Bushnell 119455, 119435, 119445 User Manual

TROPHY CAM

™

I NS TR UC TI ON M AN UAL

Model#s: 119435 / 119445 / 119455

Lit# 98-1517 / 1-10

2

TABLE OF CONTENTS PAGE #

ENGLISH

FrANçAIS

ESPAñOL

DEuTSCH

ITALIANO

POrTuGuêS

5-31

32-64

65-97

98-133

134-166

167-199

3

IMPORTANT NOTE

Congratulations on your purchase of one of the best trail cameras
on the market! Bushnell is very proud of this little unit and we
are sure you will be pleased with it as well. We appreciate your
business and want to earn your trust. Please refer to the notes
below and the instructions in this manual to ensure that you are
completely satisfied with this product.

If your Bushnell Trophy Cam does not seem to be
functioning properly or if you are having photo/video quality
issues, please check the Troubleshooting/FAQ section
on pages 25-28.
Problems are often due to something simple that was
overlooked, or require only changing one setting to solve.

If your problem continues after trying the solutions in
the Troubleshooting/FAQ section, please call Bushnell
Customer Service at [phone]. In Canada, call (800)
361-5702.

Bushnell recommends using 8 Energizer® Lithium AA batteries in

all Trophy Cams to obtain maximum battery life

Bushnell recommends using SanDisk® SD and SDHC Cards

(up to 16GB capacity) in all Trophy Cams

ENGLISH

INTRODUCTION

About the Trophy Cam

The Bushnell Trophy Cam is a digital scouting camera. It can be triggered
by any movement of game in a location, detected by a highly sensitive
Passive Infra-Red (PIR) motion sensor, and then take high quality pictures
(up to 8MP still photos), or video clips.

The Trophy Cam consumes very little power (less than 300μA) in a stand­by (surveillance) state. This means it can deliver up to six months stand-by
operation time when the device is powered by eight AA alkaline batteries,
and up to twelve months utilizing lithium AA batteries. Once motion in the
monitored area is detected, the digital camera unit will be triggered at once
(typically within one second) and then automatically take photos or videos
according to previously programmed settings. The Trophy Cam is equipped
with built-in infrared LEDs that function as a flash, so that it delivers clear
photos or videos (in black & white) even in the dark, and it can take color
photos or videos under sufficient daylight. The Trophy Cam is designed for
outdoor use and is resistant against water and snow.

Applications

The Trophy Cam can be used as a trail camera for hunting or scouting
game. It is also suitable for surveillance usage.

PARTS AND CONTROLS

The Trophy Cam provides the following connections for external devices:
USB port, SD card slot, TV Out, and external DC power in (Fig. 1).

A 3-way power switch is used to select the main operating modes: OFF,
SETUP, and ON (Fig. 2).

A control key interface with six keys is primarily used in SETUP mode to
select operational functions and parameters. As shown in Fig. 2, these keys
are: UP, DOWN, LEFT, RIGHT, OK and MENU. Four of the keys can also
perform a second function (shortcut operations in SETUP mode) in addition

5

to their main function: The DOWN key can be used to set the camera to
Photo mode (still camera icon), and the UP key can set the camera to Video
mode (movie camera icon). The RIGHT key also serves as the manual shutter
(“SHOT”) button of the camera and the OK key switches the camera to
the Playback (“REPLAY”) mode. These secondary functions are indicated by
icons or text above the key as shown in Fig. 2.

FRONT VIEW

LED IR Flash

Motion/ Low Battery Indicator

Lens

Lock Hole

TV Out

PIR Sensor

USB Port

Fig. 1: Connections

LCD Screen

Power/Mode
Switch

6

DC In

ON
SETUP
OFF

SD Card Slot

Cable to Battery
Compartment

UP/Video

DOWN/Photo

LEFT

MENU

OK/Replay

RIGHT/Shot

Fig. 2: Button and
Switch Guide

INSTALLING THE BATTERIES AND SD CARD

Before you begin learning how to use your Trophy Cam, you will first need
to install a set of batteries and insert an SD card. Although that may only take
you a minute, there are some important notes about both batteries and SD
cards you should be aware of, so please take the time to read the following
directions and cautions:

Loading Batteries

After opening the two latches on the right side
of the Trophy Cam, you will see that the Trophy
Cam has eight battery slots. Starting at the top
of the battery compartment, slots 1, 2, 3 and 4
form one group, while slots 5, 6, 7 and 8 form
the other group, each providing 6 volts in parallel.
For maximum battery life, you should install a full
set of eight batteries. The Trophy Cam may also
be operated by just four batteries installed in
the top group only (see right), starting at slot 1.
Battery life will be shorter with 4 batteries, but
the camera will operate normally. Whether you use 4 or 8, be sure to insert
each battery with correct polarity (negative or “flat” end against the long
spring of each battery slot).
Bushnell recommends using eight new lithium AA (Energizer® brand) or
alkaline AA batteries. NiMh Rechargeable batteries can also be used, but
they might have a shorter life span due to their reduced efficiency over time
and at low temperature. It is also possible to use a lead-acid external battery cell

with 6V output or suitable AC adapter-see below for more details.

