Bush HOG 3210, HOG 3214, HOG 3209 User Manual

Page 1
LAND MAINTENANCE
REPAIR PARTS MANUAL
MODEL: 3200 SERIES
3209, 3210, 3214
SECTION: 46
BUSH HOG
®
(334) 872 6261 • (334) 874 2700
Parts Ordering 1 800 304 2836
Fax 1 800 572 1784
www.bushhog.com
Page 2
BUSH HOG/ LAND MAINTENANCE REPAIR PARTS MANUAL
3209, 3210, 3214
Serial Numbers 12-09999 and Below
ALPHABETICAL INDEX
CONTENTS PAGE
Axle Weldment 3209...........................................................46-1-1
3209 Offset .................................................................46-1-2
3210............................................................................46-1-3
3210 Offset .................................................................46-1-4
3214............................................................................46-1-5
Axle Arms (Pull Models) .....................................................46-7-1
Band, Rear (All Models)......................................................46-3-2
Belting, Front (Center Hitch Models) .................................46-3-2
Belting, Rear 3214..............................................................46-3-3
Base Assemblies 3209 .......................................................46-1-1
3209 Offset .................................................................46-1-2
3210............................................................................46-1-3
3210 Offset .................................................................46-1-4
3214............................................................................46-1-5
Blades & Blade Holders 3209, 3210...................................46-2-1
3209 Offset, 3210 Offset.............................................46-2-2
3214............................................................................46-2-3
Chain, Safety Tow ..............................................................46-6-1
Chains, Highway (All Models).............................................46-3-1
Clevis, Tongue....................................................................46-6-1
Cylinder, Hydraulic...........................................46-8-1 thru 46-8-3
Decals ........................................................See Base Assemblies
Deck Weldments........................................See Base Assemblies
Driveshafts Pull Models..............46-5-1, 46-5-2, 46-5-9, 46-5-13,
...............................................46-5-22 thru 46-5-27, 46-5-29
Lift & Semi-Mount.........................................46-5-3, 46-5-11
Jackshaft (All Pull Models) ...........................46-5-4, 46-5-12
Cross Shafts (3209, 3210)..........................................46-5-5
Cross Shafts (3209 Offset, 3210 Offset).....................46-5-6
Cross Shafts(3214)............46-5-6, 46-5-7, 46-5-12, 46-5-28
Gearbox, Assemblies.....................................46-4-1 thru 46-4-14
Hitches .............................................................46-6-1 thru 46-6-3
3 Pt. Lift ..........................................................46-6-2, 46-6-3
Semi-Mount ....................................................46-6-2, 46-6-3
Pull Type (Tongue) .....................................................46-6-1
Holder, Hose.......................................................................46-8-1
Hub, Wheel (Pull Models)...................................................46-7-1
Hub, Wheel (Lift & Semi-Mount).............................46-7-2, 46-7-3
Hydraulic Components....................................46-8-1 thru 46-8-3
Jackstand............................................................................46-6-1
Ratchet Assy.......................................................................46-8-2
Pillow Block Bearing & Mount.............................................46-5-8
Rims.................................................................46-7-2 thru 46-7-5
Shields, Safety..................................................................46-4-28
Shredder Attachment..........................................................46-2-4
Skids ..........................................................See Base Assemblies
Stop Kits (Hydraulic Cylinder).............................................46-8-1
Tailwheels 3 Pt. Lift & Semi-Mount 3214............................46-7-3
3 Pt. Lift & Semi-Mount 3209, 3210 ...............46-7-2, 46-7-3
Tires .................................................................46-7-2 thru 46-7-5
3209, 3210
Serial Numbers 12-10000 and Above
ALPHABETICAL INDEX
CONTENTS PAGE
Axle Weldment 3209 ...........................................................46-1-6
3209 Offset..................................................................46-1-7
3210 ............................................................................46-1-8
3210 Offset..................................................................46-1-9
Axle Arms (Pull Models)......................................................46-7-1
Band, Rear (All Models) ......................................................46-3-2
Belting, Front (Center Hitch Models)..................................46-3-2
Base Assemblies 3209R-1..................................................46-1-6
3209 Offset..................................................................46-1-7
3210 ............................................................................46-1-8
3210 Offset..................................................................46-1-9
Blades & Blade Holders 3209, 3210.......................46-1-6, 46-1-8
3209 Offset, 3210 Offset.................................46-1-7, 46-1-9
Chain, Safety Tow ..............................................................46-6-1
Chains, Highway (All Models) .............................................46-3-1
Clevis, Tongue ....................................................................46-6-1
Cylinder, Hydraulic............................................46-8-1 thru 46-8-3
Decals.........................................................See Base Assemblies
Deck Weldments.........................................See Base Assemblies
Driveshafts Pull Models..........................46-5-9, 46-5-16, 46-5-17
..............................................................46-5-22 thru 46-5-27
Lift & Semi-Mount......................................................46-5-11
Jackshafts .................................................................46-5-18
Cross Shafts (3209, 3210)..........................46-5-14, 46-5-15
..............................................................46-5-19 thru 46-5-21
Gearbox, Assemblies..............................46-4-15 through 46-4-27
Hitches........................................................46-6-1 through 46-6-2
3 Pt. Lift .......................................................................46-6-2
Semi-Mount.................................................................46-6-2
Pull Type (Tongue)......................................................46-6-1
Holder, Hose .......................................................................46-8-1
Hub, Wheel (Pull Models)....................................................46-7-1
Hub, Wheel (Lift & Semi-Mount) .............................46-7-2, 46-7-3
Hydraulic Components ....................................46-8-1 thru 46-8-3
Jackstand............................................................................46-6-1
Ratchet Assy. ......................................................................46-8-2
Pillow Block Bearing & Mount .............................................46-5-8
Rims .................................................................46-7-2 thru 46-7-5
Shields, Safety....................................................46-4-29, 46-4-30
Shredder Attachment ..........................................................46-2-4
Skids...........................................................See Base Assemblies
Stop Kits (Hydraulic Cylinder) .............................................46-8-1
Tailwheels, 3 Pt. Lift & Semi-Mount 3209, 3210 .................46-7-3
Tires..................................................................46-7-2 thru 46-7-5
SEPTEMBER, 2011
Page 3
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
REF. PART
NO. NO.
QTY. DESCRIPTION
1 N/A 1 Axle Weldment 2 90108BH 2 Bushing 3 44250BH 2 Capscrew 1” x 10 1/2” Gr. 8 4 15821 2 Lockwasher 1” 5 19502 2 Hex Nut 1” 6 90610 3 Reinforcing Pad 7 –––– 18 Capscrew 5/8” x 2 1/2” Gr. 8 8 –––– 18 Flanged Hex Nut 5/8”
9 50040394 1 L.H. Skid 10 50040393 1 R.H. Skid 11 50040391 2 Skid 12 44928BH 10 Plow Bolt 3/8” x 1-1/2” 13 –––– 10 Lockwasher 3/8” 14 –––– 10 Flatwasher 3/8” 15 –––– 10 Hex Nut 3/8” 16 N/A 1 Deck w/Decals 540 RPM
N/A 1 Deck w/Decals 1000 RPM 90462 1 Decal Kit 540 RPM 90463 1 Decal Kit 1000 RPM
17 50061049 2 Bush Hog Decals 18 90109 1 Model Decal 19 69878 1 Blade Rotation Decal (CCW) 20 69877 1 Blade Rotation Decal (CW) 21 50042072 1 Safety Decal Kit 22 50031214 2 Red Reflector 23 50031212 1 Amber Decal
3209 BASE AND RELATED PARTS
Serial Numbers 12-09999 and Below
46-1-1
1
2
3
4
5
6
7
8
10
9
11
12
13
14
15
16
12
13
14
15
22
18
20
19
22
23
21
21
17
SEPTEMBER, 2011
Page 4
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
REF. PART
NO. NO.
QTY. DESCRIPTION
1 50031472 1 Axle Weldment w/ Reflectors 2 90108BH 2 Bushing 3 44250BH 2 Capscrew 1” x 10 1/2” Gr. 8 4 15821 2 Lockwasher 1” 5 19502 2 Hex Nut 1” 6 90610 3 Reinforcing Pad 7 –––– 18 Capscrew 5/8” x 2 1/2” Gr. 8 8 –––– 18 Flanged Hex Nut 5/8”
9 50040394 1 L.H. Skid 10 50040393 1 R.H. Skid 11 50040391 2 Skid 12 44928BH 10 Plow Bolt 3/8” x 1-1/2” 13 –––– 10 Lockwasher 3/8” 14 –––– 10 Flatwasher 3/8” 15 –––– 10 Hex Nut 3/8” 16 N/A 1 Deck w/Decals 540 RPM
90535 1 Decal Kit 540 RPM 17 50061049 2 Bush Hog Decals 18 90109 1 Model Decal 19 69878 2 Blade Rotation Decal (CCW) 20 50042072 1 Safety Decal Kit 21 50031214 4 Red Reflector 22 50031212 2 Amber Reflector 23 50031219 3 Red/Orange Reflector
3209 OFFSET BASE AND RELATED PARTS
Serial Numbers 12-09999 and Below
46-1-2
1
2
3
4
5
6
7
8
9
10
11
12
12
13
13
14
15
14
15
16
18
17
19
19
20
21
21
23
23
23
21
21
22
22
SEPTEMBER, 2011
Page 5
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
REF. PART
NO. NO.
QTY. DESCRIPTION
1 97200 1 Axle Weldment 2 90108BH 2 Bushing 3 44250BH 2 Capscrew 1” x 10 1/2” Gr. 8 4 15821 2 Lockwasher 1” 5 19502 2 Hex Nut 1” 6 90610 3 Reinforcing Pad 7 –––– 18 Capscrew 5/8” x 2 1/2” Gr. 8 8 –––– 18 Flanged Hex Nut 5/8”
9 50040394 1 L.H. Skid 10 50040393 1 R.H. Skid 11 50040391 2 Skid 12 44928BH 10 Plow Bolt 3/8” x 1-1/2” 13 –––– 10 Lockwasher 3/8” 14 –––– 10 Flatwasher 3/8” 15 –––– 10 Hex Nut 3/8” 16 N/A 1 Deck w/Decals 540 RPM
N/A 1 Deck w/Decals 1000 RPM 90441 1 Decal Kit 540 RPM 90442 1 Decal Kit 1000 RPM
17 50061049 2 Bush Hog Decals 18 90156 1 Model Decal, 3210
50067801 1 Model Decal, 13210 19 69878 1 Blade Rotation Decal (CCW) 20 69877 1 Blade Rotation Decal (CW) 21 50042072 1 Safety Decal Kit 22 50031214 2 Red Reflector 23 50031212 2 Amber Decal
3210 BASE AND RELATED PARTS
Serial Numbers 12-09999 and Below
46-1-3
12
14
13
15
23
18
22
5
4
2
3
1
8
6
7
16
22
23
21
15
13
14
12
11
17
10
20
19
9
SEPTEMBER, 2011
Page 6
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
REF. PART
NO. NO.
QTY. DESCRIPTION
1 50031299 1 Axle Weldment w/ Decals 2 90108BH 2 Bushing 3 44250BH 2 Capscrew 1” x 10 1/2” Gr. 8 4 15821 2 Lockwasher 1” 5 19502 2 Hex Nut 1” 6 90610 3 Reinforcing Pad 7 –––– 18 Capscrew 5/8” x 2 1/2” Gr. 8 8 –––– 18 Flanged Hex Nut 5/8”
9 50040394 1 L.H. Skid 10 50040393 1 R.H. Skid 11 50040391 2 Skid 12 44928BH 10 Plow Bolt 3/8” x 1-1/2” 13 –––– 10 Lockwasher 3/8” 14 –––– 10 Flatwasher 3/8” 15 –––– 10 Hex Nut 3/8” 16 N/A 1 Deck w/Decals 540 RPM
90428 1 Decal Kit 540 RPM 17 50061049 2 Bush Hog Decals 18 90109 1 Model Decal 19 69878 2 Blade Rotation Decal (CCW) 20 50042072 1 Safety Decal Kit 21 50031214 4 Red Reflector 22 50031212 2 Amber Reflector 23 50031219 3 Red/Orange Fluorescent Tape
3210 OFFSET BASE AND RELATED PARTS
Serial Numbers 12-09999 and Below
46-1-4
12
131415
9
24
20
22
21
18
19
5
4
2
3
1
23
23
23
21
21
21
22
19
8
6
7
15
13
14
12
11
17
10
16
SEPTEMBER, 2011
Page 7
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
REF. PART
NO. NO.
QTY. DESCRIPTION
1 N/A 1 Axle Weldment w/ Decals 2 90108BH 4 Bushing 3 44250BH 2 Capscrew 1” x 10 1/2” Gr. 8 4 15821 2 Lockwasher 1” 5 19502 2 Hex Nut 1” 6 90610 3 Reinforcing Pad 7 –––– 18 Capscrew 5/8” x 2 1/2” Gr. 8 8 –––– 18 Flanged Hex Nut 5/8”
9 50040394 1 L.H. Skid 10 50040393 1 R.H. Skid 11 50040391 2 Skid 12 44928BH 10 Plow Bolt 3/8” x 1-1/2” 13 –––– 10 Lockwasher 3/8” 14 –––– 10 Flatwasher 3/8” 15 –––– 10 Hex Nut 3/8” 16 N/A 1 Deck w/Decals 540 RPM
N/A 1 Deck w/Decals 1000 RPM N/A 1 Decal Kit 540 RPM N/A 1 Decal Kit 1000 RPM
REF. PART
NO. NO.
QTY. DESCRIPTION
17 50061049 2 Bush Hog Decals 18 90229 1 Model Decal 19 69878 2 Blade Rotation Decal (CCW) 20 69877 1 Blade Rotation Decal (CW) 21 50042072 1 Safety Decal Kit 22 50031214 7 Red Reflector 23 50031212 2 Amber Decal 24 90223 1 Baffle L.H. 25 90224BH 1 Baffle R.H. 26 –––– 12 Capscrew 1/2” x 1 1/4” Gr.5 27 –––– 12 Flatwasher 1/2” 28 –––– 12 Lockwasher 1/2” 29 –––– 12 Hex Nut 1/2” 30 50031219 5 Red / Orange Reflector
3214 BASE AND RELATED PARTS
46-1-5
1
30
22
2
3
4
5
6
7
8
9
10
11
12
13
15
14
12
13
14
15
16
17
18
19
19
20
21
21
23
22
23
22
24
28
29
27
26
25
30
22
30
22
22
30
22
30
SEPTEMBER, 2011
Page 8
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-1-6
3209 BASE ASSEMBLY
Serial Numbers 12-10000 and Above
With Omni Gearboxes
REF. PART
NO. NO.
QTY. DESCRIPTION
1 50018405 1 Deck w/Decals 540 RPM
50018404 1 Deck w/Decals 1000 RPM
90462 1 Decal Kit 540 RPM
90463 1 Decal Kit 1000 RPM 2 50017838 1 Axle Weldment 3 50018291 2 Bushing 4 20100 2 Capscrew 1” x 9 1/2” Gr. 5 5 15821 4 Lockwasher 1” 6 19502 4 Hex Nut 1” 7 50018280 3 Reinforcing Pad 8 –––– 12 Capscrew 3/4” x 2 1/2”
–––– 6 Capscrew 3/4” x 2-3/4” (Center)
9 –––– 18 Hex Nut 3/4” Gr.G
10 50040394 1 L.H. Skid 11 50040393 1 R.H. Skid 12 50040391 2 Skid, Removable 13 44928BH 10 Plow Bolt 3/8” x 1-1/2” 14 –––– 10 Lockwasher 3/8” 15 –––– 10 Flatwasher 3/8” 16 –––– 10 Hex Nut 3/8” 17 50061049 2 Bush Hog Decal 18 90109 1 Model Decal 19 69878 1 Blade Rotation Decal (CCW) 20 69877 1 Blade Rotation Decal (CW)
REF. PART
NO. NO.
QTY. DESCRIPTION
21 50029417 1 Sheet Decal, 540 RPM
50029418 1 Sheet Decal, 1000 RPM 22 50029419 1 Sheet Decal 23 50057117 1 Blade Pan 24 7829 2 Blade, CW Rotation 25 7828 2 Blade, CCW Rotation 26 50031214 2 Red Reflector 27 50031212 1 Amber Reflector 28 63607 2 Blade Bolt Kit 29 252BH 2 Blade Nut 1-1/8” 30 20322 2 Lockwasher 1-1/8” 31 7919BH 2 Blade Bolt 32 50057320 2 Blade Bar
1
13
11
23
23
15 14 16
20
2
4
18
26
8
19
22
21
27
26
13
12
17
10
32
16 14 15
9
7
6
5
3
29
30
31
28
24
31
29
30
25
28
SEPTEMBER, 2011
Page 9
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-1-7
3209 OFFSET BASE ASSEMBLY
Serial Numbers 12-10000 and Above
With Omni Gearboxes
REF. PART
NO. NO.
QTY. DESCRIPTION
1 N/A 1 Deck w/Decals, 540 RPM
90535 1 Decal Kit, 540 RPM 2 50031472 1 Axle Weldment w/ Decals 3 90108BH 2 Bushing 4 20187 2 Capscrew 1” x 10” Gr. 5 5 15821 4 Lockwasher 1” 6 19502 4 Hex Nut 1” 7 50018280 2 Reinforcing Pad 8 –––– 6 Capscrew 3/4” x 2 1/2” Gr. 5 9 –––– 12 Hex Nut 3/4” Gr.G
10 50040394 1 L.H. Skid 11 50040393 1 R.H. Skid 12 50040391 2 Skid, Removable 13 44928BH 10 Plow Bolt 3/8” x 1-1/2” 14 –––– 10 Lockwasher 3/8” 15 –––– 10 Flatwasher 3/8” 16 –––– 10 Hex Nut 3/8” 17 50061049 2 Bush Hog Decal 18 90109 1 Model Decal
REF. PART
NO. NO. QTY. DESCRIPTION
19 69878 2 Blade Rotation Decal (CCW) 20 50031214 4 Red Reflector 21 50031212 2 Amber Decal 22 63607 2 Blade Bolt Kit 23 252BH 2 Blade Nut 1-1/8” 24 20322 2 Lockwasher 1-1/8” 25 7919BH 2 Blade Bolt 26 50057117 1 Blade Pan 27 7828 4 Blade, CCW Rotation 28 –––– 6 Capscrew 3/4” x 2-3/4” 29 50029417 1 Sheet Decal, 540 RPM
50029418 1 Sheet Decal, 1000 RPM 30 50029419 1 Sheet Decal 31 50031219 3 Red/Orange Fluorescent Tape 32 50031473 1 Amber Reflector 33 50057320 2 Blade Bar
1
13
11
26
15 14 16
19
28
2
4
31
31
31
20
20
18
21
20
8
7
7
19
30
29
32
21
20
13
12
17
10
33
16 14 15
9
9
6
5
3
25
23
24
27
22
26
23
24
25
22
27
SEPTEMBER, 2011
Page 10
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
3210 BASE ASSEMBLY
Serial Numbers 12-10000 and Above
With Omni Gearboxes
REF. PART
NO. NO.
QTY. DESCRIPTION
1 50018427 1 Deck w/Decals 540 RPM
50018426 1 Deck w/Decals 1000 RPM
90441 1 Decal Kit 540 RPM
90442 1 Decal Kit 1000 RPM 2 97200 1 Axle Weldment 3 90108 2 Bushing 4 44250BH 2 Capscrew 1” x 10-1/2” Gr. 5 5 15821 4 Lockwasher 1” 6 19502 4 Hex Nut 1” 7 50018280 3 Reinforcing Pad 8 –––– 12 Capscrew 3/4” x 2 1/2” 9 –––– 18 Hex Nut 3/4” Gr.G
10 50040394 1 L.H. Skid 11 50040393 1 R.H. Skid 12 50040391 2 Skid, Removable 13 44928BH 10 Plow Bolt 3/8” x 1-1/2” 14 –––– 10 Lockwasher 3/8” 15 –––– 10 Flatwasher 3/8” 16 –––– 10 Hex Nut 3/8” 17 50061049 2 Bush Hog Decal 18 90156 1 Model Decal, 3210
50067801 1 Model Decal, 13210
19 D551 1 Blade Rotation Decal (CCW)
REF. PART
NO. NO.
QTY. DESCRIPTION
20 D552 1 Blade Rotation Decal (CW) 21 50031214 2 Red Reflector 22 50031212 2 Amber Reflector 23 63607 2 Blade Bolt Kit 24 252BH 2 Blade Nut 1-1/8” 25 20322 2 Lockwasher 1-1/8” 26 7919BH 2 Blade Bolt 27 50057117 1 Blade Pan 28 90014BH 2 Blade, CW Rotation 29 90015 2 Blade, CCW Rotation 30 D549 1 Sheet Decal 31 D553 1 Warning Decal 32 –––– 6 Capscrew 3/4” x 2-3/4” (Center) 33 50057320 2 Blade Bar 34 D559 1 Genuine Parts Decal 35 D614 3 Danger Decal 36 D546 1 Danger Decal 37 D547 1 Danger Decal 38 D581 1 Lube Decal 39 D454 1 Warning Decal 40 D548 1 Warning Decal
1
13
11
27
27
15 14 16
20
2
4
18
21
8
32
19
31
30
22
21
13
12
17
10
33
16 14 15
9
9
7
7
6
5
3
24
25
26
23
28
26
24
25
29
23
46-1-8
22
35
38
36
37
40
35
35
34
39
(Overlay onto item 37 on 1000 rpm only)
3210 BASE ASSEMBLY
With B & P Gearboxes
SEPTEMBER, 2011
Page 11
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
SEPTEMBER, 2011
31
21
13
23
15 14 16
11
25
26
33
20
24
34
29
22
21
18
9
30
1
27
32
27
20
7
28
36
24
19
25
36
35
23
4
5
6
3
8
34
10
2
31
21
34
37
19
7
22
17
12
21
16 14 15
13
9
31
3210 OFFSET BASE ASSEMBLY
Serial Numbers 12-10000 and Above
With Omni Gearboxes
3210 OFFSET BASE ASSEMBLY
With B & P Gearboxes
REF. PART
NO. NO.
