IAP2506-M0_032013
Shop Press
Instruction Manual
MODELS: IMP2506, IAP2506, IMPD2506, IEPD2506 CAPACITY: 25 Ton
IMP2514, IAP2514, IEP2514 & IEPS2514
SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153
Tel: 888-332-6419 - Fax: 816-891-6599
E-mail: sales@bvahydraulics.com Website: www.bvahydraulics.com
Max. Operating Pressure 10,000 PSI
Model IMP2506 shown
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
!
! ADVERTENCIA
• Leer, comprender, y seguir las instrucciónes antes de
utilizar el aparato.
• El manual de instrucciónes y la información de seguridad
deben estar comunicado en lengua del operador antes
del uso.
• No seguir estas indicaciónes puede causar daños
personales o materiales.
! WARNING
To avoid crushing and projectile injuries:
•
An ASME B15.1-2000 compliant guard shall be
installed on this device before use.
•
Wear personal protective equipment when operating
this equipment.
Read this manual and follow all the Safety Rules and Operating Instructions before using this product.
Printed in U.S.A
! WARNING
• Study, understand, and follow all instructions before operating the device.
• Do not exceed rated capacity.
• Prior to use, make sure press is securely anchored.
• The press shall be installed and operated in accordance with federal (OSHA), state and local safety
standards.
• Operators and observers shall wear eye protection that meets ANSI Z87.1 and OSHA standards.
• Keep hands, arms, feet and legs out of the work area. Accidental slippage can result in personal injury.
• Use appropriate guarding to contain any pieces that may break or y apart when applying force.
• Use only press accessories having a capacity rating equal to or greater than the capacity of the press.
• Verify lift cables are slack before pressing on the bolster.
• Avoid off-center loads.
• No alterations shall be made to the product.
• Failure to heed and understand these instructions and markings may result in personal injury, property
damage or both.
SAFETY AND GENERAL INFORMATION
Save these instructions. For your safety, read and understand the information contained within. The owner and
operator shall have an understanding of this product and safe operating procedures before attempting to use this
product. Instructions and safety information shall be conveyed in operator’s native language before use of this product
is authorized. Make certain that the operator thoroughly understands the inherent dangers associated with the use
and misuse of the product. If any doubt exists as to the safe and proper use of this product as outlined in this factory
authorized manual, remove from service immediately.
Inspect before each use. Do not use if broken, bent, cracked or otherwise damaged parts are noted. If any
component of this product has been or suspected to have been subjected to a shock load (a load dropped suddenly,
unexpectedly upon it), discontinue use until checked out by qualied personnel such as an Authorized Service Center.
Owners and operators of this equipment shall be aware that the use and subsequent repair of this equipment may
require special training and knowledge. It is recommended that an annual inspection be done by qualied personnel
and that any missing or damaged parts, decals, warning/safety labels or signs be replaced with factory authorized
replacement parts only. Any component of this Equipment that appears to be damaged in any way, is worn or operates
abnormally shall be removed from service immediately until such time as it can be repaired/replaced. Labels and
Instruction Manuals are available from manufacturer.
PRODUCT DESCRIPTION
BVA Shop presses are designed for automotive, truck, implement, eet, and industrial repair shops where pressing,
bending, straightening, forming is required. Each press includes a cylinder and a pump. A winch assembly provides
a safe and efcient way to raise and lower the bed frame, and a pressure gauge which provides for monitoring the
applied press force. Typical applications include installation and removal of alternator and power steering pump
bearings, axle bearings, transmission bearings, seal, driveshaft bearings and u-joints and others. It is not intended
for use as an assembly table or as xture stand used to secure a large, nal assembly component.
WARNING: Wear personal protective gear when operating this equipment.
WARNING: Avoid damaging hydraulic hose. Do not allow hose to kink, twist, curl, crush, cut or bend so tightly
!
that uid ow within the hose is blocked or reduced. Periodically inspect the hose for wear. To reduce the risk
of personal injury and/or property damage, ensure rated working pressure of each pressurized attachment is
equal to or greater than rated working pressure of pump.
2
Electric Pump
(Model IEPD2506,
IEP2514 & IEPS2514)
Pressure Gauge
Pump Bracket
Manual Pump
(Model IMP2506,
IMPD2506, &
IMP2514)
Cylinder
Upper Cross
Member
Winch
Arbor Plates
(Optional, not
included with
the press)
Lower Cross Member
Bed Frame
Air Pump (Model IAP2506
& IAP2514 )
Figure 1 - Typical Shop Press Components
SPECIFICATIONS
Press
Model
IMP2506
IMPD2506 6/HD2506 P2301M
IAP2506 6/H2506 PA1500
IEPD2506 6/HD2506 PEM0501T
IMP2514
IAP2514 PA1500
IEP2514 PEW0501T
IEPS2514 PESL0501T
Rated
Capacity
(tons)
25
Cylinder
Stroke/Model
(in)
6/H2506 P1000
14/H2514
Pump Model
P2001
Support Pin
Upright Channel
Base
Min.
Bed
Width
11-1/2 71 x 48 x 28 4-1/2” 47-1/4”
Press Size
(H” x W” x L”)
Work
Space
(in)
Max.
Work
Space
(in)
Cylinders
Cylinder
Model
H2506
H2514 73.25 18.74 32.99
HD2506 30.53 10.29 16.19 1.77 .98
Rated
Capacity
(ton)
25 5.14
Effective
Area
(in2)
Oil
Volume
(in2)
30.53 10.79 16.73
Min.
Height
(in)
Min.
Height
(in)
Outer
Dia.
(in)
3.35
3
Ram
Dia.
(in)
2.24
Saddle
Dia.
(in)
1.97 3-5/16”-12 UNC
Collar
Thread
Collar
Thread
Length
(in)
1.93
Loading...