MODEL: BIG EYE G3MODEL: BIG EYE G3
SMS remote control SMS notification s
Sen ding interval
USER GUIDEUSER GUIDE
VER.
201707
Contents
I. Introduction ........................................................................... 1
1.1 Application ......................................................................... 1
1.2 Power source ...................................................................... 2
1.3 Memory card ...................................................................... 3
1.4 USB functions .................................................................... 4
1.5 Precautions ......................................................................... 5
II. Camera structure knowledge ................................................. 7
2.1 Front structure of the camera ....................................... 7
2.2 Internal structure of the camera ................................. 8
III. Use camera quickly ................................................................ 8
3.1 Start camera quickly ........................................................... 9
3.2 Start 3G mode quickly........................................................ 9
IV. Menu function table ............................................................ 12
V. Network functions ............................................................... 19
5.1 Remote control operation procedure by SMS ................... 19
5.2 PC client setting ............................................................... 23
5.2.1 Camera parameters setting..................................... 24
5.2.2 Network parameter setting ......................... 25
VI. Main performance and technical parameters of the product
30
6.1 Main functions ..................................................... 30
6.2 Technical parameter ......................................................... 32
VII. Other ................................................................................... 36
7.1 "REPLAY" key ................................................................ 36
7.2 Detailed explanations for partial functions ....................... 38
7.2.1 Timer settings ........................................................ 38
7.2.2 Language ............................................................... 38
7.3 Firmware Upgrades .......................................................... 38
7.4 Frequently Asked Questions ............................................. 39
7.4.1 Camera cannot start normally ................................ 39
7.4.2 If the camera cannot get the remote picture and
information ..................................................................... 40
7.5 Factory default settings .................................................... 40
VIII. Warranty Policy .................................................................... 41
Appendix I: Corresponding table of length of the video and interval
time of taking photos ..................................................................... 43
Appendix II: Standard Packing List.................................................. 44
IX. Statement ............................................................................ 44
1
V. Introduction
Big Eye G3 wildlife camera (also known as wireless hunting camera
/ 3G trail cameras) is an wireless infrared detection device with 3G
network. It is triggered by pyroelectric infrared sensor (PIR). Any
change of environment temperature caused by movement of animals
in observation area automatically triggers completion of photographs
or video. The detection photos could be sent by the camera to a
mobile phone or mailbox via 3G network and remote setting of
camera can be achieved by SMS.
1.1 Application
A． The product can be used by hunting enthusiasts to detect
animal and animal infested areas.
B． Ecological photography enthusiasts, wildlife protection
volunteers, etc. can use it for outdoor automatic image
shooting.
C． It can be used for growth observation of wildlife and
plants.
D． It is also installed indoor or outdoor, monitoring home,
supermarket, construction site, warehouse, community
and other places.
E． Forestry units, forest police can use the product to detect
2
stealing and illegal hunting, as well as for evidence
obtaining.
F． It can be used in other aspects for evidence collection.
Notes to users:
Please read the instructions
carefully before using this product, so as
to avoid unnecessary loss!
Do not disassemble the camera
arbitrarily. Except for product quality
problems, the manufacturer does not
take any responsibility for damage
caused by users!
1.2 Power source
AA battery or external power adapter shall be used for power supply
to this product.
A. Battery-powered: Please use high quality alkaline battery, Ni MH
battery or rechargeable battery. It supports two sets of battery
installed to this camera, 4 batteries in each set. 8 batteries are
advised to install, so as to improve the performance of the camera.
Note: The users need to purchase battery themselves. Please
3
pay attention to the positive and negative electrode of the battery in
installation. When you do not use the camera for a long time, please
take out the battery, to avoid any damage to camera caused by
liquid leakage. When battery capacity is low, please replace themin
time.
B. External power supply:
This product supports 6V/2A DC power adapter, solar power, etc.
Note: When battery capacity is low, under the "TEST" mode,
there will be a low power prompt shown on the screen (the battery
icon at lower right corner will be displayed as empty and red "X");
under the "ON" mode, the red indicator light flashes for continuous
60 seconds with interval.
1.3 Memory card
SD card is used in this camera for image storage, the maximum
capacity of 64GB. In order to ensure that the camera can achieve the
best performance, please use the SD card of 10 Speed or above;
when the camera is turned on, please do not remove the SD memory
card, battery and power supply plug!
Note: Before inserting the SD memory card, it is recommended
to format the SD card, to turn off the SD card lock protection, and to
insert the SD memory card correctly according to the logo.
The following table lists of the maximum photo numbers and the
length of the video by different capacity SD cards (the value is for
reference only). You can choose to buy the appropriate SD card of
different capacity based on your requirement.
