Bush Hog RMB 1445 User Manual

RMB1445

BOOM MOWER

HYDRAULIC BOOM CUTTER

Published 03/11

PART'S MANUAL

SECTION 91

©2009 Alamo Group Inc.

PARTS ORDERING GUIDE

The following instructions are offered to help eliminate needless delay and error in pro­cessing purchase orders for the equipment in this section.

1. The Parts Section is prepared in logical sequence and grouping of parts that belong
to the basic machine featured in this manual. Part Numbers and Descriptions are given
to help locate the parts and quantities required.

2. The Purchase Order must include the name and address of the person or organiza­tion ordering the parts, who should be charged, and if possible, the serial number of the
machine for which the parts are ordered.

3. The Purchase Order must clearly list the quantity of each part, the complete and correct
part number (be sure to include all periods), and the basic name of the part.

4. The Manufacturer reserves the right to substitute parts where applicable.

5. Some parts are unlisted items which are special production items not normally stocked
and are subject to special handling. Request a quotation for such parts before sending
a Purchase Order.

6. The Manufacturer reserves the right to change prices without prior notice.
For maximum safety and to guarantee optimum product reliability, always

use genuine BUSH HOG Parts. The use of inferior replacement parts may
causepremature or catastrophic failure which could result in serious injury
or death.Direct any questions regarding parts to:

BUSH HOG

2501 Griffin Ave.
Selma, AL 36703
www.bushhog.com
Contact Us
800-304-2836

To the Owner/Operator/Dealer

All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded
operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has
designed this implement to be used with all its safety equipment properly attached to minimize the chance of
accidents.

BEFORE YOU STAR T! Read the safety messages on the impl ement and shown in your manual. Observe the rules
of safety and common sense!

WARRANTY INFORMATION:
Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty RegistrationForm in
full and return it to within 30 Days. Make certain the Serial Number of the Machine is recorded on theWa rranty Card and
on the Warranty Form that you retain.

LIMITED WARRANTY

2222222222222222222222222222222

Bush Hog warrants to the original purchaser of any new Bush Hog equipme nt, purchas ed from an au thorized Bush
Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for
non-commercial, state and municipalities’ use and ninety (90) days for commercial use from date of retail sale. The
obligation of Bush Hog to the purchaser under this warranty is limited to the repair or replacement of defective
parts.

Replacement or repair parts installed in the equipment covered by this limited warranty are warranted for ninety
(90) days from the date of purchase of such part or to the expiration of the applicable new equipment warranty
period, whichever occurs later . Warranted parts shall be provided at no cost to the user at an authorized Bush Hog
dealer during regular working hours. Bush Hog reserves the right to inspect any equipment or parts which are
claimed to have been defective in material or workmanship.

DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES

Bush Hog’s obligation under this limited warranty, to the extent allowed by law , is in lieu of all warranties, implied or
expressed, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE and any liability for incidental and consequential damages with respect to the sale or
use of the items warranted. Such incidental and consequential damages shall include but not be limited to:
transportation charges other than normal freight charges; cost of installation other than cost approved by Bush
Hog; duty; taxes; charges for normal service or adjustment; loss of crops or any other loss of income; rental of
substitute equipment, expenses due to loss, damage, detention or delay in the delivery of equipment or parts
resulting from acts beyond the control of Bush Hog.

THIS LIMITED WARRANTY SHALL NOT APPLY:

1. To vendor items which carry their own warranties, such as engines, tires, and tubes.

2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident.

3. If parts not made or supplied by Bush Hog h ave been us ed in connection with the unit, if, in the sole judgement
of Bush Hog such use affects its performance, stability or reliability.

4. If the unit has been altered or repaired outside o f an authorized Bush Hog de alership in a man ner which, in the
sole judgement of Bush Hog, affects its performance, stability or reliability.

5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic fluid, worn
blades, or to normal deterioration of such things as belts and exterior finish due to use or exposure.

6. To expendable or wear items such as teeth, chains, sprockets, belts, springs and any other items that in the
company’s sole judgement is a wear item.

NO EMPLOYEE OR REPRESENTATIVE OF BUSH HOG IS AUTHORIZED TO CHANGE THIS LIMITED
WARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE IN
WRITING AND SIGNED BY BUSH HOG’S SERVICE MANAGER, 2501 GRIFFIN AVE., SELMA, ALABAMA

36703.

2222222222222222222222222222222

Record the model number, serial number and date
purchased. This information will be helpful to your
dealer if parts or service are required.

