Bush Hog 1035 User Manual

1035

FRONT END

LOADER

Published 05/11 MATERIAL HANDLING PARTS MANUAL

PARTS MANUAL

SECTION 1-31

PA RTS ORDERING GUIDE

The following instructions are offered to help eliminate needless delay and error in pro­cessing purchase orders for the equipment in this section.

1. The Parts Section is prepared in logical sequence and grouping of parts that belong
to the basic machine featured in this manual. Part Numbers and Descriptions are given
to help locate the parts and quantities required.

2. The Purchase Order must include the name and address of the person or organiza­tion ordering the parts, who should be charged, and if possible, the serial number of the
machine for which the parts are ordered.

3. The Purchase Order must clearly list the quantity of each part, the complete and correct
part number (be sure to include all periods), and the basic name of the part.

4. The Manufacturer reserves the right to substitute parts where applicable.

5. Some parts are unlisted items which are special production items not normally stocked
and are subject to special handling. Request a quotation for such parts before sending
a Purchase Order.

6. The Manufacturer reserves the right to change prices without prior notice.
For maximum safety and to guarantee optimum product reliability, always

use genuine BUSH HOG Parts. The use of inferior replacement parts may
causepremature or catastrophic failure which could result in serious injury
or death.Direct any questions regarding parts to:

BUSH HOG

2501 Griffin Ave.
Selma, AL 36703
www.bushhog.com
Contact Us
800-304-2836

©2009 Alamo Group Inc.

LIMITED WARRANTY

Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush
Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for
non-commercial, state and municipalities’ use and ninety (90) days for commercialuse from date of retail sale. The
obligation of Bush Hog to the purchaser under this warranty is limited to the repair or replacement of defective
parts.

Replacement or repair parts installed in the equipment covered by this limited warranty are warranted for ninety
(90) days from the date of purchase of such part or to the expiration of the applicable new equipment warranty
period, whichever occurs later. Warranted parts shall be provided at no cost to the user at an authorized Bush Hog
dealer during regular working hours. Bush Hog reserves the right to inspect any equipment or parts which are
claimed to have been defective in material or workmanship.

DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES

Bush Hog’s obligation under this limited warranty, to the extent allowed by law, is in lieu of all warranties, implied or
expressed, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE and any liability for incidental and consequential damages with respect to the sale or use of the items
warranted. Such incidental and consequential damages shall include but not be limited to: transportation charges
other than normal freight charges; cost of installation other than cost approved by Bush Hog; duty; taxes; charges
for normal service or adjustment; loss of crops or any other loss of income; rental of substitute equipment,
expenses due to loss, damage, detention or delay in the delivery of equipment or parts resulting from acts beyond
the control of Bush Hog.

THIS LIMITED WARRANTY SHALL NOT APPLY:

1. To vendor items which carry their own warranties, such as engines, tires, and tubes.

2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident.

3. If parts not made or supplied by Bush Hog have been used in connection with the unit, if, in the sole judgement
of Bush Hog such use affects its performance, stability or reliability.

4. If the unit has been altered or repaired outside of an authorized Bush Hog dealership in a manner which, in the
sole judgement of Bush Hog, affects its performance, stability or reliability.

5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic fluid, worn
blades, or to normal deterioration of such things as belts and exterior finish due to use or exposure.

6. To expendable or wear items such as teeth, chains, sprockets, belts, springs and any other items that in the
company’s sole judgement is a wear item.

NO EMPLOYEE OR REPRESENTATIVE OF BUSH HOG IS AUTHORIZED TO CHANGE THIS LIMITED
WARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE IN
WRITING AND SIGNED BY BUSH HOG’S SERVICE MANAGER, 2501 GRIFFIN AVE., SELMA, ALABAMA

36703.

Record the model number, serial number and date
purchased. This information will be helpful to your
dealer if parts or service are required.

