Bush Hog RMB1445 User Manual
RMB1445
RMB1445-1
BOOM MOWER
HYDRAULIC BOOM CUTTER
Published 10/12
PART'S MANUAL
SECTION 91
Important Operating
and Safety Instructions
are found in the Mower
Safety Video that can
be instantly accessed
on the internet at:
www.algqr.com/bve
An Operator’s Manual was shipped with the
equipment. The Operator’s Manual is an integral
part of the safe operation of this machine and
must be maintained with the unit at all times.
READ, UNDERSTAND, and FOLLOW the
Safety and Operation Instructions contained in
this manual before operating the equipment. If
the Operator’s Manual is not with the equipment,
contact your dealer or Bush Hog to obtain a copy
before operating the equipment.
©2009 Alamo Group Inc.
PARTS ORDERING GUIDE
The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section.
1. The Parts Section is prepared in logical sequence and grouping of parts that belong
to the basic machine featured in this manual. Part Numbers and Descriptions are given
to help locate the parts and quantities required.
2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the
machine for which the parts are ordered.
3. The Purchase Order must clearly list the quantity of each part, the complete and correct
part number (be sure to include all periods), and the basic name of the part.
4. The Manufacturer reserves the right to substitute parts where applicable.
5. Some parts are unlisted items which are special production items not normally stocked
and are subject to special handling. Request a quotation for such parts before sending
a Purchase Order.
6. The Manufacturer reserves the right to change prices without prior notice.
For maximum safety and to guarantee optimum product reliability, always
use genuine BUSH HOG Parts. The use of inferior replacement parts may
causepremature or catastrophic failure which could result in serious injury
or death.Direct any questions regarding parts to:
BUSH HOG
2501 Griffin Ave.
Selma, AL 36703
www.bushhog.com
Contact Us
800-304-2836
To the Owner/Operator/Dealer
All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded
operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has
designed this implement to be used with all its safety equipment properly attached to minimize the chance of
accidents.
BEFORE YOU STAR T! Read the safety messages on the impl ement and shown in your manual. Observe the rules
of safety and common sense!
WARRANTY INFORMATION:
Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty RegistrationForm in
full and return it to within 30 Days. Make certain the Serial Number of the Machine is recorded on theWa rranty Card and
on the Warranty Form that you retain.
LIMITED WARRANTY
2222222222222222222222222222222
Bush Hog warrants to the original purchaser of any new Bu sh Hog equipme nt, purchas ed from a n authorized Bu sh
Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for
non-commercial, state and municipalities’ use and ninety (90) days for commercial use from date of retail sale. The
obligation of Bush Hog to the purchaser under this warranty is limited to the repair or replacement of defective
parts.
Replacement or repair parts installed in the equipment covered by this limited warranty are warranted for ninety
(90) days from the date of purchase of such part or to the expiration of the applicable new equipment warranty
period, whichever occurs later . Warranted parts shall be provided at no cost to the user at an authorized Bush Hog
dealer during regular working hours. Bush Hog reserves the right to inspect any equipment or parts which are
claimed to have been defective in material or workmanship.
DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES
Bush Hog’s obligation under this limited warranty, to the extent allowed by law, is in lieu of all warranties, implied or
expressed, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE and any liability for incidental and consequential damages with respect to the sale or
use of the items warranted. Such incidental and consequential damages shall include but not be limited to:
transportation charges other than normal freight charges; cost of installation other than cost approved by Bush
Hog; duty; taxes; charges for normal service or adjustment; loss of crops or any other loss of income; rental of
substitute equipment, expenses due to loss, damage, detention or delay in the delivery of equipment or parts
resulting from acts beyond the control of Bush Hog.
THIS LIMITED WARRANTY SHALL NOT APPLY:
1. To vendor items which carry their own warranties, such as engines, tires, and tubes.
2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident.
3. If parts not made or supplied by Bush Hog h ave been us ed in connection with the unit, if, in the sole judgement
of Bush Hog such use affects its performance, stability or reliability.
4. If the unit has been altered or repaired outs ide of an autho rized Bush Hog dealership in a manner which , in the
sole judgement of Bush Hog, affects its performance, stability or reliability.
5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic fluid, worn
blades, or to normal deterioration of such things as belts and exterior finish due to use or exposure.
6. To expendable or wear items such as teeth, chains, sprockets, belts, springs and any other items that in the
company’s sole judgement is a wear item.
NO EMPLOYEE OR REPRESENTATIVE OF BUSH HOG IS AUTHORIZED TO CHANGE THIS LIMITED
WARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE IN
WRITING AND SIGNED BY BUSH HOG’S SERVICE MANAGER, 2501 GRIFFIN AVE., SELMA, ALABAMA
36703.
