BUSH HOG
MP5/MP6
®
MULCH PRO
Operator’s Manual
ASSEMBLY ● OPERATION ● MAINTENANCE
798 $4.00
50018726
CONGRATULATIONS!
You have invested in the best implement of its type on the market today.
The care you give your Bush Hog implement will greatly determine your satisfaction
with its performance and its service life. We urge a careful study of this manual to provide
you with a thorough understanding of your new implement before operating, as well as
suggestions for operation and maintenance.
If your manual should become lost or destroyed, Bush Hog will be glad to provide you with
a new copy. Order from Bush Hog, P. O. Box 1039, Selma, Alabama 36702-1039.
As an authorized Bush Hog dealer, we stock genuine Bush Hog parts which are
manufactured with the same precision and skill as our original equipment. Our trained
service personnel are well informed on methods required to service Bush Hog equipment,
and are ready and able to help you.
Should you require additional information or assistance, please contact us.
YOUR AUTHORIZED
BUSH HOG DEALER
BECAUSE BUSH HOG MAINTAINS AN ONGOING
PROGRAM OF PRODUCT IMPROVEMENT, WE
RESERVE THE RIGHT TO MAKE IMPROVEMENTS IN
DESIGN OR CHANGES IN SPECIFICATIONS WITHOUT INCURRING ANY OBLIGATION TO INSTALL
THEM ON UNITS PREVIOUSLY SOLD.
BECAUSE OF THE POSSIBILITY THAT SOME
PHOTOGRAPHS IN THIS MANUAL WERE TAKEN OF
PROTOTYPE MODELS, PRODUCTION MODELS MAY
VARY IN SOME DETAIL. IN ADDITION, SOME
PHOTOGRAPHS MAY SHOW SHIELDS REMOVED
FOR PURPOSES OF CLARITY. NEVER OPERATE
THIS IMPLEMENT WITHOUT ALL SHIELDS IN PLACE.
1
MP5/6
Operator’s Manual
TABLE OF CONTENTS
SECTION/PARA PAGE
Warranty....................................................3
Dealer Preparation Check List ..................4
Safety Precautions....................................5
Federal Laws and Regulations..................6
I INTRODUCTION AND DESCRIPTION......7
1-1 Introduction ..........................................7
1-2 Description...........................................7
II PREPARATION FOR USE .........................8
2-1 Attaching to Tractor ..............................8
III OPERATING INSTRUCTIONS.................10
3-1 General Safety...................................10
3-2 Cutting Height Adjustment .................10
3-3 Operation ...........................................10
3-4 Transporting.......................................10
Tips On Mulching ................................... 11
SECTION/PARA PAGE
IV MAINTENANCE.......................................12
4-1 Maintenance Check List.....................12
4-2 Lubrication..........................................12
4-3 Belt Adjustment..................................13
4-4 Belt Replacement...............................13
4-5 Blade Replacement............................14
4-6 Blade Spindle Service........................15
4-7 Troubleshooting..................................16
V DEALER ASSEMBLY...............................17
5-1 Base Unit Assembly...........................17
Safety Decals...........................................19
Torque Specifications ...............................20
RETAIL CUSTOMER’S RESPONSIBILITY
UNDER THE BUSH HOG WARRANTY
It is the Retail Customer and/or Operator’s responsibility to read the Operator’s
Manual, to operate, lubricate, maintain and store the product in accordance with all
instructions and safety procedures. Failure of the operator to read the Operator’s
Manual is a misuse of this equipment.
It is the Retail Customer and/or Operator’s responsibility to inspect the product and to
have any part(s) repaired or replaced when continued operation would cause damage
or excessive wear to other parts or cause a safety hazard.
It is the Retail Customer’s responsibility to deliver the product to the authorized Bush
Hog Dealer, from whom he purchased it, for service or replacement of defective parts
which are covered by warranty. Repairs to be submitted for warranty consideration
must be made within forty-five (45) days of failure.
It is the Retail Customer’s responsibility for any cost incurred by the Dealer for traveling to or hauling of the product for the purpose of performing a warranty obligation or
inspection.
2
®
BUSH HOG
LIMITED WARRANTY
✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯
Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an
authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period
of one (1) year for non-commercial, state, and municipalities’ use and ninety (90) days for commercial use from
date of retail sale. The obligation of Bush Hog to the purchaser under this warranty is limited to the repair or
replacement of defective parts.
Replacement or repair parts installed in the equipment covered by this limited warranty are warranted
for ninety (90) days from the date of purchase of such part or to the expiration of the applicable new equipment warranty period, whichever occurs later. Warranted parts shall be provided at no cost to the user at an
authorized Bush Hog dealer during regular working hours. Bush Hog reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship.
DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES
Bush Hog’s obligation under this limited warranty, to the extent allowed by law, is in lieu of all war-
ranties, implied or expressed, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE and any liability for incidental and consequential damages with respect to
the sale or use of the items warranted. Such incidental and consequential damages shall include but not be
limited to: transportation charges other than normal freight charges; cost of installation other than cost
approved by Bush Hog; duty; taxes; charges for normal service or adjustment; loss of crops or any other loss of
income; rental of substitute equipment, expenses due to loss, damage, detention or delay in the delivery of
equipment or parts resulting from acts beyond the control of Bush Hog.
THIS LIMITED WARRANTY SHALL NOT APPLY:
1. To vendor items which carry their own warranties, such as engines, tires, and tubes.
2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident.
3. If parts not made or supplied by Bush Hog have been used in connection with the unit, if, in the sole judgement of Bush Hog such use affects its performance, stability or reliability.
4. If the unit has been altered or repaired outside of an authorized Bush Hog dealership in a manner
which, in the sole judgement of Bush Hog, affects its performance, stability or reliability.
5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic fluid,
worn blades, or to normal deterioration of such things as belts and exterior finish due to use or
exposure.