MODEL NUMBER ________________________________
SERIAL NUMBER ________________________________
DATE OF RETAIL SALE ___________________________

MAKE CERTAIN THE WARRANTY
HAS BEEN FILED WITH BUSH HOG
SELMA, ALABAMA

BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL

TABLE OF CONTENT

1035 FRONT END LOADER

ITEM PAGE

FRAMES

Mainframe and Subframe ..............................................................................1-31A-1

MOUNTING KITS

Mounting Kit 2-7426 ..................................................................................1-31B-1

Mounting Kit 2-7439 ..................................................................................1-31B-2

ATTACHMENTS

Bucket..........................................................................................................................................................................................1-31C-1

HYDRAULICS

Hydraulic System)........................................................................................................................................................................1-31D-1

Hydraulic Valve (Prince LVS Series) ...........................................................................................................................................1-31D-2

Hydraulic Cylinder (Lift and Bucket..............................................................................................................................................1-31D-4

Hose Kit, New Holland TC21DA, TC23DA, TC24DA, TC26DA,

Case IH DX21, DX23, DX24, DX26 .............................................................................................................................1-31E-1

Hose Kit, Kioti CK20.....................................................................................................................................................................1-31E-2

Control Valve and Plumbing Kit 2-7449 Case IH DX21, DX23, DX24, DX26

New Holland TC18, TC21D, TC23DA, TC24D, TC26DA..............................................1-31E-3

MAY, 2011

GRILL GUARD

Grill Guard Kit Case IH DX21, DX23, DX24, DX26

New Holland TC21DA, TC23DA, TC24DA, TC26DA..........................................................................................1-31F-1

Grill Guard Kit Kioti CK20S ..........................................................................................................................................................1-31F-2

DECALS

Decal Location .............................................................................................................................................................................1-31G-1

Decal Pictorials ............................................................................................................................................................................1-31G-2

NOTES:

BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL

1035 MAINFRAME AND SUBFRAME

MAY, 2011

REF. PART DESCRIPTION QTY.

NO. NO. REQ’D.

1 52454 Boom Assy., With Decals 1
2 52453 Sideframe Assy., Left With Decals 1
3 52452 Sideframe Assy., Right With Decals 1
4 52350 Cylinder Assy., Lift (Code Nm) 2
5 52356 Cylinder Assy., Bucket (Code Nn) 2
6 52638 Leveling Tube Assy. 1
7 51965-3 Pin Assy., 1 X 3.12 4
8 51967 Hitch Pin 2

9 44756-1 Linch Pin 2
10 52107-2 Pin, 1x 4.50 4
11 52107-1 Pin, 1x 4.00 4
12 47046 Shoulder Bolt, 3/8-16 X 1 4
13 ------- Locknut, 3/8-16 6
14 ------- Capscrew, 5/16-18 X 1.75 8
15 ------- Locknut, 5/16-18 9
16 6075-2 Fitting. Grease, 1/8-27 12
17 52399 Parking Stand Leg 2
18 52415 Parking Stand Strut 2
19 ------- Capscrew , 3/8-16 X 2.50 2
20 41902-21 Clevis Pin, 1/2 X 3.50 2
21 44756-2 Linch Pin 2
22 6040-10 Retainer Ring, 7/8 4

REF. PART DESCRIPTION QTY.

NO. NO. REQ’D.

23 ------- Capscrew, 5/16-18 X 1 1
24 52400 Tightener Band 1
25 52418 Indicator Rod Assy. 1
26 50057411 Decal,Bush Hog Deal 2
27 50069069 Decal,Model 1035 2
29 46778 Decal, Danger 2
30 51902 Decal, Warning 2
31 50058089 Decal, Bush Hog 1
32 51900 Decal, Danger 1
33 48280 Decal, Warning 1
34 51904 Decal, Warning 1
35 51906 Decal, Peligro (Danger, Spanish) 1
36 51901 Decal, Warning 1
37 52740 Decal, Warning 1
38 00776964 Seal, Manual Canister (Not Shown) 1
39 00776031 Canister With Cap, Includes Item 40 1
40 ------- Flatwasher, 1/4 2
41 ------- Locknut, 1/4-20 2

1-31A-1

BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL

MOUNTING KIT 2-7426

Case IH DX21, DX23, DX24 and DX26 FWA

New Holland TC21DA, TC23DA, TC24DA, TC26FWA

MAY, 2011

REF. PART DESCRIPTION QTY.