1 50018516 1 Deck w/Decals 540 RPM
90428 1 Decal Kit 540 RPM 2 50031299 1 Axle Weldment w/ Decals 3 90108 2 Bushing 4 20187 2 Capscrew 1” x 10” Gr. 5 5 15821 4 Lockwasher 1” 6 19502 4 Hex Nut 1” 7 50018280 2 Reinforcing Pad 8 –––– 6 Capscrew 3/4” x 2 1/2” Gr. 5 9 20299 12 Locknut 3/4” Gr.G
10 50040394 1 L.H. Skid 11 50040393 1 R.H. Skid 12 50040391 2 Skid, Removable 13 44928BH 10 Plow Bolt 3/8” x 1-1/2” 14 –––– 10 Lockwasher 3/8” 15 –––– 10 Flatwasher 3/8” 16 –––– 10 Hex Nut 3/8”
QTY. DESCRIPTION
26
REF. PART
NO. NO.
17 50061049 2 Bush Hog Decal 18 90156 1 Model Decal 19 D551 2 Blade Rotation Decal (CCW) 20 90015 4 Blade, CCW Rotation 21 50031214 4 Red Reflector 22 50031212 2 Amber Reflector 23 63607 2 Blade Bolt Kit 24 252BH 2 Blade Nut 1-1/8” 25 20322 2 Lockwasher 1-1/8” 26 7919BH 2 Blade Bolt 27 50057117 1 Blade Pan 28 –––– 6 Capscrew 3/4” x 2-3/4” 29 D549 1 Sheet Decal, 540 RPM 30 D553 1 Warning Decal 31 50031219 3 Red/Orange Fluorescent Tape 32 50057320 2 Blade Bar 33 D581 1 Lube Decal 34 D614 3 Danger Decal 35 D546 1 Danger Decal 36 D547 1 Danger Decal 37 D559 1 Genuine Parts Decal 38 D454 1 Warning Decal
QTY. DESCRIPTION
46-1-9
Page 12
Page 13
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
REF. PART
NO. NO.
QTY. DESCRIPTION
1 63607 2 Blade Bolt Kit 2 252BH 2 Blade Nut 1 1/8” 3 20322 2 Lockwasher 1 1/8” 4 7919BH 2 Blade Bolt 5 66501 1 Blade Pan 6 7829 2 Blade CW Rotation (3209)
90014BH 2 Blade CW Rotation (3210)
7 7828 2 Blade CCW Rotation (3209)
90015 2 Blade CCW Rotation (3210)
BLADES AND BLADE HOLDERS
For 3209 & 3210 Center Hitch Models
Serial Numbers 12-09999 and Below
2
3
4
1
6
5
5
7
2
3
1
4
46-2-1
SEPTEMBER, 2011
Page 14
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
REF. PART
NO. NO.
QTY. DESCRIPTION
1 63607 2 Blade Bolt Kit 2 252BH 2 Blade Nut 1 1/8” 3 20322 2 Lockwasher 1 1/8” 4 7919BH 2 Blade Bolt 5 66501 1 Blade Pan 6 7828 4 Blade CCW Rotation (3209)
90015 4 Blade CCW Rotation (3210)
BLADES AND BLADE HOLDERS
For 3209 & 3210 Offset Hitch Models Serial Numbers 12-09999 and Below
46-2-2
1
2
3
4
6
5
6
5
1
2
3
4
SEPTEMBER, 2011
Page 15
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
REF. PART
NO. NO.
QTY. DESCRIPTION
1 63607 6 Blade Bolt Kit 2 252BH 6 Jamnut 1 1/8” 3 20322 6 Lockwasher 1 1/8” 4 7919BH 6 Blade Bolt 5 86665 2 Blade, Clockwise Rotation (540 RPM)
4 Blade, Clockwise Rotation (1000 RPM)
6 86664 4 Blade, Counter Clockwise Rotation (540 RPM)
2 Blade, Counter Clockwise Rotation (1000 RPM) 7 66501 3 Round Pan Weldment 8 90689 3 Straight Bar Weldment
46-2-3
2
3
4
1
6
7
8
5
Right Side Counter Clockwise
Left Side Clockwise
Center Counter Clockwise 540 RPM (Shown) Clockwise 1000 RPM (Not Shown)
BLADES AND BLADE HOLDERS
For All 3214 Models
SEPTEMBER, 2011
Page 16
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-2-4
REF. PART QTY.
NO. NO. 30” SPACING 38”/40” SPACING DESCRIPTION
1 90538 1 1 “V” Baffle 2 60032BH 5 5 Stationary Blade 3 84345 5 3 Blade Mount 4 84342 5 3 Support Plate 5 86666 6 6 Double Edge Blade 6 90563 –––– 1 Mount Weldment 7 90537 –––– 1 Baffle, Front R.H. (540 RPM)
90536 –––– 1 Baffle, Front L.H. (1000 RPM)
8 84667 –––– 1 Support
*9 86310 6 6 Pivot Bushing *10 90612 6 6 Blade Bolt *11 44383BH 6 6 Slotted Nut 1-1/8” *12 15473 6 6 Cotter Pin 1/4” x 2-1/2”
13 20294 6 6 Capscrew 5/8” x 6-1/2” Gr.5 14 9162000 10 10 Locknut 5/8” 15 –––– 8 7 Capscrew 1/2” x 1-3/4” Gr.5 16 –––– 21 14 Flatwasher 1/2” 17 –––– 8 7 Lockwasher 1/2” 18 –––– 8 8 Hex Nut 1/2” 19 –––– –––– 2 Capscrew 5/8” x 2” Gr.5 20 –––– –––– 2 Capscrew 5/8” x 2-1/2” Gr.5 21 –––– –––– 10 Lockwasher 5/8” 22 90689 3 3 Blade Holder
*Note: Order 90613 for blade bolt kit. Kit includes parts for 1 blade bar assembly.
SHREDDER ATTACHMENT
30” & 38/ 40” ROW SPACING
For All 3214 Straight Blade Bar Models
3
2
20
20
19
13
5
10
See Blades & Blade Holders page for these part no’s.
10
9
9
12
12
17 18
16 17 18
14 21 4
7
13
2
3
11
22
11
14
14
21
21
4
14 16
15 16
8
14 21 4
13
6
2
2
3
1
SEPTEMBER, 2011
Page 17
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-3-1
REF. PART
NO. NO.
QTY. DESCRIPTION
1 50020295 1 Front Assy., Single Row, 3209
50020294 1 Front Assy., Double Row 3209 50020288 1 Front Assy., L.H. Single Row 3210 50020287 1 Front Assy., R.H. Single Row 3210 50020289 1 Front Assy., L.H. Double Row 3210 50020290 1 Front Assy., R.H. Double Row 3210 50020277 1 Front Assy., L.H. Single Row 3214 50020276 1 Front Assy., R.H. Single Row 3214
2 50020292 1 Rear Assy., Center Single Row 3209
50020293 1 Rear Assy., Center Double Row 3209 50020285 1 Rear Assy., Center Single Row 3210 50020284 1 Rear Assy., Center Double Row 3210 50020272 1 Rear Assy., Center Single Row 3214
3 50020301 1 Rear Assy., R.H. Single Row 3209
50020297 1 Rear Assy., R.H. Double Row 3209 50020280 1 Rear Assy., R.H. Single Row 3210 50020281 1 Rear Assy., R.H. Double Row 3210 50020274 1 Rear Assy., R.H. Single Row 3214
4 50020300 1 Rear Assy., L.H. Single Row 3209
50020298 1 Rear Assy., L.H. Double Row 3209 50020279 1 Rear Assy., L.H. Single Row 3210 50020282 1 Rear Assy., L.H. Double Row 3210
50020273 1 Rear Assy., L.H. Single Row 3214 5 —— A/R Capscrew 1/2” x 1-1/4” Gr. 5 6 —— A/R Flatwasher 1/2” 7 —— A/R Lockwasher 1/2” 8 —— A/R Hex Nut 1/2” 9 —— A/R Capscrew 1/2” x 4-1/2” Gr. 5
10 90546 1 Bracket, Front, Single Row, 3209
90097 1 Bracket, Front, Double Row, 3209 90547 1 Bracket, Front L.H., Single Row, 3210 90548 1 Bracket, Front R.H., Single Row, 3210
REF. PART
NO. NO.
QTY. DESCRIPTION
90238 1 Bracket, Front L.H., Double Row, 3210 90239 1 Bracket, Front R.H., Double Row, 3210 90205 1 Bracket, Front L.H., Single Row, 3214 90206 1 Bracket, Front R.H., Single Row, 3214
11 50020296 1 Rod, Front, 3209
50020286 2 Rod, Front, 3210 50020275 2 Rod, Front, 3214
12 50020291 1 Rod, Center Rear, 3209
50020283 1 Rod, Center Rear, 3210 50020271 1 Rod, Center Rear, 3214
13 50020299 2 Rod, Rear Side, 3209
50020278 2 Rod, Rear Side, 3210, 3214
14 90545 1 Bracket, Rear Center, Single Row, 3209
90091 1 Bracket, Rear Center, Double Row, 3209 90553 1 Bracket, Rear Center, Single Row, 3210
90152BH 1 Bracket, Rear Center, Double Row, 3210
90221 1 Bracket, Rear Center, Single Row, 3214
15 91417 1 Bracket, Rear R.H., Single Row, 3209
91423 1 Bracket, Rear R.H., Double Row, 3209 91429 1 Bracket, Rear R.H., Single Row, 3210 91435 1 Bracket, Rear R.H., Double Row, 3210
91441BH 1 Bracket, Rear R.H., Single Row, 3214
16 91424 1 Bracket, Rear L.H., Double Row, 3209
91418 1 Bracket, Rear L.H., Single Row, 3209 91430 1 Bracket, Rear L.H., Single Row, 3210 91436 1 Bracket, Rear L.H., Double Row, 3210
91442 1 Bracket, Rear L.H., Single Row, 3214 17 50017211 A/R Chain, 6 Link, Plated 18 –––– A/R Capscrew 5/16” x 2” Gr.5 19 –––– A/R Flatwasher 5/16” 20 –––– A/R Locknut 5/16” 21 50017210 A/R Spiral Pin .125” x 1.25”
3200 SERIES CHAINS
21
3
17
13
15
21
10
1
11
17
18 19 19 20
21
14
2
13
21
16
20
19
19
18
21
8 7
6 9
21
17
4
12
7 8
5 6
SEPTEMBER, 2011
Page 18
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-3-2
REF. PART
NO. NO.
QTY. DESCRIPTION
1 —— A/R Lockwasher 1/2” 2 —— A/R Flatwasher 1/2” 3 —— A/R Capscrew 1/2” x 4-1/2” Gr. 5 4 —— A/R Hex Nut 1/2” 5 90503 1 Front Belting Assy. 3209
90459 1 Front Belting Assy. 3210 90472 1 Front Belting Assy. 3214
6 90323 1 Belting 3209
90324 1 Belting 3210 90325 1 Belting 3214
7 90329 1 Cover 3209
90327 1 Cover 3210
*90343 2 Cover 3214
8 90328 1 Bracket 3209
90326 1 Bracket 3210 *90342 1 R.H. Bracket 3214 *90341 1 L.H. Bracket 3214
9 —— A/R Capscrew 5/16” x 1-1/4” Gr. 5
FRONT BELTING AND REAR BANDS
For 3200 Series
REF. PART
NO. NO.
QTY. DESCRIPTION
10 —— A/R Flatwasher 5/16” 11 —— A/R Lockwasher 5/16” 12 —— A/R Hex Nut 5/16” 13 —— 2 Capscrew 5/16” x 2-1/2” Gr. 5 14 50017212 4 Chain, 7 Link 15 9161000 2 Locknut 5/16” 16 90095 1 Rear Band 3209
90131 1 Rear Band 3210 90291 1 Rear Band 3214
17 90094 1 R.H. Rear Band 3209
90192 1 R.H. Rear Band 3210 90293 1 R.H. Rear Band 3214
18 90093 1 L.H. Rear Band 3209
90191BH 1 L.H. Rear Band 3210
90292 1 L.H. Rear Band 3214
19 —— A/R Capscrew 1/2” x 1-1/4” Gr. 5
—— 11 Capscrew 1/2” x 4-1/2” Gr. 5
used on Center Band, 3214 Models
17
16
19
2
18
1
4
15
13
8
14
6
7
5
12
11
10
9
4
1
2
3
SEPTEMBER, 2011
Page 19
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
REF. PART
NO. NO.
QTY. DESCRIPTION
1 —— 10 Capscrew 1/2” x 1-1/2” Gr. 5 2 —— 21 Lockwasher 1/2” 3 —— 23 Flatwasher 1/2” 4 —— 11 Capscrew 1/2” x 4-1/2” Gr. 5 5 —— 21 Hex Nut 1/2” 6 90576 1 Center Rear Belting Assy. 7 —— 27 Capscrew 5/16” x 1-1/4” Gr. 5 8 —— 27 Hex Nut 5/16”
9 —— 27 Lockwasher 5/16” 10 —— 54 Flatwasher 5/16” 11 90567 1 Rear Center Bracket 12 90570 1 Rear Center Belting 13 90572 1 Rear Center Cover 14 90586 1 R.H. Rear Belting Assy. 15 90571 2 Short Rear Belting 16 90573 2 Short Rear Cover 17 90574 1 R.H. Bracket Weld. 18 90587 1 L.H. Rear Belting Assy. 19 90575 1 L.H. Bracket Weld.
REAR BELTING BUNDLE
FOR MODELS 3214, 13214
WITH SHREDDER ATTACHMENT
46-3-3
17
15
16
14
1
3
2
5
4
3
5
2
3
6
11
12
13
8
9
10
10
7
18
19
15
16
SEPTEMBER, 2011
Page 20
Page 21
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-1
REF. PART
NO. NO.
QTY. DESCRIPTION
1 70578 1 Housing, Top 2 70479 1 Housing, Lower 3 70469 1 Cover, Left 4 70468 1 Cover, Right 5 70582 1 Shaft, Input 1-3/4” 6 70466 1 Shaft Output 1-3/8” 7 70577 1 Crown Gear 15 Teeth 8 70581 1 Pinion Gear 19 Teeth
9 70797 1 Bearing 10 70801 1 Bearing 11 70800 2 Bearing 12 70462BH 12 Hex Bolt M10 x 22 13 70891 8 Bolt M10 x 25 14 70399 1 Locknut, M40 x 1.5 15 70398 1 Spring Washer 16 70304 2 Spring Pin 17 70393 1 Plug 18 70463 1 Oil Seal 35 x 56 x 8 19 70575 1 Oil Seal 50 x 90 x 10 20 70329 A/R Shim .3mm
70330 A/R Shim .4mm 70331 A/R Shim .5mm
70332BH A/R Shim 1.3mm
21 70344 A/R Shim .3mm
70345BH A/R Shim .5mm 70346BH A/R Shim 1.0mm
70347 A/R Shim .4mm 22 70546 1 Vent Plug 23 70580 1 Spacer
70825 1000 RPM
CENTER GEARBOX
Used on Models 13209 & 13210
Serial Numbers 12-09999 and Below
Replaced by 70982 Gearbox Assembly
17
22
21 11
1
SEPTEMBER, 2011
Page 22
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-2
REF. PART
NO. NO.
QTY. DESCRIPTION
70982 1 Gearbox Assy
1 70987 1 Housing, Top 2 70479 1 Housing, Lower 3 70469 1 Cover, Left 4 70468 1 Cover, Right 5 70988 1 Shaft, Input 1-3/4” 6 70466 1 Shaft Output 1-3/8” 7 70577 1 Crown Gear 15 Teeth 8 70581 1 Pinion Gear 19 Teeth
9 70797 1 Bearing 10 70801 1 Bearing 11 70800 1 Bearing 12 44153BH 12 Hex Bolt M10 x 22 13 70891 8 Bolt M10 x 25 14 70586 1 Locknut, M40 x 1.5 15 70585 1 Cotter Pin 16 70304 2 Spring Pin 17 70393 1 Plug 18 70463 1 Oil Seal 35 x 56 x 8 19 70575 1 Oil Seal 50 x 90 x 10 20 70329 A/R Shim .3mm
70330 A/R Shim .4mm 70331 A/R Shim .5mm
70332BH A/R Shim 1.3mm
21 70348 A/R Shim .3mm
70349BH A/R Shim .4mm
70350 A/R Shim .5mm
70351 A/R Shim 1.0mm 22 70546 1 Vent Plug 23 70940 1 Bearing
70982 1000 RPM
CENTER GEARBOX
Used on Models 13209 & 13210
Serial Numbers 12-09999 and Below
1
SEPTEMBER, 2011
Page 23
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-3
REF. PART
NO. NO.
QTY. DESCRIPTION
1 70578 1 Housing, Top 2 70479 1 Housing, Lower 3 70469 1 Cover, Left 4 70468 1 Cover, Right 5 70582 1 Shaft, Input 1-3/4” 6 70466 1 Shaft Output 1-3/8” 7 70473 1 Crown Gear 28 Teeth 8 70465 1 Pinon Gear 15 Teeth
9 70797 1 Bearing 10 70801 1 Bearing 11 70800 2 Bearing 12 70462BH 12 Hex Bolt M10 x 22 13 70302 8 Screw, Allen Head M10 x 25 14 70399 1 Locknut, M40 x 1.5 15 70398 1 Spring Washer 16 70304 2 Spring Pin 17 70393 1 Plug 18 70463 1 Oil Seal 35 x 56 x 8 19 70575 1 Oil Seal 50 x 90 x 10 20 70329 A/R Shim .3mm
70330 A/R Shim .4mm 70331 A/R Shim .5mm
70332BH A/R Shim 1.3mm
21 70344 A/R Shim .3mm
70345BH A/R Shim .5mm 70346BH A/R Shim 1.0mm
70347 A/R Shim .4mm 22 70546 1 Vent Plug 23 70581 1 Spacer
70594 CENTER GEARBOX ASSY.
540 RPM
Used on Models 3209 & 3210
Serial Numbers 12-09999 and Below
Replaced by 70980 Gearbox Assembly
17
22
21
11
1
SEPTEMBER, 2011
Page 24
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-4
REF. PART
NO. NO.
QTY. DESCRIPTION
70980 1 Gearbox Assy
1 70987 1 Housing, Top 2 70479 1 Housing, Lower 3 70469 1 Cover, Left 4 70468 1 Cover, Right 5 70988 1 Shaft, Input 1-3/4” 6 70466 1 Shaft Output 1-3/8” 7 70989 1 Crown Gear 28 Teeth 8 70465 1 Pinion Gear 15 Teeth
9 70797 1 Bearing 10 70801 1 Bearing 11 70800 1 Bearing 12 44153BH 12 Hex Bolt M10 x 22 13 70891 8 Bolt M10 x 25 14 70586 1 Locknut, M40 x 1.5 15 70585 1 Cotter Pin 16 70304 2 Spring Pin 17 70393 1 Plug 18 70463 1 Oil Seal 35 x 56 x 8 19 70575 1 Oil Seal 50 x 90 x 10 20 70329 A/R Shim .3mm
70330 A/R Shim .4mm 70331 A/R Shim .5mm
70332BH A/R Shim 1.3mm
21 70348 A/R Shim .3mm
70349BH A/R Shim .4mm
70350 A/R Shim .5mm
70351 A/R Shim 1.0mm 22 70546 1 Vent Plug 23 70940 1 Bearing
70980 CENTER GEARBOX
540 RPM
Used on Models 3209 & 3210
Serial Numbers 12-09999 and Below
1
SEPTEMBER, 2011
Page 25
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-5
REF. PART
NO. NO.
QTY. DESCRIPTION
1 70462BH 12 Capscrew M10 x 22 2 70463 1 Seal 35 x 56 x 8 3 70801 1 Bearing 4 70465 1 Pinon Gear (15 Teeth) 5 70466 1 Shaft 6 70797 1 Bearing 7 70578 1 Top Housing 8 70393 1 Plug
9 70468 1 Cover 10 70469 1 Cover 11 70546 1 Vent Plug 12 70802 1 Bearing 13 70579 1 Bottom Shaft 14 70304 2 Spring Pin 15 70472BH 1 Lower Housing 16 70302 8 Capscrew M10 x 25 17 70800 3 Bearing 18 70575 2 Dust Excluder 19 70166 1 Shoulder Ring 20 70077 1 Washer 21 70076 1 Castle Nut M30 x 2
REF. PART
NO. NO.