Using an External Power Source

Optionally, you can connect an external 6V DC power source to the “DC In”
jack at the bottom of the Trophy Cam. It is recommended to use a power
source with a current output greater than 1000mA. However, during bright
daytime operation when no flash is required, the Trophy Cam can function
with much less current (>400mA). Please use a compatible power source

(optional, user provided)

7

cable (not provided) to connect the external DC power source with the power
input jack of the Trophy Cam, making sure that the polarity is correct. Note:

The power connector is a 4.0x1.7mm coaxial DC power plug with positive
“tip” (inside pin) polarity (Radio Shack P/N 274-1532 or equivalent).

If both an external power source is connected and batteries are installed, the
Trophy Cam will be powered by the external power source.
When the batteries become weak, the low-battery indicator LED will glow
blue, indicating the batteries should be changed (pg 6, “Front View”).

Inserting the SD Card

The Trophy Cams have 32MB internal memory, which can hold only about
20 photos (@ 5MP resolution). This is handy for testing and getting familiar
with the camera, but you will no doubt want to leave the camera unattended
for longer than a day, so using an SD card is recommended. Insert the SD
card (with the camera’s power switch in the OFF position) before beginning
to operate the camera. Don’t insert or remove the SD card when the power
switch is in the ON position.
The Trophy Cam uses a standard SD (Secure Digital) memory card to save
photos (in .jpg format) and/or videos (in .asf format). SD and SDHC (High
Capacity) cards up to a maximum 16GB capacity are supported. Before
inserting the SD card into the card slot after opening the camera’s front
cover, please make sure that the write-protect
switch on the side of the card is “off” (NOT in the
“Lock” position). The following describes how to
insert and remove the SD card:

• Insert the SD card into the card slot with its

label side upwards (see above). A “click” sound
indicates that the card is installed successfully. If the wrong side of the
card is facing up, you will not be able to insert it without force-there is only
one correct way to insert cards. If the SD card is not installed correctly,
the device will not display an SD card icon on the LCD in SETUP mode
(the SD card icon displayed after switching to SETUP mode will have a “lock”
symbol inside it in it if the card is locked). Formatting the SD card by using
the Trophy Cam’s “Format” parameter before using it for the first time is
recommended, especially when a card has been used in other devices

8

(see “Changing Menu Parameter Settings” for details).

• To take out the SD card, just gently push in the card (do not try to pull it
out without pushing in first). The card is released from the slot and ready
to be removed when you hear the click.

Be sure the camera’s power is switched OFF

before inserting or removing SD cards or batteries.

WARNING

USING THE TROPHY CAM

Once you’ve prepared your Trophy Cam by properly installing batteries and
an SD card, you could simply take it outside, strap it to a tree, switch it on
and leave-and you might get some great photos that are exactly what you
wanted. However, we highly recommend that you first spend some additional
time indoors with this manual and your camera until you know a bit more
about what the 3-way switch and those control keys do. If nothing else, you’ll
probably want to at least set the date and time so the camera will imprint
them (or not-it’s your option) on your photos as they are taken, learn how to
set the camera to shoot video clips instead of still photos if you like, and read
some tips about mounting it on a tree.

THE OFF, ON, AND SETUP MODES

The Trophy Cam has three basic operational modes:

• OFF mode: Power switch in the OFF position.

• ON mode: Power switch in the ON position (LCD screen is off.)

• SETUP mode: Power switch at SETUP position (LCD screen is on).

OFF Mode

The OFF mode is the “safe” mode when any actions must be taken, e.g.,
replacing the SD card or batteries, or transporting the device. You will also

9

use OFF mode if you connect the camera to a computer’s USB port later
to download your photos/videos. And of course, when you are storing or not

using the camera, you will switch it to OFF. Please note that even in the OFF
mode the Trophy Cam still consumes power at a very low level. Therefore,
it’s a good idea to take the batteries out of the battery compartment if the
camera will not be used for a long time.

ON Mode

Anytime after the batteries and SD card have been inserted, you can switch
on the camera. When the power switch is moved to the top position, the
camera will enter into the ON (Live) mode. The motion indicator LED (pg. 5,
“Front View”) will blink red for about 10 seconds. This interval allows time for
you to close the Trophy Cam’s front cover, lock it, and leave the monitored
area. Once in the ON mode, no manual controls are needed or possible
(the control keys have no effect). The Trophy Cam will take photos or
videos automatically (according to its current parameter settings) when it is
triggered by the PIR sensor’s detection of activity in the area it covers.
You can either move the power switch directly from OFF to ON mode, or
stop at the SETUP position first to change one or more settings, then move
the switch to ON after you have finished doing so.