NO. NO. REQ’D.

1 52479 Mounting Bracket, Mid, Left 1
2 52478 Mounting Bracket, Mid, Right 1
3 50249 Plate 2
4 52472 Spacer Plate 2
5 ------- Capscrew, M16-2 X 50 Gr 8.8 8
6 ------- Capscrew, 1/2-13 X 1.75” 2
7 ------- Capscrew, 1/2-13 X 2.00” 6
8 ------- Locknut, 1/2-13 8
9 ------- Lockwasher, 5/8 8

1-31B-1

BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL

MOUNTING KIT 2-7439

Kioti CK20S FWA Gear and HST

MAY, 2011

REF. PART DESCRIPTION QTY.

No. No. Req’d.

1 52444-1 Mounting Bracket, Mid, Left 1
2 52444-2 Mounting Bracket, Mid, Right 1
3 52105 Plate, Support 2
4 42672-22 Capscrew, 14mm-1.50mm X 55mm 8
5 42672-24 Capscrew, 12mm-1.25mm X 35mm 8
6 41837-6 Lockwasher, 9/16 8
7 41837-5 Lockwasher, 1/2 8
8 42502-10 Flatwasher, 1/2 8

1-31B-2

BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL

BUCKET ASSEMBLY

MAY, 2011

REF. PART DESCRIPTION QTY.

NO. NO. REQ’D.

1 * Bucket, 48" Std. Duty (Order from Whole Goods) 1

* Bucket, 54" Std. Duty (Order from Whole Goods) 1
2 52431 Cutting Edge, Side (Std. Duty) 2
3 22542-2 Cutting Edge, Bottom (48" Std.) 1

22542-21 Cutting Edge, Bottom (54" Std.) 1

1-31C-1

BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL

HYDRAULIC SYSTEM

1035 Models

MAY, 2011

REF. PART DESCRIPTION QTY.

NO. NO. REQ’D.

1 38290-17 Hose, 1/4 X 21 2
2 38290-16 Hose, 1/4 X 14 2
3 38290-12 Hose, 1/4 X 19 2
4 38290-7 Hose, 1/4 X 36 2
5 *52387 **Tube, Oil Line(Lcb) 1
6 *52388 **Tube, Oil Line(Lcr) 1
7 *52389 **Tube, Oil Line (Tcr) 1
8 *52390 **Tube, Oil Line (Tcb) 1

9 52108-1 Rubber Spacer 4
10 51968 Pad, Oil Line 4
11 51961 Clamp, Oil Line 2
12 52414 Shield, Oil Line 1
13 42848-1 Flange Nut 4
14 8137-1 Tie Strap, 3/16, Plastic 2

36409 Replacement, Oil Line Tee Fitting
36410 Replacement, Oil Line 90° Fitting
36411 Replacement, Oil Line Straight Fitting
36412 Repair, Oil Line Tube Splice Fitting

*NOTE: If a fitting or oil line is damaged, it can be repaired with replace­ments listed rather than
replacing the complete oil line. No specific tools are required, only common
wrenches and a hacksaw.
**NOTE: Because of difficulty in shipping oil line tubes, they have been bro­ken down into sections for shipping. The two sections of tube must be
threaded together to construct the original one piece tube which is not avail­able for repairs.

1-31D-1

BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL

HYDRAULIC VALVE

PRINCE (LVS SERIES Valve)

MAY, 2011

41

1-31D-2

BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL

HYDRAULIC VALVE

PRINCE (LVS SERIES Valve)

REF. PART DESCRIPTION QTY.

NO. NO. REQ’D.

