BYD Battery-Box H 7.7, Battery-Box H 9.0, Battery-Box H 10.2, Battery-Box H 11.5, Battery-Box H 6.4 User Quick Reference Manual

BYD Battery-Box HV

QUICK REFERENCE GUIDE

Valid for Battery-Box H 5.1/6.4/7.7/9.0/10.2/11.5 (AU)

V 3

Overall structure

Tools

Skilled personnel recognized This manual and the tasks and procedures described herein are intended for use by skilled workers only. A skilled worker is defined as a trained and qualified electrician or installer who has all of the following skills and expenence:

• Knowledge of the functional principles and operation of on-grid systems.

• Knowledge of the dangers and risks associated with installing and using electrical devices and acceptable mitigation methods.

• Knowledge of the installation of electrical devices.

• Knowledge of and adherence to this manual and all safety precautions and best oractices.

Target Group

Installation environment requirements

Max.

+50℃

Min.

-10℃

Flammable material or gas near the installation

Flammable wall

RH. +5%~+95%

Packing list

Packing of BCU+BASE

①M6 2pcs

⑧ White sealing plug×2pcs

⑦ M6×2pcs⑤ Black sealing plug×3pcs ⑥ White sealing plug ×2pcs

③ Expansion bolt M6 3pcs

* If connected to the SMA inverter, n = 5-8 Modules Unless SMA & BYD updates the information.

Direct sunlight

Direct rain fall

Snow accumulation

YES YES

NO NO

YES

NO

② M4 3pcs ④ OT terminal for Ground×1pcs

Precision screwdriver

Packing of B-Plus H 1.28A

• In order to ensure the normal operation of Battery-Box, please be sure to update the firmware to the latest version and finish the configuration on Battery-Box webpage in accordance with this document.

• The system switch must be off before installing.

• Please make sure the system switch is off in case of the system not working, and it would be better to repair it again within one week, avoiding overdischarge or other problems happen.

• Please do not stack up batteries without protective package when storing or handling batteries, unless in the case of installation.

• Please note that this is the quick reference guide only. It is a shortened assistance for the installation of the Battery HV and

does not replace the original installation manual.The original installation manual must be read and understood completely

before installation. Please download and view the installation manual on this website: www.eft-systems.de (Downloads)

n=7, 9.0KWh

n=8, 10.2KWh

n=9, 11.5KWh

Wire clamp Phillips screwdriver Inclinometer Wrench churn drill

n=5, 6.4KWh

n=6, 7.7KWh

BCU

B-Plus H 1.28A

Base

n=4, 5.1KWh

* Whether the inverter supports 4 battery matching, please consult the inverter manufacturer.

Open the BCU cover Over view of BCULocking

Unpack Balance

I

nstall Wall-mount

Separate base and BCU

Connect the cables

Install the cover

8.

*

9.

6.

7.

4.

5.

2.

3.1.

Internet

P-P

+

BCU + Base

B-Plus H 1.28A

13.

Inverter

P+

WAN

P-

JP2

JP1

Switch BCU PCBA COM1/2 P+/ P-

≥40cm

D=0-6.3cm

D

COM/WAN

P+ / P-/

COM

WAN

P+

P-

Ground

P+

P-

Install sealing plug after install the screws

1. Lock diagonal screws.

2. Lock other

screws.

1. Connecting Ground cable.

2. Connecting negative cable.

3. Connecting positive cable.

4. Connecting communication cable.

5. Connecting network cable.

≥40cm

Avoid the collision between

connector and corners.

Vertical install to protect the connector

Before installing BCU, make sure the system switch is switch off.

10a.

11.

12.

10b.

192.168.5.1.

WLAN

BYDxxx

network 1

network 2

BYDxxx

123456789

cancel login

BYDxxx

Username

installer

cancel login

Password

byd@12345

192.168.6.1.

192.168.6.1

192.168.5.1.

192.168.5.1

BYDxxx

Username

installer

cancel login

Password

byd@12345

Please input file:

Upload

ON

Update

Please input the file :

Upload

If there is any new version on the server, clicking UpdateCheck will update the syesem.

WLAN password

Download the firmware : http://alpspower.com.au/download/

Connect through WIFI

Connect through ethernet cable

Setup system information

Update the firmware

You must update the lastest firmware of BCU after completing the Battery-Box H 5.1-11.4,to prevent battery overdischarge or damage.

network cable

①Connect the network cable ②Set your computer IP into a static IP

IP address:192.168.6.10

Subnet mask:255.255.255.0

Setting method reference computer system setting method

③

④

Battery-Box HV

Privacy Policy

Home

Device Information

Installation Config

Statistics Information

Current Alarm

History Alarm

Run Date

Set Password

Update

1 32

STEP 1 STEP 2 FINISH & REBOOT

1 32

STEP 1 STEP 2 FINISH & REBOOT

Time and Date *

Hour : Min : Day : Month : Year :

Battery-Box HV

Privacy Policy

Home

Device Information

Installation Config

Statistics Information

Current Alarm

History Alarm

Run Date

Set Password

Installtion

Server IP Address *

Series Battery Conts *

Inverter *

Country * Asterisk(*)Indicates required fields

bboxhserver.byd.com.cn 4/5/6/7/8/9

SMA

1 32

STEP 1 STEP 2 FINISH & REBOOT

Last

Search...

Search

These parameters is important. Please make sure the correct configuration for these parameters, otherwise the system might not work normally.

Reboot System… Please wait about 50 seconds.

13a.