SETUP Mode

In the SETUP mode you can check and change the settings of the Trophy
Cam with the help of its built-in LCD (or a monitor connected to the TV out

jack). These settings, found in the SETUP Menu, let you change the photo
or video resolution, interval between photos, switch the time imprint on, etc.

Moving the power switch to the SETUP position will turn on the LCD display,
and you will see an information screen that shows how many images have
been taken, the battery level, camera or video mode, etc (see Fig. 3 below).

NOTE: always move the power switch from OFF to SETUP mode. It
is possible that the camera could lockup if it is switched from ON to
SETUP mode. If this occurs, simply move the switch to OFF and then
push it up to SETUP again.

10

Fig. 3: SETUP Information Screen (standard display model shown)

Image Size

SD Card Status

Camera Mode

Time Stamp

Battery Level

TV Status
Date:Month-Day-Year

Time
Hour:Minute:Second

Number of Images

Available Space

SETUP Mode Shortcut Keys/Functions

As mentioned earlier in “Parts & Controls”, four of the keys below the LCD
have secondary, “shortcut” functions when the camera is switched to
SETUP mode (but the MENU key has not been pressed):

• Press the UP key to quickly set the camera to shoot video clips.

• Press the DOWN key to quickly set the camera to take still photos.

• Press the RIGHT key to manually trigger the shutter. This is useful

for testing the camera-make sure you are in SETUP mode, press the
RIGHT key, and a few seconds later a photo or video (depending on
how the camera was set) will be saved to the SD card (or internal
memory if no card is inserted). The “number of images taken” counter
on the bottom left of the LCD will increase by one. If the display
indicates “SD PROTECTED” when you press the SHOT key, switch
the camera OFF, remove the SD card and slide its protect switch off.

• Press the OK key to replay (review or playback) photos/videos on
the LCD (color viewer models only), or a connected TV monitor (std.
display models). See “Playing Back Photos/Videos” for more details.

11

Using the SETUP Menu to Change Settings

The main purpose of the SETUP mode is to allow you to change the settings
of the camera’s parameters (12-13 different ones are available) so your
Trophy Cam operates exactly the way you want it to. You will do this by
entering the SETUP Menu and pressing the keys below the LCD display,
which will show you each parameter and its setting.

Changing Parameter Settings in SETUP Mode

A wide range of options or “parameters” are provided to allow you to set
the Trophy Cam to your operational preferences. To change the setting of
any parameter you must first switch to the SETUP mode. Once in SETUP
mode, pressing the MENU button will allow you to select any parameter and
change its setting. The name of the parameter and its current setting will be
shown on the LCD. Pressing the RIGHT or LEFT key scrolls to the next or
previous parameter (RIGHT key to move on to the next parameter and LEFT
key to go back to the previous parameter), and pressing the UP or DOWN
key lets you select a different setting for the currently displayed parameter.
Once you have selected your preferred new setting for a parameter, press
the OK button to save the new setting (actually change it). When have are
finished changing the settings of one or more parameters, press MENU
again to exit the SETUP menu. MENU can also be pressed anytime you
want to cancel changing a parameter’s setting after a new setting has been
selected (but OK has not been pressed yet). After setting the parameters
to your preferences, be sure to move the switch to ON to begin actually
taking photos or videos. No images will be captured if the switch is left in the
SETUP position (unless you press the RIGHT/Shot key after exiting the menu)­in fact, the camera will power off automatically after a few seconds with no
key pressed.

Color Viewer vs. Standard Display Models

There is a slight difference in how the settings for a parameter are shown
between the two different types of Trophy Cam models:

• On models with a color viewer, all the available settings for the currently
displayed parameter are shown on one screen, with a checkmark next

12

to the current setting (Fig. 4a). To change the setting, first use the UP/
DOWN keys to highlight (select) the new setting you want (Fig. 4b), then

press OK to “Execute” the actual change to the selected setting. The
checkmark will appear next to your new setting to confirm this (Fig. 4c).

• On models with standard (non-color) display, only one setting is displayed
at a time, starting with the current setting for the parameter when it is
first selected (Fig. 4d). To change the setting, use the UP/DOWN keys
to display the new setting you want (Fig. 4e), then press OK to “Execute”
(make the actual change to this setting). If you want to confirm this setting
is now the current one, just press the RIGHT key to scroll to the next
parameter, then press LEFT to go back again to the previous one. You
should see the parameter setting you just made.