6. To expendable or wear items such as teeth, chains, sprockets, belts, springs and any other items that in the
company’s sole judgement is a wear item.
NO EMPLOYEE OR REPRESENTATIVE OF BUSH HOG IS AUTHORIZED TO CHANGE THIS LIMITED WARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE
IN WRITING AND SIGNED BY BUSH HOG’S SERVICE MANAGER, POST OFFICE BOX 1039, SELMA,
ALABAMA 36702-1039.
✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯
Record the model number, serial number and date
purchased. This information will be helpful to your
dealer if parts or service are required.
MAKE CERTAIN THE WARRANTY REGISTRATION
CARD HAS BEEN FILED WITH BUSH HOG/
SELMA, ALABAMA
MODEL NUMBER
SERIAL NUMBER
DATE OF RETAIL SALE
3
DEALER PREPARATION CHECK LIST
MP 5/6 Finishing Mowers
BEFORE DELIVERING MACHINE — The following check list should be completed.
Use the Operator’s Manual as a guide.
❒ 1. Assembled completed.
❒ 2. Gearboxes filled with oil.
❒ 3. All fittings lubricated.
❒ 4. All shields in place and in good condition.
❒ 5. All fasteners torqued to specifications given in Torque Chart
❒ 6. All decals in place and readable. (See decal page.)
❒ 7. Overall condition good (i.e. paint, welds)
❒ 8. Operators manual has been delivered to owner and he has been instructed
on the safe and proper use of the cutter.
Dealer’s
Signature
Purchaser’s
Signature
THIS CHECKLIST TO REMAIN IN OWNER’S MANUAL
It is the responsibility of the dealer to complete the procedures listed
above before delivery of this implement to the customer.
4
IMPORTANT SAFETY PRECAUTIONS
This symbol is used to call attention to safety precautions that should be followed by
the operator to avoid accidents. When you
see this symbol, carefully read the message
that follows and heed its advice. Failure to
comply with safety precautions could result
in serious bodily injury.
In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence and proper training of personnel in the operation, transport,
maintenance and storage of equipment. Lack of attention to safety can result in accident, personal injury,
reduction of efficiency and worst of all—loss of life. Watch for safety hazards and correct deficiencies promptly. Use the following safety precautions as a general guide to safe operations when using this machine.
Additional safety precautions are used throughout this manual for specific operating and maintenance procedures. Read this manual and review the safety precautions often until you know the limitations.
1. Read the Operator’s Manual. Failure to read the Operator’s Manual is considered a misuse of this
equipment.
2. Become familiar with all the machine’s controls and all the caution, warning and danger decals affixed
to the machine before attempting to start or operate.
3. Before starting or operating the machine, make a walk around inspection and check for obvious
defects such as loose mounting bolts and damaged components. Correct any deficiency before
starting.
4. Do not allow children to operate the cutter. Do not allow adults to operate it without proper instruction.
5. Do not carry passengers.
6. Keep the area of operation clear of all persons, particularly small children and pets. The operator
should cease mowing whenever anyone comes within the operating area.
7. Clear the work area of objects which might be picked up and thrown.
8. Use a piece of cardboard or wood rather than hands to search for hydraulic leaks. Escaping hydraulic
oil under pressure can penetrate skin. If fluid is injected into the skin, it must be surgically removed
within a few hours by a doctor familiar with this form of injury or gangrene may result.
9. Do not operate without all guards and shields in place and in good condition.
10. Lower implement to ground, stop tractor engine, apply parking brake, and allow blades to completely
stop before leaving the tractor.
11. Keep hands and feet away from blades.
12. This cutter is not to be operated along highways or in any area where people may be present unless
all sides of the unit are enclosed by permanent bands, safety chains or other factory approved safety
shields that are in good repair.
13. Wear personal protective equipment such as, but not limited to, protection for eyes, ears, feet, hands
and head when operating or repairing the equipment. Do not wear loose clothing or jewelry that may
catch on equipment moving parts.
14. When performing adjustments or maintenance on the cutter, first lower it to the ground or block it
securely at a workable height.
15. Never stand between tractor and cutter while tractor is being backed to the cutter hitch.
16. Reduce speed when transporting cutter to avoid bouncing and momentary loss of steering.
17. Use tractor flashing warning lights, day or night, when transporting cutter on road or highways unless
prohibited by law.
18. It is recommended that tractor be equipped with Rollover Protective System (ROPS) and seat belt be
used in all mowing operations.
5
IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING
EMPLOYERS, EMPLOYEES AND OPERATIONS.
*(This section is intended to explain in broad terms the concept and effect of the following federal laws and
regulations. It is not intended as a legal interpretation of the laws and should not be considered as such).
U.S. Public Law 91-596 (The Williams-Steiger Occupational and Health Act of 1970) OSHA
This Act Seeks:
“...to assure so far as possible every working man and woman in the nation safe and healthful working
conditions and to preserve our human resources...”
DUTIES
Sec. 5 (a) Each employer—
(1) shall furnish to each of his employees employment and a place of employment
which are free from recognized hazards that are causing or are likely to cause
death or serious physical harm to his employees;
(2) shall comply with occupational safety and health standards promulgated under
this Act.
(b) Each employee shall comply with occupational safety and health standards
and all rules, regulations and orders issued pursuant to this Act which are
applicable to his own actions and conduct.
OSHA Regulations
Current OSHA regulations state in part: “At the time of initial assignment and at least annually thereafter, the
employer shall instruct every
employee is, or will be involved.” These will include (but are not limited to) instructions to:
employee in the safe operation and servicing of all equipment with which the
Keep all guards in place when the machine is in operation;
Permit no riders on equipment;
Stop engine, disconnect the power source, and wait for all machine movement to stop before
servicing, adjusting, cleaning or unclogging the equipment, except where the machine must be
running to be properly serviced or maintained, in which case the employer shall instruct employees
as to all steps and procedures which are necessary to safely service or maintain the equipment.