1 52253 Seal Kit, Prince LVS Valve 1
2 43637-3 Relief Valve (2000 PSI) 1
3 55764 Plug, Load Check 2
4 52254 Float Kit (Includes Items 6, 7, 8, 10, 11, 12, 13, 14, 15, 16, 17, And 18) 1
5 52255 Regen Kit (Includes Items 6, 7, 9, 10, 11, 12, 13, 14, 15, 16, 17, And 18) 1
7 44476-3 End Cap, Manufacturer’s Part Number (Hc-V-Aa25) Stamped On End Cap 2

Identifies Valve And Relief Setting.)
19 43517 Handle, Valve, Standard 1
20 ------- Hexnut, 7/16-20 1
21 ------- Lockwasher, 7/16" 1
22 52172 Boot, Rubber, Valve Handle 1
23 38902 Ball, Handle 1
24 -------- Tie Strap, 3/16" Wide X 13" Long 1
25 52251 Disk, Adapter, Handle To Linkage 1
26 44743-4 Capscrew, Socket Head, 5/16-24 X 3/4" 3
27 51075 Rod End, Assembly 2
28 38900-4 Rod End 1
29 51076 Stud, Spool 1
30 ------- Hexnut, 5/16-24 3
31 52252 Clevis, Lock, Housing 1
32 44743-7 Capscrew, Socket Head, 1/4-20 X 1-3/4" 2
33 44743-6 Capscrew, Socket Head, 1/4-20 X 3/4" 1
34 ------- Flatwasher, 1/4" 1
35 52250 Knob, Spool Lock 1
36 52247 Handle, Spool Lock 1
37 52246 Blade Lock 1
38 52249-1 Ring, Retaining, External 1
39 52248 Spring 1
40 G273625 Roll Pin 1
41 52205 Valve Assembly 1

MAY, 2011

NOTE: Valve spools are one-piece construction, which includes spool ends for connecting handle linkage.

Valve spools and body are matched parts and are not available separately.
Individual items not listed in repair parts listing are not available separately.

1-31D-3

BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL

HYDRAULIC CYLINDERS - BUCKET and LIFT

MAY, 2011

REF. PART DESCRIPTION QTY.

NO. NO. REQ’D.

1 52346 Rod, Cylinder, 1" (Lift Cylinder) 1

52352 Rod, Cylinder, 1" (Bucket Cylinder) 1
2 * Seal, Wiper 1
3 * Seal, Rod 1
4 44027 Head, Cylinder (Lift Cylinder) 1

45313 Head, Cylinder (Bucket Cylinder) 1
5 * Ring, Wear 1
6 * Washer, Backup 1
7 * O-Ring 1
8 * Seal, Piston 1
9 * O-Ring 1

10 46479 Piston (Lift Cylinder) 1

45311 Piston (Bucket Cylinder) 1

11 * Ring, Wear 1
12 32903-4 Locknut, 3/4" (Lift Cylinder) 1

47264-18 Locknut, 3/4" (Bucket Cylinder) 1

13 52349 Tube, Cylinder (Lift Cylinder) 1

52355 Tube, Cylinder (Bucket Cylinder) 1

14 * Wire, Retaining 1
15 46525 Repair Kit, (* Parts In Kit)(Lift Cylinder) 1

45318 Repair Kit, (* Parts In Kit)(Bucket Cylinder) 1

1-31D-4

BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL

HOSE KIT 2-7441

CASE IH DX21, DX23, DX24, DX26

New Holland TC21DA, TC23DA, TC24DA TC26DA

MAY, 2011

REF. PART DESCRIPTION QTY.

NO. NO. REQ’D.