Fig. 4: Selecting Parameter Settings

COLOR VIEWER

(4a)

(4b)

(4c)

STANDARD DISPLAY

Press MENU

(4d)

Press DOWN

(4e)

Press OK

13

EXAMPLES-Changing the Settings of Some Common Parameters

Following this page, you will find tables listing all of the parameters found in
the SETUP Menu, along with their possible settings (or range of settings),
and a detailed description of what the parameter controls and what
the settings do. If you read the previous section detailing how to select
parameters and change their settings, you should be able to dive right in, find
the parameter(s) you want, and setup the camera to your preferences. But
maybe you’d rather walk through an example or two first:

To change any parameter’s setting, always start with the power switch in the
SETUP position. After the LCD comes on, press the MENU key.

The first parameter you will when you first enter the SETUP Menu is “Mode”.
To change it from its default setting of “Camera” (still photos) to “Video”
(shoot video clips), press the DOWN key to highlight “Video” (color viewer
models) or to select the “Video” setting (std. display models). Press the OK
key to “Execute” (Set) the new setting you’ve selected for this parameter.

Now press the RIGHT key to move to another parameter in the Menu.
Pressing it four times will take you to “Video Length”. Try using the UP and
DOWN keys to scroll through the range of settings, then press OK to lock in
your setting for the length of each video clip the camera shoots.

Pressing the RIGHT key several more times will get you to the “Default Set”
parameter. Highlight or select “Execute” (using UP or DOWN) and press OK
to restore all parameters (including the Mode and Video Length parameters
you changed a minute ago) back to their original factory default settings. The
default settings for each parameter are indicated in bold type in the SETUP
Menu tables on the next several pages.

Be sure to set the current date and time, using the “Set Clock” parameter,
if you choose to change the “Time Stamp” parameter setting to “On” since
that will tell the camera to imprint the date and time on each of the images
it captures.

14

The SETUP Menu – Parameters and Settings List w/Descriptions

Parameter

Mode

Image Size

(only aects
still photos)

Capture
Number

(only aects
still photos)

Video Size

(only aects
video clips)

Video
Length (only

aects video
clips)

Settings

(Bold=default)

Camera or

Video

5M Pixel, 8M
Pixel, 3M Pixel

1 Photo, 2
Photo, 3 Photo

640x480,
720x480,
320x240

10S (second)
default, with
60S to1S
possible range

Description

Selects whether still photos or
video clips are captured when the
camera is triggered.

Selects resolution for still photos
from 3 to 8 megapixels. Higher
resolution produces better quality
photos, but creates larger files
that take up more of the SD card
capacity (fills up faster). 5M is a
good compromise between quality
and file size.

Selects how many photos are
taken in sequence per trigger in
Camera mode. Please also refer to
the Interval parameter.

Selects video resolution (in pixels
per frame). Higher resolution
produces better quality videos, but
creates larger files that take up
more of the SD card capacity (fills
up faster). 640x480 is VGA video
in standard 4:3 format, 720x480 is
widescreen format.

Sets length per captured video
clip. Settings begin with 10 second
default when parameter is first
selected. After stepping down to
1S, video length settings start over
at 60S.

15

Parameter

Interval

Sensor
Level

Settings

(Bold=default)

10S (second)

default,
with a 60M
(minute) to1S
(second) range
of settings
available.

(60M-1M are set
in one minute
increments,
59S-1S are set
in one second
increments)

Normal, High,
Low

Description

Selects the length of time that the
camera will “wait” until it responds
to any additional triggers from the
PIR after an animal is first detected
and remains within the sensor’s
range. During this user set “ignore
triggers” interval, the camera will
not capture photos/videos. This
prevents the card from filling up
with too many redundant images.
Settings begin with 10 second
default when parameter is first
selected. Note: after setting down

past “1S”, settings start over at “60M”.

Selects the sensitivity of the PIR
sensor. The “High” setting will
make the camera more sensitive
to infrared (heat) and more easily
triggered by motion, and the “Low”
setting makes it less sensitive to
heat and motion. The High setting
can be useful when the ambient
temperature is warm (making it
more difficult for the sensor to
detect animals), and the Low
setting may help in cold weather if
the camera is being triggered too
often by anything warmer than the
surroundings.

16

Parameter

Settings

(Bold=default)

Format Execute

(followed by an
additional No/
Yes step on color
viewer models
only)

TV Out

Time Stamp

NTSC, PAL

Off, On

(only aects
still photos)

Set Clock Set

Description

Deletes (erases) all files stored
on a card to prepare it for reuse.
Always format a card that has been
previously used in other devices.

Caution! Make sure you have
downloaded and backed up any
files you want to preserve first!

Press OK to execute (then select Yes
and press OK again on color viewer
models), press MENU (or select
NO then press OK) to exit without

formatting.

Selects video standard /format for
the “TV Out” output jack. The video
standard is NTSC for the United
States, Canada, Mexico, Asia and
South America. PAL is used primar­ily in Europe.