Make sure everyone is clear of machinery before starting the engine, engaging power, or operating
the machine.
EMPLOYEE TRACTOR OPERATING INSTRUCTIONS:
1. Securely fasten your seat belt if the tractor has a
ROPS.
2. Where possible, avoid operating the tractor near
ditches, embankments, and holes.
3. Reduce speed when turning, crossing slopes, and
on rough, slick, or muddy surfaces.
4. Stay off slopes too steep for safe operation.
Child Labor Under 16 Years Old
Some regulations specify that no one under the age of 16 may operate power machinery. It is your
responsibility to know what these regulations are in your own area or situation. (Refer to U.S. Dept. of
Labor, Employment Standard Administration, Wage & Home Division, Child Labor Bulletin #102.)
5. Watch where you are going, especially at row
ends, on roads, and around trees.
6. Do not permit others to ride.
7. Operate the tractor smoothly - no jerky turns,
starts, or stops.
8. Hitch only to the drawbar and hitch points recom-
mended by tractor manufacturers.
9. When tractor is stopped, set brakes securely and
use park lock if available.
6
SECTION I
INTRODUCTION AND DESCRIPTION
1-1 INTRODUCTION
We are pleased to have you as a Bush Hog customer. Your MP Series Rotary Cutter has been carefully designed to give maximum service with minimum down time.This manual is provided to give you
the necessary operating and maintenance instructions for keeping your rotary cutter in top operating
condition. Please read this manual thoroughly.
Understand what each control is for and how to use
it. Observe all safety precautions decaled on the
machine and noted throughout the manual for safe
operation of implement. If any assistance or additional information is needed, contact your authorized
Bush Hog dealer.
NOTE
All references made to right, left, top,
bottom, front or rear are as viewed
facing the direction of travel with
implement properly attached to tractor.
1-2 DESCRIPTION
The MP cutters (Figure 1-1) are grooming mowers
intended for cutting lawns, golf courses, athletic
fields, or any maintained area where a clean, uniform finish is desired. Three sets of counter-rotating
blades continue to cut the grass clippings several
times before allowing the tiny pieces to fall to the
ground. This eliminates a build up of grass residue
on top of the lawn. The four caster wheel arrangement, along with the floating lift linkage and the standard front and center rollers, all work together to give
an even cut and minimize scalping.
Power from the tractor is transmitted through a triangular, telescoping driveline to the 90 degree gearbox. It is then passed to the spindle housings and
blades by two, B-section, Kevlar reinforced belts.
Drivetrain protection is provided by belt slippage.
Table 1-1 MTH Specifications
MP 5 MP 6
Cutting Width (in.) 60 72
Cutting Height (in.) 3/4 to 5-3/4
Horsepower Range 20-35 25-40
Blade Tip Speed (fpm) Top 17,600
Bottom 18,500
Weight (lbs.) 680 702
Figure 1-1 MP 5
7
PREPARATION FOR USE
2-1 ATTACHING TO TRACTOR
WARNING
NEVER STAND BETWEEN TRACTOR
AND CUTTER WHILE TRACTOR IS
BEING BACKED TO HITCH.
WARNING
ADDITIONAL TRACTOR FRONT
BALLAST MAY BE NEEDED FOR
STABLE OPERATION AND TRANSPORT
OF CUTTER. SEE TRACTOR OPERATOR’S MANUAL FOR RECOMMENDED
WEIGHTS. IT IS RECOMMENDED THAT
TRACTOR BE EQUIPPED WITH
ROLLOVER PROTECTIVE SYSTEM
(ROPS) AND SEAT BELTS.
A. Attach to tractor Cat. I three point hitch as
described in tractor operator’s manual.
NOTE
Due to the many variations in
tractor/implement hitch points and corresponding differences in distances between
tractor PTO shafts and implement input
shafts, drivelines may need to be shortened as described in the following steps:
SECTION II
D. Hold driveline sections parallel to each other to
determine if too long. Each section should end
approximately 3 inches (76mm) short of reaching
universal joint shield on opposite section. If too
long, measure 3 inches (76mm) back from universal joint shield and mark opposite section. (Figure
2-1). Do this for both sections.
E. Raise and lower cutter to determine position
with greatest distance between PTO shaft and
gearbox input shaft. Shut down tractor leaving cutter in position of greatest distance. SECURELY
BLOCK CUTTER IN POSITION.
F. Hold down driveline sections parallel to each
other and check for minimum 6 inches (152mm)
overlap. (Figure 2-2) If driveline has been marked for
cutting, overlap will be the distance between two
marks. If driveline has less than minimum overlap,
DO NOT USE. Contact authorized Bush Hog dealer.
NOTE
If driveline is correct length, omit the following steps “G” through “J” and proceed
to step “K”.
Figure 2-1
B. Raise and lower cutter to determine position
with shortest distance between the tractor PTO
shaft and gearbox input shaft. Shut down tractor
leaving cutter in position of shortest distance.
SECURELY BLOCK CUTTER IN POSITION.
C. Pull driveline apart. Attach outer (female) section to tractor PTO shaft. Pull on driveline section to
be sure yoke locks into place.
Figure 2-2
Minimum
Overlap
8
G. Clamp end of driveline in a vice. Cut off shield
where marked. (Figure 2-3).
Figure 2-3
H. Using cut off section of shield as a guide, cut
shaft the same amount. (Figure 2-4)
Figure 2-4
Figure 2-5
DANGER
MAKE CERTAIN DRIVELINE YOKES
ARE SECURELY FASTENED. FAILURE
TO DO SO MAY RESULT IN SERIOUS
INJURY.
L. Raise cutter off ground and adjust lower lift
arms to level cutter right to left. Refer to tractor operator’s manual.
M. Lower cutter to work position. Adjust tractor
top link to position cutter top link as shown in Figure
2-6. This allows cutter to “float” during operation.