1 6137-11 Coupler, Quick, M 4
2 32837-9 Hose, 1/4 X 40" 4
3 32845-1 Fitting, Elbow, 9/16-18 Jic X 9/16-18 O-Ring 4
4 34853-77 Nylon Sleeve, 1-19/32 X 40" 2
5 8137-3 Strap, Adjustable, 1/2 X 20" 2
6 4838-18 Dust Cover, Black 4
7 36240-5 Spiral Band, Blue, 5/8" 2
8 36240-6 Spiral Band, Red, 5/8" 2
9 36240-7 Spiral Band, Yellow, 5/8" 2

10 36240-8 Spiral Band, Green, 5/8" 2

1-31E-1

BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL

HOSE KIT 2-7440

KIOTI CK20 with Mid Mounted Valve

MAY, 2011

REF. PART DESCRIPTION QTY.

NO. NO. REQ’D.

1 6147-9 Coupling Body 4
2 6137-9 Coupling, M, 1/4” 4
3 32837-17 Hose, 1/4 X 44 4
4 32845-1 Fitting, Elbow, 90°, 9/16-18 X 9/16-18 4
5 48670-2 Fitting, Adapter, Adj. O-Ring Hex, 9/16 4
6 34853-39 Sleeve, Nylon, 1.59 X 47 2
7 4838-7 Dust Cap 4
8 4838-11 Dust Plug 4

9 36240-5 Spiral Band, Blue, 5/8 2
10 36240-6 Spiral Band, Red, 5/8 2
11 36240-7 Spiral Band, Yellow, 5/8 2
12 36240-8 Spiral Band, Green, 5/8 2
13 8137-3 Strap, Adjustable, .50 X 20 2

1-31E-2

BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL

VALVE AND PLUMBING KIT 2-7449

CASE IH DX21, DX23, DX24, DX26

NEW HOLLAND TC21DA, TC23DA, TC24DA, TC26DA

MAY, 2011

Ref. Part Description Qty.

No. No. Req’d.

1 52205 Valve, Prince LVS, Series, 2-Spool (2000 Psi) 1
2 43517 Handle, Valve, Standard 1
3 ------- Hexnut, 7/16-20 1
4 ------- Lockwasher, 7/16” 1
5 52172 Boot, Valve Handle Linkage 1
6 38902 Ball, Valve Handle 1
7 44277-2 Elbow, 90°, 9/16-18 SAE O-Ring M X 9/16-18 JIC F 2
8 42062-6 Fitting, Str., 9/16-18 SAE O-Ring M X 9/16-18 JIC F 2

9 31221-4 Fitting, Str., 3/8 NPT M X 9/16-18 Jic M 4
10 6147-4 Coupler, F Quick, 3/8” 4
11 36240-9 Spiral Band, Plastic, Blue, 1” 1

36240-10 Spiral Band, Plastic, Red, 1” 1
36240-11 Spiral Band, Plastic, Yellow, 1” 1

36240-12 Spiral Band, Plastic, Green, 1” 1
12 52202 Plate, Valve Mounting 1
13 52429 Bracket, Valve Mounting 1
14 ------- Capscrew, 3/8-16 X 2-1/4” Grade 5 2
15 ------- Locknut, 3/8-16 4
16 44274-1 Plug, Square Tube 1
17 52189 Shield, Series Valve, With Decals 1

Ref. Part Description Qty.

No. No. Req’d.

18 52204 Decal, Single Handle Control 1
19 52074 Decal, Warning: Do Not Tamper 1
20 52203 Decal, Lock/Unlock 1
21 ------- Capscrew, 5/16-18 X 1” Grade 5 2
22 ------- Capscrew, 5/16-18 X 3/4” Grade 5 1
23 ------- Lockwasher, 5/16” 3
24 ------- Capscrew, 3/8-16 X 1-1/4” 2
25 44269-7 Hose, 3/8x36” 3/4-16 Sae O-Ring M X 3/4-16 Jic F S 3
26 34853-75 Sleeve, Hose, 36” Long 3
27 40252-2 Elbow, 45°, 3/8-18 SAE O-Ring M X 3/4-16 JIC F 3
28 38226-2 Elbow, 45°, 3/4-16 JIC M X 3/4-16 JIC F S 3
29 8137-3 Strap, Adjustable, 1/2” Wide X 20” Long 4
30 36251-8 Hose, 1/4 X 38”, 3/8 NPT M X 9/16-18 JIC F 4
31 34853-55 Sleeve, Hose, 1.25 X 40” Long 4
32 6137-4 Coupler, M Quick, 3/8 4
33 36240-5 Spiral Band, Plastic, Blue, 5/8” 1