MAKE CERTAIN THE WARRANTY
HAS BEEN FILED WITH BUSH HOG
SELMA, ALABAMA

MODEL NUMBER ________________________________
SERIAL NUMBER ________________________________
DATE OF RETAIL SALE ___________________________

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

MARCH, 2011

ALPHABETICAL INDEX

RMB1445 BOOM MOWER

ITEM PAGE NUMBER

Cab Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-1

Control Valve Assy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-2, 91-1-3

Cutterbar - Sheartrim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-22

Decals - Bush Hog Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-24

Dipper - Lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-10, 91-1-11

Dipper - Upper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-12

Flail Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-20, 91-1-21

Gearbox and Pump Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-6, 91-1-7

Guard Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-23

Hydraulic Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-5

Hydraulic Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-4

Lift Float Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-25

Mainframe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-13

Mainframe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-16, 91-1-17

Parking Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-15

Rear Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-19

Rocker Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-14

Stabilizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-18

Tank Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-8, 91-1-9

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Inside Back Cover

NOTES:

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-1

MARCH, 2011

CAB CONTROL MOUNT

REF. PART

NO. NO.

DESCRIPTION QTY.

1 42491.01 Mount Plate 1
2 9100104 Flatwasher 8mm 2
3 9100204 Lockwasher 8mm 2
4 9193004 Wing Nut 2
5 9313054 Capscrew M8 x 25 2

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-2

MARCH, 2011

CONTROL VALVE ASSEMBLY

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-3

MARCH, 2011

CONTROL VALVE ASSEMBLY

REF. PART

NO. NO.

DESCRIPTION QTY.

1 8130616 VALVE 3 SPOOL 1
2 8650103 BONDED SEAL 3/8" BSP 8
3 08.955.06 ADAPTER 3/8" BSP X 9/16" JIC 5
4 8581222 ADAPTER 3/8" BSP X 7/8" JIC 1
5 8581170 ADAPTER 3/8" BSP X 3/4" JIC 1
6 8125343 VALVE SD11 ROTOR CONTROL 1
7 8650104 BONDED SEAL 1/2" BSP 3
8 41328.01 VALVE MTG BRKT 1

9 05.835.11 SWIVEL ELBOW 1/4" BSP F X 9/16" JIC M 1
10 8581115 ADAPTER 3/8" X 1/4" BSP MM 1
11 8581254 ADAPTER TEE 1/4" BSP F-M-M 1
12 8581341 ADAPTER 1/4 BSP F X 9/16" JIC M 1
13 8650102 SEAL 1/4" BSP 1
14 8650106 SEAL 3/4" BSP 2
15 8017054 CONTROL HEAD & CABLE 2.0M 3
16 8017045 CONTROL HEAD & CABLE 2.5M 1
17 8581226 ADAPTER 1/2" BSPX 7/8"JIC MM 3
18 8581271 ADAPTER 3/4" BSP X 7/8" JIC MM 2
19 9343022 CAPSCREW M5 X 12 8
20 09.970.02 BRACKET - 4 LEVER MTG RH - 3MM PLT 1
21 04.282.70 STUD M6 X 191 3
22 9143003 SELF-LOCKING NUT M6 6
23 9313034 CAPSCREW M8 X 16 2
24 9193004 WING NUT M8 2
25 1290368 DECAL - CABLE, REACH - ANGLE-LIFT 1
26 1290338 DECAL - ROTOR CONTROL VALVE 1
27 9213164 CAPSCREW M8 X 80 3
28 9313044 CAPSCREW M8 X 20 2
29 9143004 SELF-LOCKING NUT M8 5

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-4

MARCH, 2011

HYDRAULIC HOSES

REF. PART
NO. NO.

DESCRIPTION QTY.

1 41675.22 7/8" JIC HOSE FS/F90 1200LG 1
2 41674.55 7/8" JIC HOSE FS/FS 4500LG 2
3 41674.14 7/8" JIC HOSE 700 LG FS/FS 1
4 41671.12 7/8" HOSE FS/F90 600LG 1/2 BORE 1
5 08.958.24 3/4" JIC FS/F90 1400 LG HOSE 1
6 08.957.24 1/4” x 59 HOSE,(1/4FJX x 1/4FJX90) 2
7 41721.45 9/16" JIC HOSE FS/FS 3
8 08.957.22 9/16" HOSE FS/F90 1200LG 1
9 08.957.21 9/16" JIC HOSE FS/F9 1

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-5

MARCH, 2011

HYDRAULIC FITTINGS

REF. PART
NO. NO.