N. Adjust tractor sway chains, stabilizer bar or
equivalent to prevent side sway.
I. Repeat steps “G” and “H” to other driveline sec-
tion.
J. Deburr ends of driveline sections and clean
away all chips and filings. (Figure 2-5)
K. Apply multi-purpose grease to outside of male
driveline section. Assemble driveline and install on
tractor and cutter. Pull on each driveline section to
be sure yokes lock into place. Make certain driveline
shielding is in place and in good condition.
Figure 2-6 Flex-Link
9
SECTION III
OPERATING INSTRUCTIONS
3-1 GENERAL SAFETY
Only qualified people familiar with this operator’s
manual and tractor operator’s manual should operate this machine. Operator should wear hard hat,
safety glasses and safety shoes. The operator
should read, understand and practice all safety messages shown on the caution, warning and danger
decals affixed to the cutter to avoid serious injury or
death. It is recommended that tractor be equipped
with Rollover Protective System (ROPS) and a seat
belt be used. Before beginning operation, clear work
area of any objects that may be picked up and
thrown. Check for ditches, stumps, holes or other
obstacles that could upset tractor or damage cutter.
Always lower cutter to ground and allow blades to
come to a complete stop, set parking brake and turn
off tractor engine before leaving tractor operator’s
seat.
3-2 CUTTING HEIGHT ADJUSTMENT
The cutter should be operated at the highest position
that will give desired cutting results. (See “TIPS” on
next page) This will help prevent blades from striking
the ground, reducing blade wear and undue strain on
the machine. Cutting too much material may reduce
mulching action and leave visible clippings on the lawn
surface. The more frequently the lawn is mowed, the
better the mulching effect will be. Adjust as follows:
A. Raise cutter off ground using tractor 3-point
lift. SECURELY BLOCK CUTTER IN POSITION.
WARNING
THE CUTTER CAN FALL FROM
HYDRAULIC SYSTEM FAILURE. TO
AVOID SERIOUS INJURY OR DEATH,
SECURELY SUPPORT CUTTER BEFORE
WORKING UNDERNEATH
FIGURE 3-1 Caster Wheel
Spacers
Caster
Wheel
DANGER
STAY CLEAR OF ROTATING DRIVELINE. DO
NOT OPERATE WITHOUT DRIVELINE SHIELDS
IN PLACE AND IN GOOD CONDITION. FAILURE
TO HEED THESE WARNINGS MAY RESULT IN
PERSONAL INJURY OR DEATH.
DANGER
STAND CLEAR OF ROTATING CUTTER
BLADES UNTIL ALL MOTION HAS STOPPED.
TO AVOID ACCIDENTAL FALL AND POSSIBLE
INJURY FROM CUTTER,IT IS RECOMMENDED
THAT TRACTOR BE EQUIPPED WITH
ROLLOVER PROTECTIVE SYSTEM AND THAT A
SEAT BELT BE USED FOR ALL OPERATIONS.
shown in Figure 2-6.
C. With tractor at idle speed, engage PTO drive.
Advance throttle to 540 PTO rpm.
D. Place tractor in low gear and begin cutting.
Tractor forward speed should be controlled by gear
selection, not engine speed. For maximum cutting
efficiency, forward speed should allow cutter to
maintain a constant maximum blade speed.
B. Remove pin securing caster wheel to bracket.
(Figure 3-1) Remove caster wheel from arm.
C. Place amount of spacers on caster wheel to
give desired cutting height. With no spacers on the
bottom, a 3/4” cutting height is given.
D. Reinstall caster wheel into caster arm. Place
remaining spacers on caster wheel and install pin to
retain.
E. Repeat operation for all caster wheels. Make
certain all wheels are adjusted to the same height.
3-3 OPERATION
A. Perform BEFORE EACH USE maintenance
list in paragraph 4-1.
B. Start tractor. Lower cutter until it is supported
by caster wheels. Position tractor lower lift arms so
cutter lower links are parallel to ground, allowing cutter to “float” during operation. Adjust top link as
If tractor engine or cutter stalls, do not slip tractor
clutch to allow engine to retain speed as this will
exert undue strain on the implement drivetrain.
When stalling occurs, disengage PTO drive, move to
a cut area, set tractor throttle to idle, then re-engage
PTO drive.
Always cut up and down the face of slopes, never
across.
Check belt tension after first 8 hours
3-4 TRANSPORTING
Turn off PTO drive and fully raise tractor 3-point lift
before transporting. When implement is transported
on road or highway, day or night, use tractor flashing
warning lights unless prohibited by law. A slow moving vehicle (SMV) sign on the tractor must be visible
from the rear by approaching vehicles.
10
TIPS ON MOWING WITH A MULCHER
The Bush Hog MP 5/6 is a finishing mower with counter rotating blade sets designed to do a
superior job of mulching grass clippings. To get the maximum effectiveness from your MP
the tips listed below should be followed:
● Mow often - In general, mulching operations require more frequent mowing than would
conventional mowing procedures.
● Watch your speed - Normal conditions will allow a speed of up to approximately 5 mph,but
thick, heavy, damp conditions will require reduced ground speed.
● Mow at 540 RPM to keep tip speed at its maximum.
● Mow with a clean mower - Avoid grassy build-up under the deck.
● Mow with sharp blades - A sharp blade cuts cleaner.
● Wet grass will decrease distribution effectiveness and increase horsepower require-
ments. Leaves, on the other hand, may be more effectively mulched when they are
slightly damp.
● Mow at higher cutting heights - Remove and mulch no more than 2” - 2-1/2” of grass
length with each mowing. (Experts recommend not cutting off more than 1/3 of the
grass blade length at any given time.)
● Mow twice, at different height settings, (high, then low), if grass is extra tall.
● Keep your lawn clean, healthy and fertilized.
Figure 3-2 Sharp blades and a clean mower enhance mowing performance.
