and
using a small screw driver, rotate the group dial to a new
setting e.g. Group B
Dimming Receiver Sockets HE220:
To dim a compatible receiver socket.
RE-INVENTING THE HOME
HOME
easy
1. Select the unit by
pressing the "unit"
button until the
correct number is
displayed on the
screen.
2. Press the "On" button and
then press "On" again.
Never exceed maximum
load.
HE202 Dimmer Socket:
300W
HE202 Dimmer Socket:
100W
3. The dimmer will start to dim the light unit till it reaches zero, then the
unit will start to increase the light up to the maximum level. To set the
desired level, press the "On" button.
4. Press the "Off" button to switch the receiver unit off.
Remove the battery cover form the back of the remote control.
The HE-200 includes 2 batteries:
LCD Display: 1 x CR2032 -Byron SX100 (Included)
RF Transmission: 1 x 23A - Byron SD100 (Included)
Remove the required battery and replace with new, making sure the
polarity matches the internal markings.
HE-225 Remote Control
Timer Kit
V1.0
Display Functions:
Product Specification:
Remote Control: HE-200
Battery: 3v Cr2032 & 12V 23A
Range: 30 Metres (Open Distance)
Frequency: 433.92MHz
Indoor Use Only
Warning: Never Exceed the Product Specification
Receiver Socket:
HE-202: Dimmer Socket
Input: 230V ~ 50Hz
Max Load: 300W (Incandescent)
Frequency: 433.92MHz
Indoor Use Only
The HomeEasy remote control Timer allows you to add
the following extra features to your HomeEasy products:
LCD Display
Functions:
1: 12 Programmable Memory Spaces
2: 24Hr Time
3: Timer Setting "On"
4: Timer Setting "Off"
5: Security Mode
6: Timer Mode - Single Timer Setting
7: Timer Mode - Daily Timer Setting
8: Low Battery Warning
9: Unit Code Display
10: Transmission Indicator Signal
Receiver Select
Switch "On" Selected Receiver
Switch "Off" Selected Receiver
Clock Setting
Program Timer/View
Enter
Delete/Pause
Select Up/Down
easy
HOME
Changing Batteries:
-12 Programmable memory Settings
-Security Mode
-Single and Daily Timer Functions
-24Hr Timer Display
-30 Metre Wire Free Range
-CR2032/23A Battery (Included)
easy
HOME
300W Dimmer300W Dimmer300W Dimmer
easy
HOME
300W Dimmer300W Dimmer300W Dimmer
Learn Button
C H Byron
34, S herwood Rd
Aston Fields
Bromsgrove
B60 3DR
Contact Details :
433MHz
R&TTE
APPROVED
CH Byron Electrical United Kingdom. www.chbyron.com
A
B
DK
FIN
F
D
GR
LT
IRL
I
L
NL
P
E
S
UK
BG
CZ
EST
H
IS
LV
M
N
SK
SLO
CH
PL
RO
0560
Tel: 0845 2301231
Fax: 01527 557701
Web: www.chbyron.com
E-mail:
support@chbyron.com
Help: Occasionally interference from receiver sockets plugged into adjacent wall
sockets or when used with transformers (low voltage products) can affect the
operating range.
Try placing one of the receiver sockets in another wall socket. For low voltage
products, place the transformer as far away form the receiver socket as possible.
Contact: Helpline: 0845 2301 231
TIMBER
CONCRETE
METAL
GLASS
PLASTICS
RF Range: The radio signals operating distance is reduced when the signal has
to pass through walls. The radio signals achieve a range of 30m inside a building;
this can be reduced depending on the type of material
10 - 15%
BRICK
10 - 40%
40- 80%
10 - 40%
90%
5 - 15%
Range
Reduction Guide:
Switching On/Off :
1. Select the unit by
pressing the "unit"
button until the
correct number is
displayed on the
screen.
2. Press the "On"
button, the receiver
socket will switch on.
Never exceed the
maximum load.
3. Press the "Off" button to switch the receiver unit off.
Setting Clock
The remote control displays the time in a 24hr format, to set the time.
1. Press and hold the
clock button for +3sec.
The hrs will now start
to flash
2. Use the
buttons to select
the hours and
press Enter.
3. The minutes will now start to flash, set using the up and
down arrows and press
Setting Timer :
The HE-200 remote control timer can store unto 12 different timer
programs, ideal for switching on lights thought the home for added
security.
To program the remote control:
1. Press and hold the "Timer" button for 3 seconds, the
display will show the 12 available memory spaces. Use
the arrows keys to select a memory space, the display
will also show any programmed times already saved.
Press "Enter" to select the program space.
2. Press and hold the "Timer" button for 3 seconds, the
display will show the 12 available memory spaces. Use
the arrows keys to select a memory space, the display
will also show any programmed times already saved.
Press "Enter" to select the program space.
3. The start or On time will start to flash, use the arrows keys to select the hours
and press enter to select the min.
Now select the finish or off time.
4. Finally select the program mode using the arrows keys and press enter to
confirm.
Daily Timer Setting: Activates the program daily
Security Setting: Selecting the security mode will switch the
receiver units "On/Off" randomly through out the set time.
On = between 40Min - 2Hrs
Off = between 40Min - 3Hrs
Single Timer: Activates the program for a single time only.
Help Section :
Product Specification:
Receiver Socket:
HE-205: Bulb Holder
Input: 230V ~ 50Hz
Max Load: 100W (Incandescent)
Frequency: 433.92MHz
Indoor Use Only
Loading...