4
Image amount stored in SD cards with different capacity.
2GB 4GB 8GB 16GB 32GB 64GB
Photo number (piece)
3MP 1644 3320 6746 13234 28055 53752
5MP 1026 2072 4212 8262 17514 33557
8MP 647 1307 2656 5210 11054 21162
12MP 424 856 1740 3414 7238 13868
16MP 320 646 1314 2578 5465 10471
Video length(hour)
1080P 00:16:16 00:32:56 01:07:00 02:11:33 04:38:55 08:14:01
720P 00:34:35 01:09:53 02:22:05 04:38:53 09:51:12 16:05:20
WVGA 00:44:34 01:30:04 03:03:06 05:59:20 12:41:44 19:52:56
VGA 00:52:06 01:45:15 03:33:58 06:59:54 14:50:05 22:32:22
10-second video quantity (segment)
1080P 97 197 402 789 1673 2964
720P 207 419 852 1673 3547 5792
WVGA 267 540 1098 2156 4570 7157
VGA 313 631 1283 2519 5340 8114
1.4 USB functions
This product can be connected to computer or TV with USB
5
interface.
The camera is connected with the USB interface of the computer
through the USB data line, the camera display screen displays the
USB connection symbol, and the operation key is invalid.
Find the removable disk in "my computer", which could be used to
read and write SD card in the camera through the computer.
Note: When the camera is in the OFF mode of shutdown and
without other power supply, USB connection is still operational.
When the camera is successfully connected to the RCA via the TV
cable, and switched to the "TEST" mode for test preview, and
"REPLAY" is selected, the image files in the camera can be browsed
in TV. Note: When the TV is connected, the camera display
screen will be automatically turned off!
1.5 Precautions
A． Under the "TEST" mode, the camera will automatically
shut down when there is no any key operation. If you want
to continue to use, please turn on the switch function key
again to the "TEST" mode. Users can set timing for
automatic shutdown of camera.
B． When the software is upgrading, please ensure there is no
power cutoff. After the completion of upgrade, there shall
be at least 5 seconds maintained after the shutdown or
6
power off, otherwise it may lead to the failure of upgrade. If
the upgrade failed, it may continue to upgrade again.
C． When installing the camera, please ensure there is no
moving object 3 meters range in front of camera, such as
tree branches, leaves, weeds, ropes, ribbon and other
objects fluttering in the wind, so as not to cause the camera
to continuously take pictures by mistake.
D． Please do not keep the camera close to the heat source of
large boiler, air conditioning exhaust, lighting, etc., so as
not to cause the camera to take pictures by mistake.
E． Please do not use any voltage or current value which does
not meet or exceed the requirements forthe external power
supply, to avoid damage to the camera.
F． There is a battery to maintain the clock in the camera, for
time and date setting which will keep working until dead
battery. The date and time settings resume factory settings
after power failure. And after powering on at each time, it is
needed to reset the time and date.
G． Under the test mode, when the network is searched, the
display screen will be turned off, at the same time, the red
and blue working indicator lights flash. When the search is
completed, the display screen of the camera will be turned
7
on again, showing the network signal strength in the lower
left corner of the screen.
VI. Camera structure knowledge
2.1 Front structure of the camera
Microphone
Camera lens
PIR infrared
sensing window
3G
antenna
Infrared
LED light
Photoresistance
Working
indicator
light
8
2.2 Internal structure of the camera
Keyboard
Battery compartment cover plate
Battery compartment
SD card slot
On-off key
SIM card slot
Display screen
USB port
DC power supply port
VII. Use camera quickly
Power switch:
1. When turning to ON, the camera enters into the work mode
(before entering into the work mode, the red work indicator light
flashes for 6 times, the blue light for the 3 times)
2. When turning to TEST, the camera enters into the test mode,
and you can manually set all the parameters, or take photos or videos,
or display photos and videos stored in memory card.
3. When turning to OFF, the camera stops operation.
9
3.1 Start camera quickly
准备 安装电池 安装SD卡 安装SIM卡 开始监测
相机、电池
SD卡、
SIM卡
2组8个电池
注意正负极
ON
设置参数
TEST
3.2 Start 3G mode quickly
1. Check network signal
准备
“MENU”
“▼”
“OK”
“▼”
“OK”
无信号
进入TEST状态
按两次“MENU”键，进入“设置”状态
按“▼”键，找到“网络设置”状态。
按“OK”键
OK？
有信号，显示网络内容
NO
YES
按“▼”键，选择“OK”选项。
按“OK”键
选择“OK”，进入网络搜索状态，液晶屏暂时关闭，红蓝
指示灯同时闪烁。
Preparation
No signal
Battery
installation
SD card
installation
Parameter
setting
Monitoring
starting
SIM card
installation
2 sets of 8 batteries. Pay
attention to the positive
and negative electrode
Camera, battery
SD card, SIM card
Preparation
Enter TEST state
Press "MENU" key twice to enter the "setting" state
Press ▼ key, to find "network setting" state.
