™ DB304 Wire Free75MetresChime Kit
1 |
2 |
3 |
Using a small flat |
Insert the 23A battery |
Remove the battery cover and |
|||||||||
screwdriver, insert into the |
(supplied) into the battery |
insert 3 X 1.5V Size ‘AA’/LR6 |
|||||||||
locking clip and gently |
holder, making sure the |
batteries (not supplied), making |
|||||||||
twist. The back plate will |
Positive/Negative terminals |
sure the Positive/Negative |
|||||||||
unclip from the Bell Push. |
match the internal |
terminals match the internal |
|||||||||
|
|
|
markings. Battery Comes |
markings. Chime will ring |
|||||||
|
|
|
Preinstalled |
when batteries are inserted. |
|||||||
4 |
|
|
5 |
|
|
|
|
6 |
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Usage Guide:Avoid positioning the Bell Push/Chime on or directly near metallic surfaces as this may reduce the operation range.
UPVC Door Frames:
When positioning the bell push onto a UPVC door, always check the operating performance before final installation, internal metal frame of the door may affect performance.
Tip: Try adjusting the location of the Bell Push slightly to the Left/Right or place on external wall.
Note: the appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge,unless they have been given supervision or instruction. Children should be supervised to ensure that they do not play with the appliance.
|
Bell Push & Door Chime: |
|
1: Using back plate as template |
|
2: Making sure UP arrow points UP. |
|
3: Mark and drill holes. |
|
4: Insert wall plugs and attach to wall using screws |
|
provided. |
|
5: Clip the Bell Push on to the back plate making sure |
|
Bell Push ‘Clicks’ into place. |
|
6: Place the Door Chime within the operating range (75M). |
|
Transmission of the wire free signal through Walls, Doors |
|
and Ceilings etc, may reduce the operating range. |
|
The Chime is designed for INDOOR use only. |
Melody |
Resetting |
Selection: |
Chime: |
Press the learn button (L) |
Press the Bell Push within |
Test the Chime in the intended |
on the back of the Chime |
30 seconds, the Chime |
location, as internal walls and |
to enter the Learn mode. |
will ring to confirm that |
surfaces may reduce operating |
The chime will ring to |
the Bell Push has been |
range. DO NOT mount onto |
confirm. |
paired to the Chime. |
metallic surfaces. |
Tel: 0845 2301231(UK) |
|
|
|
CH Byron |
|
|
|
Byron House, Sherwood Rd |
|
9-5 Mon-Fri, Local call charges apply |
|
|
|
Astonfields, Bromsgrove |
support@chbyron.com |
|
|
|
B60 3DR |
|
|
|
|
UK |
www.chbyron.com
|
|
|
|
|
To select a new melody for the Door Chime |
To reset the chime and delete the bell push |
|||
1:Press the Melody Select button (M) on the |
learnt to the chime |
|||
back of the Chime unit. |
|
1:Press and hold the Learn button (L) until |
||
2:The Chime will play the newly selected |
the Chime plays a melody - approximately |
|||
melody. |
|
6 seconds. |
||
3:Press again to select the next melody. |
2:The Chime has been reset |
|||
|
|
- see Points 4&5 to pair Bell Push |
||
Specification |
Portable Door Chime: DB304 |
|||
Bell Push: DBT-SL |
||||
Power: 1 x 23A 12V DC Battery (supplied) |
Power: 3 x AA/LR6 1.5V Batteries (Not supplied) |
|||
IP44 Weather Resistant |
Range: 75 Metres |
|||
|
Indoor Use Only |
|
|
|
|
|
Project Manager:Mr G Hunter
R&TTE
APPROVED V1.1