Byron BY30 User Manual
™
Additional
Bell Push
BY30
1: Push Button
2: Melody Selector - inside Bell Push
3: Bell Push Battery- inside Bell Push
4: Signal Sent LED
1:
2:
4:
:3
1: Place a small flat screwdriver
into the locking clip on the
base of the Bell Push
2: Gently twist
3: The backing plate will unclip
1
1: Insert CR2032 battery
(Supplied) into the battery
holder.
2: Make sure the positive side
is facing upwards.
3: Replace back plate.
2
Warning: Make sure that the batteries are
replaced correctly to avoid battery failure.
Only replace with same or equivalent type.
Chime With Volume Control
1: Press and hold the ‘VOL’
button on the Door Chime,
until the Chime goes
‘Beep Beep’ (6 Seconds)
2: Press the Bell Push within
60 seconds to learn the
Bell Push to the chime.
3: The Chime will ring to
confirm setup.
5
Beep
Beep
Note: Maximum of 6 Bell
Pushes can be learnt to a
single Chime.
3
Avoid locating the Bell Push/Chime on or directly near
metallic surfaces as this may reduce the operation
range.
UPVC Door Frames:
When locating the bell push onto a UPVC door, always
check the operating performance before final
installation, internal metal frame may affect
performance
.
Note: Try adjusting the location of the Bell Push to the Left/Right or
place on external wall.
4
‘CLICK’
1: Using back plate as a
template.
2: Making sure UP arrows
points UP.
2: Mark and drill holes.
3: Insert wall plugs and attach
to wall using screws
provided.
4: Clip the Bell Push on to the
back plate making sure the
Bell Push ‘Clicks’ in to
place.
Note: The Bell Push can be
installed using a suitable
double sided adhesive tab or
tape when drilling is not
sutiable.
Plug-in Chime:
Remove from socket and then
plug chime back-in
Portable Chimes:
Remove the batteries and
then reinsert the batteries
1: The Chime will ‘Beep Beep’.
2: Press the Bell Push within
60 seconds to learn the
Bell Push to the chime.
3: The Chime will ring to
confirm setup.
5
Beep
Beep
Note: Maximum of 2 Bell Pushes can be learnt to a single Chime for
Front/Back Door use.
Chime Without Volume Control
Changing Batteries:
Bell Push:
1: Remove back plate from the
Bell Push.
2: Remove old battery from the
holder.
3: Replace with new ‘CR2032’ 3V
battery.
4: Insert into holder making sure
‘+’ is facing up.
5: Test Chime Kit.
Specification
Bell Push: BY30
Power: 1 x CR2032 3V DC Battery
(Included)
IP44 Weather Resistant
Type R2 Device - device where the sound output is created by the
initial operation of the control and where the period of sound output
continues for the designed duration irrespective of condition of the
control.
IMPORTANT:
There are no serviceable parts, do not repair.
The appliance is not to be
used by children or persons with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,unless they have been
given supervision or instruction. Children should be supervised to ensure
that they do not play with the appliance.
CH Byron
Byron House, Sherwood Rd
Astonfields, Bromsgrove
B60 3DR
UK
support@chbyron.com
9-5 Mon-Fri, Local call charges apply
Tel: 0845 2301231 (UK)
www.chbyron.com
433.92MHz
R&TTE
APPROVED
CH Byron Electrical United Kingdom. www.chbyron.com
A
B
DK
FIN
F
D
GR
LT
IRL
I
L
NL
P
E
S
UK
BG
CZ
EST
H
IS
LV
M
N
SK
SLO
CH
PL
RO
Project Manager
Mr G Hunter
V1.0
A
B
DK
FIN
F
D
GR
IRL
I
L
NL
P
E
S
SK
PL
Loading...