Buyers LT32 Installation Instructions Manual

Installation Instructions

LT32 Locking Gas Can Rack

Designed to work with the following gas cans:

• Blitz USA Inc. 5 gal and 6 plus gas cans

• Midwest Can Co. 5 gal cans
Models 5600, 7600, & 8600

• No-Spill Inc. 5 gal cans
Models 1058, 1450, 1456, & 1457

Before you begin installing:

1. Read and understand these instructions

completely.

2. Verify that you have received all the parts

listed in the bill of materials.

www.buyersproducts.com

Phone [phone]

Fax [phone]

CAUTION

Always wear safety glasses when using power tools

Utility Trailer Installation Instructions

Tools and Materials Required:

• 9/16" Wrench or Socket

• 7/32" Hexagon Allen Wrench

• Electric Drill

• 3/8" Drill Bit

1. Place the gas can rack on the rail of your

utility trailer where you would like it mounted.

Make sure the rack does not extend past the
widest part of the trailer. Align the holes in the

bottom of the gas can rack with the center of the
rail.

2. Mark the position of the three holes on the

trailer rail.

Fig. 1

Bill of Materials

ITEM PART NO. QT Y. DESCRIPTION

1 3030321 1 Rack, Locking Gas Can, Only

2 3004396 3 Screw, Button Head, 3/8" x 1-1/4", Zn

3 FWF038100007 3 Washer, Flat, 3/8" UUS, Zn

4 FNE038 01604 4 3 Nut, Nylock, 3/8", Zn

5 3005729 1 Pin, Lock, Gas Can Rack

6 3005730 1 Lock, 1-1/2" Pad w/ Keys

WARNING

Check for locations of brake lines and electrical wiring etc.,
before drilling any holes. Any damage to trailer during instal­lation is the installer’s sole responsibility.

3. Drill 3/8" holes in the positions marked.

4. Bolt the rack to the trailer with three 3/8-16
X 1-1/4 socket head cap screws, six 3/8" flat
washers, and three 3/8-16 nylock nuts supplied
and tighten.

5. Assemble the lock pin to the gas can rack
through the two 1/2" holes in the tabs. Align the
5/16" hole in the lock pin with top hole in the gas
can rack and assemble lock.

—continued inside

Enclosed Trailer Installation
Instructions

Tools and Materials Required:

• 9/16" Wrench or Socket

• Electric Drill

• 1/4" Drill Bit

• 3/4" Plywood Shim Strips

• Shim screws

1. In order to mount this rack to an enclosed

trailer, you must first add 3/4" plywood shim
strips to the walls. These shim strips must be
attached to at least two wall support studs
with suitable fasteners. If you don't know
what kind or length of fastener to use contact
your trailer dealer or manufacturer for their
recommendation.

www.buyersproducts.com

Phone [phone]

Fax [phone]

2. Place the gas can rack against the shims,

hold level, and mark the position of the three
3/8" holes in rack onto the shim boards.

WARNING

Check for locations of brake lines and electrical wiring etc.,
before drilling any holes. Any damage to trailer during instal­lation is the installer’s sole responsibility.

3. Drill three 1/4" pilot holes in the positions just

marked for the 3/8" lag screws. Be extremely

careful not to drill through the outside trailer
wall.

4. Fasten the rack to the trailer wall with the

three 3/8" X 1-1/4" lag screws and three 3/8" flat
washers supplied.

5. Assemble the lock pin to the gas can rack

through the two 1/2" holes in the tabs. Align the
5/16" hole in the lock pin with top hole in the gas
can rack and assemble lock.

Fig. 2

Bill of Materials

ITEM PART NO . QT Y. DESCRIPTION

1 3030321 1 Rack, Locking Gas Can, Only

2 FWF038100007 3 Washer, Flat, 3/8" UUS, Zn

3 3004486 3 Screw, Hex Head Lag, 3/8 x 1-1/4, Zn

4 30 05729 1 Pin, Lock, Gas Can Rack

5 3005730 1 Lock, 1-1/2" Pad w/ Keys

WARRANTY

Buyers Products Co. warrants all truck /trailer hardware man­ufactured or distributed by it, to be free from defects in material
and workmanship for a period of one year from date of shipment.
Parts must be properly installed and used under normal conditions.
Any product which has been altered, including modification, mis­use, accident or lack of maintenance will not be considered under
warranty. Normal wear is excluded. The sole responsibility of Buyers
Products Co. under this warranty is limited to repairing or replacing any
part or parts which are returned, prepaid, and are found to be defective
by Buyers Products Co. Authorization from Buyers Products Co. must be
obtained before returning any part. No charges for transportation or labor
performed on Buyers’ products will be allowed under this warranty.

3030371_A