QTY. DESCRIPTION
22 15473 1 Cotter Pin 1/4 x 2-1/2” 23 70399 1 Locknut M40 x 1.5 24 70398 1 Washer, Spring 40 x 62 x 1.25 25 70473 1 Crown Gear (28 Teeth) 26 70582 1 Input Shaft (For 70550 Assy. Only) 27 70329 A/R Shim .3mm Thick
70330 A/R Shim .4mm Thick 70331 A/R Shim .5mm Thick
70332BH A/R Shim 1.0mm Thick
28 70337 A/R Shim .3mm Thick
70338 A/R Shim .4mm Thick 70339 A/R Shim .5mm Thick 70340 A/R Shim 1.0mm Thick
29 70344 A/R Shim .3mm Thick
70345BH A/R Shim .5mm Thick 70346BH A/R Shim 1.0mm Thick
70347 A/R Shim .4mm Thick 30 70580 1 Spacer (70550 Assy. Only) 31 70571 1 Cotter Pin B4 x 50 32 70570 1 Nut M30 x 1.5 33 70576 1 Protective Shield
70550 CENTER GEARBOX
ASSEMBLY (540 RPM)
Used on 3214 Models
Replaced by 70949 Gearbox Assembly
SEPTEMBER, 2011
Page 26
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-6
70549 CENTER GEARBOX ASSEMBLY
1000 RPM
Used on 13214
Replaced by 70981 Gearbox Assembly
REF. PART
NO. NO.
QTY. DESCRIPTION
1 70462BH 12 Hex Bolt M10 x 22 2 70463 2 Oil Seal 35 x 56 x 8 3 70801 1 Bearing 4 70329 A/R Shim .3mm Thick
70330 A/R Shim .4mm Thick 70331 A/R Shim .5mm Thick
70332BH A/R Shim 1.0mm Thick 5 70577 1 Crown Gear 19 Teeth 6 70466 1 Output Shaft 7 70797 1 Bearing 8 70578 1 Casing 9 70393 2 Plug
10 70468 1 Cover 11 70469 1 Cover 12 70570 1 Nut M30 x 1.5 13 70571 1 Cotter Pin B4 x 50 14 70337 A/R Shim .3mm Thick
70338 A/R Shim .4mm Thick 70339 A/R Shim .5mm Thick
70340 A/R Shim 1.0mm Thick 15 70802 1 Bearing 16 70579 1 Shaft 17 70304 2 Spring Pin 10 x 26 18 70472BH 1 Lower Housing 19 70302 8 Cheese Head Screw M10 x 25 20 70800 3 Bearing 21 70575 2 Dust Excluder
REF. PART
NO. NO.
QTY. DESCRIPTION
22 70166 1 Shoulder Ring 23 70077 1 Blank Washer 24 70076 1 Castle Nut M30 x 2 25 70580 1 Spacer 26 70399 1 Locknut M40 x 1.5 27 70398 1 Spring Washer 28 70581 1 Bevel Pinion 15 Teeth 29 70344 A/R Shim .3mm Thick
70345BH A/R Shim .5mm Thick 70346BH A/R Shim 1.0mm Thick
70347 A/R Shim .4mm Thick 30 70582 1 Input Shaft 1-3/4” 31 70583 1 Bevel Pinion 15 Teeth 32 70576 1 Protective Shield 33 15473 1 Cotter Pin 1/4 x 2-1/2” 34 70546 1 Vent Plug
SEPTEMBER, 2011
Page 27
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-7
70981 CENTER GEARBOX ASSEMBLY
1000 RPM
Used on 13214 Models
REF. PART
NO. NO.
QTY. DESCRIPTION
70981 1 Gearbox Assy
1 44153BH 12 Hex Bolt M10 x 22 2 70463 2 Oil Seal 35 x 56 x 8 3 70801 1 Bearing 4 70329 A/R Shim .3mm Thick
70330 A/R Shim .4mm Thick 70331 A/R Shim .5mm Thick
70332BH A/R Shim 1.0mm Thick 5 70577 1 Crown Gear 19 Teeth 6 70466 1 Output Shaft 7 70797 1 Bearing 8 70987 1 Casing 9 70393 2 Plug
10 70468 1 Cover 11 70469 1 Cover 12 70570 1 Nut M30 x 1.5 13 70571 1 Cotter Pin B4 x 50 14 70337 A/R Shim .3mm Thick
70338 A/R Shim .4mm Thick 70339 A/R Shim .5mm Thick
70340 A/R Shim 1.0mm Thick 15 70802 1 Bearing 16 70579 1 Shaft 17 70304 2 Spring Pin 10 x 26 18 70472BH 1 Lower Housing 19 70891 8 Bolt 20 70800 2 Bearing 21 70575 2 Dust Excluder
REF. PART
NO. NO.
QTY. DESCRIPTION
22 70166 1 Shoulder Ring 23 70077 1 Blank Washer 24 70076 1 Castle Nut M30 x 2 25 70940 1 Bearing 26 70586 1 Castle Nut 27 70585 1 Cotter Pin 28 70581 1 Bevel Pinion 15 Teeth 29 70348 A/R Shim .3mm Thick
70349BH A/R Shim .4mm Thick
70350 A/R Shim .5mm Thick
70351 A/R Shim 1.0mm Thick 30 70988 1 Input Shaft 1-3/4” 31 70583 1 Bevel Pinion 15 Teeth 32 70576 1 Protective Shield 33 15473 1 Cotter Pin 1/4 x 2-1/2” 34 70546 1 Vent Plug
SEPTEMBER, 2011
Page 28
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-8
REF. PART
NO. NO.
QTY. DESCRIPTION
1 70890 1 Cover 2 70578 1 Housing 3 70472BH 1 Lower Housing 4 70469 1 Cover 5 70582 1 Input Shaft 6 70889 1 Cross Shaft 7 70579 1 Lower Shaft 8 70473 1 Crown Gear (28 Teeth)
9 70465 2 Gear (15 Teeth) 10 70077 1 Washer 11 70797 1 Bearing 12 70802 1 Bearing 13 70801 1 Bearing 14 70800 3 Bearing 15 70462BH 12 Capscrew M10 x 22 16 70891 8 Bolt M10 x 25 17 70076 1 Hex Nut M30 x 2 18 70399 1 Locknut M40 x 1.5 19 70398 1 Spring Washer 20 70304 2 Spring Pin 21 70166 1 Shoulder Ring 22 70393 2 Plug 23 70463 1 Seal 24 70575 2 Dust Excluder 25 15473 1 Cotter Pin 1/4” x 2-1/2”
70826 LEFT HAND
GEARBOX ASSEMBLY
Models 3209-OR, 3210-OR
Serial Numbers 12-09999 and Below
Replaced by 70952 Gearbox
REF. PART
NO. NO.
QTY. DESCRIPTION
26 70337 A/R Shim .3mm Thick
70338 A/R Shim .4mm Thick 70339 A/R Shim .5mm Thick 70340 A/R Shim 1.0mm Thick
27 70329 A/R Shim .3mm Thick
70330 A/R Shim .4mm Thick 70331 A/R Shim .5mm Thick
70332BH A/R Shim 1.0mm Thick
28 70344 A/R Shim .3mm Thick
70345BH A/R Shim .5mm Thick 70346BH A/R Shim 1.0mm Thick
70347 A/R Shim .4mm Thick 29 70571 1 Cotter Pin 30 70570 1 Castle Nut 31 70576 1 Protective Shield 32 70580 1 Spacer 33 70546 1 Vent Plug
23
27
27
22 33
29
27
26
20
24
21
31
25
30
19
28
24
32
SEPTEMBER, 2011
Page 29
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-9
70542 GEARBOX ASSY. (540 RPM)
R.H. & L.H. Outboard for 3209, 3210, 3214
R.H. Outboard 3209-O, 3210-O
Serial Numbers 12-09999 and Below
REF. PART
NO. NO.
QTY. DESCRIPTION
70542 1 Gearbox Assy
1 70122 1 Cap 2 70121 1 Circlip, Internal 3 70256 1 Bearing 4 70459 1 Input Shaft 5 70304 2 Spring Pin 6 70258 1 Gear (18 Teeth) 7 70302 8 Screw, Allen Head M10 x 25 8 70546 1 Vent Plug
9 70795 1 Bearing 10 70407 1 Top Housing 11 70586 1 Castle Nut 12 70460 1 Gear (18 Teeth) 13 70800 2 Bearing 14 70266 1 Gasket 15 70507 1 Lower Housing 16 70588BH 1 Lower Shaft (70542 Assy. Only) 17 70575 1 Dust Excluder 18 70166 1 Shoulder Ring 19 70077 1 Flatwasher 20 70076 1 Castle Nut M30 x 2 21 15473 1 Cotter Pin 1/4 x 2-1/2” 22 70292 1 Plug 23 70115 1 Dust Cap 24 70333 A/R Shim .3mm Thick
70334 A/R Shim .4mm Thick 70335 A/R Shim .5mm Thick 70336 A/R Shim 1.0mm Thick
25 70337 A/R Shim .3mm Thick
70338 A/R Shim .4mm Thick 70339 A/R Shim .5mm Thick 70340 A/R Shim 1.0mm Thick
REF. PART
NO. NO.
QTY. DESCRIPTION
26 70344 A/R Shim .3mm Thick
70345BH A/R Shim .5mm Thick 70346BH A/R Shim 1.0mm Thick
70347 A/R Shim .4mm Thick 27 70576 1 Protective Shield 28 70585 1 Cotter Pin
A/R - As Required
SEPTEMBER, 2011
Page 30
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-10
70543 RIGHT & LEFT SIDE GEARBOX ASSEMBLY
For Models 13214 1000 RPM
Right Side 13209 1000 RPM
13210 1000 RPM
Serial Numbers 12-09999 and Below
REF. PART
NO. NO.
QTY. DESCRIPTION
70543 1 Gearbox Assy
1 70122 1 Cap 2 70121 1 Internal Clip 3 70333 A/R Shim .3mm Thick
70334 A/R Shim .4mm Thick 70335 A/R Shim .5mm Thick
70336 A/R Shim 1.0mm Thick 4 70256 1 Bearing 5 70459 1 Shaft 6 70406 1 Crown Wheel 19 Teeth 7 70302 8 Screw 8 70546 1 Vent Plug 9 70337 A/R Shim .3mm Thick
70338 A/R Shim .4mm Thick
70339 A/R Shim .5mm Thick
70340 A/R Shim 1.0mm Thick
10 70795 1 Bearing 11 70407 1 Casing 12 70570 1 Nut 13 70408 1 Bevel Pinion 15 Teeth 14 70344 A/R Shim .3mm Thick
70345BH A/R Shim .5mm Thick 70346BH A/R Shim 1.0mm Thick
70347 A/R Shim .4mm Thick
15 70800 2 Bearing 16 70266 1 Gasket 17 70507 1 Extension 18 70590 1 Shaft 19 70575 1 Dust Excluder 20 70166 1 Shoulder Ring 21 70077 1 Blank Washer 22 70076 1 Castle Nut 23 70571 1 Cotter Pin 24 70292 1 Plug 25 70115 1 Dust Excluder 26 70304 2 Spring Pin 27 70576 1 Protective Shield 28 15473 1 Cotter Pin 1/4 x 2-1/2”
SEPTEMBER, 2011
Page 31
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-11
REF. PART
NO. NO.
QTY. DESCRIPTION
1 44153BH 12 Capscrew M10 x 22 2 70463 2 Seal 35 x 56 x 8 3 70801 1 Bearing 4 70465 2 Pinon Gear (15 Teeth) 5 70466 1 Shaft 6 70797 1 Bearing 7 70578 1 Top Housing 8 70393 1 Plug
9 70468 1 Cover 10 70469 1 Cover 11 70546 1 Vent Plug 12 70802 1 Bearing 13 70579 1 Bottom Shaft 14 70304 2 Spring Pin 15 70472BH 1 Lower Housing 16 70891 8 Capscrew 12.9DCRT320 17 70800 2 Bearing 18 70575 2 Dust Excluder 19 70166 1 Shoulder Ring 20 70077 1 Washer 21 70076 1 Castle Nut M30 x 2
REF. PART
NO. NO.
QTY. DESCRIPTION
22 15473 1 Cotter Pin 1/4 x 2-1/2” 23 70399 1 Locknut M40 x 1.5 24 70398 1 Washer, Spring 40 x 62 x 1.25 25 70473 1 Crown Gear (28 Teeth) 26 70958 1 Input Shaft 27 70329 A/R Shim .3mm Thick
70330 A/R Shim .4mm Thick 70331 A/R Shim .5mm Thick
70332BH A/R Shim 1.0mm Thick
28 70337 A/R Shim .3mm Thick
70338 A/R Shim .4mm Thick 70339 A/R Shim .5mm Thick 70340 A/R Shim 1.0mm Thick
29 70344 A/R Shim .3mm Thick
70345BH A/R Shim .5mm Thick 70346BH A/R Shim 1.0mm Thick
70347 A/R Shim .4mm Thick 30 70571 1 Cotter Pin B4 x 50 31 70570 1 Nut M30 x 1.5 32 70576 1 Protective Shield 33 70957 1 Bearing
70949 CENTER GEARBOX ASSEMBLY
Used on 3200 Series Models with
Serial Numbers 12-09999 and Below
Replaced by 70983 Gearbox Asssembly
32
31
33
30
SEPTEMBER, 2011
Page 32
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-12
REF. PART
NO. NO.
QTY. DESCRIPTION
70983 1 Gearbox Assy
1 44153BH 12 Capscrew M10 x 22 2 70463 2 Seal 35 x 56 x 8 3 70801 1 Bearing 4 70465 2 Pinon Gear (15 Teeth) 5 70466 1 Shaft 6 70797 1 Bearing 7 70987 1 Top Housing 8 70393 1 Plug
9 70468 1 Cover 10 70469 1 Cover 11 70546 1 Vent Plug 12 70802 1 Bearing 13 70579 1 Bottom Shaft 14 70304 2 Spring Pin 15 70472BH 1 Lower Housing 16 70891 8 Capscrew 12.9DCRT320 17 70800 2 Bearing 18 70575 2 Dust Excluder 19 70166 1 Shoulder Ring 20 70077 1 Washer 21 70076 1 Castle Nut M30 x 2
REF. PART
NO. NO.
QTY. DESCRIPTION
22 15473 1 Cotter Pin 1/4 x 2-1/2” 23 70586 1 Nut M40 x 1.5 24 70585 1 Cotter Pin 25 70989 1 Crown Gear (28 Teeth) 26 70988 1 Input Shaft 27 70329 A/R Shim .3mm Thick
70330 A/R Shim .4mm Thick 70331 A/R Shim .5mm Thick
70332BH A/R Shim 1.0mm Thick
28 70337 A/R Shim .3mm Thick
70338 A/R Shim .4mm Thick 70339 A/R Shim .5mm Thick 70340 A/R Shim 1.0mm Thick
29 70348 A/R Shim .3mm Thick
70349BH A/R Shim .4mm Thick
70350 A/R Shim .5mm Thick
70351 A/R Shim 1.0mm Thick 30 70571 1 Cotter Pin B4 x 50 31 70570 1 Nut M30 x 1.5 32 70576 1 Protective Shield 33 70940 1 Bearing
70983 CENTER GEARBOX ASSEMBLY
540 RPM
Used on 3200 Series Models with
Serial Numbers 12-09999 and Below
33
30
32
31
SEPTEMBER, 2011
Page 33
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-13
REF. PART
NO. NO.
QTY. DESCRIPTION
1 70890 1 Cover 2 70578 1 Housing 3 70472BH 1 Lower Housing 4 70469 1 Cover 5 70956 1 Input Shaft 6 70889 1 Cross Shaft 7 70579 1 Lower Shaft 8 70473 1 Crown Gear (28 Teeth)
9 70465 2 Gear (15 Teeth) 10 70077 1 Washer 11 70797 1 Bearing 12 70802 1 Bearing 13 70801 1 Bearing 14 70800 2 Bearing 15 44153BH 12 Capscrew M10 x 22 16 70891 8 Bolt M10 x 25 17 70076 1 Hex Nut M30 x 2 18 70399 1 Locknut M40 x 1.5 19 70398 1 Spring Washer 20 70304 2 Spring Pin 21 70166 1 Shoulder Ring
70952 LEFT HAND
GEARBOX ASSEMBLY
Used on 3200 Series Models with
Serial Numbers 12-09999 and Below
Replaced by 70984 Gearbox Assembly
REF. PART
NO. NO.
QTY. DESCRIPTION
22 70393 2 Plug 23 70463 1 Seal 24 70575 2 Dust Excluder 25 15473 1 Cotter Pin 1/4” x 2-1/2” 26 70337 A/R Shim .3mm Thick
70338 A/R Shim .4mm Thick 70339 A/R Shim .5mm Thick 70340 A/R Shim 1.0mm Thick
27 70329 A/R Shim .3mm Thick
70330 A/R Shim .4mm Thick 70331 A/R Shim .5mm Thick
70332BH A/R Shim 1.0mm Thick
28 70344 A/R Shim .3mm Thick
70345BH A/R Shim .5mm Thick 70346BH A/R Shim 1.0mm Thick
70347 A/R Shim .4mm Thick 29 70571 1 Cotter Pin 30 70570 1 Castle Nut 31 70576 1 Protective Shield 32 70546 1 Vent Plug 33 70957 1 Bearing
30
SEPTEMBER, 2011
Page 34
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-14
REF. PART
NO. NO.
QTY. DESCRIPTION
70984 1 Gearbox Assy
1 70890 1 Cover 2 70987 1 Housing 3 70472BH 1 Lower Housing 4 70469 1 Cover 5 70988 1 Input Shaft 6 70889 1 Cross Shaft 7 70579 1 Lower Shaft 8 70989 1 Crown Gear (28 Teeth)
9 70465 2 Gear (15 Teeth) 10 70077 1 Washer 11 70797 1 Bearing 12 70802 1 Bearing 13 70801 1 Bearing 14 70800 2 Bearing 15 44153BH 12 Capscrew M10 x 22 16 70891 8 Bolt M10 x 25 17 70076 1 Hex Nut M30 x 2 18 70586 1 Castle Nut M40 x 1.5 19 70585 1 Cotter Pin 20 70304 2 Spring Pin 21 70166 1 Shoulder Ring
70984 LEFT HAND
GEARBOX ASSEMBLY
Used on 3200 Series Models with
Serial Numbers 12-09999 and Below
REF. PART
NO. NO.
QTY. DESCRIPTION
22 70393 2 Plug 23 70463 1 Seal 24 70575 2 Dust Excluder 25 15473 1 Cotter Pin 1/4” x 2-1/2” 26 70337 A/R Shim .3mm Thick
70338 A/R Shim .4mm Thick 70339 A/R Shim .5mm Thick 70340 A/R Shim 1.0mm Thick
27 70329 A/R Shim .3mm Thick
70330 A/R Shim .4mm Thick 70331 A/R Shim .5mm Thick
70332BH A/R Shim 1.0mm Thick
28 70348 A/R Shim .3mm Thick
70349BH A/R Shim .4mm Thick
70350 A/R Shim .5mm Thick
70351 A/R Shim 1.0mm Thick 29 70571 1 Cotter Pin 30 70570 1 Castle Nut 31 70576 1 Protective Washer 32 70546 1 Vent Plug 33 70940 1 Bearing
30
SEPTEMBER, 2011
Page 35
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-15
50018605 CENTER (INPUT)
GEARBOX ASSEMBLY (540 RPM)
Manufactured by Omni
Used on Models 3209 & 3210
Serial Numbers 12-10000 and Above
Replaced by 71204 Gearbox Assembly
50018606 CENTER (INPUT)
GEARBOX ASSEMBLY (1000 RPM)
Manufactured by Omni
Used on Models 13209 & 13210
Serial Numbers 12-10000 and Above
Replaced by 71205 Gearbox Assembly
REF. PART
NO. NO.
QTY. DESCRIPTION
1 50025402 1 Housing 2 50025403 2 Cap, Thru 3 50025404 1 Cap, Cantilevered 4 50025412 1 Gear, Output, 13T (50018605)
50025415 1 Gear, Output, 18T (50018606)
5 50025413 1 Gear, Input, 24T (50018605)
50025414 1 Gear, Input, 22T (50018606) 6 50025418 1 Shaft, Input 7 50025420 1 Shaft, Output 8 50053364 2 Bearing Assembly 9 50025423 1 Bearing Assembly
10 50025422 1 Bearing Assembly 11 50025426 1 Seal, Input 12 50025429 2 Seal, Horizontal Input 13 50025432 A/R Gasket, .1mm, Output 14 50025433 A/R Gasket, .2mm, Output
REF. PART
NO. NO.
QTY. DESCRIPTION
15 50025434 A/R Gasket, .5mm, Output 16 50025435 A/R Gasket, .1mm, Input Cap 17 50025436 A/R Gasket, .2mm, Input Cap 18 50025437 A/R Gasket, .5mm, Input Cap 19 21020724 1 Cotter Pin 20 44340BH 16 Capscrew M10 x 1.5 x 25 21 44281BH 8 Capscrew M12 x 1.75 x 35 22 50025459 2 Hex Nut, Slotted 1-3/8” 23 44198 16 Lockwasher M10 24 44200BH 8 Lockwasher M12 25 50025464 1 Pipe Plug, 3/8” – 18 NPT 26 80538 1 Vent Plug 27 88850 1 Retaining Ring 28 50025467 1 Retaining Ring, 50mm
*29 50025451 2 Spacer, Output
Used on 50018606 Gearbox Only)
25
7
27
29*
4
8
2
12
23
20
13
14
15
18
17
16
22
29*
5
10
6
9
3
11
21
24
19
8
2
12
20
23
26
1
28
SEPTEMBER, 2011
Page 36
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-16
REF. PART
NO. NO.