Select “On” if you want the date &
time (that the photo was captured)
imprinted on every photo, select
“Off” for no imprint.

Press OK and use the UP/DOWN
keys (to change the setting) and
LEFT/RIGHT keys ( to move
to the next field) to set the hour

(24-hr format only, “00”=midnight,
“12”=noon) and minute, and then

(on the lower row), the year, month
and date.

17

Parameter

Default Set

Settings

(Bold=default)

Cancel,

Execute

Description

Select “Execute” and press OK
to restore all parameters to the
original factory default settings. If
the camera is behaving oddly and
you think you may have changed
the setting for something accidently
(but aren’t sure which one), this
will reset all parameters to their
most commonly used or “generic”
settings.

18

MOUNTING AND POSITIONING THE TROPHY CAM

Mounting

After you’ve set up the camera’s parameters to your personal preferences
at home or in your truck, you’re ready to take it outside and slide the power
switch to “ON”. When setting up the Trophy Cam for scouting game or
other outdoor applications, you must be sure to mount it in place correctly
and securely. We recommend mounting the Trophy Cam on a sturdy tree
with a diameter of about 6 in. (15cm). To get the optimal picture quality,
the tree should be about 16-17 ft. (5 meters) away from the place to be
monitored, with the camera placed at a height of 5-6.5 ft. (1.5~2 m). Also,
keep in mind that you will get the best results at night when the subject is
within the ideal flash range, no farther than 45’ (14m) and no closer than 10’
(3m) from the camera.

There are two ways to mount the Trophy Cam: using the provided adjustable
web belt, or the tripod socket.

Using the adjustable web belt: Fig. 5 illustrates using the web belt on
the Trophy Cam. Push one end of the belt through the two brackets on
the back of the Trophy Cam. Thread one plastic buckle part onto each
end of the belt. Fasten the belt securely around the tree trunk by clicking
the buckle ends together after tightening the belt so there is no slack left.

Fig. 5: Attaching the Belt

19

Using the tripod socket: The camera is equipped with a socket at the
bottom end to enable mounting on a tripod or other mounting accessories
with a standard1/4-20 thread.

Two optional mounting accessories, a “Bear Safe” metal camera box
(model # 19653C) and Deluxe Tree Bracket (model# 119652C) are also
available-please see your Bushnell dealer or website for more details.

Sensing Angle and Distance Test

To test whether the Trophy Cam can effectively monitor the area you
choose, this test is recommended to check the sensing angle and monitoring
distance of the Trophy Cam. To perform the test:

• Switch the Trophy Cam to the SETUP mode.

• Make movements in front of the camera at several positions within

the area where you expect the game or subjects to be. Try different
distances and angles from the camera.

• If the motion indicator LED light blinks, it indicates that position can be
sensed. If it does not blink, that position is outside of the sensing area.

The results of your testing will help you find the best placement when
mounting and aiming the Trophy Cam. The height away from the ground for
placing the device should vary with the animal size appropriately. In general,
3 to 6 feet is preferred.
You can avoid potential false triggers due to temperature and motion
disturbances in front of the camera by not aiming it at a heat source or nearby
tree branches or brush (especially on windy days).

Switching ON the Camera

Once you switch to the ON mode, the motion indicator LED (red) will blink
for about 10 seconds. This gives you time to close and lock the front cover of
the Trophy Cam and then walk away. During this time, the motion indicator
LED will blink red continuously. After it stops blinking, the PIR is active, and
any motion that is detected by it will trigger the capture of photos or videos
as programmed in the SETUP Menu. Be sure you have read the descriptions
of the Capture Number, Video Length, Interval and Sensor Level parameters.

20

Please note, the PIR is strongly sensitive to ambient temperature. The greater
the temperature difference between the environment and your subject, the
farther the possible sensing distance. The average sensing distance is about
45 ft.

Before leaving the camera unattended, please check for the following:

• Are the batteries or DC power supply inserted/connected with correct
polarity and is the power level is sufficient?

• Does the SD card have sufficient available space and is its write­protection (lock) switch off?

• Is the Power switch in the ON position? (do not leave it in SETUP).

PLAYING BACK/DELETING THE PHOTOS/VIDEOS

After you have setup, mounted and activated your Trophy Cam, you will of
course be eager to return later and review the images it has captured for
you. There are several different ways this can be done.

Reviewing Images on the Trophy Cam LCD (Models with Color Viewer only)

• Put the power switch in SETUP mode (switch to OFF first).

• Push the OK(Replay) key to enter image review mode.

• Use the UP/DOWN keys to scroll through your photos or videos. The

right corner of the display will indicate “JPG” for still photos, and a film
icon for video files. Press the RIGHT(Shot) key to review a video.