Press "OK" key
There is a signal that displays the contents of the network
Press ▼ key, to select "OK" option.
Press "OK" key
Select "OK" to enter the state of the network search and temporarily close the
LCD screen, and the red and blue indicator lights flash at the same time.
10
Network search Confirm to start network search
N
o
S
IM
c
ard
N
O
s
g
n
a
l
s
i
g
n
a
l
s
t
r
e
n
g
t
h
SI
M
c
a
r
d
SIM card intact, good signal No SIM card found, no signal
If the signal is not normal, please send the Debug file.txt file in SD
card back to the manufacturer for troubleshooting.
2. Network standard strength
Network standard is displayed in the camera as: (transmission speed
from low to high)
G GSM
U UTRAN
E GSM W/EGPRS
D UTRAN W/HSDPA
W UTRAN W/HSDPA
H UTRAN W/HSDPA and HSUPA
11
N
e
t
w
ork
s
t
a
nda
rd
3. Check the network setting parameters
准备
“MENU”
“▼”
“OK”
进入TEST状态
按两次“MENU”键，进入“设置”状态
按“▼”键，找到“网络信息查看”状态
显示网络设置的参数
Network information
display
Network information
view
When it is completed, the power switch is turned to the "ON", and
the lock is buckled, the camera is in 3G mode.
4. Check communication module IMEI
Preparation
Press ▼ key, to find "network information view" state.
Enter TEST state
Press "MENU" key twice to enter the "setting" state
Display network facilities parameters
12
Communication module IMEI code can be queried on the menu. At
the first time for using, it is only displayed after searching network.
VIII. Menu function table
Press "MENU" key to enter into cyclic menu. Press ▲or ▼ key to
move the cursor to select a variety of function options. Press
◄and► keys to switch parameters. Press "OK" key for
confirmation. Press "REPLAY" key to enter playback mode. Press
"EXIT" key to return to previous menu or exit the menu.
Bold text in the table is the default value.
When the power switch is turned to "TEST", you can select the
network research in the menu, which can confirm the current
strength of the network signal. When there is no signal or failure of
network search, it is proposed to change the camera position, plug
SIM card again, and check whether the SIM card has arrears.
Parameter
Setting option
(Bold = factory default)
Function description
Image
Mode
Camera /
Video /
Camera + Video
"Camera + Video" is to take
continuous photos according to
the preset number of photo
13
shooting, followed with video
shooting at the preset length on
the same target.
Image Size
3MP/5MP/8MP/
12MP/16MP
High resolution can improve
the definition of the photo, but
it will take up more storage
space, more time for file
storing.
Video Size
VGA/WVGA/
720P/1080P
High resolution can improve
the definition of the video, but
it will take up more storage
space, with the longer file
storage time.
Shooting
No.
1/2/3/4/5/6
For each shooting, picture
number of continuous capture
is based on values set by users.
Note: When the photo
resolution is 16MP, only 3
consecutive pictures can be
taken at the maximum.
Video
5 seconds /10 seconds /15
The video in MOV format can
14
Length seconds /20 seconds /30
seconds /45 seconds /1
minute /2 minutes /3
minutes /5 minutes /10
minutes
be played in the most video
players.
Set
Device No.
BUSH
4 characters; each character
can be selected optionally from
0-9, A-Z. The equipment
number becomes the first 4
characters of image file name.
When viewing pictures, it can
help users identify the camera
used to shoot pictures.
Timer
Off/On
It is used to set the working
time of the camera. Beyond the
time set, the camera will not
work. See 7.2.1 for details
PIR
Interval
Off/ 3 seconds /5 seconds
/10 seconds /15 seconds
/30 seconds /1 minute /2
When the shooting is
triggered, the camera will no
longer be triggered during the
15
minutes /5 minutes /10
minutes / 20 minutes /30
minutes /1 hour
PIR interval. After this period,
the PIR will resume the
waiting state to be triggered.
Time
Lapse
Off/5 seconds /10 seconds
/15 seconds/ 30 seconds
/1 minute /2 minutes /5
minutes /10 minutes/ 20
minutes /30 minutes /1
hour /2 hours /6 hours /12
hours /18 hours /24 hours
The camera could be set for
timing shooting during set
time interval.