DESCRIPTION QTY.

1 41014.14 LIFT RAM ASSY JIC PA41 1

2 41014.15 REACH RAM ASSYJIC PA41 1
3 7442258 ANGLING RAM ASSY JIC 1
4 7198293 BREAK AWAY RAM ASSY JIC 1
5 06.430.09 CLAMP PLATE 4
6 06.418.03 CLAMP PLATE 4
7 9213114 CAPSCREW M8 X 55 (COARSE) 4
8 70093C LOCKNUT M8 X 1.25 TOP LOCK 4

9 8501273 1-1/4" BORE SAE RUB HOSE 1
10 0904107 HOSE CLIPS 40-55 MM *BI* 4
11 05.835.11 ADAPTOR,SWIV 90-1/4 X 9/16” JIC 1
12 8650102 SEAL,1/4” BSP BONDED 3
13 8582054 1/2" BSP BLANKING CAP 2
14 00900913 SLEEVING 2.54” ID BLACK 1020
15 8581226 HYD ADP ST 1/2” BSP-MX7/8 JIC-M 3

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-6

MARCH, 2011

GEARBOX AND PUMP ASSEMBLY

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-7

MARCH, 2011

GEARBOX AND PUMP ASSEMBLY

REF. PART
NO. NO.

DESCRIPTION QTY.

1 8013443 GEARBOX 1:2.6 RATIO 1
2 8201466 PUMP,TANDEM 1
3 8013082 CONNECTION,SUCTION 1
4 8013023 GASKET,INLET 1
5 9213144 CAPSCREW M8 X 70 2
6 9213095 CAPSCREW 10-P1.5 - 45MM PL5 4
7 9100204 LOCKWASHER 8MM 2
8 9100205 LOCKWASHER 10MM DIA. BZP 4

9 8002059 RETURN CONNECTION 1
10 8650104 SEAL 1/2" BONDED PP45D 3
11 8650106 SEAL,3/4" BSP BONDED 1
12 8600119 O-RING 1" ID X1-1/4" OD 1
13 9300147 CAPSCREW SOCKET M8 X 20 4
14 1290030 DECAL, (BERVIN) 1
15 8501099 HOSE, 5/8" BORE 13" LONG 1
16 8581173 ELBOW CONNECTION, 5/8” BSP 1
17 G3812120 5/8" BSP - 1/2" BSP M-M 1
18 0904204 HOSE CLIP, 5/8” DIA. BORE 2
19 42415.02 SPACER DIA 30 x 28 1
20 8013097 SPLINED ADAPTOR COUPLING 1
21 18120003 ADP HYD ST 3/4”JIC-MX1/2BSP-M 1
22 8013088 FLANGE, 3/4” BSP 1
23 8581167 UNION, 1-1/16”- 3/4” BSP 1

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-6

MARCH, 2011

TANK ASSEMBLY

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-9

MARCH, 2011

TANK ASSEMBLY

REF. PART

NO. NO.

DESCRIPTION QTY.

1 41196.06 TANK W/ASSY-RH PA90 & PA41 1
2 41204.01 TANK STRAP - PA90 1
3 8401045 FILTER 1
4 8581226 ADP HYD ST 1/2" BSP-MX7/8JIC-M 1
5 8650103 SEAL, 3/8" BSP BONDED 3
6 8650104 SEAL, 1/2" BSP BONDED 2
7 9313065 CAPSCREW M10X1.5 - 30MM PL5 4
8 765676 LOCKNUT, TOP LOCK M10 X 1.5P 4

9 70093C LOCKNUT, TOPLOCK M8 X 1.25 2
10 8581174 UNION, 1/2'' BSP 1 UNF M/M 1
11 8003001 3/8" BSP PLUG 3
12 8581203 PLUG 1 TAPER 1
13 8401050 ASSY, FILLER BREATHER 1
14 8582042 1/4" GAS PIPE PLUG TAPER 1
15 9213144 CAPSCREW M8 X 70 (COARSE) 2

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-10

MARCH, 2011

DIPPER - LOWER, RH

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-11

MARCH, 2011

DIPPER - LOWER, RH

REF. PART
NO. NO.

DESCRIPTION QTY.