NOTE:
The MP 5/6 mulching mowers are equipped with
adjustable, removable baffles on the rear sides of the
outer blades. These baffles are factory installed in
the intermediate position for the most common grass
conditions. If extra fine mulching in light cutting conditions is desired, the baffles may be installed in the
lower position. When heavy cutting conditions exist,
the baffles may be completely removed to prevent a
grass build-up from occurring.
Removable Baffles
11
SECTION IV
MAINTENANCE
4-1 MAINTENANCE CHECK LIST
Perform scheduled maintenance as outlined below.
Lower implement to ground, turn off tractor, and set
parking brake before doing maintenance inspections
or work. Some checks may require raising machine
off ground and supporting with blocks. All bolts
should be torqued as indicated in torque chart
unless otherwise indicated.
WARNING
THE CUTTER CAN FALL FROM
HYDRAULIC SYSTEM FAILURE. TO
AVOID SERIOUS INJURY OR DEATH,
SECURELY SUPPORT CUTTER BEFORE
WORKING UNDERNEATH.
BEFORE EACH USE.
1. Check tractor tire air pressure. Refer to
tractor operator’s manual. Check mower tire pressure. Tire pressure should be 30 psi.
2. Check blades and spindles to be sure that no
foreign objects such as wire or steel strapping bands
are wrapped around them.
3. Check blade bolts for tightness. Tighten bottom
blade bolt to 76 ft./lbs., top blade bolts to 31 ft./lbs.
4. Inspect blades for wear. Replace if necessary
per paragraph 4-5. Use only genuine Bush Hog
replacement parts. If it is necessary to sharpen the
blades, remove the blades from the spindles before
sharpening. DO NOT sharpen blades while still
attached to mower.
5. Make certain all shields are in place and in
good condition. Repair or replace any missing or
damaged shields.
6. Inspect wheel(s) for wear, damage or foreign
objects. Repair or replace if necessary.
7. Perform BEFORE EACH USE lubrication per
paragraph 4-2.
Figure 4-1A
(6) 40 Hours
8.During operation, listen for abnormal sounds
which might indicate loose parts, damaged bearings,
or other damage. Correct any deficiency before continuing operation.
AFTER EACH USE
1. Clean all debris from machine especially underside of deck, underneath belt shield and off safety
decals. Replace any missing or illegible decals.
2. Inspect cutter for worn or damaged components. Repair or replace before next use. Any
replacement components installed during repair shall
include the components’ current safety decals speci-
fied by the manufacturer to be affixed to the component.
3. Store cutter in a dry place.
40 HOURS
1. Check belts for proper tension. Refer to paragraph 4-3.
4-2 LUBRICATION (Figures 4-1A, & B)
NOTE
The multi-purpose grease referenced in this
secftion is an NLGI Grade 2 type grease.
BEFORE EACH USE
1. Driveline Universal Joints - Apply multi-purpose
grease with grease gun.
2. Driveline Guard - Apply 2-3 shots of multi-pur-
pose grease with grease gun to plastic fitting.
3. Wheels - Apply multi-purpose grease wiith
grease gun.
4. Caster Pivot - Apply multi-purpose grease with
grease gun.
20 HOURS
5. Driveline - Disconnect PTO driveline, pull the
two sections apart, thoroughly clean old grease from
tubes and apply thin coat of multi-purpose grease to
outside of inner (male) section. Reassemble sections and install. Pull each section to be sure driveline and shields are securely connected. Make certain PTO shielding is in good condition.
40 HOURS
6. Input Gearbox - Add EP80W-90 gear oil, if
necessary, to bring oil level to check plug.
Figure 4-1B
(5) 20 Hours
(4)
(3)
Before Each Use
(2) Before Each Use
(1) Before Each Use
12
4-3 BELT ADJUSTMENT
4-4 BELT REPLACEMENT
Belt tensions should be checked every 40 hours to
get maximum life from drive belts and best performance from the cutter. Belt tension is adjusted by
increasing or decreasing the length of the spring on
the moveable idlers. For proper belt tension on the
mower, the spring lengths should be set at 2-7/8”.
(Figure 4-2) To adjust the spring length, loosen or tighten the 3/8” hex nuts on the spring adjustment rod until
the correct spring length is reached.
Figure 4-2 3/8” Hex Nuts - Spring Length Adjustment
Figure 4-3
UPPER BELT DIAGRAM
Use only genuine Bush Hog replacement parts. It is
not necessary to replace both belts if only one is
worn.
A. Remove right and left side shields.
B. Relieve spring tension by loosening the two
3/8” hex nuts on each spring adjustment rod. (Figure
4-2)
C. Remove old belts.
D. Install new belts as shown below. (Also refer
to the decal on underside of belt shield)
1. Belts must be installed at the same time. One
belt cannot be installed and tightened down before
the other.
2. Disconnect the upper adjustment rod from the
upper idler assembly.
3. Place both belts into the respective grooves
on the driving sheave.
4. Work the lower belt over the other sheaves.
After the lower belt is in place, complete the installation of the upper belt.
5. Connect the upper adjustment rod and the
upper idler assembly.
6. Tighten the compression springs on the upper
and lower drives to 2-7/8” long. Tighten the jam nuts
on the adjustment rods.
7. Replace all shields before operating machine.
Upper Idler Assembly
Driving Sheave
At Gearbox
Upper Adjustment Rod
LOWER BELT DIAGRAM
Driving Sheave
At Gearbox
Lower Adjustment Rod
13
4-5 BLADE REPLACEMENT
CAUTION
WEAR HEAVY WORK GLOVES TO PROTECT HANDS FROM SHARP EDGES.
WHEN TURNING BLADES, BE AWARE OF
OPPOSITE BLADE APPROACHING.
Always replace all (4) blades on an assembly to
retain balance. In addition to replacing blades when
they become worn and dull, they should also be
replaced if the uplift angle on the trailing side of the
blade becomes worn off. As the angle wears down,
the mulching action deteriorates.