2222222222222222222222222222222
Record the model number, serial number and date
purchased. This information will be helpful to your
dealer if parts or service are required.
MAKE CERTAIN THE WARRANTY
HAS BEEN FILED WITH BUSH HOG
SELMA, ALABAMA
MODEL NUMBER ________________________________
SERIAL NUMBER ________________________________
DATE OF RETAIL SALE ___________________________
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
OCTOBER, 2012
ALPHABETICAL INDEX
RMB1445 BOOM MOWER
ITEM PAGE NUMBER
Adaptor Kit for Control Valve w/ Quick Release . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-5
Cab Control Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-1
Control Valve Assy for RMB1445. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-2, 91-1-3
Control Valve Assy for RMB1445-1 . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-4 and 91-1-6
Cutterbar - Sheartrim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-31
Decals - Bush Hog Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-33
Dipper - Lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-12, 91-1-13
Dipper - Upper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-14
Flail Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-22
Flail Head Motor Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-23
Flail Head Front Flap Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-24
Flail Head Rotor Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-25
Flail Head Roller Module Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-26
Flail Head Casing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-27
Flial Head Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-28
Flail Head Decal Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-29
Flail Head Front Hood Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-30
Gearbox and Pump Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-8, 91-1-9
Guard Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-32
Hydraulic Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-10
Hydraulic Hoses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-7
Lift Float Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-34
Mainframe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-15
Mainframe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-16, 91-1-19
Parking Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-17
Rear Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-21
Rocker Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-16
Stabilizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-20
Tank Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91-1-11
NOTES:
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
91-1-1
OCTOBER, 2012
CAB CONTROL MOUNT
REF. PART
NO. NO.
DESCRIPTION QTY.
1 42491.01 Mount Plate 1
2 9100104 Flatwasher 8mm 2
3 9100204 Lockwasher 8mm 2
4 9193004 Wing Nut 2
5 9313054 Capscrew M8 x 25 2
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
91-1-2
OCTOBER, 2012
CONTROL VALVE ASSEMBLY W/ NON QUICK RELEASE CABLE
Used on Models RMB1445
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
91-1-3
OCTOBER, 2012
CONTROL VALVE ASSEMBLY W/ NON QUICK RELEASE CABLE
Used on Models RMB1445
REF. PART
NO. NO.
DESCRIPTION QTY.
1 8130616 VALVE 3 SPOOL 1
2 8650103 BONDED SEAL 3/8" BSP 8
3 08.955.06 ADAPTER 3/8" BSP X 9/16" JIC 5
4 8581222 ADAPTER 3/8" BSP X 7/8" JIC 1
5 8581170 ADAPTER 3/8" BSP X 3/4" JIC 1
6 8125343 VALVE SD11 ROTOR CONTROL 1
7 8650104 BONDED SEAL 1/2" BSP 3
8 41328.01 VALVE MTG BRKT 1
9 05.835.11 SWIVEL ELBOW 1/4" BSP F X 9/16" JIC M 1
10 8581115 ADAPTER 3/8" X 1/4" BSP MM 1
11 8581254 ADAPTER TEE 1/4" BSP F-M-M 1
12 8581341 ADAPTER 1/4 BSP F X 9/16" JIC M 1
13 8650102 SEAL 1/4" BSP 1
14 8650106 SEAL 3/4" BSP 2
15 8017054 CONTROL HEAD & CABLE 2.0M 3
16 8017045 CONTROL HEAD & CABLE 2.5M 1
17 8581226 ADAPTER 1/2" BSPX 7/8"JIC MM 3
18 8581271 ADAPTER 3/4" BSP X 7/8" JIC MM 2
19 9343022 CAPSCREW M5 X 12 8
20 09.970.02 BRACKET - 4 LEVER MTG RH - 3MM PLT 1
21 04.282.70 STUD M6 X 191 3
22 9143003 SELF-LOCKING NUT M6 6
23 9313034 CAPSCREW M8 X 16 2
24 9193004 WING NUT M8 2
25 1290368 DECAL - CABLE, REACH - ANGLE-LIFT 1
26 1290338 DECAL - ROTOR CONTROL VALVE 1
27 9213164 CAPSCREW M8 X 80 3
28 9313044 CAPSCREW M8 X 20 2
29 9143004 SELF-LOCKING NUT M8 5
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
91-1-4
OCTOBER, 2012
CONTROL VALVE ASSEMBLY W/ QUICK RELEASE CABLE
Used on Models RMB1445-1
10
15
7
2
891 1191312
6
3
4
5
LIFT
ANGLE
REACH
POSITION FOR RCV CABLE
LIFT
REACH
ANGLE
14
Ref. Part Description Qty.
