Byron Home Easy HE-207 Installation Instructions Manual

RE-INVENTING THE HOME

HOME

easy

HE-207 Remote control

Indoor PIR Kit

V1.0

Installation:

The HE-207 Indoor PIR adds extra
security and ease of use to your Home
Easy products

The HE-207 allows you to control your HE205 Bulb Holder via a wire free
PIR sensor. When the PIR beam is broken the indoor PIR will switch on the light
for 5 seconds to 10 minutes
Compatible with all Home Easy products.

The HomeEasy Indoor PIR can be placed in any location, even in bathrooms.
Only use the adhesive strip on suitable surfaces.
Avoid placing the PIR in direct sunshine, above direct heat sources or on
metallic surfaces.

Detection Area

Detection Range:

The Indoor PIR has 3 selectable detection ranges: 1, 3 or 6 Metres.
To alter the detection range, remove the front cover and move the slide switch
to the required setting.

3. Replace the two front covers.

2. The base unit can be attached to the wall using either the adhesive strips or

screws (Included).

1. Using a small screwdriver remove the front cover and base plate.

-Selectable timer setting

-Selectable Detection Range

-Variable Light setting

-25 Metre Wire Free Range

-Battery Powered 2*AAA

-100W Max Load
(Incandescent Lights only)

Learn

Up to Six remote control units can be paired with each
HomeEasy Receiver socket or module, to pair the indoor
PIR with a receiver unit, remove the front cover and,
slide the switch to DEL.

Deleting Remote Control:

To delete the PIR from the memory of a HomeEasy receiver socket or module
control. Simply press the "Learn" button, the LED will start to blink; slide the
"LEARN" switch to "DEL", the LED will blink twice to confirm that the remote
control has been removed from the receiver sockets memory.

Pairing/Deleting with Remote Control:

Now press the "Learn" button, the LED will start to flash, then slide the
"LEARN" switch to "SET", the units are now paired together.

Resetting Remote Control:

To delete all the remote control units from the memory of the receiver
module, hold the "Learn" button for more than 6 seconds, the LED will start
to blink continuously. Press the learn button again, the LED will blink twice to
confirm the deletion of all remote controls from the receiver memory.

1.0

1 2 3 4 5 6 7 8

6M 6M 6M
3M 3M 3M
1M 1M 1M

Height (PIR)

Detection Range (Metres)

C H Byron
34, Sherwood Rd
Aston Fields
Bromsgrove
B60 3DR

Contact Details :

433MHz

R&TTE

APPROVED

CH Byron Electrical United Kingdom. www.chbyron.com

A

B
DK
FIN

F

D
GR

LT

IRL

I
L

NL

P
E
S

UK
BG
CZ
EST

H
IS

LV

M
N

SK
SLO
CH
PL
RO

0560

Tel: [phone]
Fax: [phone]
Web: www.chbyron.com
E-mail:
[e-mail]

Contact:   Helpline: 0845 2301 231

RF Range: The radio signals operating distance is reduced when the signal

has to pass through walls. The radio signals achieve a range of 25m; this can
be reduced depending on the type of material.

TIMBER

METAL

GLASS

PLASTICS

10 - 15%

BRICK

10 - 40%

CONCRETE

40- 80%

10 - 40%

90%

5 - 15%

Range

Reduction Guide:

H

elp S

ec

tion :

Day/Night Setting:

The PIR can operate one of three setting depending upon the ambient light
Level, to alter the light setting remove the front cover and use the slide switch
to select the setting.

PIR will operate 24Hrs a day

PIR will operate between 4pm to 6am

PIR will operate between 6pm to 6am

Times are approximations only

Changing Batteries:

1. Unclip the front cover from the front of the PIR
using a small screw driver.

2. Remove the batteries and replace using 2
new 'AAA' batteries, making sure the polarity
is correct.

Always dispose of old batteries in a
environmentally responsible way

3. Replace the front cover making sure the clips are correctly aligned and
firmly push the case together.

No Activation:   Check the battery level and polarity, replace with new
     batteries if necessary

Receiver Stays:   The PIR may be suffering from false activation, try
ON Continuously  adjusting the position and detection angle.

1Min

Setting Timer :

The HomeEasy indoor PIR will switch on the
receiver socket or module for a predefined
period of time, this can be set between 5seconds
and10 minutes.
To select the time period, remove the front cover
and slide the switch to the required timer
setting.

5Sec

5

10min

Product Specification:

Remote Control: HE-303
Battery: 2 * AAA
Range: 25Metres (Open Distance)
Frequency: 433.92MHz
Indoor Use Only

Receiver Module: HE-205
Input:230V ~50Hz
Range: 30 Metres (Open Distance)
Max Load: 100W (Incandescent)
Frequency: 433.92MHz
Indoor Use Only

Detection Angle:

The PIR detection area is 65 degrees, this can be reduced using the clip-on
covers (included). if required the covers can be cut to size.

if r

equ

i

r

ed the c

o

v

er

s c

an be cut t

o s

i

z

e

.

6M 6M 6M
3M 3M 3M
1M 1M 1M

1.5

1 2 3 4 5 6 7 8

Height (PIR)

Detection Range (Metres)