QTY. DESCRIPTION
1 50025401 1 Housing 2 50025403 1 Cap, Thru 3 50025404 1 Cap, Cantilevered 4 50025405 1 Cap, Blank 5 50025412 2 Gear, Output, 13T 6 50025413 1 Gear, Input 24T 7 50025418 1 Shaft, Input 1.75” – 20 Spline 8 50025419 1 Shaft, Output, Tapered Spline 18T
9 50025421 1 Shaft, Output 1-3/4” – 20 Spline 10 70800 1 Bearing Assembly 11 70410 1 Bearing Assembly 12 50053364 2 Bearing Assembly 13 50025423 1 Bearing Assembly 14 50025422 1 Bearing Assembly 15 50025426 1 Seal, Input 16 50025430 1 Seal, Vertical Output 17 50025429 2 Seal, Hor. Output 18 50025432 A/R Gasket, .1mm 19 50025433 A/R Gasket, .2mm 20 50025434 A/R Gasket, .5mm 21 50025434 A/R Gasket, .1mm 22 50025436 A/R Gasket, .2mm 23 50025472 1 Inspection Cover 24 50025448 A/R Shim, .10mm 25 50025449 A/R Shim, .20mm 26 50025450 A/R Shim, .50mm 27 50025451 1 Spacer, Output
REF. PART
NO. NO.
QTY. DESCRIPTION
28 50025452 1 Spacer, Output 29 44459BH 1 Cotter Pin 30 21020724 2 Cotter Pin 31 44281BH 8 Capscrew M12 x 35 32 44340BH 16 Capscrew M10 x 25 33 50025459 2 Hex Nut 1-3/8” – 18 UNF 34 50025460 1 Hex Nut M36 35 44198 16 Lockwasher M10 36 44200BH 8 Lockwasher M12 37 78719 1 Pipe Plug, 1/2” – 14 NPT 38 50025464 1 Pipe Plug, 3/8” – 18 NPT 39 80538 1 Vent Plug 40 88850 1 Retaining Ring 41 50025467 1 Retaining Ring 50MM 42 50025469 1 Retaining Ring 110MM 43 50025471 1 Protection Seal
32 35
17
2
12
40
18
19
20
39
23
38
1
9
12
4
35
32
37
30
33
27
5
10
8
11
28
42
43
34
29
16
7
15
41
13
31
36
14
33
30
21
22
6
3
24, 25, 26
5
32 35
50018609 INPUT GEARBOX
ASSEMBLY (540 RPM)
Manufactured by Omni
Used on 3209 & 3210 Offset Models
Serial Numbers 12-10000 and Above
Replaced by 71206 Gearbox
SEPTEMBER, 2011
Page 37
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-17
REF. PART
NO. NO.
QTY. DESCRIPTION
1 50025400 1 Housing 2 50025406 1 Cap, Blank 3 50025408 1 Gear, 20T (50018603)
50025407 1 Gear, 21T (50018596)
4 50025409 1 Gear, Pinion, 19T (50018603)
50025407 1 Gear, 21T (50018596) 5 50025416 1 Shaft,Input 1.75” – 20 Spline 6 50025417 1 Shaft, Output, 18T 7 70800 1 Bearing Assembly 8 70796 2 Bearing Assembly 9 70410 1 Bearing Assembly
10 50068116 1 Seal, Input 11 50025430 1 Seal, Output 12 50025438 A/R Gasket, .2MM 13 50025439 A/R Gasket, .3MM 14 50025440 A/R Gasket, .5MM 15 50025441 A/R Shim, Input, 1.8MM 16 50025442 A/R Shim, Input, 2MM 17 50025443 A/R Shim, Input, 2.2MM 18 50025444 A/R Shim, Input, 2.5MM 19 50025445 A/R Shim, Input, .10MM 20 50025446 A/R Shim, Input, .20MM 21 50025447 A/R Shim, Input, .50MM 22 50025448 A/R Shim, Output, .10MM 23 50025449 A/R Shim, Output, .20MM 24 50025450 A/R Shim, Output, .50MM 25 50025452 1 Spacer, Output 26 44459BH 1 Cotter Pin 27 21020724 1 Cotter Pin 28 44299BH 8 Capscrew M8 – 1.25 x 25 29 44202 4 Capscrew M10 – 1.5 x 30 30 50025459 1 Hex Nut 1-3/8” – 18 UNF 31 50025460 1 Hex Nut M36 32 44311BH 8 Lockwasher M8
REF. PART
NO. NO.
QTY. DESCRIPTION
33 44198 4 Lockwasher M10 34 78719 1 Pipe Plug 1/2” 35 50025464 1 Pipe Plug 3/8” – 18 NPT 36 80538 1 Vent Plug 37 88850 1 Retaining Ring, External 38 50025468 1 Retaining Ring, External 39 50025469 1 Retaining Ring, Internal 40 50025470 1 Inspection Cover 41 50025471 1 Protective Seal
*50018603 OUTBOARD GEARBOX
(540 RPM)
Manufactured by Omni
Used on 3209
*Serial Numbers 12-10000 and Above
Replaced by 71200 Gearbox
50018596 OUTBOARD GEARBOX
(540 RPM)
Manufactured by Omni
Used on 3209, 3210 & 3210 Offset Models
Serial Numbers 12-10000 and Above
Replaced by 70995BH Gearbox
29
2
12
13
14
15, 16, 17, 18
8
33
28
32
40
37
3
8
19
20
21
38
10
5
35
1
34
6
9
7
4
30
27
22 23 24
25
11
39
41
31
26
36
*Note: 3209 models serial numbers 12-00082 through 12-00126 used the 50018596 Gearbox Assembly.
SEPTEMBER, 2011
Page 38
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-18
REF. PART
NO. NO.
QTY. DESCRIPTION
1 50025400 1 Housing 2 50025406 1 Cap, Blank 3 50025410 1 Gear, 22T 4 50025411 1 Gear, Pinion, 18T 5 50025416 1 Shaft,Input 1.75” – 20 Spline 6 50025417 1 Shaft, Output, 18T 7 70800 1 Bearing Assembly 8 70796 2 Bearing Assembly 9 70410 1 Bearing Assembly
10 50068116 1 Seal, Input 11 50025430 1 Seal, Output 12 50025438 A/R Gasket, .2MM 13 50025439 A/R Gasket, .3MM 14 50025440 A/R Gasket, .5MM 15 50025441 A/R Shim, Input, 1.8MM 16 50025442 A/R Shim, Input, 2MM 17 50025443 A/R Shim, Input, 2.2MM 18 50025444 A/R Shim, Input, 2.5MM 19 50025445 A/R Shim, Input, .10MM 20 50025446 A/R Shim, Input, .20MM 21 50025447 A/R Shim, Input, .50MM 22 50025448 A/R Shim, Output, .10MM 23 50025449 A/R Shim, Output, .20MM 24 50025450 A/R Shim, Output, .50MM 25 50025452 1 Spacer, Output 26 44459BH 1 Cotter Pin 27 21020724 1 Cotter Pin 28 44299BH 8 Capscrew M8 – 1.25 x 25 29 44202 4 Capscrew M10 – 1.5 x 30 30 50025459 1 Hex Nut 1-3/8” – 18 UNF 31 50025460 1 Hex Nut M36
REF. PART
NO. NO.
QTY. DESCRIPTION
32 44311BH 8 Lockwasher M8 33 44198 4 Lockwasher M10 34 78719 1 Pipe Plug 1/2” 35 50025464 1 Pipe Plug 3/8” – 18 NPT 36 80538 1 Vent Plug 37 88850 1 Retaining Ring, External 38 50025468 1 Retaining Ring, External 39 50025469 1 Retaining Ring, Internal 40 50025470 1 Inspection Cover 41 50025471 1 Protective Seal
50018601 OUTBOARD GEARBOX
(1000 RPM)
Manufactured by Omni
Used on 13209 & 13210 Models
Serial Numbers 12-10000 and Above
Replaced by 71198 Gearbox
29
2
12
13
14
15, 16, 17, 18
8
33
28
32
40
37
4
8
19
20
21
38
10
5
35
1
34
6
9
7
3
30
27
22 23 24
25
11
39
41
31
26
36
SEPTEMBER, 2011
Page 39
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-19
71204 CENTER (INPUT)
GEARBOX ASSEMBLY (540 RPM)
Manufactured by Comer
Models: 3209 S/N 12-10000 through 12-10849,
3210 S/N 12-10000 through 12-21399
Ratio 1:1.85
Replaces 50018605 Gearbox (Omni)
Replaced by 50045614 Gearbox (B&P)
71205 CENTER (INPUT)
GEARBOX ASSEMBLY (1000 RPM)
Manufactured by Comer
Models: 13209 S/N 12-10000 through 12-10849,
13210 S/N 12-10000 through 12-21399
Ratio 1:1.22
Replaces 50018606 Gearbox (Omni)
Replaced by 50045615 Gearbox (B&P)
REF. PART
NO. NO.
QTY. DESCRIPTION
1 76867 1 Output Shaft 2 50068116 2 Oil Seal 3 44202 26 Capscrew M10 x 1.5 x 30 4 76868 2 Cover 5 71331 2 Bearing 6 70348 2 Shim 0.3 7 76879 1 Pinion Gear (71204)
76876 1 Pinion Gear (71205) 8 76870 1 Spacer 9 70752 2 Shim 0.3
10 70344 1 Shim 0.3 11 76877 1 Casing 12 70586 1 Castle Nut M40 13 50025422 1 Bearing 32310 14 76873 1 Cover 15 71523 1 Input Shaft
50047693 1 Input Shaft Kit (Includes Shaft,
Spacer & Cotter Pin)
1
16 76875 1 Oil Seal 17 50025423 1 Bearing
REF. PART
NO. NO.
QTY. DESCRIPTION
18 76881 1 Crown Gear (71204)
76869 1 Crown Gear (71205) 19 71492 1 Cotter Pin 20 70349BH 2 Shim 0.4 21 70350 2 Shim 0.5 22 70351 2 Shim 1.0 23 70753 2 Shim 0.4 24 70754 2 Shim 0.5 25 70755 2 Shim 1.0 26 70345BH 1 Shim 0.5 27 70346BH 1 Shim 1.0 28 70347 1 Shim 0.4 29 76913 1 Oil Level Plug 30 71524 1 Spacer
3
2
4
19
18
12
30
1
8
4
2
3
5
7
6, 20, 21, 22
9, 23, 24, 25
13
15*
14
3
17
16
10, 26, 27, 28
29
11
5
9, 23, 24, 25
6, 20, 21, 22
1
Some gearboxes have input shafts that are shorter than
the replacement shaft. Measure the length of the shaft before ordering. If it is not 13.00” long, order #50047693 Input Shaft Kit (includes ref. #15 input shaft, ref. #30 spacer and ref. #19 cotter pin.)
13.00”
SEPTEMBER, 2011
Page 40
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-20
REF. PART
NO. NO.
QTY. DESCRIPTION
1 76878 1 Output Shaft 2 50068116 1 Oil Seal 3 44202 26 Capscrew M10 x 1.5 x 30 4 76868 2 Cover 5 71331 2 Bearing 30209 6 70348 2 Shim 0.3 7 76879 2 Pinion Gear 8 76870 1 Spacer
9 70725 1 Cap 10 70752 2 Shim 0.3 11 70344 2 Shim 0.3 12 70800 1 Bearing 30210 13 76871 1 Casing 14 70410 1 Bearing 30212 15 50062245 1 Oil Seal 16 76661 1 Protective Washer 17 76872 1 Output Shaft 18 71492 2 Cotter Pin 19 70586 2 Castle Nut 20 76913 1 Oil Level Plug 21 50025422 1 Bearing 32310 22 76873 1 Cover 23 71523 1 Input Shaft
50047693 1 Input Shaft Kit (Includes Shaft,
Spacer & Cotter Pin)
1
REF. PART
NO. NO.
QTY. DESCRIPTION
24 76875 1 Oil Seal 25 50025423 1 Bearing 32210 26 76881 1 Crown Gear 27 70349BH 2 Shim 0.4 28 70350 2 Shim 0.5 29 70351 2 Shim 1.0 30 70753 2 Shim 0.4 31 70754 2 Shim 0.5 32 70755 2 Shim 1.0 33 70345BH 2 Shim 0.5 34 70346BH 2 Shim 1.0 35 70347 2 Shim 0.4 36 76664 1 Blank Washer 37 70418 1 Castle Nut 38 70419 1 Cotter Pin 39 71524 1 Spacer
71206 CENTER (INPUT) GEARBOX
540 RPM, RATIO 1:1.85
Manufactured by Comer
Models: 3209 S/N 12-10000 through 12-10849,
3210 Offest S/N 12-10000 through 12-21399
Replaces 50018609 Gearbox (Omni)
Replaced by 50045618 Gearbox (B&P)
2
3
4
7
5
8
18
26
21
23*
22
25
24
3
11, 33 34, 35
19
39
18
19
17
14
15
16
36
37
38
7
12
11, 33 34, 35
20
13
1
5
4
3
9
6, 27 28, 29
10, 32 31, 30
10, 30 31, 32
6, 27 28, 29
1
Some gearboxes have input shafts that are shorter than the replacement shaft. Measure the length of the shaft before ordering. If it is not 13.00” long, order #50047693 Input Shaft Kit (includes ref. #23 input shaft, ref. #39 spacer and ref. #18 cotter pin.)
13.00”
SEPTEMBER, 2011
Page 41
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-21
REF. PART
NO. NO.
QTY. DESCRIPTION
1 76658 1 Casting 2 76882 1 Pinion Gear, 19T 3 70796 2 Bearing 30209 4 50068116 1 Oil Seal 5 76659 1 Input Shaft 6 70189 2 Snap Ring 7 70752 2 Shim 0.3 8 76660 1 Top Plate
9 70586 1 Castle Nut M40 10 70344 1 Shim 0.3 11 70292 1 Oil Filler Plug 1/2” Gas 12 44595BH 4 Capscrew M10 x 1.5 x 14 13 70800 1 Bearing 30210 14 76661 1 Protective Washer 15 50062245 1 Oil Seal 16 70410 1 Bearing 30212 17 76663 1 Output Shaft 18 80538 1 1/2” Gas Plug 19 70585 1 Cotter Pin 20 70725 1 Cap 21 76883 1 Crown Gear 20T 22 70740 1 Spacer 23 70722 1 Snap Ring 24 76634 1 Shim 1.0 25 70753 2 Shim .4 26 70754 2 Shim .5 27 70755 2 Shim 1.0 28 70345BH 1 Shim .5 29 70346BH 1 Shim 1.0 30 70347 1 Shim .4 31 76664 1 Blank Washer 32 70418 1 Castle Nut 33 70419 1 Cotter Pin
71200 OUTBOARD GEARBOX
540 RPM, RATIO 1:1.053
Manufactured by Comer
Model: 3209 S/N 12-10000 through 12-10849
Replaces 50018603 Gearbox (Omni)
1
Replaced by 50045613 Gearbox (B&P)
20
7,25 26, 27
6
12
18
8
3
1
19
9
24
5
11
23
21
22
3
7
6
4
2
13
33
32
31
14
15
16
17
10, 28 29, 30
1
Omni gearbox has 6 holes in top plate. Comer gearbox has 4 holes in top plate.
SEPTEMBER, 2011
Page 42
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-22
REF. PART
NO. NO.
QTY. DESCRIPTION
1 76658 1 Casting 2 70960 2 Gear 21T 3 70796 2 Bearing 30209 4 50068116 1 Oil Seal 5 76659 1 Input Shaft 6 70189 2 Snap Ring 7 70752 2 Shim 0.3 8 76660 1 Top Plate
9 70586 1 Castle Nut M40 10 70344 1 Shim 0.3 11 70292 1 Oil Filler Plug 1/2” Gas 12 44595BH 4 Capscrew M10 x 1.5 x 14 13 70800 1 Bearing 30210 14 76661 1 Protective Washer 15 50062245 1 Oil Seal 16 70410 1 Bearing 30212 17 76663 1 Output Shaft 18 80538 1 1/2” Gas Plug 19 70585 1 Cotter Pin 20 70725 1 Cap 21 70740 1 Spacer 22 70722 1 Snap Ring 23 76634 1 Shim 1.0 24 70753 2 Shim .4 25 70754 2 Shim .5 26 70755 2 Shim 1.0 27 70345BH 1 Shim .5 28 70346BH 1 Shim 1.0 29 70347 1 Shim .4 30 76664 1 Blank Washer 31 70418 1 Castle Nut 32 70419 1 Cotter Pin
70995BH OUTBOARD GEARBOX
(540 RPM)
Manufactured by Comer
Models: 3209 S/N 12-10000 through 12-10849,
3210 & 3210 Offset S/N 12-10000 through 12-21399
Replaces 50018596 Gearbox (Omni)
1
Replaced by 50045607 (B&P)
20
7,24 25, 26
6
12
18
8
3
22
1
19
23
9
5
11
21
2
3
7
6
4
2
13
32
31
30
14
15
16
17
10, 27 28, 29
1
Omni gearbox has 6 holes in top plate. Comer gearbox has 4 holes in top plate.
SEPTEMBER, 2011
Page 43
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-23
REF. PART
NO. NO.
QTY. DESCRIPTION
24 76634 1 Shim, 1mm 25 70753 1 Shim, .4mm 26 70754 1 Shim, .5mm 27 70755 1 Shim, 1mm 28 70345BH 1 Shim, .5mm 29 70346BH 1 Shim, 1mm 30 70347 1 Shim, .4mm 31 76664 1 Blank Washer 32 70418 1 Castle Nut M36 33 70419 1 Cotter Pin
71198 GEARBOX ASSEMBLY
1000 RPM, Ratio 1:.82
Manufactured by Comer
Models: 13209 S/N 12-10000 through 12-10849,
13210 S/N 12-10000 through 12-21399
Replaces 50018601 Gearbox (Omni)
1
Replaced by 50045612 Gearbox (B&P)
20
6
7
3
11
19
9
24
17
16
15
14
32
31
30 29 28 10
2
13
33
5
12
18
8
1
23
21
22
3
6
4
7
25
26
27
REF. PART
NO. NO.
QTY. DESCRIPTION
1 76658 1 Casting 2 76668 1 Gear, Ouput, 22 Teeth 3 70796 2 Bearing 4 50068116 1 Oil Seal 5 76659 1 Input Shaft 1-3/4” 6 70189 2 Snap Ring 7 70752 2 Shim .3mm 8 76660 1 Top Plate
9 70586 1 Castle Nut 10 70344 1 Shim .3mm 11 70292 1 Oil Filler Plug 1/2” Gas 12 44595BH 4 Capscrew M10 x 14 Gr.8.8 13 70800 1 Bearing 14 76661 1 Protective Washer 15 50062245 1 Oil Seal 16 70410 1 Bearing 17 76663 1 Shaft, Output 18 80538 1 Vent Plug 19 70585 1 Cotter Pin 20 70725 1 Cap 21 76667 1 Gear, Input, 18 Teeth 22 70740 1 Spacer 23 70722 1 Snap Ring
1
The Comer gearbox has 4 holes in the top plate.
The Omni gearbox has 6 holes in the top plate.
SEPTEMBER, 2011
Page 44
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-24
50045614 CENTER GEARBOX
540 RPM, RATIO 1:1.85
Manufactured by B&P
Models: 3209 (S/N 12–10850 and above)
3210 (Serial numbers 12-21400 and above)
Replaces 71204 Gearbox Assembly
50045615 CENTER GEARBOX
1000 RPM, RATIO 1:1.22
Manufactured by B&P
Model: 13210 (Serial Numbers 12-21400 and Above)
Replaces 71205 Gearbox Assembly
REF. PART
NO. NO.
QTY. DESCRIPTION
50045614 1 Gearbox Assy 50045615 1 Gearbox Assy
1 50053048 1 Housing 2 50053046 2 Cap, Thru 3 50053053 1 Front Cover 4 50053047 1 Gear, Output, 13T (50045614)
50053056 1 Gear, Output, 18T (50045615)
5 50053051 1 Gear, Input, 24T (50045614)
50053058 1 Gear, Input, 22T (50045615) 6 50053055 1 Shaft, Input 1-3/4” 20 Spline 7 50053050 1 Shaft, Output 1-3/4” 20 Spline 8 50053364 2 Bearing Assembly 9 50053078 1 Bearing Assembly
10 50053079 1 Bearing Assembly 11 50053054 1 Seal, Input 12 50053309 2 Seal, Horizontal Input 13 50053049 2 Gasket Set, Output
REF. PART
NO. NO.
QTY. DESCRIPTION
14 50053052 A/R Gasket Set, Input 15 50053070 1 Cotter Pin 16 50053365 16 Capscrew M10 x 1.5 x 25 17 50053366 8 Capscrew M12 x 1.75 x 35 18 50053038 2 Hex Nut, Slotted 1-3/8” 19 50053074 16 Lockwasher M10 20 50053057 8 Lockwasher M12 21 50053026 1 Pipe Plug, 3/8” – 18 NPT 22 81572 1 Vent Plug 23 50053033 1 Retaining Ring 24 50053035 1 Retaining Ring, 50mm 25 50053368 2 Spacer, Output
(
Used on 50045615 Gearbox Only)
21
7
23
25*
4
2
12
19
8
16
13
14
18
25*
5
10
6
9
3
11
17
20
15
8
2
12
16
19
22
1
13
24
SEPTEMBER, 2011
Page 45
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-25
REF. PART
NO. NO.