Note: Once this function is
turned on, the camera will not
start infrared automatic
sensing for shooting.
* Refer to Appendix I
Stamps
Off/On
If it is turned on, there will be
a LOGO, temperature, moon
phase, date, time displayed
below on each picture.
Power
Saving
Off/On
If it is turned on, there will be
only 20 fill-in lights working
in the camera, with low PIR
level.
Auto
Power Off
1 minute /3 minutes /5
minutes /10 minutes
Auto power off at fixed time if
no keypad controlling.
16
Record
Sound
Off/On
If it is turned on, there is sound
record with video.
PIR Level
Low / Normal / High
The user can set the PIR
sensitivity based on needs.
Sending
Interval
Off/ instant /5 seconds
/10 seconds /15 seconds
/30 seconds /1 minute /2
minutes /5 minutes /10
minutes / 20 minutes /30
minutes /1 hour
Once a photo is shot, if the
camera does not take another
photo within the set time
interval, the camera will send
the photo (by Email or MMS)
or message (under the SMS
mode) according to the set
time interval; When it is turned
off, pictures will not be sent
out.
Note: In the case of low
voltage, the camera cannot
start the 3G module; this will
cause failure in picture
sending. When the time lapse
is selected, the immediate
sending can be set by default
17
automatically. The "OFF" is
selected; network function will
be turned off too.
Net Info Net configuration
Press “OK” key to display
information of current network
mode, receiving phone
number, operator, server
mailbox, server port, sending
mailbox, sending mailbox
password, receiving and CC
e-mail address, etc.
Network Search
After pressing "OK" key, the
screen will show the menu.
Select "OK" option, the screen
display will be turned off and
the mobile will search the
network signal at the location
of the camera. After searching,
the screen will be turned on
again and signal strength is
displayed at lower left screen
18
IEMI
Display the IEMI code for the
current network module
System
Formatting
SD card
Format SD card
Set Clock
2017/01/01 00:00
Set system time of the camera.
Default Set
Factory
Restore all settings to factory
defaults.
Language
English
Support multiple languages:
See 7.2.2 language
Beep
Sound
Off/On
Turn on or off the key sound.
Loop
Recording
Off/On
When the SD card is full, it
will automatically overwrite
the previous file.
TV Mode
PAL/NTSC
When the camera is connected
to the TV, set the local TV
broadcast system.
Password
Set
1234
4 characters, arbitrarily
selected in 0-9. Please contact
your dealer in the case of
password loss.
19
Software
Ver.
G3___01_6.1.01
G3: Camera model;
01: Language Section;
6.1: Software version number;
01: Customized software
version number.
Playback
Delete
Delete current / delete all
Delete single one or all images
Protect
Lock current / unlock
current / lock all / unlock
all
Locked image cannot be
deleted. Only after unlocking,
it could be removed. Used to
protect important images, and
avoid accidental deletion.
Slide
Show
3 seconds /5 seconds /8
seconds
Interval for auto play of
images. The camera will
display the slide time as set
interval.
IX. Network functions
5.1 Remote control operation procedure by SMS
All parameter setting begins with "#" for separation, "=" followed
with parameters, "*" at the end.