No. No. Req’d.
7434681 CABLE ACV ASSY C/W A.F JIC QR
1 8130616 VALVE 3 SPOOL 160 BAR 1
2 9163003 NYLOC NUT M6 6
3 1290368 DECAL - CABLE, REACH-ANGLE-LIFT 1
4 9343022 CAPSCREW M5x12 6
5 09.970.02 BRKT -4LVR MTG RH - 3MM PLT 1
6 1290338 DECAL - ROTOR CONTROL VALVE 1
7 04.282.70 STUD M6X191 3
8 9213134 BOLT M8x653 9
9 163004 NYLOC NUT M8 5
10 22524.92 ADAPTOR KIT PA3430 / PA4330 CABLE JIC 1
11 41196.58 CABLE VALVE MTG PLATE RH 1
12 9313044 SETSCREW M8x20 2
13 9100104 FLAT WASHER M8 2
14 8017090 QUICK RELEASE HEAD - ARMHEAD 0.4m 3
15 8017093 QUICK RELEASE CABLE ACV 3.1m 3
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
91-1-5
OCTOBER, 2012
ADAPTOR KIT FOR
CONTROL VALVE ASSEMBLY W/ QUICK RELEASE CABLE
Used on Models RMB1445-1
2
2
2
2
RETURN TO RCV
ANGLE
BASE
REACH
BASE
LIFT GLAND
PRESSURE
LIFT BASE
REACH GLAND
ANGLE GLAND
3
3
32
32
4
7
8
6
51
71 952
2
B.AWAY
Ref. Part Description Qty.
No. No. Req’d.
22524.92 ADAPTOR KIT 1
1 8650102 BONDED SEAL 1/4"BSP 2
2 8650103 BONDED SEAL 1/4"BSP 8
3 08.955.06 ADAPTOR 3/8"BSPx9/16JIC 4
4 8581222 ADAPTER 3/8"BSPX7/8"JIC 1
5 8123097 RESTRICTOR UNION 3/8" BSP x 7/8” JIC 2
6 05.835.11 1/4"BSP F X 9/16"JIC M SWIVEL ELBOW 1
7 8581341 ADAPTOR 1/4" BSP F X 9/16"JIC M 2
8 8581170 3/8"BSP x 3/4"JIC ADAPTOR 1
9 8581254 ADAPTOR TEE 1/4" BSP MFM 1
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
91-1-6
OCTOBER, 2012
CONTROL VALVE ASSEMBLY W/ QUICK RELEASE CABLE
Used on Models RMB1445-1
Ref. Part Description Qty.
No. No. Req’d.
7434682 CABLE RCV ASSY JIC QR 3.5M 1
1 23007.01 CABLE VALVE MTG PLATE RH 1
2 8125343 ROTOR CONTROL VALVE SD11 1
3 8650104 BONDED SEAL 1/2"BSP" 3
4 8650106 BONDED SEAL 3/4"BSP 2
5 8581226 ADAPTOR 1/2"BSP x 7/8"JIC MM 3
6 8581271 3/4"BSP-7/8"JIC MM ADAPTOR 2
7 9100104 FLAT WASHER M8 2
8 9163004 NYLOC NUT M8 5
9 9213144 BOLT M8x70 3
10 9313064 SETSCREW M8x30 2
11 9343022 CAPSCREW M5x12 2
12 41196.90 PACKER 1
13 8017089 QUICK RELEASE HEAD - ROTOR 1
14 8017091 QUICK RELEASE CABLE RCV 3.1m 1
14 8 9
6
6
5
2
11 4
4
3
1087
1
12
13
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
91-1-7
OCTOBER, 2012
HYDRAULIC HOSES
REF. PART
NO. NO.
DESCRIPTION QTY.
1 41675.22 7/8" JIC HOSE FS/F90 1200LG 1
2 41674.55 7/8" JIC HOSE FS/FS 4500LG 2
3 41674.14 7/8" JIC HOSE 700 LG FS/FS 1
4 41671.12 7/8" HOSE FS/F90 600LG 1/2 BORE 1
5 08.958.24 3/4" JIC FS/F90 1400 LG HOSE 1
6 08.957.24 1/4” x 59 HOSE,(1/4FJX x 1/4FJX90) 2
7 41721.45 9/16" JIC HOSE FS/FS 3
8 08.957.22 9/16" HOSE FS/F90 1200LG 1
9 08.957.21 9/16" JIC HOSE FS/F9 1
Loading...