1 41202.02 RH OUTER DIPPER ARM 1
2 7191041 PIN, ANGLE RAM BASE 1
3 41206.01 RADIUS ARM W/ ASSY 2
4 41207.02 SLAVE LINK RH W/ASSY 1
5 41270.01 PIN 2
6 21149.01 PIVOT, BUSH 27
7 214060 BUSHING 1-1/4” OD X 1” IDX 1/16LG 6
8 1090001 BEARING,HINGE 2

9 9313065 HEXB METRIC 10-P1.5 - 30MM PL 51
10 9313055 HEXB METRIC 10-P1.50- 25MM 1
11 00765676 LOCKNUT M10-1.5P TOP LOCK 62
12 0425540 ROLL PIN M5 X 40 3
13 0901121 GREASE NIPPLE,1/8’’ BSP-STRAIGHT 5
14 7490813 BRACKET KIT RH 1
15 41261.44 BLANKING PLATE 1
16 9313086 CAPSCREW M12-P 1.75 - 40MM 52
17 9143006 NUT METRIC 12MM-P1.75 PL 2

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-12

MARCH, 2011

DIPPER - UPPER, RH

REF. PART
NO. NO.

DESCRIPTION QTY.

1 41201.04 DIPPER UPPER W/A RH-HBM400 1
2 21149.01 PIVOT, BUSHING 2
3 0901121 GREASE NIPPLE,1/8" BSP-STRAIGHT 1
4 41267.05 PIN - 1" DIA X 102MM LONG 1
5 9313055 CAPSCREW M10-P1.50- 25MM 1
6 00765676 LOCKNUT, M10 P1.5 TOP LOCK 2
7 41269.01 PIN-BREAK AWAY 1
8 9313075 CAPSCREW M10-P1.50- 35MM 1

9 7191036 PIN,BREAKAWAY RAM BASE 1
10 0431105 PIN, COTTER 1
11 43158.01 HOSE SUPPORT HOOP 1
12 9313044 SETSCREW M8-P1.25-20MM GR. 8.8 2
13 9100204 SPRING WASHER 8MM 2

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-13

MARCH, 2011

MAINARM

REF. PART
NO. NO.

DESCRIPTION QTY.

1 41199.06 MAINARM W/ASSY RH 1
2 21149.01 PIVOT, BUSHING 2
3 0901121 GREASE NIPPLE, 1/8" BSP-STRAIGHT 3
4 41200.02 TENSION LINK 1
5 7105050 BUSHING, ROD END 1-1/4” OD X 1“ ID 2
6 41268.02 MAIN PIVOT PIN 1
7 9313045 CAPSCREW M10-P1.5 - 20MM 1
8 00765676 LOCKNUT, M10-P1.5 TOP LOCK 1
9 41691.04 PIN W / ASSY. - LIFT / REACH-MAG420 1

10 9313065 CAPSCREW 10-P1.5 - 30MM PL5 1

11 43021.05 TRANSPORT PROP W/ASSY 1
12 43114.01 PROP PIN W / ASSY-PA410 1
13 43115.01 LOCK PIN-PROP 1
14 9501326 SPLIT PIN M5 DIA NOM X 32 LG 1
15 0431105 PIN, COTTER 1
16 9100205 LOCKWASHER- 10MM DIA. BZP 1

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-14

MARCH, 2011

ROCKER ASSEMBLY

REF. PART

NO. NO.

DESCRIPTION QTY.

1 41861.02 ROCKER W/ASSY-PA41 1
2 41268.02 MAIN PIVOT PIN W/A 2
3 41691.02 PIN - ANGLE BASE 3
4 9313075 CAPSCREW M10-P1.50- 35MM 2
5 9313065 CAPSCREW M10-P1.5 - 30MM PL5 3
6 00765676 LOCKNUT M10-P1.5 TOPLOCK 5

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-15

MARCH, 2011

PARKING STAND

REF. PART

NO. NO.

DESCRIPTION QTY.

1 41939.04 LIFT FRAME 1
2 7550030 DIPPER LOCKING STRAP-PA2050M 1
3 9213166 CAPSCREW M12 X 80 (COARSE) 1
4 9213086 CAPSCREW M12 X 40 (COARSE) 1
5 9313075 CAPSCREW M10-P1.50- 35MM 2
6 00765676 LOCKNUT M10 - P1.5 TOPLOCK 2
7 9143006 NUT 12MM-P1.75 PL 2

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-16

MARCH, 2011

MAINFRAME

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-17

MARCH, 2011

MAINFRAME

REF. PART

NO. NO.

DESCRIPTION QTY.