• Push MENU to delete an image. Image delete mode works as
described below. To exit image review mode, press the OK key.

Reviewing Images on an External Video Monitor

A TV monitor can also be used to play back pictures (or videos) from the
device. Connect a TV monitor or a viewing device (such as a digital picture
frame) that has a standard composite video input (RCA jack) to the Trophy
Cam ‘s “TV Out” mini jack using the supplied cable. Then:

• Put the power switch in SETUP mode (switch to OFF first).

• Press the OK key. The most recently captured image will be shown

21

on the video monitor. For video clips, press the
SHOT (RIGHT) key to start playing, press again
to stop.

• Press the UP key for the previous photo or video
and the DOWN key for the next one. When
viewing images, the total number of all images
in the SD card and the index of the displaying
image are shown in the center of LCD and at the
bottom of the video monitor respectively.

• Press the OK key to return to live preview state
(SETUP mode) when playback is finished.

Cable from “TV

Out”

Deleting Photos or Videos

If you see a photo or video during playback on the LCD or video monitor
that you want to delete, it can be done easily without leaving SETUP mode:

• Press the MENU key. You will see the first “Delete” screen, which lets
you selects the option to delete only the currently displayed photo/
video, or all photos/videos (see below).

• Highlight the “Delete Current” or “Delete All” option, then press OK.

• Next, select “Yes” and press OK to erase only the last displayed photo

or video (if you selected “Delete Current”), or every photo and video file
on the card (if you selected “Delete All”)-or select “No” and press OK
to cancel the operation without deleting any files.

NOTE: after deleting a picture or a video file, the deleted files can’t be restored!
It is also possible to delete all files from the card by using the Format parameter.

Reviewing Images Directly From the SD Card

This is the most popular method of viewing images. Since unmounting the

22

camera and taking it to your computer isn’t very convenient, you may find it
easier to just take the card out. By removing the SD card (swapping it for a
new empty card if you like) and taking it to your home or campsite to view
the images by using an SD card “reader” (user supplied) connected to your
computer (some computers and TVs have a built in SD card slot), you can
leave the camera in place ready to capture more images. Once connected,
the card reader works the same way as described below-please read that
section if you have any problem finding your files.

Reviewing Images by Connecting the Camera to a Computer

You can always unmount the entire camera from the tree and connect its
USB port to a computer-it will be recognized as a “removable disk”, without
the need to install any drivers or software. When using a PC (or Mac*) to view
photos (or video clips*), first connect the device to the computer with the
supplied USB cable. Then use commercial software with an image browser
feature, or an image browser included with the PC’s operating system to
view images saved on the SD card in the folder \DCIM\100EK113. Each
new image or video will be numbered incrementally in order of the time it was
captured. For example, you will see file names such as “PICT0001.JPG” or
“PICT0001.ASF”. Through the file format suffix you can distinguish whether
the file is a still photo (with suffix .jpg) or a video (with suffix .asf).

*“.ASF” video files may require additional software for viewing on a Mac.

The Trophy Cam supports 3 kinds of file system formats, FAT12, FAT16,
and FAT32. The default value is FAT16 to save photos and videos. Here are
some related notes:

• You don’t need to be concerned about the file system format of the
Trophy Cam unless your equipment has problems reading the SD
card. If this happens, please format the SD card with the Trophy Cam
or in your computer first and then insert the card into your Trophy Cam
and try again.

• The default file system format of the Trophy Cam is FAT16, which most
computers can read. If you format an SD card for the Trophy Cam
in your computer, you should choose the file system format FAT16.
Normally FAT16 is recommended unless you have another image
viewer that uses FAT12 or FAT32 format.

23

DOWNLOADING THE PHOTOS/VIDEOS

To download your photos/videos to a PC or Mac*, first make sure the Trophy
Cam power switch is in the OFF position. Connect the supplied cable to the

camera’s USB port, then directly to a main USB port on your computer-do
not use front panel/keyboard USB ports or unpowered “hubs”.
The Trophy Cam will be recognized as a standard “USB Mass Storage”
device (this may take several seconds the first time you connect it). If you
would rather leave your camera in the woods and just pull its SD card out, an
SD card reader works the same way as described in this section once the
card is inserted and the reader is connected to your computer.

With Windows XP or later, you can then simply use the options in the pop­up window to copy, view, or print your photos (right).

On all Windows OS, the Trophy Cam will also be
listed as a “Removable Disk” if you open the “My
Computer” window (on Macs, an icon will appear
on your desktop). The Trophy Cam’s photo files are
named “PICT0001.JPG” etc, and are located in the
“DCIM\100EK113” folder on this “Removable Disk”.
Video file names will end with “.ASF”. You may copy the photos/videos to
your hard drive as you would any file-just copy/paste or drag the file names
or icons to your drive or desktop.