S/N SMS instruction SMS sample
20
1
Pattern: Photo (1), video (2), photo +
video (3)
#01=1*
2
Image Size:
3MP(1),5MP(2),8MP(3),12MP(4),16MP
(5)
#02=1*
3
Video size
720P(1),1080P(2), VGA(3), WVGA(4)
#03=1*
4
The number of continuous shooting: 1
unit (1), 2 units (2), 3units (3), 4 units
(4), 5 units (5), 6 units (2)
#04=1*
5
Video length: 5 seconds (1), 10 seconds
(2), 15 seconds (3), 20 seconds (4), 30
seconds (5), 45 seconds (6), 1minute (7),
2 minutes (8), 3 minutes (9), 5 minutes
(10), 10 minutes (11)
#05=1*
6
Name of equipment Letters (26 pcs),
numbers (10 pcs)
#06=aaaa*
7
Timing 1: Close-->#07: -: *
#07=12:00-12
:30*
8
Timing 2: Close-->#08: -: *
#08=01:30-01
:40*
21
9
PIR dormancy: 3 seconds (1), 5 seconds
(2), 10 seconds (3), 15 seconds (4), 30
seconds (5), 1 minutes (6), 2 minutes
(7), 5 minutes (8), 10 minutes (9), 20
minutes (10), 30 minutes (11), 1 hour
(12), off (13)
#09=1*
10
Interval shooting: 3 seconds (1), 5
seconds (2), 10 seconds (3), 15 seconds
(4), 30 seconds (5), 1 minute (6), 2
minutes (7), 5 minutes (8), 10minutes
(9), 20 minutes (10), 30 minutes (11), 1
hour (12), 2 hours (13), 6 hours (14), 12
hours (15), 18 hours (16), 24 hours (17),
turn off (18)
#10=1*
11 Figure stamp: On (1), Off (2) #11=1*
12 Power saving mode: On (1), Off (2) #12=1*
13
Automatic shutting-down: 1 minute (1),
3 minutes(2), 5minutes (3), 10minutes
(4)
#13=1*
14 Voice Recording: On (1), Off (2) #14=1*
15 PIR-level: Low (1), normal (2), high (3) #15=1*
22
18 Key sound: On (1), Off (2) #18=1*
19 Loop record On (1), Off (2) #19=1*
20 TV Output: PAL (1), NTSC (2) #20=1*
21
Password setting: Letters (26 pcs),
numbers (10 pcs)
#21=1234*
22
Network mode: Turn off (0), SMS (1),
email (2), MMS (3)
#22=0*
23
Receiving phone number:
#23=1234567
8901*
32
Receiving mailbox:
#32=xxx@g
mail.com*
33
CC mailbox:
#33=xxxx@g
mail.com*
35
Image format: 1 (original), 2
(thumbnail)
#35=1*
36 SMS mode: 1 On, 2 Off #36=1*
38
Transmission interval: Immediately (1),
5 seconds (2), 10 seconds (3), 15
seconds (4), 30 seconds (5), 1 minutes
(6), 2 minutes (7), 5 minutes (8), 10
minutes (9), 20 minutes (10), 30 minutes
#38=1*
23
(11), 1 hour (12), off (13)
After the camera is set with remote SMS, when the camera
restarts next time, a message will be sent to the mobile phone.
Safety SMS function: In the induction mode, following a
normal shooting and sending if there is no other shooting in the
next 12 hours, then the camera will send a message to inform
the current state of the camera (including: time, energy,
remaining storage capacity) to receiving mobile phone number.
5.2 PC client setting
PC client application can be downloaded from the website of our
dealers, without need for installation. Just download and decompress
the G3set.exe program to run. The SIM card in the camera must
support WCDMA 3G pattern.
Please select the appropriate language, camera model for the first
interface.
24
5.2.1 Camera parameters setting
Click the camera settings for the camera parameter settings.
After parameter setting, click on the "directory" to select the file
storage address. Click "generate" to generate the camera parameter
settings file as “CameraSet.cfg” filename. Click "Exit" to exit the
25
main menu interface.
Copy the parameter settings file of CameraSet.cfg to the SD card.
Insert it to the camera and turn the key to TEST, camera setting is
automatically finished.
Load: If the generated parameters are incorrect, click "Load" to
select the generated file, you can quickly restore the generated
parameters, convenient for modify the parameters again.
Default: Restores default settings.
5.2.2 Network parameter setting
Click the network settings for the network parameter settings.
Select the "automatic" mode to set. After selecting the country, the
operator, the software will use the network parameters provided by
the system, by entering mailbox, telephone number and other
26
parameters. Then you can use it. If the parameters provided by the
system are incorrect or no option, the user can choose the "manual"
mode, to fill in all the network parameters, e-mail, telephone number.
For network APN, server used, port, APN account and APN
password, please consult local communications operators.
After parameter setting, click on the "directory" to select the file
storage address. Click the "generate" to output camera settings file to
the directory of the file storage address. Click "Exit" to exit the main
menu interface.
Copy the parameter settings file of Camera NetSet.cfg to the SD
card. Insert it to the camera and turn the key to TEST, and then the
camera automatically sets the parameters.
Load: If the generated parameters are incorrect, click "Load" to
select the generated file, you can quickly restore the generated
parameters, convenient for modify the parameters again.
Default: Restores default settings.
Dave Default: Save the current settings as defaults, no need to set
the parameters next time. If there are any changes, click "Default" to
restore the saved settings.
Email mode parameter settings
In the network settings menu, select the “EMAIL” option for email
mode parameter settings.
27
After selection of the filling way, country, operators, it is
needed to fill in the NET APN(Access Point Names), Send Server,
Port, Send Name (Mailbox), Send Mailbox Password, Receiving
mail, CC mail, Send Interval. For sending SMS, you need to fill in
phone number. In some countries, it is required to fill in the APN
Account, APN Password. If the operator does not require, that two
parts can be empty.