2

4

6

8

10

1

3

5

7

9

D E F

A B C

2

4

6

8

10

1

3

5

7

9

13b.

SMA Sunny Boy Storage 2.5 software version ≥ SBS2.5-V2.04.23

SMA Sunny Boy storage 2.5 / 3.7 / 5.0 / 6.0

SMA Sunny Boy Storage

Battery-Box

No. SMA SBS Parameter

1

Battery-Areas of application-Lower Imt deep disch.Protect area prior shutdown

Battery-Nutzungsbereiche-Untere Grenze des Tiefenladenschutzbereichs vor Abschaltung

2%

2

Battery-Areas of application-Minimum width of deep discharge protection area

Battery-Nutzungsbereiche-Minimale Breite des Tiefenladenschutzbereichs

3%

3

Battery-Areas of application-Area width for conservi

n

g battery sate of charge

Battery-Nutzungsbereiche-Breite des Bereichs zur Erhaltung des Batterieladezustands

3%

4

Battery-Areas of application-Minimum width of own consumption area

Battery-Nutzungsbereiche-Minimale Breite des Tiefenladenschutzbereichs

100%

KOSTAL PIKO

BA

pin pin

2

4

6

8

10

1

3

5

7

9

1

3

4

5

7

5

6

2

4

1

3

6

10

9

8

5

7

1 2 3 4 5 6

RS485 - EM-

T

yp 4

KOSTAL

Battery-Box

KOSTAL PIKO BA software version ≥ Firmware:FW-B2.30

UI:UI-B6.44

KOSTAL PIKO BA

Valid for PIKO 6.0 BA，PIKO 8.0 BA，PIKO 10 BA

Choose any one

KOSTAL

PLENTICORE

PLUS

2

4

1

3

6

10

9

8

5

7

B-Box

KPP

1

3

5

7

1

6

5

4

1 2 3 4 5 6

KOSTAL PLENTICORE plus

Set Battery parameters in the SMA inverter:

Use a twisted-pair wire for CAN_H and CAN_L (PIN 6 and 8). This is important for the stability of the CAN communication.

Choose any one

pin pin

2-EN 11V+

4-EN 11V-

6-CAN H

8-CAN L

B-Enable

C-GND and

shielding

E-CAN H

D-CAN L

Battery-Box

SMA SBS

13c.

Fronius Symo Hybrid

2

4

6

8

10

1

3

5

7

9

Choose any one

2

4

1

3

6

10

9

8

5

7

Battery-Box

Fronius

2

4

5

7

+

-

D+

D-

2

4

1

3

6

10

9

8

5

7

2

1

3

6

10

9

8

JP2

Remove JP2

Fronius Smart Meter

Battery-Box

D+ D-

-

D-

-

5

7

4

Please refer to the inverter installation manual for detailed wiring.

D+

JP2 is in the BCU of Battery-Box

Connection method 1

Connection method 2

1.When connecting the meter in the second connection mode, the jumper cap above the JP2 in the BCU PCBA must be unplugged. If not unplugged, it is possible that the Battery-Box and inverter will not be

able to communicate properly.

2.Due to simplicity of installation, connection method 1 is recommended.

BMS

13d.

Goodwe ET Inverter

Goodwe ET

① 1 Cut the BMS cable of the Goodwe ET (according to Goodwe Manual).

③ Download the EzViewer for setting the inverter ④ Setting the inverter

IOS APP Store

ANDROD

2

4

1

3

6

10

9

8

5

7

2

4

1

3

6

10

9

8

5

7

Blue

white-blue

Goodwe

BMS

② Connect the blue PIN to terminal block position 6 and the white-blue PIN to terminal block position 8, according to the picture.

Choose any one

2

4

1

3

6

10

9

8

5

7

Blue

white-blue

Battery-Box

Ingeteam

6

8

CAN IN-H

CAN IN-L

J76

Battery-Box

Ingeteam

Ingeteam Ingecon Sun Storage 3TL and 6TL

13e.

Ethernet cable without the RJ45 terminals

14.

Battery-Box HIGH VOLTAGE EXTENSION

Charge or discharge the original battery module so that its SOC becomes 30% to 40%, and add another battery module. The actual SOC difference will be automatically balanced in the next 2 weeks or so.

(Batterry-Box capacity may not be enough during this

time, this is normal)

15b.

SOC=100%

100% = Green LED

constantly on

HV Charger

15a.

HV Charger

Charging = Green

LED blinking

With charger

15c.

SOC=100%

This manual is a shortened assistance for the installation of the Battery-Box HV and does not replace the original manual, which can be found on http://alpspower.com.au. The installation must be carried out by a qualied expert. Attention, High Voltage Storage! Improper handling can cause

danger and damage.

15d.

n=3-8 Modules

m=1-6 new Modules

Up to a maximum of 9

Battery-Box HV

Privacy Policy

Home

Device Information

Installation Config

Statistics Information

Current Alarm

History Alarm

Run Date

Set Password

Update

Installation

1 32

STEP 1 STEP 2 FINISH & REBOOT

1 32

STEP 1 STEP 2 FINISH & REBOOT

Time and Date *

Hour : Min : Day : Month : Year :

Series Battery Conts *

Inverter *

Country * Asterisk(*)Indicates required fields

bboxhserver.byd.com.cn

SMA

Last

STEP 1 STEP 2 FINISH & REBOOT

Reboot System… Please wait about 50 seconds.

n+m

15c.

SOC=30%-40%

Without charger

New battery module

Original battery system

These parameters is important. Please make sure the correct configuration for these parameters, otherwise the system might not work normally.