A. Raise cutter using tractor hydraulic system
and use transport locks before changing blades.
B. Turn off tractor,set parking brake and remove
key.
C. Remove bolt and Belleville washer securing
bottom blade to spindle. Remove blade. Shaft washer will come off with the blade. (Figure 4-4)
D. Remove the four 3/8” x 1” capscrews and
belleville washers from the upper mulching assembly.
Remove mulching assembly. The blade bushing will
come off with the mulching assembly.
E. Remove the 3/8” - 24UNF x 7/8” Gr. 8 bladebolt and nut for each blade. Inspect the blade nut
shoulder and the blade bolts for wear. Replace if
necessary.
F. When installing new blades on the mulching
assembly, make sure that two blades are installed
on the top side of the assembly 180° from each
other and two on the bottom side of the assembly.
The blades must mount on the rotation “pads” for
proper operation. Assemble the (4) new blades to
the blade holder using the blade nuts, bolts, and flatwahsers. Tighten the bolts to 45 ft./lbs. Strike the
blade nut with a heavy hammer to seat, then tighten
again.
G. Insert the blade bushing in the center of the
mulching assembly so that the bushing flange is on
the top side of the assembly. Slide the mulching
assembly and flanged bushing over the spindle shaft
and secure mulching assembly to the upper blade
carrier using the (4) 3/8” - 16UNC x 3/4 Gr. 5 bolts
and belleville washers. Torque all (4) mulching
assembly attaching bolts to 31 ft./lbs.
H. Install the blade washer over the spindle
shaft. Install the bottom blade and torque the 1/2” -
20UNF Gr. 8 bolt to 76 ft./lbs. Note: The concave
side of the belleville washer must be toward the
blades. Do not substitute with a flat washer.
Figure 4-4 MP6 Blade Arrangement
3/8” - 24UNF x 7/8” Gr. 8 Blade Bolt & Blade Nut
3/8” x 1” Capscrew &
Belleville Washer
Bottom Blade Bolt &
Belleville Washer
Rotation Pad
Upper Blade Assembly
Shaft Washer
14
4-6 BLADE SPINDLE SERVICE (Figure 4-5)
If shaft bearings or other parts require replacement,
proceed as follows:
It is recommended that a Bush Hog dealer or other
qualified person service the blade spindle. If blade
spindles must be disassembled, special Bush Hog
spanner wrenches are supplied for this operation. The
Sheave Wrench is used on the outer shaft drive
sheave. The Shaft Wrench is used in the notches on
either end of the outer shaft. These wrenches are
stored in the tool box on the frame.
A. Wearing heavy gloves to protect hands,
remove blades from spindle, belts from sheaves and
remove complete spindle assembly from deck.
B. Remove lock nut above sheave on end of of inner
shaft.
C. Remove drive sheave from inner shaft. (A gear
puller may be required for this operation.) Remove the
woodruff key from the inner shaft.
D. Support the assembly on the blade carrier and
press the inner shaft and lower inner bearing out.
E. To remove the bearing from the shaft, support the
inner bearing race and press shaft out.
F. Press upper inner bearing out of the assembly.
G. Unstake sheave from upper end of outer shaft
and unstake blade carrier from lower end of outer shaft
using a blunt punch or chisel. (Use care so as not to
damage threads.) Clamp the blade carrier into a vise and
remove the drive sheave using the sheave wrench
(95778).
These threads are left handed - to loosen,
turn clockwise!
NOTE: If your vise is not large enough to clamp the
blade carrier, reinstall the blade onto the carrier. Tighten
the bolts only “finger tight”. The blade may then be
clamped in the vise. Also notice that it makes no difference if the blade carrier loosens first. If the blade carrier
comes off first, remove it from the vise and clamp the
sheave wrench into the vise with “pins” pointing upward.
Turn assembly upside down and place sheave onto
“pins”. The shaft wrench may then be used on the opposite end of the shaft to unscrew it from the sheave.
These threads are left handed - to loosen, turn clockwise.
H. Support the housing and press the outer shaft and
lower bearing out.
I. Press the upper bearing out of the housing.
J. Support the lower bearing and press the outer
shaft out.
BLADE SPINDLE REASSEMBLY
A. Install the inner shaft into the outer shaft by pressing upper and lower inner bearings into place. Press on
the inner and outer race of the bearings
until the bearings bottom out on the shoulder of the inner
shaft.
B. Install the outer shaft sub-assembly into the housing by pressing the upper and lower outer bearings into
place. Press on the inner and outer race of the bearings
simultaneously
shoulder of the outer shaft.
NOTE
simultaneously
until the bearings bottom out on the
Figure 4-5 Blade And Spindle Assembly
Nut for Inner Shaft
Flat Washer
Drive Sheave for Inner Shaft
Drive Sheave for Outer Shaft
Upper Bearing for Inner Shaft
Woodruff Key
Blade Bushing
Blade Nut
Bolt
Flatwasher
Upper Blade
Blade Nut
Belleville Washe
Inner Shaf
Upper Bearing for Outer Shaft
Outer Shaft
Lower Bearing for Inner Shaft
r &
Bolt
t
Shaft Wrench
Sheave Wrench
Hub
Lower Bearing for Outer Shaft
Blade Carrier
Upper Blade Disc
Belleville Washer &
Bolt
Shaft Washer
Lower Blade
C. Thread the outer shaft sheave and blade car-
rier onto the assembly.
These threads are left
handed - to tighten, turn counter-clockwise.
Clamp the blade carrier in a vise and insert the
sheave wrench pins into the outer drive sheave.
Using a torque wrench in conjunction with the
sheave wrench, tighten the assembly to 200 ft./lbs.
Refer to Fig. 4-6 on following page for the required
torque for your specific torque wrench.
D. Restake the blade carrier and drive sheave
into the notches of the outer shaft.
E. Install the woodruff key, sheave, flat washer
and nut onto the inner shaft and torque the nut to 76
ft./lbs.