After the photos are copied to your hard drive, you can disconnect the
Trophy Cam. (On Mac computers, drag the “disk” that appeared on your
desktop when the camera was connected into your Trash to “eject” it before
disconnecting.) The .jpg standard files from the Trophy Cam may be viewed
and edited with any photo software you choose to use. The .asf video files
may be viewed with Windows Media Player (version 7 or later) as well as
other video playback programs that may have been supplied with your
computer, or are available online.

* “.ASF” video files may require additional software for viewing on a Mac.

24

TROUBLESHOOTING / FAQ

Battery life is shorter than expected

1. Battery life will vary with operating temperature and the number of

images taken over time. Typically, the Trophy Cam will be able to
capture several thousand images before the batteries die.

2. Check to make sure you have used new alkaline or lithium batteries.

Bushnell recommends using 8 Energizer
in all Trophy Cams to obtain maximum battery life.

3. Make sure that the power switch was turned to the “On” position
and that the camera was not left in “Setup” mode while in the field.

4. Make sure that you are using a good quality name brand SD card in
your camera. Bushnell recommends SanDisk
up to 16GB. Our experience indicates that poor quality SD cards
can sometimes reduce your Trophy Cam battery life.

Camera stops taking images or won’t take images

1. Please make sure that the SD card is not full. If the card is full, the
camera will stop taking images.

2. Check the batteries to make sure that they are new alkaline or lithium
AA batteries. See note above about short battery life.

3. Make sure that the camera power switch is in the “On” position and
not in the “Off” or “Setup” modes.

4. Make sure that you are using a good quality SD card in your camera.

Bushnell recommends SanDisk

5. If the SD card has its write protect switch in the lock position, the
camera will not take images.

6. If you have used an SD card in another device before inserting it in
your Trophy Cam, you might want to try formatting the card using
the “Format” parameter in Setup mode (make sure you have backed
up any important files first, as formatting will erase all previous files).
In some cases, other devices may change the formatting of the SD
card so that it will not work properly with the Trophy Cam.

®

®

Lithium AA batteries

®

brand SD Cards

SD Cards up to 16GB.

25

Camera won’t power up

1. Make sure that you have installed at least 4 batteries (the
required minimum #) in the battery compartment, starting at the
top, filling battery spaces 1-4 with no “gaps”.

Bushnell recommends using 8 Energizer® Lithium AA batteries
in all Trophy Cams.

2. Make sure that the batteries are installed correctly, observing
proper polarity. Always place the negative (flat) end of each
battery in contact with the spring side of its slot inside the
camera.

3. After moving the switch from “Off” to “Setup” or “On”, make
sure that the switch is correctly in position to ensure the proper
mode (avoid positions “between” two modes).

4. Do not move the switch directly from “On” to “Setup”-always
move the switch all the way down to “Off” first, then back up
to “Setup”.

Still Photo and/or Video Quality Problems

1. Night photos or videos appear too dark

a. Check the battery indicator icon to see if battery power is
full. The flash will stop operating near the end of the battery life.
b. You will get the best results when the subject is within the
ideal flash range, no farther than 45’ (14m) from the camera.
Subjects may appear too dark at greater distances.
c. Please note that when the Capture Number parameter is
set higher than “1 Photo”, or with very short Interval settings,
some images may appear darker than others due to the quick
response and rapid retriggering of the camera, allowing less
time for the flash to fully recharge before firing again.

2. Daytime photos or videos appear too dark

a. Make sure that the camera is not aimed at the sun or other
light sources during the day, as this may cause the auto exposure
to produce darker results.

3. Night photos or videos appear too bright

26

a. You will get the best results when the subject is within the
ideal flash range, no closer than 10’ (3m) from the camera.
Subjects may appear too light at closer distances.

4. Daytime photos or videos appear too bright

a. Make sure that the camera is not aimed at the sun or other
light sources during the day.

5. Photos with streaked subject

a. In some cases with low lighting conditions and fast moving
subjects, the 5MP or 8MP resolution settings may not perform
as well as the 3MP setting.
b. If you have multiple images where fast moving subjects
produce streaks on the photo, try the 3MP setting instead.

6. Red, green or blue color cast

a. Under certain lighting conditions, the sensor can become
confused resulting in poor color images.
b. If this is seen on a consistent basis, then the sensor may
need servicing. Please contact Bushnell customer service.

7. Short video clips—not recording to the length set

a. Check to make sure that the SD card is not full.
b. Make sure that the camera has good batteries in it. Near the
end of the battery life, the camera may choose to record shorter
video clips to conserve power.

Date/Time Stamp not appearing on images

1. Make sure that the “Time Stamp” parameter is set to “On”.

Photos Do Not Capture Subject of Interest

1. Check the “Sensor Level” (PIR sensitivity) parameter setting.

For warm environmental conditions, set the Sensor Level to “High”
and for cold weather use, set the sensor for “Low”.