By this mode, the photos will be sent to the receiving mailbox
by sending mailbox. The default is to send a thumbnail without
message notice. If the original images and SMS notification are
needed, you can choose to change.
MMS mode parameter settings
In the network settings menu, select the “MMS” option for MMS
28
mode parameter settings.
After selecting the Country, Operator, it is needed to fill in the
Send Interval, Phone Number, MMS APN, MMS URL, MMS
Proxy Server, MMS port. In some countries, it is required to fill
out the APN Account, APN Password. If there are no requirements
for operators, the two parts can be empty. Please consult local
operators for parameters.
Note: In MMS, only thumbnails are sent. SMS is not optional.
SMS mode parameter settings
In the network settings menu, select the SMS option for SMS mode
parameter settings.
29
In this mode, it is required to set the Country, Operator, Send
Interval, Phone Number. When sending SMS, the set mobile
phone number can receive the text information of the image shot by
the camera.
Note: Phone number format is "+8613800138000" or
"13800138000".
After the completion of parameter settings of Email mode, MMS
mode, SMS mode, select the "directory" to fill the storage location
for generating files, and then click "Generate". Copy the generated
NetSet.cfg to the SD card. Insert it to the camera and turn the key to
TEST, and camera setting is automatically finished.
30
X. Main performance and technical parameters of
the product
6.1 Main functions
1) Picture pixels: 3MP/5MP/8MP/12MP/16MP.
2) HD video: 1080P 30 frames per second. The sound of the video
can be set on or off.
3) In the "camera + video" mode, the camera after being triggered to
start every time, the camera will take pictures first and then record a
scene video.
4) 42 infrared LEDs, in power-saving mode, only 20 infrared LEDs
work; 850nm/940nm two kinds of lights are optional.
5) Starting speed at 0.5 seconds
6) 2.4' TFT color LCD screen.
7) Important pictures can be locked to avoid deletion.
8) Continuous shooting for 6 pictures.
9) You can set a specified period every day for the camera to work.
And you can set two timers.
10) PIR interval function, can avoid the multi shot for the same
object that stays for a long time.
11) By time lapse function, the camera will be set at a time interval
to take pictures, which is very useful to observe the flowering of
plants, birds nest, as well as monitoring unattended places, such as
31
parking, garden.
12) Auto power off in 1-10 minutes whiles no keypad controlling.
13) Date, time, temperature, moon phase and battery capacity can be
stamped in the picture.
14)7 operation buttons. The beep sound can turned on or off.
15) Free choice of TV out at PAL/NTSC.
16) Maximum 64GB SD memory card is supported.
17) Low standby power consumption, up to 6 months of standby
time.
18) When power alarms for low battery, there is a low power logo on
the screen with a red light flickering.
19) 1~8 zoom playback for viewing.
20) Supportive for nine square pictures browsing and auto play
mode.
21) Device number will be showed on image file name, this helps
users identify which cameras captured the image when browse files.
22) Yo u can set a password for power-on.
23) Color pictures at daytime, monochrome pictures at night,
switched automatically.
24) Supportive for loop recording, which automatically deletes the
earliest photos or videos and makes room for new ones.
25) Dentate design on the back is more convenient for camera
32
mounting.
27) The battery hatchway cover can effectively avoid corrosion
damage to camera caused by leakage of battery.
28) Image transmission speed is high, transmit image via SMTP/
MMS, network support GPRS / 3G.
29) With SMS notice and remote control functions.
30) Supports thumbnail or original transmission.
31) Can flexibly set images transmission time, can select the instant
sending or interval sending.
32) Set parameter on computer, which is more convenient.
33) If no trigger for 12 hours, it will send safe messages (time,
electric quantity, storage capacity).
6.2 Technical parameter
Items Parameter
Work Mode Camera / Video / Camera+Video
Photo Size
3MP:2048×2536 ; 5MP:2542×1944
8MP:3264×2488 ; 12MP:4032×3024
16MP:4640×3480
Video Size
VGA:640x480; WVGA:800x480
720P:1280x720@30fps; 1080P:1920x1080@30fps
Working Time Day /night, auto-induction switch
33
Lens
FOV=90 degree (G3R:50 degree), F=2.4 (G3R:2.5),
auto-induction switch filtering
IR Flash Distance 65 feet / 20 m
Infrared Lamp
42pcs; Visible light lamp/invisible light lamp
selectable
Power Saving On/off; Only 20 lights work after opened
LCD screen 2.4 inch, TFT colors, RGB
Operation Keypad 7 buttons
Beep Sounds On/off
Memory SD card, maximum support 64GB
PIR Level High/Normal/Low
PIR Sensing Distance 65 feet / 20 m
PIR Sensing Angle 90 degree (G3R:50 degree)
Trigger Time 0.5 seconds (when use 2 GB card)
PIR Interval
3 seconds ～60 minutes, Programmable
Timer On/ Off, can set two timers
Time Lapse 5 seconds ~ 24 Hours, Programmable
Shooting Number
1～6 photos (1～3 photos when in 16MP)
Video length
5 seconds～10 minutes, Programmable
Camera + Video Take photos first, and then record video
Playback Zoom 1~8 times
34
Slide Show 3 Second/5 Second/8 Second
Loop Recording On/Off
Lock Image
Locked or unlock image
Stamps
On/Off, Logo, temperature, moon phase, date, time,
battery power
Password 4-digit number, each digit can be freely set with 0 ~9
Device No.