F. Place the blade bushing onto the inner shaft
with the ring side toward the bearing (Fig. 4-5)
Install the upper blade disc with bolts and belleville
washers onto the blade carrier.Torque to 31 ft./lbs.
G. Install the shaft washer, lower blade belleville
washer and blade bolt onto the inner shaft and
torque the blade bolt to 76 ft./lbs.
15
Figure 4-6 Torque Wrench Operation
A
6”
TORQUE WRENCH CHART
When using a torque wrench in conjunction with a Bush Hog shaft or sheave wrench,
the following chart must be used to achieve the correct torque of 200 ft./lbs.
Torque Wrench 12” 14” 16” 18” 20” 22”
Length (A)
Torque Indicator 133 140 145 150 154 157
Must Show ft./lbs. ft./lbs. ft./lbs. ft./lbs. ft./lbs. ft./lbs.
4-7 TROUBLESHOOTING
Troubleshooting procedures are listed in Table 4-1 below. If the problem cannot be solved or replacement parts
are necessary, contact your authorized Bush Hog dealer. Please have ready your machine name, model number, serial number, purchase date and exact cause or description of problem.
Table 4-1 Troubleshooting
PROBLEM PROBABLE CAUSE REMEDY
Uneven Cut Cutter not level side to side See SECTION III.
Streaking or Windrowing Possible build-up of Clean cutter.
Noisy Cutter Loose components. Check all bolts for tightness.
Rapid Blade Wear Blade contacting Adjust cutting height to
(cutting edge) ground. eliminate ground contact.
Rapid Blade Cutter not being Set tractor throttle for
Wear operated at rated PTO speed. proper PTO speed.
Cutter Vibrating Cutter not being operated Set tractor throttle for
or front to rear.
Belt slipping. Adjust belt per paragraph 4-3.
Worn or bent blade(s). Replace blade(s).
material under cutter.
Cutter not level. See SECTION III.
Worn blades. Replace blades.
Belt slipping. Adjust belt per paragraph 4-3.
Low oil in gearbox. Check oil per paragraph 4-2.
Use lower gear.
at rated PTO speed. proper PTO speed.
Blade(s) bent. Replace blades.
Foreign object wrapped Remove object.
around spindle or blade.
16
SECTION V
DEALER ASSEMBLY
CAUTION
THE FOLLOWING SAFETY PRECAUTIONS
SHOULD BE THOROUGHLY UNDERSTOOD
BEFORE ATTEMPTING MACHINE ASSEMBLY.
1. Wear personal protective equipment such as,
but not limited to, protection for eyes, ears, feet,
hands, lungs and head when assembling the equipment. Do not wear loose clothing or jewelry that may
catch on equipment moving parts.
2. Do not lift heavy parts or assemblies. Use
crane, jack, tackle, fork trucks or other mechanical
devices.
3. Select an area for assembly that is clean and
free of any debris which might cause persons working on the assembly to trip.
4. Arrange parts to be assembled neatly in the
work area and have tools or other mechanical assisting devices in easy reach.
5. Inspect all parts and assemblies thoroughly and
remove any sharp edges, grease, oil or dirt whichmight cause pieces to slip when handling.
6. Preview the assembly instructions in your operator’s manual before proceeding further.
7. If the assembly instructions call for parts or
assemblies to be blocked up, use only blocking
material that is in good condition and is capable of
handling the weight of the assembly to be blocked.
Also, insure that the blocking material is on a clean,
dry surface.
8. Never put hands or any other part of body
under blocked up assemblies if at all possible.
9. Always wear goggles or safety glasses when
hammering, grinding, or drilling metal parts.
10. If the assembly calls for welding or cutting, be
sure that there are no flammable materials close at
hand and that bystanders have taken necessary precautions.
Figure 5-1
Flex Link
Mast Half
Mast
Support
AFTER COMPLETING ANY ASSEMBLY STEP,
THOROUGHLY READ THE NEXT STEP IN THE
ASSEMBLY INSTRUCTIONS BEFORE PROCEEDING WITH THAT STEP.
11. After completing assembly, thoroughly inspect
the machine to be sure that all nuts, bolts, hydraulic
fittings or any other fastened assemblies have been
thoroughly tightened.
12. After completing assembly, be sure that all
safety locking devices or guards are in place.
13. Before operating the machine, thoroughly
read the operation section of this manual.
14. Before operating the machine, read the maintenance section of this manual to be sure that any
parts requiring lubrication such as gearboxes are full
to avoid any possible damage.
BEFORE OPERATING THE EQUIPMENT, IF YOU
HAVE ANY QUESTIONS REGARDING THE
PROPER ASSEMBLY OR OPERATION, CONTACT YOUR AUTHORIZED BUSH HOG DEALER
OR REPRESENTATIVE.
5-1 BASE UNIT ASSEMBLY
A. Attach lower lift links to deck assembly using
5/8 x 2-1/2 bolts, flatwashers, lockwashers, hex nuts
and pivot bushings. (Figure 5-1)
B. Install lift pins onto lower links, securing with
7/8” lockwashers and hex nuts.
C. Attach mast halves to deck assembly using 1/2
x 1-1/2” bolts, lockwashers and hex nuts.
D. Loosely attach two caster arms to the front of
the mower deck using 5/8 x 3-1/2” bolts, l;ockwashers and hex nuts. Loosely attach the remaining two
caster arms to the rear of the mower deck using 5/8
x 3-1/2” bolts, lockwashers and hex nuts in each
caster arm. Attach mast supports to lugs at the rear
of the mower deck using 1/2 x 1-1/4” bolts, lockwashers and hex nuts.
Gearbox
Lower Link
Caster Arm
Spacers
17
E. Fasten mast supports and upper flex link to
mast halves using 1/2 x 5” bolt,pivot tube and locknut.
