Easifold Rollaway 19
Table Tennis Table
Assembly Instructions
R
R
R
i
R
la
y
Eas fold
ol
wa
Easi
ld Rolla
ay
fo
w
PARTS LIST
1. TABLE TOP PARTICLE BOARD- 1525×1370×18MM - 2 NOS.
2. END FRAME PIPE -1490×30×20MM - 2 NOS.
3. SIDE FRAME PIPE - 1310×30×20MM - 4 NOS.
4. INNER FRAME PIPE - 930×30×20MM - 2 NOS.
5. SPANNER - 7.5/6MM - 2 NOS.
6. OUTER LEG - 940×710×45×25MM - 2 NOS.
7. INNER LEG -1080×500×45×25MM - 2 NOS.
8. LONG BRACE SUPPORT - 665×25×7MM - 4 NOS.
9. WHEEL ASSEMBLY- 500×230×45×25MM - 4NOS.
10. SET OF 8 WHEELS - 75 MM WITH 2 LOCK WHEELS
11. BRACKETS FOR OUTER/INNER LEG - 75×28MM - 16 NOS.
2
12. BRACKETS FOR FRAME PIPE - 38MM - 20 NOS.
13. BRACKETS FOR SIDE LOCK - 75×19MM - 4NOS.
14. BOLTS FOR OUTER/INNER LEG 62×7.5MM - 8 NOS.
15. BOLTS FOR LONG BRACE SUPPORT FIXED TO OUTER/INNER LEG
- 75×7.5 - 6 NOS.
16. BOLTS FOR SIDE LOCK ATTACHED TO OUTER LEG - 88×6MM
WITH NUT WASHER AND BHOGLI - 2NOS.
P23
17. BOLTS FOR SIDE LOCK ATTACHED TO BRACKET - 31×6MM - 2 NOS.
18. DOME NUT - 10MM- 8 NOS.
19. OUTER CORNER - 43MM - 4 NOS.
20. SET OF POST CORNER - 50×18MM - 2 NOS.
21. LEVELLERS - 45×25MM CAPSULE - 4 NOS.
22. CENTRE LOCK - 2 NOS.
23. SIDE LOCK - 2 NOS.
24. PLASTIC CAP FOR SIDE FRAME PIPE - 20×30MM - 4 NOS.
25. PLASTIC CAPS FOR INNER FRAME PIPE - 23×17MM - 8 NOS.
26. WHEEL ASSEMBLY CAP - 45×25MM - 8 NOS.
27. NET POST SET - 1 NOS.
28. BOLTS TO ATTACHED WHEEL ASSEMBLY( P9) WITH INNER LEG (P7)
62×7.5MM - 8 NOS.
29. SPARE NET - 1 NOS. (×)
30. SCREW FOR BRACKETS ON TOP 8/32- 48 NOS. 8/13- 216NOS.
31. SCREW FOR OUTER CORNER & POST CORNERS - 6/13- 20 NOS.
P4
P24
P17
P13
P16
P25
P18
P14
P11
P20
P15
P12
P22
P28
R
fol
lawEasi d Rol
ay
fo
lEasi
ld Rol away
P19
P9
P7
P21
P10
P8
P3
P6
P26
P1
P2
P27
ADULT ASSEMBLY REQUIRED
P-28 - 62×7.5MM - QTY. - 8
P-5 - 7.5/6 MM - QTY. - 2 P-9 - 500×230×45×25 MM - QTY. - 4
PLEASE READ THE SAFETY INSTRUCTIONS AT THE BOTTOM OF PAGE- 4
STEP - 1
CAREFULLY LIFT THE TABLE TOP HALF TO ATTACH
WHEEL ASSEMBLY (P9) WITH INNER LEG (P7) USING
NUT & BOLT 62×7.5 AND TIGHTEN IT WITH THE HELP
OF TWO SPANNERS.
STEP- 2
PUSH
SLIGHTLY PULL OUT THE
OUTER LEGS (P6) & PUSH OPEN
THE TABLE SLIGHTLY BY
OPENING CENTRE LOCK (P22).
P-28 - 7.5MM - QTY. - 8
STEP- 3
NOW SLIGHTLY PULL OUT THE
SIDE LOCK (P23) & SLOWLY
BRING DOWN THE TABLE
PULL
STEP- 4
REPEAT THE SAME FOR THE 2ND HALF OF THE TABLE AS IN STEP- 1, 2, & 3
STORING THE TABLE
PULL
STEP- 1
PULL OUT THE SIDE LOCK (P23) TO LIFT THE TABLE ON THE WHEELS.
MAKE SURE THAT LOCK (P22) IS LOCKED PROPERLY FOR STORAGE
REPEAT THE SAME FOR THE 2ND HALF.
STEP- 2
STEP- 5 STEP- 6
YOUR TABLE IS NOW READY FOR PLAY
Safety Instructions: Children below 14 years should not assemble the table. When lowering each half of the table top, make sure
that the outer legs P6 are pulled gently outwards from the underside of the table, so far as they can go. Failure to do this may result
in injury or damage to the table. This table is suitable for indoor use. It can be used outdoors provided that it is not exposed to direct
sunlight rain or frost. It should always be stored indoors. Make sure that the wheel brakes are off when moving the table and are on
when the table is stored or in the play position.
STEP- 7
ADJUST THE HEIGHT REQUIRED WITH THE HELP OF LEVELLERS (P21)
ATTACHED ON ALL 4 OUTER LEGS (P6).
Loading...