1 41197.06 MAINFRAME 1
2 21149.01 PIVOT, BUSHING 1-1/2” X 1-1/4” X1-11/16” 2
3 0901121 GREASE NIPPLE, 1/8" STRAIGHT 1
4 0431217 LINCH PIN, MED. 7/16” 2
5 7114289 DRIVELINE S-40 1-3/8"-6 X 1-3/8"- 6 1
6 41203.02 STAND LEG 2
7 43020.02 LEG PIN 2
8 0431105 PIN, COTTER 2

9 1090043 PIN 2
10 9501326 SPLIT PIN M5 DIA X 32 LG 2
11 9313046 CAPSCREW M12 X 20 (COARSE) H.T. 1
12 9100206 LOCKWASHER 12MM 4
13 41267.02 PIN 1
14 00765676 LOCKNUT M10 -P1.5 TOPLOCK 1
15 9313065 CAPSCREW M10-P1.5 - 30MM PL5 1
16 21855.01 PTO GUARD 1
17 9313056 CAPSCREW M12-P1.75- 25MM PL5 3

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-18

MARCH, 2011

STABILIZER

REF. PART

NO. NO.

DESCRIPTION QTY.

1 41205.02 STABILIZER 1
2 9313118 CAPSCREW M20 X 55 (COARSE) H.T. 2
3 9113008 NUT METRIC 20MM-P2.5 4
4 9100208 LOCKWASHER 20MM 2
5 7192026 PIN, TOP LINK 2
6 0431105 PIN, COTTER 2
7 1467063 SLEEVE 2
8 7499506C STABILIZER TONGUE CAT.3-CAST 1

9 9213228 BOLT 2
10 21160.03 PTO HOOK SUPPORT-PLATED 1
11 21883.01 SLEEVE HFS TUBE 38.6 X 6.3 WAL 1
12 7196045 HOSE TIE- 350.0LG 1

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-19

MARCH, 2011

REAR COVER

REF. PART

NO. NO.

DESCRIPTION QTY.

1 45629.02 REAR COVER MOLDING RH 1
2 45633.02 TANK COVER W/A-RH 1
3 45636.03 SUPPORT BRACKET-RH 1
4 45638.01 TANK FAIRING 1
5 43449.02 OVERCENTRE FASTENER 2
6 1069088 POP RIVER-4.5 DIA X 10 LG 6
7 9313055 CAPSCREW M10-P1.5 - 25MM 2
8 9313045 CAPSCREW M10-P1.5 - 20MM 2
9 9100025 M10 COARSE DOMED NUT PLATED 4

10 9100105 FLATWASHER,10.5 X 23.5 X 2.0 8

11 9100205 LOCKWASHER- 10MM DIA. 6
12 00765676 LOCKNUT M10 -P1.5 2
13 46007.01 HOOK-SMALL 1

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-20

MARCH, 2011

FLAIL HEAD

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-21

MARCH, 2011

FLAIL HEAD

REF. PART

NO. NO.

DESCRIPTION QTY.

1 41282.12 CASING-1.0M RH IB/LH OB SLID 1
2 42495.01 MOTOR COVER 1
3 42496.01 WELDMT, BEARING COVER 1
4 7442250 FRONT HOOD KIT 1
5 7442254 FRONT FLAP KIT 1
6 41285.03 ROLLER BRKT LH 1
7 41285.04 ROLLER BRKT RH 1
8 41301.02 ROLLER ASSY 1.0M - MAG420 1