QTY. DESCRIPTION
50045618 1 Gearbox Assy
1 50053066 1 Housing 2 50053046 1 Cap, Thru 3 50053053 1 Cap, Cantilevered 4 50053062 1 Cap, Blank 5 50053047 2 Gear, Output, 13T 6 50053051 1 Gear, Input 24T 7 50053055 1 Shaft, Input 1-3/4” – 20 Spline 8 50053065 1 Shaft, Output, Tapered Spline 18T
9 50053064 1 Shaft, Output 1-3/4” – 20 Spline 10 50053367 1 Bearing Assembly 11 70410 1 Bearing Assembly 12 50053364 2 Bearing Assembly 13 50053078 1 Bearing Assembly 14 50053079 1 Bearing Assembly 15 50053054 1 Seal, Input 16 50053460 1 Seal, Vertical Output 17 50053309 1 Seal, Hor. Output 18 50053049 3 Gasket Set 19 50053052 1 Gasket Set 20 50053063 1 Inspection Cover 21 50053039 1 Shim 22 50053368 1 Spacer, Output 23 50053024 1 Spacer, Output
REF. PART
NO. NO.
QTY. DESCRIPTION
24 50053376 1 Cotter Pin 6.3 x 60 25 50053371 2 Cotter Pin 5 x 65 26 50053373 8 Capscrew M12 x 35 27 50053369 24 Capscrew M10 x 25 28 50053038 2 Castle Nut 29 50053059 1 Castle Nut 30 50053370 16 Lockwasher M10 31 50053374 8 Lockwasher M12 32 50053020 1 Pipe Plug, 1/2” – 14 NPT 33 50053372 1 Pipe Plug, 3/8” – 18 NPT 34 81572 1 Vent Plug 35 50053033 2 Retaining Ring 36 50053375 1 Retaining Ring 110MM 37 50053021 1 Protection Seal 38 50053022 1 Belleville Washer
27 30
17
2
12
35
18
18
34
20
33
1
9
12
18
4
30
27
32
25
28
22
5
21
10
8
11
23
36
37
29 38
24
16
7
15
35
13
26
31
14
28
25
19
6
3
5
27 30
50045618 CENTER GEARBOX
540 RPM, RATIO 1:1.85
Manufactured by B&P
Models: 3209 Offset
(Serial Numbers 12-10850 and Above)
3210 Offset
(Serial Numbers 12-21400 and Above)
Replaces 71206 Gearbox (Mfr. by Comer)
SEPTEMBER, 2011
Page 46
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-26
REF. PART
NO. NO.
QTY. DESCRIPTION
50045613 1 Gearbox Assy 50045607 1 Gearbox Assy
1 50053041 1 Housing 2 50053030 1 Cap, Blank 3 50053045 1 Gear, 20T (50045613)
50053034 1 Gear, 21T (50045607)
4 50053044 1 Gear, Pinion, 19T (50045613)
50053034 1 Gear, 21T (50045607) 5 50053037 1 Shaft,Input 1.75” – 20 Spline 6 50053040 1 Shaft, Output, 18T 7 50053069 1 Bearing Assembly 8 70796 2 Bearing Assembly 9 70410 1 Bearing Assembly
10 50053071 1 Seal, Input 11 50053067 1 Seal, Output 12 50053031 1 Gasket Set 13 50053036 2 Shim, Input, .10MM 14 50053039 1 Shim, Output 15 50053024 1 Spacer, Output 16 50053077 1 Cotter Pin 6.3 x 60 17 50053070 1 Cotter Pin 5 x 65 18 50053076 8 Capscrew M8 – 1.25 x 25 19 50053073 4 Capscrew M10 – 1.5 x 30 20 50053038 1 Castle Nut 21 50053025 1 Castle Nut 22 50053028 8 Lockwasher M8 23 50053074 4 Lockwasher M10
REF. PART
NO. NO.
QTY. DESCRIPTION
24 50053020 1 Plug 25 50053026 1 Plug 3/8” – 18 NPT 26 81572 1 Vent Plug 27 50053033 1 Retaining Ring, External 28 50053060 1 Retaining Ring, External 29 50053023 1 Retaining Ring, Internal 30 50053029 1 Top Cover 31 50053021 1 Protective Seal 32 50053032 1 Snap Ring 33 50053027 1 Gasket 34 50053022 1 Belleville Washer
19
2
12
32
8
23
18
22
30
33
27
3
8
13
13
28
10
5
25
1
24
6
97
4
20
17
14
15
11
29
31
34
21
16
26
50045613 OUTBOARD GEARBOX
540 RPM, RATIO 1:1.05
Manufactured by B&P
Used on 3209
(Serial numbers 12-10850 and above)
Replaces 71200 Gearbox (Comer)
50045607 OUTBOARD GEARBOX
540 RPM, RATIO 1:1
Manufactured by B&P
Models: 3209
(Serial numbers 12-10850 and above)
3210 & 3210 Offset
(Serial numbers 12-21400 and above)
Replaces 70995BH Gearbox (Comer)
SEPTEMBER, 2011
Page 47
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-27
REF. PART
NO. NO.
QTY. DESCRIPTION
50045612 1 Gearbox Assy
1 50053041 1 Housing 2 50053030 1 Cap, Blank 3 50053043 1 Gear, 22T 4 50053042 1 Gear, Pinion, 18T 5 50053037 1 Shaft,Input 1.75” – 20 Spline 6 50053040 1 Shaft, Output, 18T 7 50053069 1 Bearing Assembly 8 70796 2 Bearing Assembly
9 70410 1 Bearing Assembly 10 50053071 1 Seal, Input 11 50053067 1 Seal, Output 12 50053031 1 Gasket Set 13 50053032 1 Snap Ring 14 50053036 2 Shim 15 50053039 1 Shim 16 50053024 1 Spacer, Output 17 50053077 1 Cotter Pin 6.3 x 60 18 50053070 1 Cotter Pin 5 x 65 19 50053076 8 Capscrew M8 – 1.25 x 25 20 50053073 4 Capscrew M10 – 1.5 x 30 21 50053038 1 Castle Nut 22 50053025 1 Castle Nut 23 50053028 8 Lockwasher M8
REF. PART
NO. NO.
QTY. DESCRIPTION
24 50053074 4 Lockwasher M10 25 50053020 1 Pipe Plug 26 50053026 1 Pipe Plug 3/8” – 18 NPT 27 81572 1 Vent Plug 28 50053033 1 Retaining Ring, External 29 50053060 1 Retaining Ring, External 30 50053023 1 Retaining Ring, Internal 31 50053029 1 Inspection Cover 32 50053021 1 Protective Seal 33 50053027 1 Gasket 34 50053022 1 Belleville Washer
50045612 OUTBOARD GEARBOX
1000 RPM, RATIO 1.22:1
Manufactured by B&P
Model: 13210
Serial Numbers 12-21400 and above
Replaces 71198 Gearbox
20
2
12
8
13
24
19
23
31
33
28
4
8
14
14
29
10
5
26
1
25
6
9
7
3
21
15
18
16
11
30
32
22
34
17
27
SEPTEMBER, 2011
Page 48
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
REF. PART
NO. NO.
QTY. DESCRIPTION
1 20312 A/R Lynch Pin 2 44216 A/R Flatwasher M8 3 90560 A/R Capscrew M8 x 1.25 x 15 Gr.8.8 4 81592 1 Input Shield 5 90140BH A/R R.H. Shield Bracket 6 90141BH A/R L.H. Shield Bracket 7 90143 2 Cross Shaft Cover 3209
90320BH 1 Cross Shaft Cover 3209 Offset 90155BH 2 Cross Shaft Cover 3210
N/A 1 Cross Shaft Cover 3210 Offset N/A 2 Cross Shaft Cover 3214
SHIELDS & RELATED PARTS
For 3200 Series Models
Serial Numbers 12-09999 and Below
5
7
1
3
2
6
4
2
3
46-4-28
SEPTEMBER, 2011
Page 49
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-29
REF. PART
NO. NO.
QTY. DESCRIPTION
1 20312 A/R Lynch Pin 2 –––– A/R Flatwasher 3/8” 3 50018166 A/R Capscrew M10 ZP 4 50017584 1 Input Shield Assembly 5 50032274 A/R R.H. Shield Bracket, 3209-O, 3210, 3210-O
50017598 A/R R.H. Shield Bracket, 3209 &
Old Style 3209-O, 3210, 3210-O
6 50032275 A/R L.H. Shield Bracket, 3209-O, 3210, 3210-O
50017597 A/R L.H. Shield Bracket, 3209 &
Old Style 3209-O, 3210, 3210-O
*7 50017959 2 Cross Shaft Cover, 3209
50035353 1 Cross Shaft Cover, 3209-O (See note) 50036486 2 Cross Shaft Cover, 3210 (See note)
50034309 1 Cross Shaft Cover, 3210-O (See note) 8 83106 1 Shield Hinge Pin 9 67716 2 Cap Push Nut
10 50017585 1 Shield Mount Weldment 11 50028366 1 Warranty Decal
SHIELDS AND RELATED PARTS
For 3200 Series
Serial Numbers 12-10000 and Above
9
1
4
8
9
10
6
5
1
1
7
3
2
2
3
11
SHIELD KITS
For older style 3209-O, 3210, 3210-O
Contains Cross Shaft Cover(s), Shield Brackets & Fasteners
3209-O 50035715 Shield Kit 3210 50036647 Shield Kit 3210-O 50035716 Shield Kit
*Note: Some earlier models have a different style Cross Shield Cover. To replace Cross Shaft Cover(s) on older style 3209 Offset, 3210 & 3210 Offset models, you must order a shield replacement kit, shown below. Measure shield to determine which style is needed. (See diagram at left.)
9.54”
4.71”
10.54”
6.97”
END VIEW
CROSS SHIELDS & BRACKETS
OLD STYLE
CROSS SHIELD
OLD STYLE
SHIELD BRACKET
NEW STYLE
SHIELD BRACKET
NEW STYLE
CROSS SHIELD
7.12”
7.62”
5.00”
6.26”
SEPTEMBER, 2011
Page 50
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-4-30
7
16, 17, 18, 19
10
4
10
4
10
10
8
9
5
11, 12
11, 12
6
5
11, 12
3
2
13, 14, 15, 12
3
2
11, 12
6
13, 14, 15, 12
1
11, 12
DRIVELINE SHIELDING, NEW STYLE
3210, 13210 and 3210-O
Ref. Part
No. No. Description Qty.
1 50062095 Driveline Shnield Cone Assy 1 2 50069493 Shield, Bottom w/Decal (3210, 13210) 2
50069494 Shield, Bottom w/Decal (3210-O) 1 3 D546 Decal, Danger - Shield Missing A/R 4 50069480 Shield Weldment (3210, 13210) 2
50069492 Shield Weldment (3210-O) 1 5 50068454 Shield Bracket, RH A/R 6 50068457 Shield Bracket, LH A/R 7 50035829 Tube, Owner’s Manual 1 8 50035830 Seal 1 9 50035851 Cap 1
10 20312 Lynch Pin A/R 11 ----- Capscrew, M10 x 1.5-20 A/R 12 ----- Flatwasher, 3/8 A/R 13 ----- Capscrew, 3/8 x 1 Gr 5 A/R 14 ----- Hex Nut, 3/8 A/R 15 ----- Lockwasher, 3/8 A/R 16 ----- Capscrew, 1/4 x 7/8 Gr 5 3 17 ----- Flatwasher, 1/4 3 18 ----- Lockwasher, 1/4 3 19 ----- Hex Nut, 1/4 A/R
SEPTEMBER, 2011
Page 51
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
DRIVESHAFTS FOR 3200 SERIES PULL MODELS (Mfd. by Bondioli & Pavesi)
Serial Numbers 12-09999 and Below
84722 DRIVESHAFT ASSEMBLY
540 RPM
1 3/8” - 6 Spline Tractor Yoke
Replaced by 76405 Driveshaft Assy.
84014 DRIVESHAFT ASSEMBLY
1000 RPM
1 3/8” - 21 Spline Tractor Yoke
Replaced by 76412 Driveshaft Assy.
SEPTEMBER, 2011
84723BH DRIVESHAFT ASSEMBLY
1000 RPM
1 3/4” - 20 Spline Tractor Yoke
Replaced by 76406 Driveshaft Assy.
REF. PART
NO. NO.
1 84728 1 Front Half Assy. (540 RPM)
84026 1 Front Half Assy. (1000 RPM 1 3/8” Spl.) 84725 1 Front Half Assy. (1000 RPM 1 3/4” Spl.)
2 64973 1 Yoke Assy. (540 RPM)
78189 1 Yoke Assy. (1000 RPM 1 3/8” Spl.) 68170 1 Yoke Assy. (1000 RPM 1 3/4” Spl.)
3 63945 2 Q.D. Pin Kit (540 RPM)
78190 2 Q.D. Pin Kit (1000 RPM 1 3/8” Yoke) *68169 2 Q.D. Pin Kit (1000 RPM 1 3/4” Yoke) *86723 2 O.D. Pin Kit (1000 RPM 1 3/4” Yoke)
4 64963 1 Cross Bearing Kit 5 63956 1 Grease Fitting 6 84727 1 Yoke & Tube w/Decals
84724 1 Yoke & Tube w/Decals (1000 RPM 1 3/4”)
7 63946 1 Grease Fitting 8 78786 1 Danger Decal
9 68179 1 Outer Shield Bearing 10 50042072 1 Danger Decal 11 78102BH 1 Rear Half Assy. 12 68170 1 Implement Yoke 13 *68169 1 Q.D. Pin Kit
*86723 1 O.D. Pin Kit (Some1000 RPM 1 3/4”) 14 64963 1 Cross Bearing Kit 15 68171 1 Yoke & Shaft Assy. 16 68172 1 Yoke 17 68173 1 Shaft, Splined 18 68711 1 Spring Dowel 19 68180 1 Shield Bearing 20 84729 1 Shield Kit (540 RPM & 1000 RPM 1-3/8”)
84726 1 Shield Kit (1000 RPM 1 3/4”)
QTY. DESCRIPTION
(540 RPM & 1000 RPM)
86723
Q.D. Pin Kit
*You must first determine which Q.D. Pin your drive­shaft requires before ordering the replacement. This applies to the 1000RPM Drivelines with the 1 3/4”-20 spline tractor yoke.
68169
Q.D. Pin Kit
46-5-1
Page 52
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
REF. PART
NO. NO.
QTY. DESCRIPTION
1 86552 1 Half Shaft (Tractor End) 540 RPM
86543 1 Half Shaft (Tractor End) 1000 RPM 1-3/8” 86730 1 Half Shaft (Tractor End) 1000 RPM 1-3/4”
2 86553 1 Half Shaft (Rear) 540 RPM
86544 1 Half Shaft (Rear) 1000 RPM 1-3/8” 86731 1 Half Shaft (Rear) 1000 RPM 1-3/4”
3 86554 1 Safety Guard (540 RPM)
86545 1 Safety Guard (1000 RPM 1-3/8”) 86732 1 Safety Guard (1000 RPM 1-3/4”)
4 93699 1 Q.D. Hub & Snap Ring (540 & 1000 - 1-3/8”)
86724 1 Q.D. Hub & Snap Ring (1000 1-3/4”)
5 63945 2 Q.D. Pin Kit (540 RPM)
86519 2 Q.D. Pin Kit (1000 RPM 1-3/8”) 86723 2 Q.D. Pin Kit (1000 RPM 1-3/4”)
6 93574 1 Yoke 1-3/8” - 6 Spline (540 RPM)
93575 1 Yoke 1-3/8” - 21 Spline (1000 RPM)
93580 1 Yoke 1-3/4” - 20 Spline (1000 RPM) 7 63956 3 Grease Fitting 45° 8 86529 2 Cross Bearing Kit (540 RPM)
86511 2 Cross Bearing Kit (1000 RPM) 9 86530 1 C.V. Central Body (540 RPM)
86512 1 C.V. Central Body (1000 RPM)
10 63956 1 Grease Fitting 11 86531 1 Yoke (Outer Tube) 540 RPM
86513 1 Yoke (Outer Tube) 1000 RPM
12 67108 1 Flexible Pin (540 RPM)
66866 1 Flexible Pin (1000 RPM)
13 86555 1 Tube, Outer 540 RPM
86541 1 Tube, Outer 1000 RPM 1-3/8”
86728 1 Tube, Outer 1000 RPM 1-3/4”
REF. PART
NO. NO.
QTY. DESCRIPTION
14 78608 1 Danger Decal 15 86534 1 Plastic Ring (540 RPM)
86331 1 Plastic Ring (1000 RPM) 16 86330 1 Grease Nipple 17 86754 1 Complete CV Shell (540 RPM)
86753 1 Complete CV Shell (1000 RPM) 18 86535 1 Ring Nut (540 RPM)
86517 1 Ring Nut (1000 RPM) 19 68179 1 Outer Shield Bearing (540 RPM)
66875 1 Outer Shield Bearing (1000 RPM) 20 64814 2 Chain 21 85414 1 Yoke (540 RPM)
86546 1 Yoke (1000 RPM) 22 50053705 1 Taper Pin Kit 23 44232BH 1 Hex Nut M14 x 2 24 44233BH 1 Lockwasher M14 25 64963 1 Cross Bearing (540 RPM)
64663 1 Cross Bearing (1000 RPM) 26 67086 1 Inner Tube Yoke (540 RPM)
66870 1 Inner Tube Yoke (1000 RPM) 27 67085 1 Flexible Pin (540 RPM)
66869 1 Flexible Pin (1000 RPM) 28 68180 1 Inner Shield Bearing (540 RPM)
66876 1 Inner Shield Bearing (1000 RPM) 29 78786 1 Danger Decal 30 86556 1 Inner Tube (540 RPM)
92961 1 Inner Tube (1000 RPM 1-3/8”)
92962 1 Inner Tube (1000 RPM 1-3/4”) 31 93699 1 Sleeve & Ball Kit, 1-3/8”
93700 1 Sleeve & Ball Kit, 1-3/4”
46-5-2
85006 80° C.V. DRIVESHAFT
Mfd. by Bondioli & Pavesi
540 RPM 1-3/8” – 6 Spline Tractor Yoke
Pull Models 3209, 3210, 3214, 3209-O, 3210-O
Serial Numbers 12-09999 and Below
Replaced by 76625SP (Mfd. by Comer / EG)
84998 80° C.V. DRIVESHAFT
Mfd. by Bondioli & Pavesi
1000 RPM, 1-3/8” - 21 Spline Tractor Yoke
Pull Models 13209, 13210, 3214
Serial Numbers 12-09999 and Below
Replaced by 76624SP (Mfd. by Comer / EG)
84999 80° C.V. DRIVESHAFT
Mfd. by Bondioli & Pavesi
1000 RPM 1-3/4” - 20 Spline Tractor Yoke
Pull Models 13209, 13210, 13214
Serial Numbers 12-09999 and Below
Replaced by 50024435 (Mfd. by Comer / EG)
SEPTEMBER, 2011
Page 53
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
86580 DRIVESHAFT ASSEMBLY
(540 RPM, 1-3/8” - 6 Spline Tractor Yoke)
Mfd. by Bondioli & Pavesi
For: Lift and Semi-Mount Models
3209, 3209 Offset, 3210, 3210 Offset, 3214
Serial Numbers 12-09999 and Below
May substitute 76729SP Driveshaft
86575 DRIVESHAFT ASSEMBLY
(1000 RPM, 1-3/8” - 21 Spline Tractor Yoke)
Mfd. by Bondioli & Pavesi
For: Lift & Semi-Mount Models
13209, 13210, 13214
Serial Numbers 12-09999 and Below
May substitute 76730SP Driveshaft
86591 DRIVESHAFT ASSEMBLY
(1000 RPM, 1-3/4” - 20 Spline Tractor Yoke)
Mfd. by Bondioli & Pavesi
For: Lift & Semi-Mount Models
13209, 13210, 13214
Serial Numbers 12-09999 and Below
May substitute 76731SP Driveshaft
REF. PART
NO. NO.
QTY. DESCRIPTION
1 86627 1 Inner Half w/Shield 86580, 86575)
86628 1 Inner Half w/Shield (86591)
2 78146 1 Outer Half w/Shield (86575)
78138 1 Outer Half w/Shield (86580) 82328 1 Outer Half w/Shield (86591)
3 78139 1 Safety Guard Assy. (86580, 86575)
82327 1 Safety Guard Assy. (86591) 4 86573 1 Torque Limiter Assy. 5 91564 1 Torque Limiter Repair Kit 6 78190 2 Q.D. Pin Kit (86575 Assy.)
63945 2 Q.D. Pin Kit (86580 Assy.)
86723 2 Q.D. Pin Kit (86591 Assy.) 7 78189 1 Tractor Yoke 1-3/8” - 21 Spline
64973 1 Tractor Yoke 1-3/8” - 6 Spline
68170 1 Tractor Yoke 1-3/4” - 20 Spline 8 64963 2 Cross Bearing Kit 9 63956 2 Grease Fitting
10 78136 1 Outer Yoke & Tube
(86575, 86580 Assy.)
82330 1 Outer Yoke & Tube (86591 Assy.)
11 67108 1 Spring Dowell 12 78134 1 Yoke, Outer Tube 13 78133 1 Outer Tube (86575, 86580 Assy.)
86607 1 Outer Tube (86591 Assy.)
14 78786 1 Danger Decal
REF. PART
NO. NO.
QTY. DESCRIPTION
15 67086 1 Inner Tube Yoke 16 67085 1 Spring Dowell 17 78132 1 Inner Tube (86575, 86580 Assy.)
86608 1 Inner Tube (86591 Assy.)
18 78135 1 Inner Tube & Tube Assy.
(86575, 85680 Assy.)