4-digit number, each digit can be freely set with 26
alphabets or 0~9.
Network Band 800/850/900/1900/2100MHz
Email
Two mailboxes can be set.
Message notice can be set at the same time.
Either original (maximum 16M) or thumbnail
(640x480) can be sent.
MMS Only send thumbnail (640x480)
SMS Send message notice
Sending Interval Instant, 5sec~1 hour, Off
Safety Message
No trigger for 12 hours, it will send message (time,
electricity quantity, remaining storage capacity) to
designated cell phone.
Standby Time 3~6 months (4×AA~8×AA)
Auto Power Off Automatic shutdown can be set for 1~10 minutes with
35
no operation.
Power Source 4×AA, 8×AA
External DC Power
Supply
6V/2A
Standby Current 0.4mA
Power Consumption
200mA( +700mA when IR LED lights up)
250mA (start network, maximum peak is 400mA)
Low Battery Alarm 4.8V
Interface
TV-out/USB, SD card slot, 6V DC power port,
network antenna, SIM card slot
Mounting Strap; Tripod nail
Waterproof IP66
Network Module
operating temperature
-40～＋85°C
Working temperature
-22～＋158°F/-30～＋70°C
Working Humidity
5%～95%
Camera Dimensions 147.5×100×77 (mm)
Net Weight 350g
Certified
FCC＆CE＆RoHS
36
XI. Other
7.1 "REPLAY" key
"REPLAY" key, with other keys can achieve
browsing/playing/deleting of images which have been stored in SD
card; Photos can be enlarged /shrunk/moved; Video Sudoku
thumbnail; Video lock/unlock; Slides play function.
Image review:
Press "REPLAY" first, in this state, press ◄/►key to browse photos
and videos in SD card.
Scale, move photos and Sudoku:
When browsing photos, press "ZOOM" first, and then press ▲/▼
key to mitigate or amplify photos. When amplified to the minimum,
photos will show with Sudoku style.
When amplifying photos, press "MOVE" first, then press
▲/▼/◄/► key for details of a picture.
Continuously press "ZOOM/MOVE" key can realize switches
among "scale" and "move".
When at the Sudoku state, press ▲/▼/◄/► key to move at the
selected images quickly, then press "OK" key to look at the selected
image.
Video plays:
37
When browsing video documents, operation instructions will be
displayed at the bottom of the screen.
Press "OK" key to play or suspend video.
Press ▲/▼/ key to terminal video playing.
When pressing "、" key, video will speed forward or go back with 2
times, 4times, 8 times of the play speed.
Auto play:
All images will automatically be displayed with slide mode in a
continuous loop.
When at "REPLAY" condition, press "MENU" key and select "auto
play". Press◄/► key to set auto play time as 3, 5 or 8 seconds.
Note: In auto play mode, only the first image of a video is
displayed, not the whole video.
Images lock/unlock:
May lock the selected images, which cannot be deleted after locking;
only unlocked them first and then deleted.
When at "REPLAY" state, press "MENU" key, choose "image lock"
option, press", "keys to set "lock the present", "unlock the present",
"lock all", "unlock all".
Note: When at "REPLAY" state, the above functions all can be
back to the previous level by pressing "EXIT" key, press "CAMERA",
"VIDEO" keys will quickly exit "REPLAY" state, switch to camera
38
or video recording.
7.2 Detailed explanations for partial functions
7.2.1 Timer settings
Timer function can set cameras to work in particular times, beyond
these times the camera is in dormant state. Two time settings can be
made.
System default the timer:
Off，“00:00——00:00”
Off，“00:00——00:00”
Example: Set camera to operate at 8:00 to 10:00 am and 15:30 to
18:00 pm every day, the set is as follows:
On，“08:00——10:00”
On，“15:30——18:00”
7.2.2 Language
System language, users may choose, according to the language of
his country, the corresponding language version to purchase.
