|
DB306 Wire 75Metres |
|
|
™ |
|
|
|
Free Plug-through |
|
|
Chime Kit |
1 |
2 |
3 |
Using a small flat |
Insert the 23A battery |
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
||
screwdriver, insert into the |
(supplied) into the battery |
|
|
|
|
|
|
locking clip and gently |
holder, making sure the |
Insert the Plug-in Chime into a |
|||||
twist. The back plate will |
Positive/Negative terminals |
||||||
unclip from the Bell Push. |
match the internal |
standard 220-240V ~50Hz wall |
|||||
|
markings. Battery Comes |
socket and switch the socket ON, |
|||||
|
Preinstalled |
Chime will ring. |
|||||
4
Press the learn button (L) on the front of the Chime to enter the Learn mode.
The chime will ring to confirm.
5 |
6 |
Press the Bell Push within 30 seconds, the Chime will ring to confirm that the Bell Push has been paired to the Chime.
Test the Chime in the intended location, as internal walls and surfaces may reduce operating range. DO NOT mount onto metallic surfaces.
Plug in a standard plug e.g. Table light.
Max load: 1000W
Tel: 0845 2301231(UK) |
|
|
|
CH Byron |
9-5 Mon-Fri, Local call charges apply |
|
|
|
Byron House, Sherwood Rd |
|
|
|
Astonfields, Bromsgrove |
|
support@chbyron.com |
|
|
|
|
|
|
|
B60 3DR |
|
|
|
|
|
UK |
www.chbyron.com
Usage Guide:Avoid positioning the Bell Push/Chime on or directly near metallic surfaces as this may reduce the operation range.
UPVC Door Frames:
When positioning the bell push onto a UPVC door, always check the operating performance before final installation, internal metal frame of the door may affect performance.
Tip: Try adjusting the location of the Bell Push slightly to the Left/Right or place on external wall.
Note: the appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge,unless they have been given supervision or instruction. Children should be supervised to ensure that they do not play with the appliance.
|
Bell Push & Door Chime: |
|
1: Using back plate as template |
|
2: Making sure UP arrow points UP. |
|
3: Mark and drill holes. |
|
4: Insert wall plugs and attach to wall using screws |
|
provided. |
|
5: Clip the Bell Push on to the back plate making sure |
|
Bell Push ‘Clicks’ into place. |
|
6: Place the Door Chime within the operating range (75M). |
|
Transmission of the wire free signal through Walls, Doors |
|
and Ceilings etc, may reduce the operating range. |
|
The Chime is designed for INDOOR use only. |
Melody |
Resetting |
Selection: |
Chime: |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
To select a new melody for the Door Chime |
To reset the chime and delete the bell push |
|||||||||||||||
1:Press the Melody Select button on the |
learnt to the chime |
|||||||||||||||
front of the Chime unit (M). |
|
1:Press and hold the Learn button (L) until |
||||||||||||||
2:The Chime will play the newly selected |
the Chime plays a melody - approximately |
|||||||||||||||
melody. |
|
6 seconds. |
||||||||||||||
3:Press again to select the next melody. |
2:The Chime has been reset |
|||||||||||||||
|
|
|
|
|
|
|
|
- see Points 4 & 5 to pair Bell Push |
||||||||
Specification |
|
|
|
|
|
|
|
|
|
|
||||||
Bell Push: DBT-SL |
Plug-ithrough Door Chime: DB306 |
|||||||||||||||
Power: 1 x 23A 12V DC Battery (supplied) |
Power: 240 - 250V 50Hz |
|||||||||||||||
IP44 Weather Resistant |
Range: 75 Metres |
|||||||||||||||
|
|
|
|
|
|
|
Max Load: 1000W |
|
|
|||||||
|
|
|
|
|
|
|
|
|||||||||
|
|
|
|
|
|
|
Indoor Use Only |
|
|
|||||||
Project Manager:Mr G Hunter
R&TTE
APPROVED V1.0
Loading...