82331 1 Inner Yoke & Tube Assy. (86591 Assy.) 19 44159BH 8 Capscrew M10 x 1.5 x 100 Gr. 8.8 20 64641 1 Pressure Plate 21 64642 1 Inner Plate 22 86574 1 Brake Lining Support w/Pivot 23 50053705 1 Taper Pin Kit 24 44233BH 1 Lockwasher M14 25 44234BH 1 Hex Nut M14 26 64642 1 Inner Plate 27 64986 1 Intermediate Brake Lining 28 64828 1 Collar 29 64992 1 Flange Yoke 30 44154BH 8 Locknut M10 x 1.5 31 78608 1 Safety Decal 32 68179 1 Outer Guard Bearing 33 68180 1 Inner Guard Bearing 34 64657 8 Spring 35 91560 4 Lining
46-5-3
35
35
35
34
SEPTEMBER, 2011
Page 54
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
REF. PART
NO. NO.
QTY. DESCRIPTION
1 86629 1 Shielded Inner Half
2 64963 1 Cross Bearing Kit 3 63956 1 Grease Fitting 4 78165 1 Inner Yoke & Tube 5 78164 1 Inner Tube 6 67085 1 Roll Pin 7 67086 1 Yoke for Inner Tube 8 86573 1 Torque Limiter Assy.
9 64992 1 Flanged Yoke 10 64828 1 Collar 11 91564 1 Lining Kit 12 64986 1 Intermediate Brake Lining 13 64642 1 Inner Plate 14 86574 1 Brake Lining Support w/Pivot 15 50053705 1 Taper Pin Kit 16 44392BH 1 Hex Nut M14 x 2
REF. PART
NO. NO.
QTY. DESCRIPTION
17 44233BH 1 Lockwasher M14 18 64642 1 Inner Plate 19 64641 1 Pressure Plate 20 44154BH 8 Locknut M10 x 1.5 21 44159BH 8 Bolt M10 x 1.5 x 100 22 68180 1 Inner Guard Collar 23 64657 8 Spring 24 91560 4 Lining
25 78167 1 Shielded Outer Half Assy.
26 67098 1 Outer Shield Collar 27 68179 1 Outer Collar Sleeve 28 78786 1 Danger Decal 29 78608 1 Safety Decal
30 78168 1 Safety Guard Assy.
31 68166 1 Chain
46-5-4
86588 JACKSHAFT ASSEMBLY
For Models: 3209, 3209-O, 3210, 3210-O, 3214
Serial Numbers 12-09999 and Below
Mfd. by Bondioli & Pavesi
Replaced by 76410 Jackshaft
Mfd. by EG
24
24
24
24
28
29
27
26
25
30
31
23
SEPTEMBER, 2011
Page 55
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
REF. PART
NO. NO.
QTY. DESCRIPTION
69302 1 Cross Shaft Assy
1 79352 1 Yoke 2 64663 2 Cross Bearing Kit 3 63956 2 Grease Fitting 4 78148 1 Double Flanged Yoke 5 78119 1 Elastic Cushion Coupling 6 78118 2 Pin 7 78117 1 Flanged Yoke 8 78116 4 Elastic Cushion
9 78115 1 Yoke 10 79354 1 Q.D. Pin Kit 11 78114 1 Retaining Ring
REF. PART
NO. NO.
QTY. DESCRIPTION
69303 1 Cross Shaft Assy
1 64671 1 Q.D. Yoke Assy. 2 63945 1 Q.D. Pin Kit 3 82398 2 Cross Bearing Kit 4 82397 2 Grease Fitting 5 79358 2 Yoke for Splined Shaft 6 79353 1 Splined Shaft 7 68174 1 Pin 8 78119 1 Elastic Cushion Coupling
9 78118 2 Pin 10 78117 1 Flanged Yoke 11 78116 4 Elastic Cushion 12 78115 1 Yoke 13 78114 1 Retaining Ring 14 79354 1 Q.D. Pin Kit
69302 CROSS SHAFT ASSEMBLY
540 RPM & 1000 RPM – 1-3/8” – 21 Spline
For: Models 3209 & 13209
Serial Numbers 12-09999 and Below
69303 CROSS SHAFT ASSEMBLY
540 RPM & 1000 RPM –1-3/8” – 21 Spline
For: Models 3210 & 13210
Serial Numbers 12-09999 and Below
46-5-5
14
SEPTEMBER, 2011
Page 56
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-5-6
REF. PART
NO. NO.
QTY. DESCRIPTION
95740 1 Cross Shaft Assy
1 96855 1 Inner Half Assy. 2 96854 1 Joint 3 90938 2 Tapered Pin Kit 4 64663 2 Cross Bearing Kit 5 63956 2 Grease Fitting 6 66870 1 Inner Tube Yoke 7 66869 1 Flexible Pin 8 78120 1 Inner Tube
9 91568 1 Outer Half Assy. 10 91565 1 Yoke 11 66865 1 Outer Tube Yoke 12 66866 1 Flexible Pin 13 91566 1 Outer Tube 14 78786 1 Danger Decal
95740 CROSS SHAFT ASSEMBLY
(STANDARD)
Models 3209-Offset, 3210-Offset, 3214, 13214
Serial Numbers 12-09999 and Below
Mfd. by Bondioli & Pavesi
3
2
4
5
6
7
8
11
12
14
13
1
9
5
4
3
10
SEPTEMBER, 2011
Page 57
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
2
1
5
14
7
6
15
9
17
16
11
13
12
11
3
10
9
8
6
7
5
4
REF. PART
NO. NO.
QTY. DESCRIPTION
1 92875 1 Half Shaft 2 92876 1 Half Shaft 3 92877 1 Safety Shield 4 92871 1 Yoke 5 90938 2 Q.D. Pin Kit 6 63946 2 Grease Fitting 7 91266 2 Cross Bearing Kit 8 91267 1 Inner Tube Yoke
9 66866 2 Flexible Pin 10 92872 1 Inner Tube 11 91272 1 Ring Nut 12 78608 1 Safety Decal 13 64814 1 Complete Chains 14 92874 1 Joint 15 91270 1 Outer Tube Yoke 16 92873 1 Outer Tube 17 78786 1 Danger Decal
46-5-7
90511 HEAVY DUTY CROSS SHAFT
Models 3214, 13214
Replaced by 50058059 Cross Shaft
SEPTEMBER, 2011
Page 58
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
REF. PART
NO. NO.
QTY. DESCRIPTION
1 90352 1 Mount Weld. 2 88100 1 Shield Weld. 3 90356 1 Pin Weld. 4 –––– 2 Capscrew 1/2” x 1 1/4” Gr.5 5 –––– 1 Lockwasher 3/4” 6 9162400 1 Locknut 3/4” 7 –––– 2 Lockwasher 1/2” 8 20763 2 Capscrew 5/8” x 5” Gr.5
9 20237BH 2 Capscrew 5/8” x 4” Gr.5 10 19486 4 Lockwasher 5/8” 11 9162000 4 Locknut 5/8” 12 90986 1 Pillow Block Bearing 13 88916 2 Bushing, Tension 14 77492 1 Snap Ring 15 77491 1 Bearing w/ Collar 16 88840 1 Set Screw 17 90983 1 Spacer
46-5-8
PILLOW BLOCK BEARING & MOUNT
FOR ALL PULL MODELS
3200 SERIES
4
7
2
17
13
13
15
16
14
12
3
1
5
6
8
9
10
11
10
11
SEPTEMBER, 2011
Page 59
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-5-9
REF. PART
NO. NO.
QTY. DESCRIPTION
76405 1 Driveline Assy 76406 1 Driveline Assy 76412 1 Driveline Assy
1 76248 1 Push Pin Yoke (76405)
76494 1 Push Pin Yoke (76412)
76481 1 Push Pin Yoke (76406) 2 64963 2 Cross Journal Set 3 63956 2 Grease Nipple 4 76479 1 Yoke w/ Sleeve Assy. (76405, 76412)
76486 1 Yoke w/ Sleeve Assy. (76406) 5 76335 1 Grease Nipple 6 76480 1 Splined Shaft 7 66866 1 Roll Pin for Inner Tube 8 68172 1 Inner Yoke 9 76481 1 Push Pin Yoke (76405, 76412)
76481 2 Push Pin Yoke (76406)
10 76244 1 Guard Retaining Collar, Outer 11 87992 6 Bolt 12 76245 1 Guard Retaining Collar, Inner 13 64814 2 Safety Chain 14 76482 1 Complete Shield w/ Instr. (76405)
76487 1 Complete Shield w/ Instr. (76406)
15 76062 2 Push Pin Set, 1-3/8” (76405, 76412) 16 76483 2 Push Pin Set, 1-3/4” (76405, 76412)
76483 4 Push Pin Set, 1-3/4” (76406)
17 76484 1 Half Female Shaft w/ Shield (76405)
76488 1 Half Female Shaft w/ Shield (76406)
76501 1 Half Female Shaft w/ Shield (76412)
18 76485 1 Half Male Shaft w/ Shield (76405, 76412)
76489 1 Half Male Shaft w/ Shield (76406)
19 78786 1 Danger Decal, Outer Tube 20 78608 1 Danger Decal, Outer Shield
76405 DRIVESHAFT
540 RPM – 1-3/8” – 6 Spline
Mfd. by Comer / EG
Used on All Pull Models
3209, 3210, 3214
76406 DRIVESHAFT
1000 RPM – 1-3/4” – 20 Spline
Mfd. by Comer / EG
Used on All Pull Models
3209, 3210, 3214
76412 DRIVESHAFT
1000 RPM – 1-3/8” – 21 Spline
Mfd. by Comer / EG
Used on All Pull Models
3209, 3210, 3214
15
19
5
10
11
11
13
12
20
2
9
16
8
7
6
1
3
2
4
3
17
18
14
SEPTEMBER, 2011
Page 60
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-5-10
REF. PART
NO. NO.
QTY. DESCRIPTION
76729SP 1 Driveline Assy 76730SP 1 Driveline Assy 76731SP 1 Driveline Assy
1 76803 1 Complete Collar Yoke (76729SP)
76805 1 Complete Collar Yoke (76730SP)
76806 1 Complete Collar Yoke (76731SP) 2 64963 2 Cross Journal Set 3 63956 2 Grease Nipple 4 78134 1 Outer Yoke 5 67108 1 Roll Pin for Outer Tube 6 78133 1 Outer Tube (76729SP, 76730SP)
86607 1 Outer Tube (76731SP) 7 78132 1 Inner Tube (76729SP, 76730SP)
86608 1 Inner Tube (76731SP) 8 67085 1 Roll Pin for Inner Tube 9 67086 1 Inner Yoke
10 76490 1 Complete Disc Clutch 11 76244 1 Guard Retaining Collar, Outer 12 87992 6 Bolt 13 76245 1 Guard Retaining Collar, Inner 14 64814 2 Safety Chain
REF. PART
NO. NO.
QTY. DESCRIPTION
15 76491 1 Complete Shield w/ Instr.
(76729SP, 76730SP)
76496 1 Complete Shield w/ Instr. (76731SP)
16 50017480 1 Ball Collar Kit 1-3/8” (76729SP, 76730SP)
50017502 1 Ball Collar Kit 1-3/4” (76731SP) 17 76080 8 Spring 18 76331 1 Flanged Yoke 19 76082 1 Bushing 20 76083 4 Lining Ring 21 76247 1 Tapered Pin Set 1-3/4” 22 76458 1 Clutch Support 23 76085 2 Inner Plate 24 76197 1 Intermediate Plate 25 76086 1 Pressure Plate 26 44159BH 8 Capscrew M10 x 1.5 x 100 27 44154BH 8 Lock Nut M10 x 1.5 28 76815 1 Half Female Shaft w/ Shield (76729SP)
76816 1 Half Female Shaft w/ Shield (76730SP) 76836 1 Half Female Shaft w/ Shield (76731SP)
29 76493 1 Half Male Shaft w/ Shield
(76729SP, 76730SP)
76498 1 Half Male Shaft w/ Shield (76731SP) 30 78786 1 Danger Decal, Outer Tube 31 78608 1 Danger Decal, Outer Shield
76729SP DRIVESHAFT
Mfd. by Comer / EG
540 RPM – 1-3/8” – 6 Spline
Used on All Lift & Semi-Mount Models
3209, 3209-Offset, 3210, 3210 Offset, 3214
Replaces 76407 Driveshaft.
76730SP DRIVESHAFT
Mfd. by Comer / EG
1000 RPM – 1-3/8” – 21 Spline
Used on All Lift & Semi-Mount Models 13209, 13210, 13214
Replaces 76408 Driveshaft.
76731SP DRIVESHAFT
Mfd. by Comer / EG
1000 RPM – 1-3/4” – 20 Spline
Used on All Lift & Semi-Mount Models 13209, 13210, 13214
Replaces 76409 Driveshaft.
27
17
18
19
20
21
20
22
2
4
5
11
31
14
12
12
6
7
30
23
20
24
20
23
25
26
2
9
13
8
3
1
3
15
29
28
10
16
Note: Some early driveshafts were shipped with push pins on the tractor yoke end. Order 76062 push pin set to replace pin (76407, 76408 Driveshafts), or 76483 push pin set (76409 Driveshaft). For complete yoke replacement, order Collar Yoke (See Ref. No.1).
Push Pin Set
SEPTEMBER, 2011
Page 61
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
SEPTEMBER, 2011
13
1
14
8
15
17
16
2
3
16
4
9
15
5
24
25
19
16
6
18
27
26
11
16
7
20
21
22
23
10
9
76410 JACKSHAFT (540 rpm)
Mfd. by Comer / EG
Used on 3200 Series Models with Serial Numbers 12-09999 and Below
REF. PART
NO. NO.
76410 1 Jackshaft Assy
1 76490 1 Complete Disc Clutch 2 64963 1 Cross Journal Set 3 63956 1 Grease Nipple 4 78134 1 Outer Yoke 5 67108 1 Roll Pin for Outer Tube 6 76502 1 Outer Tube 7 76499 1 Inner Tube w/ Splined Shaft 8 76244 1 Guard Retaining Collar, Outer
9 87992 6 Bolt 10 76245 1 Guard Retaining Collar, Inner 11 64814 2 Safety Chain 12 76500 1 Complete Shield w/ Instr. 13 44159BH 8 Capscrew M10 x 1.5 x 100
QTY. DESCRIPTION
12
REF. PART
NO. NO.
14 76086 1 Pressure Plate 15 76085 2 Inner Plate 16 76083 4 Lining Ring 17 76197 1 Intermediate Plate 18 76458 1 Clutch Support 19 76247 1 Tapered Pin Set 1-3/4” 20 76082 1 Bushing 21 76331 1 Flanged Yoke 22 76080 8 Spring 23 44154BH 8 Lock Nut M10 x 1.5 24 78786 1 Danger Decal, Outer Tube 25 78608 1 Danger Decal, Outer Shield
*26 50021244 1 Jackshaft Extension, 3210 *27 50021245 1 Jackshaft Extension, 3214
QTY. DESCRIPTION
*Note: Jackshaft Extensions are not included in the 76410 Jackshaft Assembly
46-5-11
Page 62
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-5-12
REF. PART
NO. NO.
QTY. DESCRIPTION
96493 1 Cross Shaft Assy
1 561 1 Yoke 1-3/8” – 21 Spline 2 595BH 2 Cross & Bearing Kit 3 96494 1 Yoke & Bar Assembly 4 96495 1 Sleeve, Tube & Yoke Assembly
5 96496 1 Shearbolt Clutch (Items 6 – 12)
6 19044 2 Capscrew 1/2” x 2-3/4” Gr.5 7 8151600 2 Hex Nut 1/2” 8 –––– 1 Shear Yoke & Hub
9 –––– 24 Ball 10 –––– 1 Grease Zerk 11 96498 1 Q.D. Pin Kit 12 15806 1 Lockwasher 13 50020354 1 Shear Bolt Repair Kit 14 78786 1 Decal
96493 CROSS SHAFT
Manufactured by Walterscheid
Model: 3214 (13214SS1)
Serial Numbers 12-09999 and Below
1
7
12
6
3
14
4
6
10
13
11
9
7
8
2
2
5
SEPTEMBER, 2011
Page 63
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-5-13
76232 C.V. Driveshaft
540 RPM – 1-3/8” – 6 Spline
(Mfd. by Comer / EG)
Used on All Pull Models
3209, 3210, 3214
Serial Numbers 12-09999 and Below
Replaced by 76625SP Driveshaft
(Mfd. by Comer / EG)
76233 C.V. DRIVESHAFT
1000 RPM – 1-3/8” – 21 Spline
(Mfd. by Comer / EG)
Used on All Pull Models
3209, 3210, 3214
3209–O, 3210–O
Serial Numbers 12-09999 and Below
Replaced by 76624SP Driveshaft
(Mfd. by Comer / EG)
76571 C.V. DRIVESHAFT
1000 RPM – 1-3/4” – 20 Spline
(Mfd. by Comer / EG)
Used on All Pull Models
3209, 3210, 3214
Serial Numbers 12-09999 and Below
Replaced by 50024435 Driveshaft
(Mfd. by Comer / EG)
22
1
3
2
2
7
9
10
10
21
12
11
5
15
20
4
3
16
17
4
8
13
14
18
19
6
REF. PART
NO. NO. QTY. DESCRIPTION
1 50017482 1 Complete Collar Yoke (76233)
50017501 1 Complete Collar Yoke (76571) 50017504 1 Complete Collar Yoke (76232)
2 76420 2 Cross Journal Set (76233,76571)
76356 2 Cross Journal Set (76232)
3 63956 3 Grease Nipple (76232, 76233)
76579 2 Grease Nipple (76571)
4 76421 1 Wide Angle Double Yoke (76233, 76571)
76357 1 Wide Angle Double Yoke (76232)
5 64663 1 Cross Journal Set (76233)
64963 1 Cross Journal Set (76232) 76582 1 Cross Journal Set (76571)
6 76422 1 Complete Yoke (76233, 76571)
76239BH 1 Complete Yoke (76232) 7 76362 6 Screw 8 76423 1 Bearing Ring (76233, 76571)
76363 1 Bearing Ring (76232)
9 76057 1 Guard Retaining Collar,
Outer (76233,76571)
76244 1 Guard Retaining Collar,
Outer (76232) 10 87992 6 Bolt 11 76059 1 Guard Retaining Collar,
Inner (76233, 76571)
76245 1 Guard Retaining Collar,
Inner (76232)
REF. PART
NO. NO. QTY. DESCRIPTION
12 64814 3 Safety Chain 13 76424 1 Guard Cone Set (76233,76571)
76950 1 Guard Cone Set (76232)
14 76450 1 Complete Shield w/ Instr.(76233)
76599 1 Complete Shield w/ Instr.(76571)
76433 1 Complete Shield w/ Instr. (76232) 15 76247 1 Tapered Pin Set 1-3/4” 16 76451 1 Female Tube w/ Yoke and Lube (76233)
76600 1 Female Tube w/ Yoke and Lube (76571)
76442 1 Female Tube w/ Yoke and Lube (76232) 17 76452 1 Male Tube w/ Yoke and Lube (76233)
76601 1 Male Tube w/ Yoke and Lube (76571)
76447 1 Male Tube w/ Yoke and Lube (76232) 18 76453 1 Half Female Shaft w/ Shield (76233)
76602 1 Half Female Shaft w/ Shield (76571)
76448 1 Half Female Shaft w/ Shield (76232) 19 76454 1 Half Male Shaft w/ Shield (76233)
76603 1 Half Male Shaft w/ Shield (76571)
76449 1 Half Male Shaft w/ Shield (76232) 20 78786 1 Danger Decal, Outer Tube 21 78608 1 Danger Decal, Outer Shield 22 50017480 1 Ball Collar Kit, 1-3/8” (76232, 76233)
50017502 1 Ball Collar Kit, 1-3/4” (76571)
SEPTEMBER, 2011
Page 64
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-5-14
76567 CROSS SHAFT
Manufactured by Comer / EG
Used on Models 3209 & 13209
Serial Numbers 12-10000 and Above
Replaced by 50023262 Cross Shaft
76568 CROSS SHAFT
Manufactured by Comer / EG Used on Model 3210 & 13210
Serial Numbers 12-10000 and Above
Replaced by 50034818 Cross Shaft & 50036647 Shield Kit
REF. PART
NO. NO.
QTY. DESCRIPTION
1 76700 1 Yoke 2 76696 2 Cross Journal Set 3 –––– 8 Circlip 4 76783 2 Grease Nipple 5 76701 1 Double Flanged Yoke 6 76702 1 Special Rubber Element, Complete 7 –––– 1 Bolt & Nut
REF. PART
NO. NO.
QTY. DESCRIPTION
1 76695 1 Yoke 2 76696 2 Cross Journal Set 3 –––– 8 Circlip 4 76783 2 Grease Nipple 5 76698 1 Double Flanged Yoke 6 76699 1 Special Rubber Element, Complete 7 –––– 1 Grease Nipple 8 76247 1 Tapered Pin Set 1-3/4”
7
3
4
5
6
1
2
3
4
2
3
4
5
7
2
3
4
8
2
1
6
SEPTEMBER, 2011
Page 65
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-5-15
REF. PART
NO. NO.
QTY. DESCRIPTION
1 76239BH 1 Complete Yoke 2 64963 2 Cross Journal Set 3 –––– 8 Circlip 4 63956 2 Grease Nipple 5 76703 1 Inner Tube (76569)
76708 1 Inner Tube (76626) 6 67085 1 Roll Pin for Inner Tube 7 67086 1 Inner Yoke 8 76704 1 Complete Rubber Element 9 –––– 1 Yoke
10 76247 2 Tapered Pin Set 1-3/4” 11 –––– 1 Female Tube Yoke 12 –––– 1 Male Tube Yoke 13 76705 1 Half Female Shaft (76569)
76709 1 Half Female Shaft (76626)
14 76706 1 Half Male Shaft (76569)
76710 1 Half Male Shaft (76626)
15 78786 1 Danger Decal
*76569 CROSS SHAFT
Manufactured by Comer / EG
For 3209 Offset with Serial Numbers 12-10000 and Above
*For replacement of this driveshaft, order 50035303 Cross Shaft & 50035715 Shield Kit
*76626 CROSS SHAFT
Manufactured by Comer / EG
For 3210 Offset with Serial Numbers 12-10000 and Above
*For replacement of this driveshaft, order 50035303 Cross Shaft & 50035716 Shield Kit
10
9
1
15
5
6
7
3
4
10
2
11
2
8
4
3
13
12
14
SEPTEMBER, 2011
Page 66
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-5-16
REF. PART
NO. NO.