36240-6 Spiral Band, Plastic, Red, 5/8” 1
36240-7 Spiral Band, Plastic, Yellow, 5/8” 1
36240-8 Spiral Band, Plastic, Green, 5/8” 1

1-31E-3

BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL

GRILL GUARD KIT 2-7448

Case IH DX21, DX23, DX24, DX25, Compatable with Case IH LX112 Loader

New Holland TC21DA, TC23DA, TC24DA, TC26DA

MAY, 2011

Ref. Part Description Qty.

No. No. Req’d.

1 52061 Grille Guard, Bumper 1
*2 52065 Bar, Latch, Grille Guard 1
*3 6043-27 Spring, Compression, .73 O.D. X 3.69" Long, Grille Guard Latch 2
*4 ------- Capscrew, 5/16-18 X 2" 2
*5 ------- Nut, Flange Head, 5/16-18 Full Thread 2

6 52639 Plate, Mounting, Grille Guard 2

7 50517 Plate, Spacer, Grille Guard, 5/16" 2

8 ------- Bolt, Carriage, 5/8-11 X 1-3/4" 2

9 ------- Locknut, 5/8-11, Nylon Insert (Top Lock) 2

10 ------- Capscrew, 1/2-13 X 1-3/4" Grade 5 4
11 ------- Kocknut, 1/2-13, Type N (Center Lock) 4

1-31F-1

BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL

GRILL GUARD KIT 2-7626

Kioti CK20S, HST

MAY, 2011

Ref. Part Description Qty.

No. No. Req’d.

1 53959 Grille Guard Assembly 1
2 ------- Bolt, 1/2”-13 X 1 3/4” 4
3 ------- Flatwasher 1/2” N-Sae 8
4 ------- Locknut 1/2” 4

1-31F-2

BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL

DECALS - PLACEMENT

MAY, 2011

REF. PART DESCRIPTION QTY.

NO. NO. REQ’D.

1 50069069 Model Decal 2
2 50069110 Operators Manual 1
3 50057411 Logo Decal 14-1/2” 2
4 50058089 Logo Decal 11” 1
5 52203 Decal, Push/Lock/Pull 1
6 52074 Decal, Warning - Relief Valve 2
7 51902 Decal, Warning - To Avoid 2
8 46778 Decal, Danger 2

9 51904 Decal, Read Manual 1
10 51906 Decal, Danger Peligro 1
11 03200347 SMV Reflector Sign 1
12 00776031 Canister Assy, 1
13 52740 Decal, Warning Oil Leak 1
14 51901 Decal, Large Heavy 1
15 48280 Decal, One Call 1

1-31G-1

BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL

DECALS - PICTORIALS

1

4

3

5

MAY, 2011

2

7

6

8

11

10

9

REF. PART DESCRIPTION QTY.

NO. NO. REQ’D.

12

1 50057411 Logo Decal Bush Hog 14.5” x 3.2” 1

50058089 Logo Decal Bush Hog 11” x 2.42” 1
2 50069069 Model1035 Decal 2
3 52740 Warning Oil Leaks 2
4 52203 Warning Lock Valve In Transport 1
5 52902 Warning Decal, To Avoid 1
6 46778 Danger Decal 1
7 51904 Danger Crushing, Electrocution, Falling Hazard 2
8 51906 Danger, Peligro Decal 1
9 51901 Danger, Large Heavy 1

10 48280 Decal, One Call 1
11 52074 Decal, Warning Relief Valve 1
12 52204 Valve Operation Decal 1

1-31G-2

2501 Griffin Ave.• Selma, AL 36703

[phone] • [phone]

Parts Ordering 1 800 304 2836

Fax [phone]

www.bushhog.com