9 41290.02 REAR FLAP CLAMP STRIP 1
10 41289.02 REAR FLAP 1
11 9143006 LOCKNUT M12 X P1.75 PL 18
12 70093C LOCKNUT M8 X 1.25 TOP LOCK 11
13 9313076 CAPSCREW M12-P1.75- 35MM 8
14 9313066 CAPSCREW M12-P1.75- 30MM 2
15 9313056 CAPSCREW M12-P1.75- 25MM 3
16 9313034 CAPSCREW M8-P1.25- 16MM 9
17 9313086 CAPSCREW M12-P1.75- 40MM 52
18 9100208 LOCKWASHER 20MM 2
20 9113008 NUT METRIC 20MM-P2.5 4
21 41284.02 ROTOR ASSY. 1.0M 1
22 7190463 FLAIL- 40MM (140 DIA. ROTOR) 28
23 05.895.01 SHACKLE 28
24 41.167.02 BOLT PACK (10 BOLTS, WSHRS, NUTS) 3
26 02.807.01 SPACER 1 O.D. X 16MM X 27MM 28
27 701515C M16 FLATWASHER 56
28 42503.01 WASHER,SPECIAL 1
29 9353076 SHCS METRIC 12 x 35 1
30 42603.02 MOTOR MTG ASSY PA90 1
31 03.008.01 BEARING ASSY FLANGED 40 BORE 1
32 9213126 HEX HD BOLT M12 X 60 (COARSE)H.T 3
33 9213284 M8 X 40 (COARSE) H.T. HEX 1
34 9213204 CAPSCREW M8-P1.25-100MM PL5 1
35 03.871.01 BUSHING RUBBER 3
36 02.824.01 WASHER 50 O/D X 13 I/D X 5MM 3
37 05.968.02 NUT M10 S/L FINE 4
38 41297.02 HOSE BRKT-JIC 1
39 41674.23 HIGH PRESURE HOSE 5/8” X 52.5" 2
40 21874.01 CLAMP BAR LONG 1
41 21874.02 CLAMP BAR SHORT 1
42 06.418.03 CLAMP PLATE 1
43 06.430.09 CLAMP PLATE 1
44 8650106 SEAL, 3/4BSP BONDED 2
45 8581271 ADAPTER HYD ST 3/4” MBSP-7/8MJIC 2
46 21978.09 HEAD DECAL KIT BUSH HOG 1

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-22

MARCH, 2011

CUTTERBAR - SHEARTRIM

REF. PART

NO. NO.

DESCRIPTION QTY.

1 42018.05 CUTTER BAR RH 1
2 42019.10 CUTTER BAR BRACKET RH 1
3 00765676 LOCKNUT M10-P1.5 TOPLOCK 4
4 9213155 CAPSCREW M10 X 75 4
5 8581226 ADAPTOR HYD ST 1/2" SP-MX7/8" JIC-M 2
6 8650104 SEAL,1/2" BSP BONDED 2
7 41675.22 7/8" JIC HOSE FS/F90 1200LG 2
8 09.821.35 COMBINED EURO DECAL 1

9 3688303 DECAL,DANGER SEVERED FINGERS 1
10 1458392 DECAL,RED REFLECTOR 1
11 1458393 DECAL,YELLOW REFLECTOR 2

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-23

MARCH, 2011

GUARD KIT

REF. PART

NO. NO.

DESCRIPTION QTY.

1 7313049 GUARD PANEL, LARGE SELF COLOR 1
2 7313050 GUARD PANEL, SMALL- SELF COLOR 1
3 6001064 GUARD SPRING 2
4 6001065 GUARD HOOK 6
5 41587.01 GUARD HOOK 6
6 41745.01 HOOK,PLASTIC 8

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-24

MARCH, 2011

DECALS -BUSH HOG MARKING

REF. PART

NO. NO.

DESCRIPTION QTY.

1 50068741 MODEL DECAL, RMB1445 2
2 50063360 DECAL, BH 8" 1
3 50061049 BUSH HOG DECAL 1
4 83380 SMV DECAL 1

BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL

91-1-25

MARCH, 2011

LIFT FLOAT KIT

REF. PART

NO. NO.

DESCRIPTION QTY.

1 8126042 ACCUMULATOR 1.0L 1
2 G2410380 ADAPTOR 3/8" BSP X M22 M-M 1
3 8130183 POPPET VALVE NC 1
4 8126287 VALVE BLOCK-LIFT FLOAT 1
5 8126037 PISTON, RESPONSE 1
6 8116011 SPRING .275X23 SWG X 5/8 " LG 1
7 08.955.06 ADAPTOR 2
8 8650103 SEAL, 3/8" BSP BONDED 3

9 8650322 SEAL M22 BONDED 1
10 8126286 ACCUMULATOR BRACKET 1
11 9313054 CAPSCREW M8-P1.25- 25MM 2
12 9100104 WASHER, PLAIN 8MM DIA. BZP 2
13 70093C LOCKNUT M8 X 1.25P TOP LOCK 2
14 08.957.09 HOSE 1/4" BORE X 9/16" JIC 1
15 1290061 OPERATION DECAL 1
16 8402194 SWITCH KIT-LIFT FLOAT 1
17 7192081 SWITCH BRACKET 1

2501 Griffin Ave.• Selma, AL 36703

[phone] • [phone]

Parts Ordering 1 800 304 2836

Fax [phone]

www.bushhog.com