QTY. DESCRIPTION
76624SP 1 C.V. Driveshaft Assy
50024435 1 C.V. Driveshaft Assy
1 50017482 1 Complete Collar Yoke (76624SP)
50017501 1 Complete Collar Yoke (50024435) 2 76420 2 Cross Journal Set 3 76579 3 Grease Nipple 4 76421 1 Wide Angle Double Yoke 5 76893 1 Outer Yoke 6 66866 1 Roll Pin for Outer Tube 7 76894 1 Wiper 8 76901 1 Outer Tube w/ Decal (76624SP)
76900 1 Outer Tube w/ Decal (50024435)
9 64663 1 Cross Journal Set
10 76422 1 Complete Yoke 11 76362 6 Screw Kit 12 76423 1 Bearing Ring 13 76057 1 Collar, Outer Tube 14 87992 6 Bolt 15 76059 1 Collar, Inner Tube
REF. PART
NO. NO.
QTY. DESCRIPTION
16 64814 3 Safety Chain 17 76933 1 Guard Cone Set 18 76948 1 Complete Shield (76624SP)
76957 1 Complete Shield (50024435) 19 76247 1 Tapered Pin Set 1-3/4” 20 76681 1 Female Tube w/ Yoke & Lube 21 76682 1 Male Tube w/ Yoke & Lube 22 76949 1 Half Female Shaft
w/ Shield (76624SP)
76958 1 Half Female Shaft
w/ Shield (50024435) 23 76684 1 Half Male Shaft w/ Shield 24 78786 1 Danger Decal, Outer Tube 25 78608 1 Danger Decal, Outer Shield 26 76892 1 Plastic Cap, Outer Tube 27 50017480 1 Ball Collar Kit 1-3/8” (76624SP)
50017502 1 Ball Collar Kit 1-3/4” (50024435)
76624SP C.V. DRIVESHAFT ASSEMBLY
1000 RPM – 1-3/8” – 21 Spline
ASAE Size 4
Manufactured by Comer / EG
Used on Pull Models 13209, 13210
Serial Numbers 12-10000 and Above
Replaces 76233 Driveshaft
50024435 C.V. DRIVESHAFT ASSEMBLY
1000 RPM – 1-3/4” – 20 Spline
ASAE Size 4
Manufactured by Comer / EG
Used on Pull Models 13209, 13210
Serial Numbers 12-10000 and Above
Replaces 76571 Driveshaft
27
1
2
4
8
26
6
10
20
21
19
3
2
3
9
3
11
17
13
14
14
15
16
25
12
18
22
23
24
5
7
SEPTEMBER, 2011
Page 67
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-5-17
REF. PART
NO. NO.
QTY. DESCRIPTION
76625SP 1 C.V. Driveshaft Assy
1 50017504 1 Complete Collar Yoke 2 76356 2 Cross Journal Set 3 76579 3 Grease Nipple 4 76357 1 Wide Angle Double Yoke 5 76896 1 Outer Yoke 6 67108 1 Roll Pin, Outer Tube 7 76897 1 Wiper 8 76902 1 Outer Tube w/ Decal
9 76604 1 Cross Journal Set 10 76239BH 1 Complete Yoke 11 76362 6 Screw Kit 12 76363 1 Bearing Ring 13 76244 1 Collar, Outer Tube 14 87992 6 Bolt
REF. PART
NO. NO.
QTY. DESCRIPTION
15 76245 1 Collar, Inner Tube 16 64814 3 Safety Chain 17 76950 1 Guard Cone Set 18 76951 1 Complete Guard 19 76247 1 Tapered Pin Set 1-3/4” 20 76687 1 Female Tube w/ Yoke & Lube 21 76688 1 Male Tube w/ Yoke & Lube 22 76952 1 Half Female Shaft w/ Guarding 23 76690 1 Half Male Shaft w/ Guarding 24 78786 1 Danger Decal, Outer Tube 25 78608 1 Danger Decal, Outer Guard Tube 26 76899 1 Plastic Cap, Outer Tube 27 50017480 1 Ball Collar Kit 1-3/8”
76625SP C.V. DRIVESHAFT ASSEMBLY
540 RPM – 1-3/8” – 6 Spline
ASAE Size 5
Manufactured by Comer / EG
Used on Pull Models 3209 & 3209 Offset, 3210 & 3210 Offset Serial Numbers 12-10000 and Above
Replaces 76232 & 85006 Driveshafts
27
1
2
4
8
26
6
10
20
21
19
3
2
3
9
3
11
17
13
14
14
15
16
25
12
18
22
23
24
5
7
SEPTEMBER, 2011
Page 68
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-5-18
76627 JACKSHAFT ASSEMBLY
Manufactured by Comer / EG
Used on Pull Models 3209 & 3209 Offset
With Serial Numbers 12-10000 and Above
76629 JACKSHAFT ASSEMBLY
Manufactured by Comer / EG
Used on Model 3210
With Serial Numbers 12-10000 and Above
REF. PART
NO. NO.
QTY. DESCRIPTION
76627 1 Jackshaft Assy 76629 1 Jackshaft Assy
1 76490 1 Complete Disc Clutch 2 64963 1 Cross Journal Set 3 63956 1 Grease Nipple 4 78134 1 Outer Yoke 5 67108 1 Roll Pin for Outer Tube 6 76693 1 Outer Tube w/ Splined Shaft (76627)
76691 1 Outer Tube w/ Splined Shaft (76629) 7 76244 1 Guard Retaining Collar 8 87992 6 Bolt 9 76245 1 Guard Retaining Collar
10 64814 2 Safety Chain 11 76694 1 Complete Shield (76627)
76692 1 Complete Shield (76629)
REF. PART
NO. NO.
QTY. DESCRIPTION
12 44159BH 8 Bolt M10 x 100 13 78086 1 Pressure Plate 14 76085 2 Inner Plate 15 76083 4 Lining Ring 16 76197 1 Intermediate Plate 17 76458 1 Clutch Support 18 76247 1 Tapered Pin Set 1-3/4” 19 76082 1 Bushing 20 76331 1 Flanged Yoke 21 76080 8 Spring 22 78786 1 Danger Decal, Outer Tube 23 78608 1 Danger Decal, Outer Shield Tube 24 44154BH 8 Lock Nut M10
12
13
14
14
15
16
15 15
15
19
20
21
24
18
17
3
2
4
6
5
22
7
8
10
23
9
11
1
SEPTEMBER, 2011
Page 69
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
SEPTEMBER, 2011
1
6
7
8
2
4
3
2
4
5
50023262 RUBBER ELEMENT CROSS SHAFT
Manufactured by Bondioli & Pavesi
Used on Models 3209 & 13209 S/N 12-10000 and Above
Replaces 76567 Cross Shaft (Mfd. by Comer / EG)
REF. PART
NO. NO.
50023262 1 Rubber Element Cross Shaft Assy
1 50034928 1 Yoke 2 68987 2 Cross Journal Assembly 3 50034929 1 Yoke 4 63946 4 Grease Nipple 5 50034930 1 GE Joint 6 44427BH 1 Capscrew M12 x 1.75 x 75 G8.8 7 44269 1 Flatwasher M12 8 44244BH 1 Hex Nut M12
QTY. DESCRIPTION
1
4
2
4
3
2
4
5
6
*50023264 RUBBER ELEMENT CROSS SHAFT
Manufactured by Bondioli & Pavesi
Used on Models 3210 & 13210 S/N 12-10000 and Above
*To replace this driveshaft, order 50034818 Cross Shaft & 50036647 Shield Kit
REF. PART
NO. NO.
1 50034925 1 Yoke 2 68987 2 Cross Journal Assembly 3 50034926 1 Yoke 4 63946 4 Grease Nipple 5 50034927 1 Joint 6 50053705 1 Taper Pin Kit
QTY. DESCRIPTION
46-5-19
Page 70
BUSH HOG/ LAND MAINTENANCE REPAIR PARTS MANUAL
SEPTEMBER, 2011
11
1
2
3
4
12
7
9
6
5
8
13
2
3
11
4
10
50035303 CROSS SHAFT & 50035715 SHIELD KIT (3209 OFFSET) 50035303 CROSS SHAFT & 50035716 SHIELD KIT (3210 OFFSET)
Bondioli & Pavesi Series 8, ASAE Size 5
Used on 3209 Offset, 3210 Offset
Replaces 76569 & 76626 Cross Shafts (Comer / EG)
REF. PART
NO. NO.
50035303 1 Cross Shaft Assy 50035715 1 Shield Kit (3209 Offset) 50035716 1 Shield Kit (3210 Offset)
1 85414 1 Complete Yoke 2 68176 2 Cross Journal Set 3 –––– 8 Circlip 4 63946 2 Grease Nipple 5 50035693 1 Inner Tube 6 67085 1 Roll Pin for Inner Tube 7 50035694 1 Female Yoke & Tube 8 67086 1 Inner Tube Yoke
9 78786 1 Danger Decal 10 50035695 1 Joint 11 50053705 2 Taper Pin Kit 12 50035696 1 Half Female Shaft 13 50035697 1 Half Male Shaft
QTY. DESCRIPTION
46-5-20
Page 71
BUSH HOG/ LAND MAINTENANCE REPAIR PARTS MANUAL
46-5-21
REF. PART
NO. NO.
QTY. DESCRIPTION
50034818 1 Cross Shaft Assy 50036647 1 Shield Kit
1 50036672 1 Yoke 2 50036673 2 Cross Journal Assembly 3 –––– 8 Circlip 4 63946 3 Grease Nipple 5 50036674 1 Intermediate Yoke 6 50035695 1 Rubber Element 7 50053705 1 Taper Pin Kit
50034818 CROSS SHAFT & 50036647 SHIELD KIT
Bondioli & Pavesi Series DG8, ASAE Size 5
Used on Model 3210
Replaces 50023264 & 76568 Cross Shafts (Comer / EG)
5
6
7
4
4
1
2
4
3
2
3
SEPTEMBER, 2011
Page 72
BUSH HOG/ LAND MAINTENANCE REPAIR PARTS MANUAL
76841 CV DRIVESHAFT ASSEMBLY
540 RPM, 1-3/8” X 6 SPLINE TRACTOR YOKE
ASAE SIZE 5
MANUFACTURED BY BONDIOLI & PAVESI
Used On: 540 RPM Pull Models 3209, 3209-O, 3210, 3210-O, 3214
Replaced by 50053302SP (May Substitute 76625SP)
REF. PART
NO. NO.
QTY. DESCRIPTION
1 71390 1 Yoke, CV 1-3/8” -6 Spline (Tractor) 2 71391 2 Cross Bearing Kit 3 63946 4 Grease Fitting 4 71392 1 Yoke w/Hub, Outer Tube 5 71393 1 Central Body 6 71428 1 Outer Cardan Tube 7 71429 1 Inner Tube Assy. w/Lube Fitting 8 71396 1 Flexible Pin
9 71397 1 Flexible Pin 10 71398 1 Yoke, Inner Tube 11 71399 1 Cross Bearing Kit 12 71400 1 Tube Plug 13 71401 1 Yoke, 1-3/4”-20 Spline (Implement) 14 71440 1 Grease Fitting
REF. PART
NO. NO.
QTY. DESCRIPTION
15 71455 1 Outer Ring 16 71402 1 Ring for Inner Cone 17 71403 1 Ring 18 71404 17 Screw 19 71405 1 Chain 20 71447 1 Shield Tube Connecting Ring 21 78608 1 Danger Decal 22 78786 1 Danger Shield Missing 23 71406 1 Sleeve Kit 24 71407 1 Pivot 25 71430 1 Outer Half Shaft 26 71431 1 Inner Half Shaft 27 71432 1 Complete Guard Assembly
46-5-22
SEPTEMBER, 2011
Page 73
BUSH HOG/ LAND MAINTENANCE REPAIR PARTS MANUAL
76842 CV DRIVESHAFT ASSEMBLY
1000 RPM, 1-3/8”- 21 SPLINE TRACTOR YOKE
ASAE SIZE 4
MANUFACTURED BY BONDIOLI & PAVESI
Used On: 1000 RPM Pull Models 3209, 3210, 3214
Replaced by 50053301SP (May Substitute 76624SP)
REF. PART
NO. NO.
QTY. DESCRIPTION
1 71441 1 Yoke, CV 1-3/8” -21 Spline (Tractor)
2 71412 2 Cross Bearing Kit
3 63946 4 Grease Fitting
4 71413 1 Yoke w/Hub, Outer Tube
5 71414 1 Central Body
6 71442 1 Outer Cardan Tube
7 71443 1 Inner Tube Assy. w/Lube Fitting
8 66866 1 Flexible Pin
9 71418 1 Flexible Pin 10 71419 1 Yoke, Inner Tube 11 71420 1 Cross Bearing Kit 12 71421 1 Tube Plug 13 71422 1 Yoke, 1-3/4”-20 Spline (Implement) 14 71440 1 Grease Fitting
REF. PART
NO. NO.
QTY. DESCRIPTION
15 71448 1 Outer Ring 16 71402 1 Ring for Inner Cone 17 71438 1 Ring 18 71404 17 Screw 19 71405 1 Chain 20 71447 1 Shield Tube Connecting Ring 21 78608 1 Danger Decal 22 78786 1 Danger Shield Missing 23 50042833 1 Sleeve Kit 24 71407 1 Pivot 25 71444 1 Outer Half Shaft 26 71445 1 Inner Half Shaft 27 71446 1 Complete Guard Assembly
46-5-23
SEPTEMBER, 2011
Page 74
BUSH HOG/ LAND MAINTENANCE REPAIR PARTS MANUAL
76843 CV DRIVESHAFT ASSEMBLY
1000 RPM, 1-3/4”- 20 SPLINE TRACTOR YOKE
ASAE SIZE 4
MANUFACTURED BY BONDIOLI & PAVESI
Used On: 1000 RPM Pull Models 3209, 3210, 3214
Replaced by 50053300
REF. PART
NO. NO.
QTY. DESCRIPTION
1 71411 1 Yoke, CV 1-3/4” - 20 Spline (Tractor) 2 71412 2 Cross Bearing Kit 3 63946 4 Grease Fitting 4 71413 1 Yoke w/Hub, Outer Tube 5 71414 1 Central Body 6 71415 1 Outer Cardan Tube 7 71416 1 Inner Tube Assy. w/Lube Fitting 8 71417 1 Flexible Pin
9 71418 1 Flexible Pin 10 71419 1 Yoke, Inner Tube 11 71420 1 Cross Bearing Kit 12 71421 1 Tube Plug 13 71422 1 Yoke, 1-3/4”-20 Spline (Implement) 14 71440 1 Grease Fitting
REF. PART
NO. NO.
QTY. DESCRIPTION
15 71448 1 Outer Ring 16 71402 1 Ring for Inner Cone 17 71438 1 Ring 18 71404 17 Screw 19 71405 1 Chain 20 71447 1 Shield Tube Connecting Ring 21 78608 1 Danger Decal 22 78786 1 Danger Shield Missing 23 71423 1 Sleeve Kit 24 71407 1 Pivot 25 71425 1 Outer Half Shaft 26 71426 1 Inner Half Shaft 27 71427 1 Complete Guard Assembly
46-5-24
SEPTEMBER, 2011
Page 75
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
SEPTEMBER, 2011
24
13
2
14
20
21
26
18
9
19
14
18
17
5
1
14 16
4
3 6
12
11
7
8
10
25
15
22
1
50053300 CV DRIVESHAFT ASSEMBLY
1000 RPM, 1-3/4” – 20 Spline Tractor Yoke
Models: 1000 RPM Pull Models 3209, 3210, 3214
REF. PART
NO. NO.
50053300 1 C.V. Driveshaft Assy
1 50053720 1 Yoke, CV 1-3/4”, 20 Spline 2 50053718 1 Cross Bearing Kit 3 50053717 1 Yoke 4 50053716 1 Central Body 5 50053715 1 Roll Pin 6 50053714 1 Drive Tube, Outer 7 71418 1 Flexible Roll Pin, Inner 8 71419 1 Yoke, Inner Tube
9 50053713 1 Drive Tube, Inner 10 50053712 1 Yoke, 1-3/4”, 20 Spline 11 71420 1 Cross Bearing Kit 12 50053711 1 Shield Support, Outer 13 50053710 1 Shield Support
QTY. DESCRIPTION
ASAE Size 4
Mfd. by Bondioli & Pavesi
REF. PART
NO. NO.
14 71404 12 Screw, Self-Tapping 15 71402 1 Shield Support, Inner 16 50053709 6 Washer 17 71447 1 Single Chain Restraint Collar 18 50053708 2 Screw 19 50053707 1 Shield Chain 20 78786 1 Danger Decal, Outer Tube 21 78608 1 Danger Decal, Shield 22 50053706 1 Ball Collar Kit 1-3/4” 23 50053705 1 Taper Pin Kit, 3 Pins 24 50053704 1 Half Shaft, Outer, Shielded 25 50053703 1 Half Shaft, Inner, Shielded 26 50053702 1 Complete Shield
23
10
QTY. DESCRIPTION
46-5-25
Page 76
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
SEPTEMBER, 2011
24
13
2
14
20
21
26
18
9
19
14
18
17
5
1
14 16
4
3 6
12
11
7
8
10
25
15
22
1
50053301SP CV DRIVESHAFT ASSEMBLY
1000 RPM, 1-3/8” – 21 Spline Tractor Yoke
Models: 1000 RPM Pull Models 3209, 3210, 3214
May Substitute 76624SP (Comer)
REF. PART
NO. NO.
50053301SP 1 C.V. Driveline Assy
1 50053719 1 Yoke, CV 1-3/8”, 21 Spline 2 50053718 1 Cross Bearing Kit 3 50053717 1 Yoke 4 50053716 1 Central Body 5 50053715 1 Roll Pin 6 50053714 1 Drive Tube, Outer 7 71418 1 Flexible Roll Pin, Inner 8 71419 1 Yoke, Inner Tube
9 50053713 1 Drive Tube, Inner 10 50053712 1 Yoke, 1-3/4”, 20 Spline 11 71420 1 Cross Bearing Kit 12 50053711 1 Shield Support, Outer 13 50053710 1 Shield Support
QTY. DESCRIPTION
ASAE Size 4
Mfd. by Bondioli & Pavesi
REF. PART
NO. NO.
14 71404 12 Screw, Self-Tapping 15 71402 1 Shield Support, Inner 16 50053709 6 Washer 17 71447 1 Single Chain Restraint Collar 18 50053708 2 Screw 19 50053707 1 Shield Chain 20 78786 1 Danger Decal, Outer Tube 21 78608 1 Danger Decal, Shield 22 50053721 1 Ball Collar Kit 1-3/8” 23 50053705 1 Taper Pin Kit, 3 Pins 24 50053704 1 Half Shaft, Outer, Shielded 25 50053703 1 Half Shaft, Inner, Shielded 26 50053702 1 Complete Shield
23
10
QTY. DESCRIPTION
46-5-26
Page 77
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
SEPTEMBER, 2011
24
13
2
14
20
21
26
18
17
14
9
8
19
18
5
1
14
16
4
3 6
12
11
7
10
25
15
22
1
50053302SP CV DRIVESHAFT ASSEMBLY
1000 RPM, 1-3/8” – 6 Spline Tractor Yoke
Models: 540 RPM Pull Models 3209, 3209-O, 3210, 3210-O, 3214
May Substitute 76625SP (Comer)
REF. PART
NO. NO.
50053302SP 1 C.V. Driveline Assy
1 50053678 1 Yoke, CV 1-3/8”, 6 Spline 2 50053677 1 Cross Bearing Kit 3 50053728 1 Yoke 4 50053727 1 Central Body 5 50053715 1 Roll Pin 6 50053726 1 Drive Tube, Outer 7 71397 1 Flexible Roll Pin, Inner 8 71398 1 Yoke, Inner Tube
9 50053725 1 Drive Tube, Inner 10 50053723 1 Yoke, 1-3/4”, 20 Spline 11 71399 1 Cross Bearing Kit 12 50053711 1 Shield Support, Outer 13 50053722 1 Shield Support
QTY. DESCRIPTION
ASAE Size 5
Mfd. by Bondioli & Pavesi
REF. PART
NO. NO.
14 71404 12 Screw, Self-Tapping 15 71402 1 Shield Support, Inner 16 50053709 6 Washer 17 71447 1 Single Chain Restraint Collar 18 50053708 2 Screw 19 50053707 1 Shield Chain 20 78786 1 Danger Decal, Outer Tube 21 78608 1 Danger Decal, Shield 22 50053721 1 Ball Collar Kit 1-3/8” 23 50053705 1 Taper Pin Kit, 3 Pins 24 50053681 1 Half Shaft, Outer, Shielded 25 50053680 1 Half Shaft, Inner, Shielded 26 50053679 1 Complete Shield
23
10
QTY. DESCRIPTION
46-5-27
Page 78
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
SEPTEMBER, 2011
11 10
1
2
9
3
4
8
2
5
7
6
12
13
50018594 CROSS SHAFT WITH SHEARBOLT CLUTCH
1000 RPM – 1-3/4” – 20 Spline
Manufactured by Walterscheid
Model: 3214 (13214SS1)
REF. PART
NO. NO.