F. Place one long spacer on the caster stems
and insert into caster arms. Place three long spacers
and two short spacers on the caster stem above the
caster arms. this arrangement will give a cutting
height of approximately 1-3/4” . Secure with lynch
pin retainers. With weight of cutter resting on all four
wheels, ensure that cutter is level. Tighten all bolts
on mounting brackets.
Figure 5-2 Front Roller
3/8 x 1” Bolt, Lockwasher
and Flatwasher
Retaining Pin
G. Install front roller by securing the right and left
roller mounts to the deck in the holes provided by
using 3/8 x 1” carriage bolts, flatwashers and lockwashers. (Figure 5-2) Assemble roller, roller shaft,
retaining pin and roll pin as shown.
H. Fill gearbox with EP80W-90 gear oil until oil
level is at check plug on side of gearbox housing.
Allow time for oil to seep through bearings into lower
housing. (Capacity is 1 quart) Replace solid fill plug
with breather plug supplied in operator’s manual
package.
Roller Mounts
Roller Shaft
Roller
Roll Pin
18
SAFETY DECALS
To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damage
can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide
safety decals for any of our products in the field at no charge. Contact your authorized Bush Hog dealer for
more information.
82619
78608
50012615
82617
82618
60873
50012616
19
Wrench
Size “A”
AMERICAN
Bolt Head Markings
SAE Grade 2
(No Dashes)
SAE Grade 5
(3 Dashes)
SAE Grade 8
(6 Dashes)
TORQUE SPECIFICATIONS
Proper toque for American fasteners used on Bush Hog equipment.
Recommended Torque in Foot Pounds (Newton Meters).*
BOLT DIAMETER
Bolt
Diameter “B”
WRENCH (IN.) “B” AND SAE SAE SAE
SIZE (IN.) “A” THREAD SIZE GRADE 2 GRADE 5 GRADE 8
7/16 1/4 - 2O UNC 6 (7) 8 (11) 12 (16)
7/16 1/4 - 28 UNF 6 (8) 10 (13) 14 (18)
1/2 5/16 - 18 UNC 11 (15) 17 (23) 25 (33)
1/2 5/16 - 24 UNF 13 (17) 19 (26) 27 (37)
9/16 3/8 - 16 UNC 20 (27) 31 (42) 44 (60)
9/16 3/8 - 24 UNF 23 (31) 35 (47) 49 (66)
5/8 7/16 - 14 UNC 32 (43) 49 (66) 70 (95)
5/8 7/16 - 20 UNF 36 (49) 55 (75) 78 (106)
3/4 1/2 - 13 UNC 49 (66) 76 (103) 106 (144)
3/4 1/2 - 20 UNF 55 (75) 85 (115) 120 (163)
7/8 9/16 - 12 UNC 70 (95) 109 (148) 153 (207)
7/8 9/16 - 18 UNF 79 (107) 122 (165) 172 (233)
15/16 5/8 - 11 UNC 97 (131) 150 (203) 212 (287)
15/16 5/8 - 18 UNF 110 (149) 170 (230) 240 (325)
1-1/8 3/4 - 10 UNC 144 (195) 266 (360) 376 (509)
1-1/8 3/4 - 16 UNF 192 (260) 297 (402) 420 (569)
1-5/16 7/8 - 9 UNC 166 (225) 430 (583) 606 (821)
1-5/16 7/8 - 14 UNF 184 (249) 474 (642) 668 (905)
1-1/2 1 - 8 UNC 250 (339) 644 (873) 909 (1232)
1-1/2 1 - 12 UNF 274 (371) 705 (955) 995 (1348)
1-1/2 1 - 14 UNF 280 (379) 721 (977) 1019 (1381)
1-11/16 1-1/8 - 7 UNC 354 (480) 795 (1077) 1288(1745)
1-11/16 1-1/8 - 12 UNF 397 (538) 890 (1206) 1444 (1957)
1-7/8 1-1/4 - 7 UNC 500 (678) 1120 (1518) 1817 (2462)
1-7/8 1-1/4 - 12 UNF 553 (749) 1241 (1682) 2013 (2728)
2-1/16 1-3/8 - 6 UNC 655 (887) 1470 (1992) 2382 (3228)
2-1/16 1-3/8 - 12 UNF 746 (1011) 1672 (2266) 2712 (3675)
2-1/4 1-1/2 - 6 UNC 870 (1179) 1950 (2642) 3161 (4283)
2-1/4 1-1/2 - 12 UNF 979 (1327) 2194 (2973) 3557 (4820)
Proper torque for metric fasteners used on Bush Hog equipment.
METRIC
Wrench
Size “A”
Numbers appearing on bolt heads
indicate ASTM class.
8.8
Bolt
Diameter “B”
*Use 75% of the specified torque value for plated
fasteners. Use 85% of the specificed torque
values for lubricated fasteners.
Recommended torque in foot pounds (newton Meters).*
WRENCH BOLT
SIZE DIA. ASTM ASTM ASTM ASTM
(mm) “A” (mm) “B” 4.6 8.8 9.8 10.9
8 5 1.8 (2.4) 5.1 (6.9) 6.5 (8.8)
10 6 3 (4) 8.7 (12) 11.1 (15)
13 8 7.3 (10) 21.1 (29) 27 (37)
16 10 14.5 (20) 42 (57) 53 (72)
18 12 25 (34) 74 (100) 73 (99) 93 (126)
21 14 40 (54) 118 (160) 116 (157) 148 (201)
24 16 62 (84) 167 (226) 181 (245) 230 (312)
30 20 122 (165) 325 (440) 449 (608)
33 22 443 (600) 611 (828)
36 24 211 (286) 563 (763) 778 (1054)
41 27 821 (1112) 1138 (1542)
46 30 418 (566) 1119 (1516) 1547 (2096)
20
P.O. Box 1039 llSelma, AL 36702-1039
Telephone (334) 874-2700
ll
www.bushhog.com
Loading...