"English" is the system default language. Users may acquire the
language version number from official website.
7.3 Firmware Upgrades
Manufacturer reserve the right of upgrading the product hardware
39
and software. User may update camera software version through SD
card (SD card capacity shall less than 32GB).
Please conduct firmware upgrade of product with the following
procedures:
1. Prepare a formatted SD card;
2. Copy the new version software document named
"FWD3A.bin" to SD card root catalog.
3. Insert SD card into camera, dial ON/OFF key to TEST
mode while pressing OK key, loosen "OK" key when the
blue indicator light is flashing;
4. The blue light flashes continuously and the screen is off,
indicating that the upgrade is in progress. Please don't
power off! Such as power off, you must re-insert the
upgrade software SD card, re-power, and dial the "open
key" to "TEST" test preview mode.
5. Reboot and see if the new version number is in accordance
with the version number before upgrading, to determine if
the upgrade is successful.
7.4 Frequently Asked Questions
7.4.1 Camera cannot start normally
No batteries;
Batteries are not installed correctly;
Run out of battery;
Batteries do not comply with specifications;
40
Not tune function switch to ON state yet;
Not insert SD card yet;
SD card is full loaded or damaged.
SD card capacity has surpassed the maximum support
capacity 64GB;
PIR sensor sensitivity setting grade is too low.
7.4.2 If the camera cannot get the remote picture and
information
SIM card contact is bad, the installation is not in place;
SIM card has no sufficient funds;
The location has no signal;
Battery capacity is insufficient;
Network setting parameters are incorrect;
Turn off interval sending time duration option.
7.5 Factory default settings
Camera f
actory settings parameter
Image
Shooting Mode
Camera
Photo Size 12MP
Video Size 1080P
Shooting
No. 1
Video L
ength
5 seconds
Setting
Device No. BUSH
41
Timer Off
PIR Interval
3 seconds
Time L
apse
Off
Stamp
s On
Power S
aving
Off
Auto Power Off 1 minute
Record Audio On
PIR Level Normal
Send
ing Interval
10 minutes
Network Info
Network configuration
Networks
Search for signal
IMEI
Identify number
of 3G module
System
Format SD card
Date and Time: 2017/01/01 00:00
Default Set
Factory
Language
English
Beep
Sound On
Loop
Record
ing
On
TV Mode PAL Mode
Password set 1234
Software Ver. G3
___01_6.
1.01
XII. Warranty Policy
We value our customers very highly and would like to ensure that
our products and service are always of a top standard. However, if
you are experiencing issues with your Bushwhacker products, please
take a moment to read through the information below to establish
42
whether your products are covered under the warranty.
WA R RA N T Y
We guarantee our Bushwhacker cameras to be free of defects in
materials and workmanship under normal use and service for a
period of a limited times after registered date of purchase.
EXCLUSIONS
This warranty does not cover damages caused by misuse, abuse,
improper handling or installation, or improper storage conditions
and natural disasters, by user installed batteries, or by repair
attempts of someone other than our authorized technicians, nor does
cover loss or theft.
This warranty extends solely to failures due to defects in materials or
workmanship under normal use. It does not cover normal wear of
the product. The camera manufacturer can provide extra service for
your camera after the warranty expiration, but the customer have to
be responsible for extra charges on parts, labor and shipping costs
therefore brought.
Please keep the warranty card for guarantee to keep in repair.
Please contact the regional distributor for more details.
43
XIII. Appendix I: Corresponding table of “video
length” and “time lapse” of taking photos
In video mode, the optional shortest duration of time lapse
depends on the length of the video.
The interval starts from the beginning of video length.
Video Length
Time Lapse
(The shortest duration)
5s 15s
10s 30s
15s 30s
20s 30s
30s 1m
45s 1m
1m 2m
2m 5m
3m 5m
5m 10m
10m 20m
44
XIV. Appendix II: Standard Packing List
Component name Quantity
Camera 1
USB cable 1
Aerials 1
TV Connecting wire 1
Installation bandage 1
Operating Instructions 1
Warranty Card 1
XV. Statement
1. The manufacturer reserves the right to make corrections at any
time to the contents of this manual due to inconsistencies in
editing / typographical errors and product upgrades and includes
modification in new version of the manual. These amendments
are without notice.
2. The manufacturer is not responsible for any illegal use; please
comply with local legal permission.
3. The manufacturer is not responsible for any data loss of the
user.
4. The manufacturer is not responsible for any damages or
casualties caused by the user's misuse of the product.
Loading...