50018594 1 Driveline Assy w/Shear Bolt
1 50024795 1 Yoke 1-3/8” – 20 Spline 2 595BH 2 Cross and Bearing Kit 3 96494 1 Yoke & Bar Assembly 4 96495 1 Sleeve, Yoke & Tube Assembly 5 50024796 1 Shearbolt Clutch 6 44864 1 Capscrew 1/2” x 2-3/4” Gr.8 Blk. Oxide 7 15508 1 Hex Nut 1/2” 8 78786 1 Safety Decal
9 –––– 1 Capscrew 5/8” – 11 UNC x 3-1/4” Gr.8 10 –––– 1 Lockwasher 5/8” 11 –––– 1 Hex Nut 5/8” 12 –––– 2 Capscrew M16 x 2 x 80 13 –––– 2 Hex Nut M16
QTY. DESCRIPTION
46-5-28
Page 79
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
SEPTEMBER, 2011
18
10
16
2
1
12
3
1
4
5
14
15
20
7
6
8
9
19
11
13
17
9
50058059 DRIVESHAFT ASSEMBLY
540 RPM – 1-3/8” – 21 Spline
Manufactured by Bondioli & Pavesi
Model: 3214, 13214
REF. PART
NO. NO.
50058059 1 Driveshaft Assy
1 50062379 1 Yoke 2 50062380 2 Cross Kit 3 68765 1 Yoke, Outer Tube 4 66866 1 Roll Pin, Outer 5 50062381 1 Tube, Outer 6 50062382 1 Tube, Inner 7 66869 1 Roll Pin, Inner 8 68820 1 Yoke, Inner Tube
9 50062383 1 Rubber Shore 10 66875 1 Shield Support, Outer 11 66876 1 Shield Support, Inner 12 88789 1 Shield Cone, Outer 13 88808 1 Shield Cone, Inner 14 78786 1 Danger Decal, Outer Tube 15 78608 1 Danger Decal, Outer Shield Tube 16 90938 1 Taper Pin Kit, Z6 & Z21 17 83059 1 Taper Pin Kit, Z21 18 50062385 1 Female Half Shaft w/ Shield 19 50062386 1 Male Half Shaft w/ Shield 20 50062387 1 Complete Shield w/ Instruction Manual
QTY. DESCRIPTION
46-5-29
Page 80
Page 81
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-6-1
REF. PART
NO. NO.
QTY. DESCRIPTION
1 20150 2 Capscrew 1” x 8-1/2” Gr.5 2 9163200 2 Locknut 1”
*3 90412 2 Bushing 5-3/4” Long
94117 2 Bushing 5-21/32” Long 4 20325 6 Roll Pin 1/4” x 1-3/4” 5 88983 1 Pin 6 90591 1 Leveling Rod Assy. (3209)
90591 2 Leveling Rod Assy. (3214)
90415 2 Leveling Rod Assy. (3210) 7 15612 1 Jam Nut 1” 8 15908BH 2 Flatwasher 1” 9 53053BH 1 Turnbuckle
10 –––– 4 Cotter Pin 3/16” x 1-1/2” 11 90588 1 End Weldment 12 90592 1 Rod Weldment (3209, 3214)
90595 1 Rod Weldment (3210)
13 90599 2 Pin
92882 1 Tongue Assembly
14 87317 1 Important Decal 15 87340 1 Important Decal 16 92883 1 Tongue Weldment 17 92890 1 Clevis Weldment 18 85653 2 Pin 19 92889 1 Bushing
Old Style Clevis Assembly
20 15516 2 Locknut 5/8” 21 –––– 2 Capscrew 5/8” x 3-3/4” Gr.5 22 85649 1 Clevis Tongue Weldment 23 86356 1 Collar 24 86358 1 Clevis Weldment 25 24D25128 1 Jackstand Assembly
4
5
4
10
13
11
10
9
7
12
10
10
13
8
8
15
16
17
22
24
23
20
4
18
21
4
4
4
18
19
14
1
3
2
6
*Note: This part was changed from 5-3/4” to 5-21/32” in length. Determine which part is needed before ordering.
Do not interchange parts.
PULL TYPE HITCH
For All 3200 Series Pull Models
25
OLD STYLE CLEVIS ASSEMBLY
91074 SAFETY TOW CHAIN
SEPTEMBER, 2011
Page 82
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
REF. PART
NO. NO.
QTY. DESCRIPTION
1 –––– 1 Lockwasher 3/4” 2 15821 3 Lockwasher 1” 3 15908BH 2 Flatwasher 1” 4 19061 1 Capscrew 1” x5” Gr. 5 5 19502 3 Hex Nut 1” 6 –––– 1 Hex Nut 3/4” 7 20232BH 2 Capscrew 1” x 2 1/2” Gr.5 8 –––– 1 Capscrew 3/4” x 4 1/2” Gr.5
9 20558BH 2 Lynch Pin 10 44250BH 2 Capscrew 1” x 10 1/2” Gr.5 11 69528 2 Mast Link Bushing 12 9163200 2 Locknut 1” 13 25G12545 2 Hitch Pin 14 6404018 1 Mast Bushing 15 82000 1 Top Mast Bushing 16 90105 1 Slide Tube Weld. 17 90107BH 1 Mast Link Weldment (3209)
90165 1 Mast Link Weldment (3210)
18 90135 1 L.H. Mast Weldment (S/N 12-09999 and Below)
50017592 1 L.H. Mast Weldment (S/N 12-10000 and Above)
19 90136 1 R.H. Mast Weldment (S/N 12-09999 and Below)
50017593 1 R.H. Mast Weldment (S/N 12-10000 and Above) 20 20325 2 Roll Pin 1/4” x 1 3/4” 21 88983 1 Pin
3 POINT LIFT HITCH AND SEMI-MOUNT HITCH
For All 3209 & 3210 Lift & Semi-Mount Models
Note: Semi-Mount Hitch uses items 9 & 13
46-6-2
12
3
14
5
2
6
1
8
16
15
10
11
2
5
20
20
21
7
9
13
18
17
19
4
SEPTEMBER, 2011
Page 83
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
REF. PART
NO. NO.
QTY. DESCRIPTION
1 –––– 1 Lockwasher 3/4” 2 15821 3 Lockwasher 1” 3 15908BH 2 Flatwasher 1” 4 19061 1 Capscrew 1” x5” Gr. 5 5 19502 3 Hex Nut 1” 6 –––– 1 Hex Nut 3/4” 7 20232BH 2 Capscrew 1” x 2 1/2” Gr.5 8 –––– 1 Capscrew 3/4” x 4 1/2” Gr.5
9 20558BH 2 Lynch Pin 10 44250BH 2 Capscrew 1” x 10 1/2” Gr.5 11 69528 2 Mast Link Bushing 12 9163200 2 Locknut 1” 13 25G12545 2 Hitch Pin 14 90212 1 Mast Bushing 15 90213 1 Top Mast Bushing 16 90105 1 Slide Tube Weld. 17 90194 1 Mast Link Weldment 18 90317BH 1 Mast Weldment (3214 S/N 12-09999 and Below) 19 20325 2 Roll Pin 1/4” x 1 3/4” 20 88983 1 Pin
3 POINT LIFT HITCH AND SEMI-MOUNT HITCH
For All 3214 Models
46-6-3
12
3
14
5
2
6
1
8
16
15
10
11
2
5
19
19
20
7
9
13
18
17
4
SEPTEMBER, 2011
Page 84
Page 85
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
12
11
13
10
7
16
13
12
14
SEPTEMBER, 2011
20
3
2
1
15
6
5, 34
17
9
8
18
19
27
14
4
28
26
35
25
29
31
33
36
32
30
24
23
22
21
PULL TYPE AXLE ARMS & SPINDLES
For All 3200 Series Models
REF. PART
NO. NO.
1 20176 4 Capscrew 3/4” x 2 1/4” Gr. 8 2 –––– 4 Lockwasher 3/4” 3 –––– 4 Hex Nut 3/4” 4 44222BH 1 Capscrew 1/2-20 UNF x 4 1/2” 5 91055 1 Sandwich Mount Kit
6 67495 1 Sandwich Mount 7 20860 1 Capscrew 1” x 7 1/2” Gr.5 8 15612 1 Jam Nut 1”
9 19502 1 Hex Nut 1’’ 10 77660 1 Axle Stop 11 –––– 1 Capscrew 1/2” x 5 3/4” 12 –––– 2 Hex Nut 1/2” 13 –––– 2 Lockwasher 1/2” 14 15554 3 Locknut 1/2” 15 68643 1 Axle Clamp 16 68644 1 Axle Arm 17 –––– 2 Capscrew 1/2” x 3” Gr.5
QTY. DESCRIPTION
(Items 12, 13, 34)
Note: To convert from single axle to dual axle, order 50017967 Conversion Kit.
REF. PART
NO. NO.
67485 1 Single Spindle & Hub Assy. 77567 1 Dual Spindle & Hub Assy.
18 66658 1 Axle Weldment 19 67379 1 Spindle - Single Hub 20 77611 1 Spindle - Dual Hub 21 121BH 1 Hub Cap 22 120BH 1 Slotted Nut 3/4”-16 UNF 23 119 1 Flatwasher 3/4” 24 50073BH 1 Outer Bearing Cone 25 50076BH 1 Inner Bearing Cone 26 7967 1 Seal 27 296 1 Cotter Pin 1/8” x 1 1/2” 28 7977 1 Hub Assembly 29 7965 1 Hub Casting 30 15515BH 5 Nut 1/2”-20 UNF 31 15445 5 Bolt 1/2”-20 UNF 32 449BH 1 Grease Fitting 33 88921 1 Bearing Repair Kit 34 91042 1 Sandwich Mount 35 14-6-197 1 Bearing Cup 36 14-6-198 1 Bearing Cup
46-7-1
QTY. DESCRIPTION
Page 86
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
REF. PART
NO. NO.
QTY. DESCRIPTION
1 68643 1 Axle Clamp 2 77660 1 Axle Stop 3 20176 4 Capscrew 3/4” x 2 1/4” Gr.8 4 –––– 4 Lockwasher 3/4” 5 –––– 4 Hex Nut 3/4” 6 91055 1 Sandwich Mount Kit Items 8, 15, 16 7 44222BH 1 Capscrew 1/2” -20 UNF x 4 1/2” 8 91042 1 Sandwich Mount
9 20860 1 Capscrew 1” x 7 1/2” Gr.5 10 15612 1 Jamnut 1” 11 19502 1 Hex Nut 1” 12 –––– 1 Capscrew 1/2” x 5 3/4” 13 15554 1 Locknut 1/2” 14 68644 1 Axle Mount
*15 –––– 2 Hex Nut 1/2” *16 –––– 2 Lockwasher 1/2” *17 67495 1 Sandwich Mount
81522 1 Caster Assembly
18 19427BH 1 Roll Pin 1/2” x 2 1/4” 19 12262 1 Lock Collar 20 81523 1 Caster Arm 21 69900 1 Caster Weld. 22 69889 1 Thrust Washer
REF. PART
NO. NO.
QTY. DESCRIPTION
23 –––– 1 Cotter Pin 5/32” x 1 1/2” 24 50062BH 1 Seal 25 50076BH 1 Inner Bearing Cone 26 14-6-197 1 Inner Bearing Cup 27 50079 1 Hub w/Cups 28 15051 4 Lug 1/2”-20 UNF x 15/16” 29 14-6-198 1 Outer Bearing Cup 30 50073BH 1 Outer Bearing Cone 31 –––– 1 Flatwasher 5/8” 32 15183BH 1 Castle Nut 33 50054BH 1 Hub Cap 34 –––– 4 Lockwasher 1/2” 35 500BH 1 Tire Assy. 36 –––– 4 Capscrew 3/8” x 1” 37 233 2 Wheel Flange 38 56BH 1 Solid Tire 39 –––– 4 Lockwasher 3/8” 40 –––– 4 Hex Nut 3/8” 41 88924 1 Bearing Repair Kit
46-7-2
1
3
4
5
9
12
20
6, 8
17
16
15
15
40
39
37
38
37
36
35
13
29
28
34
27
18
22
21
7
41
33
16
2
14
11 10
19
TAILWHEEL ASSEMBLY
(SMALL TIRE)
For All Lift & Semi-Mount
Models 3209, 3210
23
32
30
31
26
25
24
*Note: These parts not used on 3209 Offeset models.
SEPTEMBER, 2011
Page 87
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
46-7-3
REF. PART
NO. NO.
QTY. DESCRIPTION
1 91055 1 Sandwich Mount Kit 2 —— 2 Hex Nut 1/2” - 13 UNC 3 15612 1 Jam Nut 1” - 8 UNC 4 —— 2 Lockwasher 1/2” 5 —— 1 Capscrew 1/2” - 13 UNC x 5-3/4” Gr. 5 6 —— 4 Lockwasher 3/4” 7 19502 1 Hex Nut 1” - 8 UNC 8 15554 1 Locknut 1/2” - 13 UNC
9 —— 4 Hex Nut 3/4” - 10 UNC 10 —— 4 Capscrew 3/4” - 10 UNC x 2-1/4” Gr. 5 11 20860 1 Capscrew 1” - 8 UNC x 7-1/2” Gr. 5 12 44222BH 1 Capscrew 1/2” - 20 UNF x 4-1/2” Gr. 5 13 91042 1 Sandwich Mount 14 67495 1 Sandwich Mount 15 68643 1 Axle Clamp 16 68644 1 Axle Arm Mount 17 77660 1 Axle Stop 18 18141206 2 Square Head Setscrew 3/8” - 16 UNC x 3/4” 19 1595BH 1 Spacer 2-3/8” Long 20 1596BH 1 Spacer 1-11/16” Long 21 1620BH 1 Spindle 22 7967 1 Triple Lip Seal
REF. PART
NO. NO.
QTY. DESCRIPTION
23 7968 1 Triple Lip Seal 24 15445 1 Wheel Bolt 25 15515BH 5 Lug Nut 26 15521 5 Locknut, Collar 27 50076BH 1 Bearing Cone 28 14-6-241 1 Bearing Cone 29 52732BH 1 Spirol Pin 30 81464 1 Caster Weld. 31 81467 1 Spacer 32 81472 1 Caster Arm Weld.
33 1613BH 1 Hub Assy.
34 449BH 1 Grease Fitting 35 1612 1 Hub 36 14-6-197 1 Bearing Cup 37 14-6-242 1 Bearing Cup
38 294SP 1 Wheel Assembly
39 116 1 Solid Tire 40 117 2 Wheel Flange 41 15597 5 Hex Nut 3/8” UNF 42 —— 5 Lockwasher 3/8” 43 20126 5 Capscrew 3/8” x 1” UNF
SINGLE TAILWHEEL ASSEMBLY (LARGE TIRE)
For Lift & Semi-Mount Models
3209, 3210, 3214
Note: Large Tire Tailwheel cannot be used on 3210 models with double row rear chains.
17
8
13
29
31
32
30
21
26
12
3
7
16
15
10
6
9
11
14
4
2
5
1
18
25
24
18
20
22
27
34
35
37
28
23
19
33
2
4
36
38
41
40
39
40
43
42
SEPTEMBER, 2011
Page 88
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
WHEELS & TIRES
PULL MODELS 3200 SERIES
SEPTEMBER, 2011
93048 SOLID TIRE
77SP AUTO RIM
5 HOLE 15”
46-7-4
Page 89
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
97708 AIRPLANE TIRE ASSEMBLY (AIR FILLED)
Replaced by 50050727SP Airplane Tire
50030908 AIRPLANE TIRE ASSEMBLY (FOAM FILLED)
SEPTEMBER, 2011
8
7
REF. PART
NO. NO.
1 97709 1 Tire 24 x 7.7 x 10 14/16 Ply 2 92860 1 Tube 5.5 x 10 3 92861 1 Wheel Flange w/ Hole for Tube Valve 4 92862 1 Wheel Flange wo/Hole for Tube Valve 5 92863 1 Inner Wheel Lining 6 –––– 10 Capscrew 1/2” x 1” Gr.5 7 –––– 10 Lockwasher 1/2” 8 –––– 10 Hex Nut 1/2”
QTY. DESCRIPTION
3
6
4
1
2
5
7
6
4
3
1
50050727SP AIRPLANE TIRE ASSEMBLY
5
2
REF. PART
NO. NO.
50050727SP 1 Airplane Tire Assy
1 50051233BH 1 Tire 29 x 9.0 – 15 / 16 Ply 2 50051234 1 Tube 9 x 15 3 50051235 1 Wheel Flange with Valve Hole 4 50051236 1 Wheel Flange without Valve Hole 5 –––– 10 Capscrew 1/2” x 1” Gr.5 6 –––– 10 Lockwasher 1/2” 7 –––– 10 Hex Nut 1/2”
46-7-5
Model: 3209, 3210, 3414
QTY. DESCRIPTION
Page 90
Page 91
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
REF. PART
NO. NO.
QTY. DESCRIPTION
1 63621 1 Locknut 2 84395 1 Bottom 3 63623 1 Plug 4 84398 4 Tie Rods 5 63638 4 Nuts 6 86624 1 Piston 7 86625 1 Clevis Rod 8 84397 1 Shaft
9 84396 1 Case 10 65650 1 Nylon Plug 11 63631 1 Set Screw 12 65651 2 Clevis Pin 13 63633 4 Pins 14 69032 1 Head Assy. 15 24-6-423 1 Safety Decal
16 86626 1 Seal Kit
86601 HYDRAULIC CYLINDER
3 1/2” Bore – 8” Stroke
3/4” – 16 SAE ORB Ports
Replaced by 99565 Hydraulic Cylinder
REF. PART
NO. NO.
QTY. DESCRIPTION
1 –––– 1 Flatwasher 5/8” 2 –––– 1 Capscrew 5/8” x 2” 3 –––– 1 Hex Nut 5/8” 4 12031 1 Hose Holder Rod
12032 HOSE HOLDER ASSY.
REF. PART
NO. NO.
QTY. DESCRIPTION
1 53340BH 1 Adaptor 9/16” JIC to 3/4” SAE 2 24-6-434 1 Adaptor 9/16” JIC to 1/2” NPT 3 14-40-98 1 90° Elbow 3/4” ORB to 9/16” JIC 4 50047240 1 Breather Plug 5 62427 1 Hydraulic Hose 144”
HYDRAULIC HOSES & FITTINGS
63451 STOP COLLAR KIT
46-8-1
SEPTEMBER, 2011
Page 92
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
SEPTEMBER, 2011
8 7
14
3
2
4
2
12
2
13 3 15 6 5 2 12 4 10
1
1
2
1
1817SP RATCHET ASSEMBLY
REF. PART
NO. NO.
1817SP 1 Ratchet Assy
1 50028265 2 Pin 2 50028264 4 Clip Pin 3 11810 1 Handle 4 15474 1 Cotter Pin
Cylinder Assembly Part Number Stamped Here.
QTY. DESCRIPTION
16
99565 HYDRAULIC CYLINDER
(Was Part No. 95394)
Mfd. by Monarch
3.5” Bore x 8” Stroke 1.25 Rod Dia. 3/4” – 16 ORB Ports
Replaced by 50047475 Cylinder (Bailey)
REF. PART
NO. NO.
1 95429 1 Clevis Cap 2 92430 1 Rod Cap 3 50017993 1 Piston 4 95431 1 Rod 1.25” Dia. 5 95426 1 Cylinder Tube 6 95427 4 Tie Rod 7 95425 2 Pin 1” Dia. 8 21020614 4 Cotter Pin 3/16” x 1 1/2”
9 95433 1 Thread Lock 10 95428 1 Rod Clevis 1.25” x 1” 11 95422 1 Set Screw 3/8” x 1/2 Knurled 12 95420 8 Hex Nut 5/8” UNF 13 95421 1 Hex Nut 1”-14 14 95435 1 Plug 3/4” 15 50042072 1 Caution Decal
16 50017623 1 Seal Kit
QTY. DESCRIPTION
11
9
8
7
46-8-2
Page 93
BUSH HOG / LAND MAINTENANCE REPAIR PARTS MANUAL
12
1
7
8
13
3
15
SEPTEMBER, 2011
Cylinder Assembly Part Number Stamped Here.
14
6
5
2
12
16
50047475 HYDRAULIC CYLINDER
Mfd. by Bailey
3.5” Bore x 8” Stroke, 1.25” Rod Dia. 3/4”–16 UNF Ports
4
11
9
8
10
7
REF. PART
NO. NO.
50047475 1 Hydraulic Cylinder Assy
1 –––– 1 Clevis Cap 2 –––– 1 Rod Cap 3 –––– 1 Piston 4 –––– 1 Rod 1.25” Dia. 5 –––– 1 Cylinder Tube 6 –––– 4 Tie Rod 7 –––– 2 Pin 1” Dia. 8 –––– 4 Cotter Pin 3/16” x 1 1/2”
9 –––– 1 Rod Clevis Bolt 10 –––– 1 Rod Clevis 1.25” x 1” 11 –––– 1 Rod Clevis Nut 12 –––– 8 Hex Nut 5/8” UNF 13 –––– 1 Hex Nut 1”-14 14 –––– 1 Plug 3/4” 15 –––– 1 Caution Decal
16 50017623 1 Seal Kit for 3.5” Bore
QTY. DESCRIPTION
46-8-3
Page 94
Page 95
Page 96
(334) 872-6261 • (334) 874-2700
Parts Ordering 1-800-304-2836
Fax 1-800-572-1784
www.bushhog.com
Loading...