2. Try to set your camera up in an area where there is not a heat source
in the camera’s line of sight.

3. In some cases, setting the camera near water will make the camera
take images with no subject in them. Try aiming the camera over
ground.

27

4. Try to avoid setting the camera up on small trees that are prone to
being moved by strong winds.

5. Remove any limbs which are right in front of the camera lens.

PIR Sensor LED Flashes/Doesn’t Flash

1. When the camera is in the “Setup” mode, a special LED on the front
of the camera will flash when it senses motion. This is for setup
purposes only and will help the user aim the camera.

2. During use, the LED will not flash when the camera takes an image.
This is to help keep the camera hidden from game.

LCD Screen Issues

1. LCD screen powers on but no text is present.

a. After moving the switch from “Off” to “Setup” or “On”, make sure
that the switch is correctly in position to ensure the proper mode
(avoid positions “between” two modes).
b. Do not move the switch directly from “On” to “Setup”-always
move the switch all the way down to “Off” first, then back up to
“Setup”.

2. LCD screen shows a faint black line after turning from “Setup” to “On”.

a. The LCD will turn off when you slide the switch to the “On”
position. In some cases, this black line will appear and then fade in
about 1 second. This is normal and the camera will function properly.

3. Screen comes on but then powers off

a. Make sure that you have installed the SD card correctly.

Camera won’t retain settings

1. Make sure that you have been saving the changes to any parameter
settings that you made while in Setup mode, by pressing “OK” after
changing the setting. If you don’t save your new setting after changing
it, the camera will continue to use the original default setting for that
parameter.

28

TECHNICAL SPECIFICATIONS

Image Sensor

Maximum Pixel Size

Lens

IR-Flash Range

Display Screen

Memory Card

Internal RAM

Picture Size

Video Size

PIR sensitivity

Operation

Response Time

Triggering Interval

Shooting Numbers

Video Length

Power Supply

Stand-by Current

Power Consumption

User Interface

Interface

Security
Operating

Temperature

Operating Humidity

Security
authentication

5 Megapixel Color CMOS

3264x2448 (8MP)

F=3.1; FOV=50°; Auto IR-Cut-Remove (at night)

36’-45’ (12m-15m)

Std B&W Display: 24x32mm(1.5”) ; Color Display:
32x42mm (2”)

SD or SDHC Card, Maximum capacity 16GB

32MB
8MP = 3264x2448; 5MP = 2560x1920; 3MP =

2048x1536
720x480/30 fps, 640x480/30fps, 320x240/30fps

PIR with 3 sensitivity levels: High/Normal/Low

Day/Night

1s

1sec. - 60min. programmable

1— 3 programmable

5-60sec. programmable

8xAA recommended, 4xAA as emergency power

< 0.3mA(<7mAh/day)

200mA (+530mA when IR-LED lighted)

LCD display
TV out (NTSC/PAL); USB; SD card holder; 6V DC

external
Strap; ¼-20 attachment

-20 - 60°C (Storage temperature: -30 - 70°C)

5% - 90%

FCC/CE/RoHs/WEEE

29

TWO-YEAR LIMITED WARRANTY

Your Bushnell® product is warranted to be free of defects in materials and
workmanship for two years after the date of purchase. In the event of a defect under
this warranty, we will, at our option, repair or replace the product, provided that you
return the product postage prepaid. This warranty does not cover damages caused
by misuse, improper handling, installation, or maintenance provided by someone
other than a Bushnell Authorized Service Department.

Any return made under this warranty must be accompanied by the items listed
below:

A check/money order in the amount of $10.00 to cover the cost of postage

1)

and handling

2) Name and address for product return

3) An explanation of the defect

4) Proof of Date Purchased

5) Product should be well packed in a sturdy outside shipping carton, to prevent

damage in transit, with return postage prepaid to the address listed below:

IN U.S.A. Send To: IN CANADA Send To:
Bushnell Outdoor Products Bushnell Outdoor Products
Attn.: Repairs Attn.: Repairs
8500 Marshall Drive 25A East Pearce Street, Unit 1
Lenexa, Kansas 66214 Richmond Hill, Ontario L4B 2M9

For products purchased outside the United States or Canada please contact your
local dealer for applicable warranty information. In Europe you may also contact
Bushnell at:

Bushnell Germany GmbH
European Service Centre
Mathias-Brüggen-Str. 80
D-50827 Köln
GERMANY
Tel: [phone]
Fax: [phone]

You may have other rights which vary from country to country.

This warranty gives you specific legal rights.

©2010 Bushnell Outdoor Products

Specifications and designs are subject to change without any notice
or obligation on the part of the manufacturer.

30